{"product_id":"60105-mr-heater-ignition-board","title":"60105 Ignition Control Board for Mr Heater HeatStar MHU HSU Heaters","description":"\n\u003ch2\u003e60105 Ignition Control Board for Mr Heater \/ HeatStar — 6-Pin Direct Replacement for MHU \u0026amp; HSU Unit Heaters up to 125,000 BTU\u003c\/h2\u003e\n\u003cp\u003eThe iFJF 60105 is a \u003cstrong\u003e6-pin ignition control board\u003c\/strong\u003e for Mr. Heater, HeatStar, Big Maxx and Enerco overhead unit heaters. It is the board sold under Enerco part number \u003cstrong\u003e60105\u003c\/strong\u003e, runs on a \u003cstrong\u003e24 VAC\u003c\/strong\u003e control circuit, and fits the \u003cstrong\u003eMHU45 \/ 50 \/ 55 \/ 70 \/ 75 \/ 80 \/ 125\u003c\/strong\u003e and \u003cstrong\u003eHSU45 \/ 50 \/ 55 \/ 70 \/ 75 \/ 80 \/ 125\u003c\/strong\u003e series in both propane (LP) and natural gas (NG) — every unit rated up to 125,000 BTU. It uses the same Molex connector, the same terminal layout and the same mounting posts as the board it replaces, so the swap is a plug-in job with no rewiring.\u003c\/p\u003e\n\u003cp\u003eThe board runs the whole light-off sequence: inducer pre-purge, igniter power, gas valve opening, flame proving by rectification, then blower timing. It also watches the safety string — pressure switch, rollout switch, limit — and reports what it finds with \u003cstrong\u003efault-code flashes from the on-board LED\u003c\/strong\u003e, which is the fastest way to tell a dead board from an open safety switch. If the blower runs and the burner never lights, or the heater fires and drops out a few seconds later until it locks out, read the flash code before you buy anything.\u003c\/p\u003e\n\n\n\u003ch3\u003eKey Features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eOne Board, Two Model Families:\u003c\/strong\u003e Covers all Mr. Heater MHU and HeatStar HSU sizes from 45,000 to 125,000 BTU — a single spare covers a whole fleet of garage and workshop heaters.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLP and NG, Same Board:\u003c\/strong\u003e The same 60105 runs both the propane and natural gas version of each model. Gas type is set by the orifices and gas valve springs in your heater, not by the board.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e6-Pin Molex Interface:\u003c\/strong\u003e The latest 6-pin connector style. It presses onto the factory harness and seats in one orientation — no splicing, no adapter, no field wiring.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFlame Proving \u0026amp; Lockout:\u003c\/strong\u003e Proves flame by rectification on every trial for ignition and shuts the gas valve on flame failure instead of letting raw gas into the heat exchanger.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFault-Code LED:\u003c\/strong\u003e Flashes a stored code for the fault it found, so you can separate an open pressure switch or rollout from a failed board before ordering parts.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInducer \u0026amp; Blower Sequencing:\u003c\/strong\u003e Starts the inducer, holds the blower until the cabinet warms, and runs it on after the burner drops out to sweep residual heat.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMatching Footprint:\u003c\/strong\u003e Sits on the same four mounting posts with the same terminal positions — about 5.7\" × 4.5\" × 1.5\".\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBench-Checked Before Shipping:\u003c\/strong\u003e Every board is inspected before it leaves the warehouse. Backed by iFJF Quality Guarantee · Easy Returns · Wiring Support.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\n\u003ch3\u003eCompatibility \/ Fitment\u003c\/h3\u003e\n\u003cdiv style=\"font-size:0.95em;color:#555;margin-bottom:8px;\"\u003eFits Mr. Heater, HeatStar, Big Maxx and Enerco overhead unit heaters. Each size below is covered in \u003cstrong\u003eboth LP and NG\u003c\/strong\u003e versions. Confirm the number on the board you are removing — and check the connector style note under the table — before ordering.\u003c\/div\u003e\n\u003cdiv style=\"overflow-x:auto;clear:both;width:100%;-webkit-overflow-scrolling:touch;\"\u003e\u003ctable style=\"width:100%;table-layout:fixed;word-wrap:break-word;\"\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth style=\"width:30%;\"\u003eSeries\u003c\/th\u003e\n\u003cth style=\"width:34%;\"\u003eModels Covered (LP \u0026amp; NG)\u003c\/th\u003e\n\u003cth\u003eInput Rating\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMr. Heater MHU\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eMHU45, MHU50, MHU55, MHU70, MHU75, MHU80, MHU125\u003c\/td\u003e\n\u003ctd\u003e45,000 – 125,000 BTU\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eHeatStar HSU\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eHSU45, HSU50, HSU55, HSU70, HSU75, HSU80, HSU125\u003c\/td\u003e\n\u003ctd\u003e45,000 – 125,000 BTU\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eBig Maxx \/ Enerco\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eUnits of the same platform sold under these labels\u003c\/td\u003e\n\u003ctd\u003eUp to 125,000 BTU\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMounting\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eVertical or horizontal overhead installation\u003c\/td\u003e\n\u003ctd\u003eGarage, workshop, commercial\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003c\/div\u003e\n\u003cdiv style=\"background:#fff8e1;border:1px solid #ffe082;border-radius:4px;padding:12px;margin:12px 0;\"\u003e\n\u003cstrong\u003e⚠️ Check your connector before ordering.\u003c\/strong\u003e On some older Mr. Heater and HeatStar units the 6 pins inside the plastic Molex connector were \u003cstrong\u003efemale pins\u003c\/strong\u003e (those boards were made by NOVAR Controls). The 60105 is the newer \u003cstrong\u003emale-pin\u003c\/strong\u003e board: it will replace a NOVAR board, but only if you also fit the \u003cstrong\u003e60104 ignition harness\u003c\/strong\u003e, which is not included. Pull the connector off your old board and look at the pins — if the pins sit inside the board-side socket, send us a photo before you order.\n\u003c\/div\u003e\n\n\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cdiv style=\"overflow-x:auto;clear:both;width:100%;-webkit-overflow-scrolling:touch;\"\u003e\u003ctable style=\"width:100%;table-layout:fixed;word-wrap:break-word;\"\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth style=\"width:40%;\"\u003eSpecification\u003c\/th\u003e\n\u003cth\u003eValue\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003ePart Number\u003c\/td\u003e\n\u003ctd\u003e\u003cstrong\u003e60105\u003c\/strong\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eComponent Type\u003c\/td\u003e\n\u003ctd\u003eAutomatic ignition control board (unit heater)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eControl Voltage\u003c\/td\u003e\n\u003ctd\u003e24 VAC, 50\/60 Hz\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eConnector\u003c\/td\u003e\n\u003ctd\u003e6-pin Molex, male pins (newer style)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFuel\u003c\/td\u003e\n\u003ctd\u003ePropane (LP) or natural gas (NG) — same board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFits Input Range\u003c\/td\u003e\n\u003ctd\u003eUp to 125,000 BTU\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFunctions\u003c\/td\u003e\n\u003ctd\u003eIgnition timing, inducer, gas valve, flame rectification, blower delay, safety interlocks\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDiagnostics\u003c\/td\u003e\n\u003ctd\u003eOn-board LED fault-code flashes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBoard Size\u003c\/td\u003e\n\u003ctd\u003eApprox. 5.7\" × 4.5\" × 1.5\" (145 × 114 × 38 mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePackage Weight\u003c\/td\u003e\n\u003ctd\u003e12 oz (340 g)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eIncludes\u003c\/td\u003e\n\u003ctd\u003e1 × 60105 ignition control board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eQuality\u003c\/td\u003e\n\u003ctd\u003eiFJF Quality Guarantee\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003c\/div\u003e\n\n\n\u003ch3\u003eInstallation Tips\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cstrong\u003eKill both supplies.\u003c\/strong\u003e Open the breaker feeding the unit \u003cem\u003eand\u003c\/em\u003e close the manual gas valve. The 24 VAC control circuit is fed from the transformer inside the heater, so the wall thermostat being off is not enough.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRead the flash code first.\u003c\/strong\u003e Before you pull the old board, power the unit up and count the LED flashes. That code tells you whether the board saw an open pressure switch, a rollout trip or a flame failure — and it is gone once the board is out.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePhotograph the connectors.\u003c\/strong\u003e One phone photo of the old board with the 6-pin harness and every spade lead in place saves more time than any wiring diagram.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCheck the pin style.\u003c\/strong\u003e Male pins on the board side accept the standard harness. If the old board had female pins in the connector (NOVAR style), you need the 60104 harness — stop and order it rather than forcing the connector.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNever force the Molex plug.\u003c\/strong\u003e The 6-pin connector only seats one way. If it resists, the pins are misaligned by one position — pull it off and look before pushing harder.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMove the spade leads one at a time.\u003c\/strong\u003e Transfer each lead from the old board to the matching terminal before starting the next, instead of pulling them all off first.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWatch the first cycle.\u003c\/strong\u003e Inducer starts → igniter glows → gas valve opens → burners light → blower starts after the delay. If the burner lights and drops out within seconds, clean the flame sensor and check the pressure switch tubing before blaming the new board.\u003c\/li\u003e\n\u003c\/ol\u003e\n\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003ch4\u003eQ: What part number is this board and what does it replace?\u003c\/h4\u003e\n\u003cp\u003eA: It is the 60105 ignition control board, the Enerco part number used across Mr. Heater, HeatStar, Big Maxx and Enerco overhead unit heaters. The same board is sold under those brand labels, so 60105 is the number to match. Compare it with the number printed on the board you are removing, and check that your heater has the newer 6-pin male-pin connector before ordering.\u003c\/p\u003e\n\u003ch4\u003eQ: Which Mr. Heater and HeatStar heaters use the 60105 board?\u003c\/h4\u003e\n\u003cp\u003eA: The Mr. Heater MHU series (MHU45, MHU50, MHU55, MHU70, MHU75, MHU80, MHU125) and the HeatStar HSU series (HSU45, HSU50, HSU55, HSU70, HSU75, HSU80, HSU125), in both propane and natural gas versions. Every model in that range is rated up to 125,000 BTU. Because the same board is shared across the whole family, the part number on your old board is the reliable check, not the model badge alone.\u003c\/p\u003e\n\u003ch4\u003eQ: How do I tell the newer 6-pin board from the older NOVAR board?\u003c\/h4\u003e\n\u003cp\u003eA: Pull the 6-pin Molex connector off the old board and look at the pins. On the newer style the pins stand up on the board and go into the harness plug. On the older NOVAR boards the pins were female and sat inside the board-side connector, and those boards were marked near the Y C W G R screw terminals. A 60105 will replace a NOVAR board, but you also need the 60104 ignition harness, which is not included. Send us a photo of the connector if you are unsure.\u003c\/p\u003e\n\u003ch4\u003eQ: My blower runs but the burner never lights. Is the board bad?\u003c\/h4\u003e\n\u003cp\u003eA: Not necessarily - read the LED flash code before buying anything. A blinking code points at a specific fault: a pressure switch that never closes (blocked tubing, water in the hose, blocked flue), a rollout switch that tripped, a limit that opened, or a flame that failed to prove. Clean the flame sensor and check the pressure switch tubing first, since both produce the same no-heat symptom as a dead board. If the code says ignition failure and the igniter does not glow, or the heater locks out immediately after the gas valve should open, the board is the usual cause.\u003c\/p\u003e\n\u003ch4\u003eQ: Does the 60105 work on both propane and natural gas heaters?\u003c\/h4\u003e\n\u003cp\u003eA: Yes. It is the same board for the LP and NG version of each model. The fuel type is set by the orifices and gas valve springs in the heater, not by the control board, so you do not need a separate part number for propane.\u003c\/p\u003e\n\u003ch4\u003eQ: Is this a genuine Enerco board or an aftermarket replacement?\u003c\/h4\u003e\n\u003cp\u003eA: It is an iFJF aftermarket replacement built to the same fitment and function as the factory board. Mr. Heater, HeatStar, Big Maxx and Enerco part numbers are referenced for identification only and remain the property of their owners. It is covered by the iFJF Quality Guarantee, with Easy Returns and Wiring Support if the connector does not line up.\u003c\/p\u003e\n\n\u003ch3\u003e📊 iFJF 60105 vs the Factory Board\u003c\/h3\u003e\n\u003cp\u003eSame footprint, same connector, same sequence. The difference is where you buy it and how fast you can get a spare back into a cold shop.\u003c\/p\u003e\n\u003cdiv style=\"overflow-x:auto;clear:both;width:100%;-webkit-overflow-scrolling:touch;\"\u003e\u003ctable style=\"width:100%;table-layout:fixed;word-wrap:break-word;\"\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth style=\"width:26%;\"\u003eFeature\u003c\/th\u003e\n\u003cth style=\"width:37%;\"\u003eFactory Enerco Board\u003c\/th\u003e\n\u003cth\u003eiFJF 60105\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePart number\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e60105\u003c\/td\u003e\n\u003ctd\u003e60105 (direct cross)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eConnector\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e6-pin Molex, male pins\u003c\/td\u003e\n\u003ctd\u003e6-pin Molex, male pins\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eControl voltage\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e24 VAC\u003c\/td\u003e\n\u003ctd\u003e24 VAC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eModel coverage\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eMHU \/ HSU 45–125, LP and NG\u003c\/td\u003e\n\u003ctd\u003eMHU \/ HSU 45–125, LP and NG\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eFault diagnostics\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eLED flash codes\u003c\/td\u003e\n\u003ctd\u003eLED flash codes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMounting\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eFactory posts\u003c\/td\u003e\n\u003ctd\u003eFactory posts, no drilling\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eBuying channel\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eHVAC \/ hearth dealer, often special order\u003c\/td\u003e\n\u003ctd\u003eOrder direct, in stock and ready to ship\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003c\/div\u003e\n\n\n\u003ch3\u003e📦 Related Products \u0026amp; Guides\u003c\/h3\u003e\n\u003cp\u003eHeating a shop or a house? These are the control boards our customers compare with the 60105 most often.\u003c\/p\u003e\n\u003cdiv style=\"overflow-x:auto;clear:both;width:100%;-webkit-overflow-scrolling:touch;\"\u003e\u003ctable style=\"width:100%;table-layout:fixed;word-wrap:break-word;\"\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth style=\"width:44%;\"\u003eProduct\u003c\/th\u003e\n\u003cth style=\"width:40%;\"\u003eFits\u003c\/th\u003e\n\u003cth\u003ePrice\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/products\/94w83-furnace-control-board\"\u003e94W83 Furnace Control Board\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eLennox gas furnaces — replaces 103085-02 \/ -03\u003c\/td\u003e\n\u003ctd\u003e$93.99\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/products\/903429-furnace-control-board-nordyne-m1\"\u003e903429 Furnace Control Board\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eNordyne \/ Intertherm M1M furnaces\u003c\/td\u003e\n\u003ctd\u003e$89.99\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/products\/031-01267-001a-furnace-control-board\"\u003e031-01267-001A Furnace Control Board\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eYork, Luxaire \u0026amp; Coleman 120 V HSI furnaces\u003c\/td\u003e\n\u003ctd\u003e$89.99\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/products\/50a55-843-furnace-control-board-compatible-white-rodgers-lennox\"\u003e50A55-843 Furnace Control Board\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eLennox \u0026amp; White-Rodgers gas furnaces\u003c\/td\u003e\n\u003ctd\u003e$137.99\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003c\/div\u003e\n\u003cp\u003eBrowse the full range of \u003ca href=\"\/collections\/electronics\"\u003eHVAC control boards and electronics\u003c\/a\u003e, or see every \u003ca href=\"\/collections\/home-garden\"\u003ehome \u0026amp; garden heating part\u003c\/a\u003e we stock.\u003c\/p\u003e\n\n\n\u003ch3\u003e🔄 60105 Cross Reference \u0026amp; Old-Board Notes\u003c\/h3\u003e\n\u003cdiv style=\"overflow-x:auto;clear:both;width:100%;-webkit-overflow-scrolling:touch;\"\u003e\u003ctable style=\"width:100%;table-layout:fixed;word-wrap:break-word;\"\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth style=\"width:34%;\"\u003eNumber\u003c\/th\u003e\n\u003cth\u003eWhat It Is\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003e60105\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eEnerco ignition control board — iFJF equivalent\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003e60104\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eIgnition wire harness — only needed when replacing an older NOVAR board, not included\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMHU45 – MHU125\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eMr. Heater overhead unit heaters using the 60105 board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eHSU45 – HSU125\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eHeatStar overhead unit heaters using the 60105 board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003c\/div\u003e\n\u003cp style=\"font-size:0.9em;color:#555;\"\u003eThe 60105 is sold under the Mr. Heater, HeatStar, Big Maxx and Enerco labels — the part number is the same across all of them. Brand and part numbers are listed for identification only. The 60105 is an ignition control board: it does not include the blower, the gas valve, the igniter or the 60104 harness.\u003c\/p\u003e\n\n\n\u003cdiv style=\"background:#f0f7ff;border:1px solid #b8d4f0;border-radius:6px;padding:16px;margin-top:20px;\"\u003e\n\u003cstrong\u003eNot sure which board your heater has?\u003c\/strong\u003e Send us a photo of the existing board with the part number visible, a photo of the 6-pin connector showing the pins, and the model and serial numbers from the rating plate. Our team will confirm the match before you order.\u003cbr\u003e\n\u003cstrong\u003eEmail:\u003c\/strong\u003e support@ifjf.com\u003cbr\u003e\n\u003cspan style=\"font-size:0.9em;\"\u003eBacked by \u003cstrong\u003eISO 9001:2015\u003c\/strong\u003e and \u003cstrong\u003eIATF 16949:2016\u003c\/strong\u003e quality management system certifications.\u003c\/span\u003e\n\u003c\/div\u003e\n","brand":"iFJF","offers":[{"title":"Default Title","offer_id":52459171643638,"sku":"FJ-CB-60105","price":79.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0606\/3836\/3894\/files\/60105-mr-heater-ignition-board-01.jpg?v=1795236006","url":"https:\/\/ifjf.net\/products\/60105-mr-heater-ignition-board","provider":"iFJF Direct","version":"1.0","type":"link"}