Products

Product Overview Upgrade your GM LS engine's oiling system with the iFJF Billet Aluminum Oil Bypass & Barbell Kit. The factory plastic barbell (oil gallery plug) in LS engines is a known failure point — when it cracks or deteriorates, you lose oil pressure to the rear of the engine, often leading to catastrophic bearing failure. Our CNC-machined 6061-T6 aluminum replacement eliminates this risk permanently. Designed for all GM LS-based engines including LS1, LS2, LS3, LS6, LQ4, LQ9, and LSX variants. Whether you're doing an LS swap, rebuilding, or just performing preventive maintenance, this kit is essential insurance for your engine. Key Features CNC-Machined 6061-T6 Billet Aluminum — Will never crack, shrink, or deteriorate like stock plastic Complete Kit — Includes oil bypass barbell + rear cover alignment dowels Precision O-Ring Grooves — Properly machined for leak-free oil gallery sealing Anodized Finish — Corrosion-resistant for long-term reliability Lifetime Warranty — Built to outlast your engine Why Replace the Stock Plastic Barbell? The OEM plastic barbell oil plug is a cost-cutting part that degrades over time from heat cycling and oil exposure. When it fails: Oil pressure drops (especially at idle) Rear main bearings and cam bearings starve for oil Engine damage can occur within seconds of pressure loss Common failure point on high-mileage and high-performance LS builds If you're rebuilding an LS or pulling the rear cover for any reason, replace the plastic barbell with billet aluminum — it's cheap insurance against a multi-thousand-dollar engine failure. Compatibility Engine Displacement Applications LS1 5.7L 1997-2004 Corvette, Camaro, Firebird, GTO LS2 6.0L 2005-2007 Corvette, GTO, TrailBlazer SS, SSR LS3 / L99 6.2L 2008-2015 Corvette, Camaro SS, G8 GXP LS6 5.7L 2001-2004 Corvette Z06, CTS-V LQ4 / LQ9 6.0L 1999-2007 Silverado, Sierra, Escalade, Denali LSX / LS7 7.0L+ Aftermarket LS blocks, Z06 LM7 / LR4 / LM4 / L33 4.8L / 5.3L 1999-2007 Truck/SUV Specifications Specification Value Material 6061-T6 Billet Aluminum Finish Clear Anodized Includes Barbell + 2x Alignment Dowels Manufacturing CNC Machined Warranty Lifetime Frequently Asked Questions Q: Do I need to pull the engine to install this?A: No. The barbell is located behind the rear engine cover (between engine and transmission). It's accessible when the transmission or rear cover is removed — common during clutch replacement, rear main seal service, or engine rebuild. On some vehicles, you can access it by removing the rear cover with the engine in the vehicle. Q: Will this fit my 2004 Silverado 5.3L LM7?A: Yes. This kit fits ALL Gen III and Gen IV LS-based engines regardless of displacement. The oil gallery design is universal across the LS platform. Q: Is this just the barbell, or does it include the rear cover?A: This kit includes the billet aluminum barbell (oil gallery plug) and alignment dowels. The rear cover is NOT included — you reuse your factory rear cover or aftermarket replacement. Q: Do I need sealant to install this?A: The barbell uses O-rings for sealing — no sealant required. Just lubricate the O-rings with clean engine oil before installation and ensure the bores are clean. Q: Is this necessary for a stock rebuild?A: Highly recommended. The factory plastic barbell costs pennies to produce and is a known failure point even on stock engines. For the cost of this kit vs. a potential engine failure, it's a no-brainer. Related Products Front & Rear Cover Alignment Tool Kit — Perfect companion for LS builds Browse All Engine Parts Related Blog Posts LS Engine Building Tips & Common Failure Points

Read more less

Product Overview Restore your Norcold RV refrigerator's cooling performance with this 300W heating element, a direct replacement for Norcold part number 630811. When your Norcold fridge stops cooling on electric mode but works fine on gas, the heating element is the most likely culprit. This OEM-spec replacement gets your fridge back to reliable electric operation without the cost of a complete cooling unit. Compatible with Norcold N611, N621, N811, N821, N841, and other Norcold absorption refrigerator models that use 300W AC heating elements. Key Features 300W / 120V AC — Exact match for OEM specifications Direct Plug-and-Play Replacement — Same form factor and electrical connectors as factory unit High-Temperature Nickel-Chromium Alloy — Durable heating element wire rated for continuous duty Stainless Steel Sheath — Corrosion-resistant for long service life in RV environments Thermal Fuse Protection — Built-in safety cutoff prevents overheating Symptoms of a Failed Heating Element Fridge cools on LP gas but NOT on AC electric mode Fridge doesn't cool at all on any mode (check control board as well) Circuit breaker trips when fridge is switched to electric mode No heat felt at boiler area when running on AC Ammonia smell (indicates cooling unit leak — different problem) Compatibility Brand Models Norcold N611, N621, N811, N821, N841 (300W AC versions) Part Number 630811 Specifications Specification Value Power Rating 300 Watts Voltage 120V AC Element Material Nickel-Chromium Alloy Sheath Material Stainless Steel Replaces Part # 630811 Frequently Asked Questions Q: How do I diagnose if my heating element is bad?A: Test with a multimeter: disconnect power, remove element leads, and measure resistance. A good 300W element should read approximately 48 ohms. An open circuit (infinite resistance) means the element is burned out. Q: Can I replace this myself?A: Yes — if you're comfortable with basic electrical work and have access to the back of the refrigerator (through the exterior access panel). Disconnect all power sources (120V AC and 12V DC) before servicing. Q: Will this fit my Norcold N841?A: Yes, this 300W element fits Norcold N6xx and N8xx series refrigerators that use 300W AC electric heating elements. Verify your specific model's wattage before ordering. Q: My fridge doesn't cool on gas either — will this fix it?A: No. If your fridge fails on both gas and electric, the problem is likely a failed cooling unit (ammonia leak), blocked burner orifice, or control board issue — not the heating element. Related Products RV Winterizing Kit — Prepare your RV for storage Browse All RV Parts & Accessories Related Blog Posts RV Appliance Troubleshooting Guide

Read more less

Product Overview Keep your Onan QG generator starting on the first crank with these premium replacement spark plugs. Direct replacement for Onan part number 167-1638, these plugs are engineered for the high-hour duty cycles of RV generators. Compatible with Onan QG 5500 and 7000 models (HGJAA, HGJAB, HGJAC). Worn spark plugs are the #1 cause of hard starting and rough running in RV generators — replace annually or every 150 hours for reliable performance. Key Features Direct OEM Replacement — Replaces Onan 167-1638 Nickel-Plated Shell — Anti-seize and corrosion-resistant Copper-Core Electrode — Superior heat dissipation and conductivity Pre-Gapped — Factory-set to OEM specification; ready to install Pack of 2 — Both plugs for twin-cylinder QG generators Compatibility Generator Model Spec Codes Power Onan QG 5500 HGJAA, HGJAB, HGJAC 5,500W Onan QG 7000 HGJAA, HGJAB, HGJAC 7,000W Specifications Specification Value Part Number 167-1638 Thread Size 14mm x 1.25 Reach 19mm (3/4") Hex Size 5/8" (16mm) Gap Pre-gapped to OEM spec Quantity 2 Pack Frequently Asked Questions Q: How often should I change generator spark plugs?A: Onan recommends spark plug replacement every 150 hours or annually, whichever comes first. If your generator sees heavy use or runs in dusty conditions, consider more frequent replacement. Q: What are signs my spark plugs need replacing?A: Hard starting, rough idle, surging under load, increased fuel consumption, or visible electrode wear/carbon fouling on inspection. Q: Does this pack include 2 plugs?A: Yes, this is a 2-pack — enough for both cylinders on the QG 5500 and 7000 twin-cylinder generators. Q: Are these pre-gapped?A: Yes, factory pre-gapped to OEM specification. Always verify gap before installation as a best practice, but they should be ready to install out of the box. Related Products Onan Generator Air Filter 140-3116 — Complete tune-up Browse All RV Generator Parts Related Blog Posts RV Generator Maintenance Schedule & Tips

Read more less

Product Overview Winterize your RV in minutes — not hours — with the iFJF RV Winterizing Kit. This blow-out adapter connects your air compressor to your RV's city water inlet, allowing you to purge all water from the plumbing system with compressed air. Includes a premium brass shut-off valve for controlled air flow and a quick-connect air compressor fitting for fast setup. Frozen pipes can cause thousands of dollars in damage to your RV's plumbing system. This kit provides a clean, antifreeze-free winterization method preferred by many RV owners — no pink antifreeze taste in your water lines next spring. Key Features Complete Kit — Blow-out plug, brass shut-off valve, quick-connect air fitting Brass Construction — Durable, corrosion-resistant, built to last season after season Quick-Connect Fitting — Standard 1/4" industrial quick-connect for any air compressor Adjustable Air Flow — Brass ball valve provides precise air pressure control Universal Fit — Works with standard RV city water inlet connections How to Winterize Your RV with This Kit Drain all holding tanks (fresh, gray, black) completely Open all faucets, shower heads, and toilet valves Connect blow-out adapter to RV city water inlet Connect air compressor (set to 30-40 PSI MAX — do NOT exceed 50 PSI) Open brass valve gradually and blow air through system Close each faucet as water stops and only air comes out Don't forget: outdoor shower, toilet sprayer, ice maker line, and low-point drains Pour RV antifreeze into all drain P-traps (sinks, shower, toilet bowl) Compatibility Application Details RV / Camper / Motorhome Standard city water inlet Air Compressor 1/4" industrial quick-connect Water Inlet Thread Standard garden hose thread (GHT) Specifications Specification Value Material Brass body + brass ball valve Air Fitting 1/4" Industrial Quick-Connect (male) Water Connection Standard Garden Hose Thread Max Air Pressure 50 PSI (recommend 30-40 PSI) Shut-Off Brass Ball Valve (1/4 turn) Frequently Asked Questions Q: Do I still need RV antifreeze if I use this?A: You still need to pour antifreeze into drain P-traps (sinks, shower, toilet). The blow-out method clears the water lines but does NOT protect the traps. A gallon of RV antifreeze for traps is still recommended. Q: What PSI should I set my compressor to?A: 30-40 PSI is ideal. Never exceed 50 PSI — RV plumbing is designed for 40-60 PSI water pressure, and air pressure is more aggressive. Start low and increase only if needed. Q: Will this work with any air compressor?A: Yes, as long as your compressor has a standard 1/4" industrial quick-connect coupler (the most common type). Works with pancake, hot dog, and portable compressors. Q: Is the blow-out method better than using antifreeze?A: Both methods work. Many RVers prefer the blow-out method because it leaves no antifreeze residue in the water lines (no pink taste in spring). Others use antifreeze for peace of mind. Some do both for maximum protection in extreme cold climates. Related Products Norcold RV Fridge Heating Element Browse All RV Parts & Accessories Related Blog Posts Complete RV Winterization Checklist

Read more less

Product Overview Breathe cleaner air in your Tesla Model 3 with this premium cabin air filter featuring activated carbon and soda-infused media for superior odor, allergen, and particulate filtration. A direct replacement for the factory filter, this upgrade filters out pollen, dust, mold spores, exhaust fumes, and VOCs — keeping your cabin air fresh and clean for you and your passengers. Tesla recommends replacing the cabin air filter every 2 years (or every 1 year in high-pollution areas). A clogged filter reduces HVAC efficiency and can cause musty odors from the AC system. Our activated carbon upgrade outperforms the stock paper filter at a fraction of Tesla's service center price. Key Features Activated Carbon Layer — Adsorbs VOCs, exhaust fumes, ozone, and industrial odors Soda-Infused Media — Enhanced acid-gas filtration for urban environments HEPA-Grade Efficiency — Filters 99.97% of particles ≥0.3 microns Perfect Fit — Precision-cut to Tesla Model 3 filter housing dimensions (2017-2025) Easy DIY Install — Tesla-friendly design; installs in 10 minutes with basic tools Compatibility Vehicle Years Tesla Model 3 2017–2025 (All Trims: SR+, LR, Performance) Specifications Specification Value Filter Media Activated Carbon + Soda-Infused Non-Woven Filtration Efficiency ≥99.97% @ 0.3 microns Filter Type Cabin Air Filter (Particle + Gas Combination) Replacement Interval Every 2 Years or 15,000 Miles Signs Your Cabin Air Filter Needs Replacement Musty or sour smell from AC vents Reduced airflow from HVAC system Excessive window fogging in humid weather Increased allergy symptoms while driving Visible debris or discoloration on filter inspection Frequently Asked Questions Q: How do I replace the Model 3 cabin air filter?A: The Model 3 filter is accessed from inside the cabin (passenger footwell area). Remove the footwell cover panel, release the filter housing door, slide out the old filter, and insert the new one ensuring correct airflow direction (arrow on filter). 10-15 minute DIY job. Q: How often should I replace the cabin air filter?A: Tesla recommends every 2 years. If you drive in heavy traffic, areas with wildfires, or high-pollen seasons, consider replacing annually for best air quality. Q: Does this fit the 2024 Model 3 Highland?A: Yes. The cabin air filter dimensions remained unchanged through all Model 3 iterations including the 2024 Highland refresh. Q: Is this better than the OEM Tesla filter?A: Our filter uses activated carbon + soda-infused media which provides superior gas/odor filtration compared to the standard OE paper filter. Same fit, better filtration. Related Products Tesla Model X Trunk Sill Guard Browse All Tesla Accessories Related Blog Posts Tesla Model 3 DIY Maintenance Guide

Read more less

Product Overview Fix your Yamaha Banshee's notorious TORS (Throttle Override System) issues once and for all with this complete TORS Removal Kit. If your Banshee is stalling, idling erratically, or bogging at part-throttle, the TORS parking brake limiter is the most likely culprit. This kit eliminates the problematic TORS system and gives you direct carburetor control. Compatible with 1987-2006 Yamaha Banshee 350 (all years). This is the #1 recommended modification for any Banshee — even stock machines benefit from TORS removal. Key Features Complete Kit — Includes idle screws, carb caps, and throttle cable caps Eliminates Stalling & Erratic Idle — No more TORS-related electrical gremlins Adjustable Idle — Manual idle adjustment screws give you full control Quick Install — 30-minute bolt-on modification, no fabrication required OEM-Quality Materials — Billet aluminum caps with proper O-ring seals What Is TORS & Why Remove It? TORS (Throttle Override System) is an early electronic safety system that monitors throttle position vs. carburetor slide position. When the parking brake microswitch gets dirty, the TORS brain box cuts ignition — causing stalling, bogging, and refusal to rev. On 30+ year-old machines, the wiring, brain box, and parking brake switch are almost certainly malfunctioning. This kit replaces the electronic TORS caps with manual idle screws, giving you direct, mechanical control over idle speed and eliminating all TORS-related electrical failures. Note: This kit is intended for off-road/competition use only. Not for street-legal vehicles. Compatibility Vehicle Years Engine Yamaha Banshee 350 1987–2006 347cc 2-Stroke Twin Kit Contents Component Quantity Idle Adjustment Screws 2 Carburetor Caps (TORS Delete) 2 Thumb Throttle Cable Caps 2 O-Rings & Hardware Complete Frequently Asked Questions Q: Will this completely eliminate my stalling issue?A: If your stalling is TORS-related (the most common cause on Banshees), yes. The TORS brain box and parking brake switch are the #1 cause of intermittent stalling on Banshees. If stalling persists after TORS removal, check your reeds, coil, stator, and carb jetting. Q: Is this difficult to install?A: No — this is a straightforward 30-minute bolt-on install. Remove the stock TORS carb caps, install the new caps + idle screws, replace the throttle cable caps, adjust idle, and you're done. Basic hand tools only. Q: Do I need to re-jet after TORS removal?A: Not necessarily. TORS removal doesn't change airflow or fuel delivery — it just replaces the electronic caps with manual ones. However, if your Banshee has other mods (pipes, air filter, etc.), you should already be jetted accordingly. Q: Can I leave the TORS brain box connected after installing this?A: You can physically leave it in place, but it will no longer have any function. Some riders remove it entirely to clean up the wiring. Unplug the parking brake switch connector as well. Q: Is this legal for street use?A: No. TORS is a safety system, and removing it makes the vehicle for off-road/competition use only. Not street legal in any jurisdiction. Related Products Browse All ATV & Powersports Parts Related Blog Posts Yamaha Banshee Common Problems & Fixes

Read more less

Product Overview Install your freestanding bathtub with confidence using this complete drain installation kit. Includes a durable ABS plastic tailpiece and threaded adapter — everything you need to connect your freestanding tub to the floor drain. Designed for standard 1-1/2" bathtub drain connections. Freestanding tubs require precise drain alignment — this kit provides the flexibility and reliability needed for a leak-free installation that lasts for years. Key Features Complete Kit — ABS tailpiece + brass threaded adapter + gaskets Durable ABS Construction — Impact-resistant, won't rust or corrode Brass Threaded Adapter — Solid metal connection for floor drain interface Standard 1-1/2" Fit — Compatible with most freestanding bathtub drain assemblies Easy DIY Install — No special tools required beyond basic plumbing tools Compatibility Application Details Bathtub Type Freestanding bathtubs with floor drain Drain Size Standard 1-1/2 inch Floor Connection Threaded adapter compatible with standard floor drain rough-ins Specifications Specification Value Tailpiece Material ABS Plastic Adapter Material Brass Connection Size 1-1/2 inch Kit Includes Tailpiece, Adapter, Gaskets, Hardware Frequently Asked Questions Q: Will this fit my specific freestanding tub?A: This kit is designed for standard 1-1/2" drain connections found on most freestanding bathtubs. Please measure your tub's drain outlet before ordering to confirm compatibility. Q: Do I need plumber's putty or silicone for installation?A: We recommend clear silicone sealant for all drain connections (not plumber's putty — it can stain some tub materials). Apply a thin bead on all gasket surfaces. Q: Is this for new construction or retrofit?A: Both. This kit works for new freestanding tub installations and can be used when replacing an old tub with a new freestanding model, provided the floor drain rough-in aligns properly. Installation Overview Confirm floor drain rough-in position aligns with tub drain location Install threaded brass adapter into floor drain Attach ABS tailpiece to tub drain outlet Align and connect tailpiece to adapter Apply silicone sealant to all connections Test for leaks before finishing installation Related Products Browse All Home Improvement Products Related Blog Posts Freestanding Bathtub Installation Guide

Read more less

Product Overview The iFJF Adjustable Front Coil Spacer Kit delivers the most versatile lift solution for TJ, LJ, XJ, ZJ, and MJ owners who need precise ride height control. CNC-machined from solid billet aluminum, this threaded collar system lets you dial in your front lift from zero to 3.75 inches without removing the coil springs. On-vehicle adjustability means fine-tuning ride height for a level stance or compensating for different bumper/winch weights takes minutes — not hours. Key Features Infinitely Adjustable 0-3.75" Lift — Threaded billet aluminum collar design allows micro-adjustments without disassembling suspension. Dial in the exact height you need. No Spring Compressor Required — Unlike traditional spacers, this collar mounts externally and adjusts with basic hand tools. No spring removal, no compressor. CNC Billet Aluminum Construction — Machined from solid 6061-T6 aluminum. Won't deform under heavy load like plastic or rubber spacers. Anti-corrosion, anti-rust. Isolator Pad Included — Integrated polyurethane isolator prevents metal-on-metal contact and eliminates suspension noise. Anti-slip grip ring keeps everything locked. Multi-Platform Coverage — Fits Wrangler TJ (1997-2006), LJ Unlimited (2004-2006), Cherokee XJ (1984-2001), Grand Cherokee ZJ (1993-1998), and Comanche MJ (1986-1992). Compatibility Make Model Years Jeep Wrangler TJ 1997-2006 Jeep Wrangler LJ Unlimited 2004-2006 Jeep Cherokee XJ 1984-2001 Jeep Grand Cherokee ZJ 1993-1998 Jeep Comanche MJ 1986-1992 Specifications Specification Detail Material 6061-T6 Billet Aluminum Adjustment Range 0" - 3.75" (1.5" max recommended with stock arms) Isolator Polyurethane with anti-slip ring Application Front coil springs only SKU FJ-JP-JKS220 Frequently Asked Questions Q: Can I adjust height without removing the springs?A: Yes — that's the core advantage. Loosen set screws, spin the collar, re-torque. No spring compressor needed, no spring removal. Q: What's the max safe lift with stock control arms?A: Stay at 1.5" or below with factory arms. Going higher without adjustable control arms reduces caster and causes wandering steering. For 2-3.75", adjustable arms are strongly recommended. Q: Will this fix my sagging driver-side lean?A: Absolutely. Set the driver side collar slightly higher to compensate for years of single-occupant weight and spring fatigue. Q: Does this work on rear coil springs?A: No — designed for front coil springs only. Rear coil spring diameter and mount design differ on these platforms. Q: Fixed spacer vs adjustable collar — what's the real difference?A: Fixed spacers = one height, spring removal required. Our adjustable collar = infinite height control, on-vehicle adjustment, no spring removal ever. Related Products Swaybar Quick Disconnect — JK 2007-2018 Steering Stabilizer Bracket — JK 2.5" Series II Lift Kit — JK Related Blog Posts iFJF Guides — Installation & Maintenance Tips Jeep Wrangler Lift Kit Buyer's Guide

Read more less

Product Overview Achieve perfect alignment on your GM LS engine build with this CNC-machined billet alignment tool kit. Properly aligning the front cover, rear cover, and oil pan is critical for preventing oil leaks on LS engines. The factory service manual calls for special alignment tools — this kit provides them at a fraction of the dealer tool cost. If you've ever had an LS engine leak oil from the front or rear cover after a cam swap or rebuild, you know why alignment matters. The oil pan gasket interfaces with both covers — if either cover sits proud or recessed relative to the block, the oil pan gasket can't seal properly. This kit ensures everything sits flush. Key Features CNC-Machined Billet Aluminum — Precision-tooled, not cast or stamped 3-Piece Kit — Front cover, rear cover, AND oil pan alignment tools Prevents Oil Leaks — Proper alignment = proper gasket sealing Anodized Finish — Easy to clean, won't rust Essential for Any LS Build — Cam swaps, front/rear seal replacement, timing chain jobs Compatibility Engine Family Applications LS1, LS2, LS3, LS6, LS7 Corvette, Camaro, GTO, CTS-V, G8 LQ4, LQ9, LM7, LR4, L33, L59 Silverado, Sierra, Tahoe, Suburban, Avalanche LSX, LS3 Crate Aftermarket LS builds & swaps Why Alignment Matters LS engines use a unique sealing system where the front and rear covers sit against the block AND the oil pan. The oil pan gasket bridges both covers — if either cover is off by even 0.010 inch, the gasket won't seal and you'll have an oil leak. The GM factory procedure requires pressing both covers flush to the block before torquing. These tools make that process repeatable and accurate. Specifications Specification Value Material 6061-T6 Billet Aluminum Finish Clear Anodized Kit Includes 3 Alignment Tools (Front Cover, Rear Cover, Oil Pan) Manufacturing CNC Machined Frequently Asked Questions Q: Do I really need this tool, or can I align by feel?A: GM's factory service procedure requires these tools. While many DIYers "feel" the alignment, the risk of a leak is high. The covers need to be within 0.010" — you cannot reliably achieve this by hand. For the cost of this tool vs. the labor to fix a leak, it pays for itself immediately. Q: Will this work on my 5.3L LM7 truck engine?A: Yes. All Gen III and Gen IV LS-based engines use the same front and rear cover design. This kit works on everything from 4.8L to 7.0L. Q: Does this include instructions?A: The process is simple — place tool against block, press cover flush to tool face, torque cover bolts. The tool acts as a precision spacer to set the correct alignment depth. Q: Can I use this on an engine that's already in the vehicle?A: Yes, for the front cover. Rear cover alignment requires transmission removal. Oil pan alignment is accessible from underneath with the engine installed. Related Products GM LS Oil Bypass Barbell Kit — Essential LS build companion Browse All Engine Tools Related Blog Posts LS Engine Building: Common Mistakes & How to Avoid Them

Read more less

Product Overview Protect your vehicle's bumpers from parking lot dings and minor collisions with this universal aluminum bumper guard protector. The aerodynamic tail cone design adds a sporty look while absorbing impacts that would otherwise scratch, dent, or crack your factory bumper cover. Made from lightweight but durable aluminum with a polished finish, this bumper guard installs easily with the included hardware and fits most cars, SUVs, and trucks. An inexpensive investment that can save you hundreds in bumper repair costs. Key Features Lightweight Aluminum Construction — Strong protection without adding significant weight Aerodynamic Tail Cone Design — Stylish look that complements modern vehicle styling Universal Fit — Adjustable mounting brackets fit most vehicles Corrosion-Resistant — Polished aluminum finish stands up to weather and road salt Easy Bolt-On Install — Basic hand tools required, no drilling on most applications Compatibility Vehicle Type Fitment Notes Cars (Sedans, Coupes, Hatches) Universal — check bumper clearance SUVs & Crossovers Universal — adjustable brackets accommodate taller vehicles Pickup Trucks Universal — may require bracket adjustment Specifications Specification Value Material Aluminum Design Tail Cone (Tuning Style) Fitment Universal (Front or Rear) Installation Bolt-On with Included Hardware Frequently Asked Questions Q: Will this fit my car?A: This is a universal-fit bumper guard. Please measure your bumper's available mounting surface and compare to the guard dimensions before ordering. Adjustable brackets accommodate most passenger vehicles. Q: Does it require drilling?A: In most cases, no. The kit uses existing license plate holes or bracket clamps. Some applications may require minor modification. Q: Can I install this on the front AND rear?A: Yes — the design works on both front and rear bumpers. Some customers purchase two: one for front and one for rear. Q: Will it interfere with parking sensors?A: Depending on sensor placement, it may. Check your vehicle's sensor locations before installation. Some adjustment may be needed. Related Products Matching Bumper Guard — Purchase pair for front & rear Browse All Exterior Accessories Related Blog Posts Top 5 Ways to Protect Your Car's Exterior from Parking Damage

Read more less

Product Overview Unlock the true off-road potential of your Jeep Wrangler JK with the iFJF Quicker Disconnect Swaybar Link System. The factory sway bar limits wheel articulation to roughly 6-8 inches — enough for highway stability but a major handicap on rocks. This adjustable quick-disconnect system releases both sway bar links in under 30 seconds (two quick-release pins per side) for up to 30% more wheel travel. When it's time to hit pavement, reconnect just as fast — no tools, no crawling underneath, no alignment reset. Key Features 2-Pin Quick Removal — Pull two stainless steel retaining pins per side to free the sway bar. 30 seconds to disconnect, 30 seconds to reconnect. Adjustable for 2.5"-6" Lifts — Threaded heim joint design provides infinite length adjustment to maintain proper sway bar geometry at any lift height. Replace #2030/#2034 — Direct upgrade replacement for fixed-mount JKS 2030/2034 sway bar disconnects, adding the quick-release feature those systems lack. Greaseable Chromoly Heim Joints — PTFE-lined spherical rod ends with grease zerks. Silent operation, zero-slop articulation, replaceable when worn. Massive Off-Road Flex — Disconnected sway bar allows each axle to move independently, keeping all 4 tires planted on uneven terrain. Compatibility Make Model Years Lift Range Jeep Wrangler JK 2-Door 2007-2018 2.5" - 6" Jeep Wrangler JK Unlimited 2007-2018 2.5" - 6" Specifications Specification Detail Link Material DOM steel tube (powder coated) Joint Type Chromoly heim (greaseable, PTFE-lined) Pin Type Stainless steel quick-release Adjustment 2.5" - 6" lift height SKU JP-FS01-ZH Frequently Asked Questions Q: How fast is disconnect/reconnect?A: ~30 seconds per side. Pull two pins, swing link up, secure with parking strap. Reconnecting is just as fast. Q: Will these rattle on the street?A: Our PTFE-lined heim joints run silent when properly greased. A shot of grease through the zerk fitting quiets any noise instantly. Q: Do I need to disconnect both sides?A: Yes — for maximum articulation, disconnect both sides. Single-side disconnect limits flex and stresses the connected link unevenly. Q: Can I drive highway speeds disconnected?A: NO. Driving at highway speeds with sway bar disconnected is extremely dangerous — excessive body roll and unpredictable handling. Always reconnect before pavement. Q: What maintenance is required?A: Grease heim joint zerks every 3-4 trail trips. Inspect retaining pins annually. Replace heim joints when play develops (typically 2-3 years of heavy use). Related Products Swaybar Quick Disconnect — JK 2007-2018 Steering Stabilizer Bracket — JK 2.5" Series II Lift Kit — JK Related Blog Posts iFJF Guides — Installation & Maintenance Tips Jeep Wrangler Lift Kit Buyer's Guide

Read more less

Product Overview Protect your Tesla Model X's front trunk sill from scratches, scuffs, and cargo damage with this precision-engineered stainless steel sill guard. The Model X frunk sees heavy use — groceries, luggage, sports gear — and the painted sill area is extremely vulnerable to scratches. This guard provides a durable, easy-to-clean protective layer that looks like factory equipment. Laser-cut to exact Model X (2016-2025) frunk sill contours for a perfect OEM fit. The premium brushed stainless steel finish complements the Model X's modern interior aesthetic. Key Features Precision Laser-Cut — Exact fit for 2016-2025 Tesla Model X front trunk sill contours Brushed Stainless Steel — Premium finish resists scratches, fingerprints, and corrosion 3M Automotive-Grade Adhesive — Strong bond, won't damage paint if removed properly Easy DIY Install — Peel-and-stick application; install in 5 minutes Front Trunk Only — Protects the high-wear frunk loading area Compatibility Vehicle Years Tesla Model X 2016–2025 (All Trims: 75D, 100D, P100D, Long Range, Plaid) Specifications Specification Value Material Premium Stainless Steel (Brushed Finish) Installation Type 3M Adhesive (Peel & Stick) Fitment Custom Contour (Model X Specific) Quantity 1 Piece (Front Trunk Sill) Frequently Asked Questions Q: Will this fit my 2024 Model X?A: Yes. The front trunk sill dimensions have remained unchanged since the Model X launched in 2016 through the 2025 refresh. Q: Does it come with a rear trunk guard too?A: This listing is for the front trunk (frunk) sill guard only. The frunk sill is the highest-wear area since it's the primary cargo loading zone. Q: Will the adhesive damage my paint if I remove it?A: When removed correctly (using a heat gun or hair dryer to warm the adhesive), it comes off cleanly without paint damage. 3M automotive-grade adhesive is designed for this application. Q: How do I install it?A: Clean the sill surface with the included alcohol prep pad, let dry, peel the adhesive backing, align carefully, and press firmly for 60 seconds. Avoid washing the area for 24 hours after installation for maximum bond strength. Related Products Tesla Model 3 Cabin Air Filter Browse All Tesla Accessories Related Blog Posts Tesla Model X: Best Interior & Exterior Protection Accessories

Read more less

Product Overview The iFJF Gear Shift Console Organizer Tray Box and Hanging Armrest Organizer Tray Combination Storage Box for 2018-2020 Wrangler JL (Hanging Storage Box) from iFJF is a precision-engineered aftermarket upgrade designed to deliver exceptional performance, durability, and value. Crafted from premium-grade materials, this interior accessory combines practical functionality with sleek aesthetics. Designed specifically for your vehicle, it provides a seamless OEM-quality fit while enhancing comfort, convenience, and organization. Vehicle Compatibility This product is designed for the following vehicles: Please verify compatibility with your specific vehicle year, make, model, and engine configuration before purchasing. Contact our support team if you need assistance confirming fitment for your application. Note: Professional installation is recommended. Verify fitment for your specific sub-model, cab configuration, and drivetrain (2WD/4WD) before ordering. Key Features Premium-Grade Materials: High-quality ABS plastic, carbon fiber pattern, or durable nylon construction Custom Vehicle-Specific Fit: Precision-molded to match your vehicle's interior contours exactly Easy Installation: No drilling or permanent modifications — installs in minutes with basic tools Enhanced Interior Aesthetics: Upgrades the look and feel of your cabin Practical Functionality: Adds storage, organization, or protection to high-wear areas Technical Specifications Specification Details Material High-quality ABS plastic with matte finish Anti-Slip Design: Rubberized pads prevent items from sliding Easy Install: Drop-in design - no tools or modification required Compatibility Jeep Wrangler JL (2018-2020) Jeep Wrangler JLU Unlimited (2018-2020) Storage Benefits Console Tray: Organizes phone, wallet, keys, sunglasses Hanging Organizer: Additional storage for small items within arm reach Divide Space: Prevents items from getting lost in deep console Package Includes 1 × Center Console Organizer Tray 1 × Hanging Armrest Storage Box FAQ Q: Will this fit my 2021 Wrangler JL? A: This organizer is designed for 2018-2020 JL models. The 2021+ console may have different dimensions. Q: Does it interfere with charging cables? A: No, the tray design allows cable routing for phone charging. Q: Is the hanging organizer removable? A: Yes, both pieces can be easily removed when needed. Brand iFJF Condition New Warranty Contact iFJF Support for warranty details Installation Guide Clean Surface: Wipe the installation area thoroughly with isopropyl alcohol to remove all dirt and oils. Dry Fit: Test-fit the accessory before removing any adhesive backing to confirm alignment. Apply: Peel adhesive backing and carefully position the accessory. Press firmly for 30-60 seconds across the entire surface. Cure: Allow adhesive to cure for 24 hours before exposure to moisture or extreme temperatures. Recommended: Professional installation is always recommended for optimal results. Installation time varies by vehicle and experience level — typically 1-3 hours. Frequently Asked Questions Q: Does this come with installation hardware? A: Yes. The kit includes all necessary gaskets, bolts, nuts, and mounting hardware required for a complete installation. Q: Is professional tuning required after installation? A: For most applications, no tuning is required for basic operation. Contact our support team for vehicle-specific recommendations. Q: What is the warranty on this product? A: iFJF stands behind all products with comprehensive warranty coverage. Please contact our customer service team for specific warranty terms and conditions applicable to this product. Q: How long does shipping take? A: Most orders ship within 1-2 business days. Delivery times depend on your location and selected shipping method. You'll receive tracking information as soon as your order ships. Why Choose iFJF? Quality You Can Trust: Every iFJF product is manufactured to rigorous quality standards using premium materials and advanced production techniques. We don't cut corners — we engineer parts that perform and last. Direct-Fit Engineering: Our products are designed using precision CAD/CAM technology and verified against OEM specifications, ensuring a hassle-free installation that fits right the first time. Performance Proven: From daily drivers to track machines, iFJF parts deliver measurable improvements in horsepower, torque, throttle response, and overall driving experience. Exceptional Value: We offer premium-quality parts at competitive prices, giving you the best performance-per-dollar in the aftermarket industry. Dedicated Support: Our knowledgeable team is here to help — before, during, and after your purchase. Questions about fitment, installation, or performance? We've got answers. Fast, Reliable Shipping: We process and ship orders quickly from our US warehouses, so you spend less time waiting and more time enjoying your upgraded vehicle. Related Products Complete your build with these complementary iFJF products: All-Weather Floor Mats — Protect your interior with custom-fit durable floor liners Center Console Organizer Tray — Add even more storage and organization to your vehicle Seat Back Protector — Shield your seats from cargo, pets, and daily wear

Read more less

Overview Keep your communications gear exactly where you need it with the iFJF Hand-Mic Mount Base in Black. Designed for off-road enthusiasts who demand reliable radio communication this mount securely holds your Yaesu handheld microphone whether you are crawling rocks in Moab or navigating backcountry trails. The black finish adds a custom touch to your Jeep Wrangler Chevy SUV or other off-road vehicle interior. Compatibility Category Compatible Models Radio Models Yaesu FTM-300DR FTM-300 FTM-7250DR FTM-7250 FTM-400DR FT-450D Vehicle Fitment Jeep Wrangler JK/JKU/JL/JLU/YJ/TJ Chevy Off-Road SUVs FD Off-Road SUVs Mounting Location Roll Bar Dashboard Center Console Key Features Wide Radio Compatibility: Specifically designed for Yaesu FTM-series mobile radios including FTM-300DR FTM-7250DR FTM-400DR and FT-450D Secure Off-Road Grip: Heavy-duty clamping mechanism prevents microphone movement during aggressive off-road driving and vibration Premium Black Finish: Durable powder-coated finish provides corrosion resistance and adds a custom interior accent Versatile Mounting: Compatible with roll bar and dashboard mounting locations for optimal positioning Rugged Construction: Built from high-strength materials to withstand dust mud vibration and extreme temperatures Quick Microphone Access: Ergonomic design allows for fast one-hand microphone removal when you need to communicate Technical Specifications Specification Value Color Black (Powder Coated) Compatible Radios Yaesu FTM-300DR/FTM-300/FTM-7250DR/FTM-7250/FTM-400DR/FT-450D Mounting Style Roll Bar / Dashboard Clamp Material High-Strength Alloy Steel with Powder Coat Package Includes 1x Hand-Mic Mount Base Installation Choose Location: Select a mounting point on your roll bar or dashboard within easy reach of the driver seat Position Mount: Place the mount base at the desired location and align Secure Mount: Attach using appropriate hardware for your specific mounting surface (hardware not included — varies by vehicle) Insert Microphone: Slide your Yaesu handheld microphone into the mount until it clicks Test Fit: Give the microphone a gentle tug to ensure it is securely held. Test during vehicle operation to verify vibration resistance Why Choose iFJF? Off-Road Tested: iFJF products are designed by off-roaders for off-roaders — we understand the punishment your gear takes on the trail Radio-Specific Design: Unlike universal mounts this base is engineered specifically for Yaesu FTM-series microphones for a perfect fit Multiple Color Options: Also available in Red Black Blue Silver and Yellow to match your interior theme Affordable Quality: Get professional-grade mounting hardware without the premium price tag FAQ Q: Does this include the microphone?A: No this is the mount base only. The Yaesu handheld microphone is sold separately. Q: Will it fit other radio brands like Kenwood or Icom?A: This mount is specifically designed for Yaesu handheld microphones with the standard FTM-series mounting pattern. Other brands may not fit correctly. Q: What hardware do I need for installation?A: The mount base accepts standard mounting hardware. Specific bolts/screws needed depend on your mounting location. Most roll bar mounts use hose clamps or U-bolts (not included). Q: Can I install this on my Jeep grab handle?A: While designed primarily for roll bars the mount can be adapted to other locations. Ensure the mounting surface can support the microphone weight during off-road vibration. Q: Is the finish fade-resistant?A: Yes the powder-coated finish is UV-resistant and designed to maintain its color even with prolonged sun exposure. Q: Can it be used for right or left-hand operation?A: The mount is ambidextrous — it can be positioned for either right or left-hand microphone access depending on mounting orientation.

Read more less

Overview Keep your communications gear exactly where you need it with the iFJF Hand-Mic Mount Base in Blue. Designed for off-road enthusiasts who demand reliable radio communication this mount securely holds your Yaesu handheld microphone whether you are crawling rocks in Moab or navigating backcountry trails. The blue finish adds a custom touch to your Jeep Wrangler Chevy SUV or other off-road vehicle interior. Compatibility Category Compatible Models Radio Models Yaesu FTM-300DR FTM-300 FTM-7250DR FTM-7250 FTM-400DR FT-450D Vehicle Fitment Jeep Wrangler JK/JKU/JL/JLU/YJ/TJ Chevy Off-Road SUVs FD Off-Road SUVs Mounting Location Roll Bar Dashboard Center Console Key Features Wide Radio Compatibility: Specifically designed for Yaesu FTM-series mobile radios including FTM-300DR FTM-7250DR FTM-400DR and FT-450D Secure Off-Road Grip: Heavy-duty clamping mechanism prevents microphone movement during aggressive off-road driving and vibration Premium Blue Finish: Durable powder-coated finish provides corrosion resistance and adds a custom interior accent Versatile Mounting: Compatible with roll bar and dashboard mounting locations for optimal positioning Rugged Construction: Built from high-strength materials to withstand dust mud vibration and extreme temperatures Quick Microphone Access: Ergonomic design allows for fast one-hand microphone removal when you need to communicate Technical Specifications Specification Value Color Blue (Powder Coated) Compatible Radios Yaesu FTM-300DR/FTM-300/FTM-7250DR/FTM-7250/FTM-400DR/FT-450D Mounting Style Roll Bar / Dashboard Clamp Material High-Strength Alloy Steel with Powder Coat Package Includes 1x Hand-Mic Mount Base Installation Choose Location: Select a mounting point on your roll bar or dashboard within easy reach of the driver seat Position Mount: Place the mount base at the desired location and align Secure Mount: Attach using appropriate hardware for your specific mounting surface (hardware not included — varies by vehicle) Insert Microphone: Slide your Yaesu handheld microphone into the mount until it clicks Test Fit: Give the microphone a gentle tug to ensure it is securely held. Test during vehicle operation to verify vibration resistance Why Choose iFJF? Off-Road Tested: iFJF products are designed by off-roaders for off-roaders — we understand the punishment your gear takes on the trail Radio-Specific Design: Unlike universal mounts this base is engineered specifically for Yaesu FTM-series microphones for a perfect fit Multiple Color Options: Also available in Red Black Blue Silver and Yellow to match your interior theme Affordable Quality: Get professional-grade mounting hardware without the premium price tag FAQ Q: Does this include the microphone?A: No this is the mount base only. The Yaesu handheld microphone is sold separately. Q: Will it fit other radio brands like Kenwood or Icom?A: This mount is specifically designed for Yaesu handheld microphones with the standard FTM-series mounting pattern. Other brands may not fit correctly. Q: What hardware do I need for installation?A: The mount base accepts standard mounting hardware. Specific bolts/screws needed depend on your mounting location. Most roll bar mounts use hose clamps or U-bolts (not included). Q: Can I install this on my Jeep grab handle?A: While designed primarily for roll bars the mount can be adapted to other locations. Ensure the mounting surface can support the microphone weight during off-road vibration. Q: Is the finish fade-resistant?A: Yes the powder-coated finish is UV-resistant and designed to maintain its color even with prolonged sun exposure. Q: Can it be used for right or left-hand operation?A: The mount is ambidextrous — it can be positioned for either right or left-hand microphone access depending on mounting orientation.

Read more less

Overview Keep your communications gear exactly where you need it with the iFJF Hand-Mic Mount Base in Red. Designed for off-road enthusiasts who demand reliable radio communication this mount securely holds your Yaesu handheld microphone whether you are crawling rocks in Moab or navigating backcountry trails. The red finish adds a custom touch to your Jeep Wrangler Chevy SUV or other off-road vehicle interior. Compatibility Category Compatible Models Radio Models Yaesu FTM-300DR FTM-300 FTM-7250DR FTM-7250 FTM-400DR FT-450D Vehicle Fitment Jeep Wrangler JK/JKU/JL/JLU/YJ/TJ Chevy Off-Road SUVs FD Off-Road SUVs Mounting Location Roll Bar Dashboard Center Console Key Features Wide Radio Compatibility: Specifically designed for Yaesu FTM-series mobile radios including FTM-300DR FTM-7250DR FTM-400DR and FT-450D Secure Off-Road Grip: Heavy-duty clamping mechanism prevents microphone movement during aggressive off-road driving and vibration Premium Red Finish: Durable powder-coated finish provides corrosion resistance and adds a custom interior accent Versatile Mounting: Compatible with roll bar and dashboard mounting locations for optimal positioning Rugged Construction: Built from high-strength materials to withstand dust mud vibration and extreme temperatures Quick Microphone Access: Ergonomic design allows for fast one-hand microphone removal when you need to communicate Technical Specifications Specification Value Color Red (Powder Coated) Compatible Radios Yaesu FTM-300DR/FTM-300/FTM-7250DR/FTM-7250/FTM-400DR/FT-450D Mounting Style Roll Bar / Dashboard Clamp Material High-Strength Alloy Steel with Powder Coat Package Includes 1x Hand-Mic Mount Base Installation Choose Location: Select a mounting point on your roll bar or dashboard within easy reach of the driver seat Position Mount: Place the mount base at the desired location and align Secure Mount: Attach using appropriate hardware for your specific mounting surface (hardware not included — varies by vehicle) Insert Microphone: Slide your Yaesu handheld microphone into the mount until it clicks Test Fit: Give the microphone a gentle tug to ensure it is securely held. Test during vehicle operation to verify vibration resistance Why Choose iFJF? Off-Road Tested: iFJF products are designed by off-roaders for off-roaders — we understand the punishment your gear takes on the trail Radio-Specific Design: Unlike universal mounts this base is engineered specifically for Yaesu FTM-series microphones for a perfect fit Multiple Color Options: Also available in Red Black Blue Silver and Yellow to match your interior theme Affordable Quality: Get professional-grade mounting hardware without the premium price tag FAQ Q: Does this include the microphone?A: No this is the mount base only. The Yaesu handheld microphone is sold separately. Q: Will it fit other radio brands like Kenwood or Icom?A: This mount is specifically designed for Yaesu handheld microphones with the standard FTM-series mounting pattern. Other brands may not fit correctly. Q: What hardware do I need for installation?A: The mount base accepts standard mounting hardware. Specific bolts/screws needed depend on your mounting location. Most roll bar mounts use hose clamps or U-bolts (not included). Q: Can I install this on my Jeep grab handle?A: While designed primarily for roll bars the mount can be adapted to other locations. Ensure the mounting surface can support the microphone weight during off-road vibration. Q: Is the finish fade-resistant?A: Yes the powder-coated finish is UV-resistant and designed to maintain its color even with prolonged sun exposure. Q: Can it be used for right or left-hand operation?A: The mount is ambidextrous — it can be positioned for either right or left-hand microphone access depending on mounting orientation.

Read more less

Overview Keep your communications gear exactly where you need it with the iFJF Hand-Mic Mount Base in Yellow. Designed for off-road enthusiasts who demand reliable radio communication this mount securely holds your Yaesu handheld microphone whether you are crawling rocks in Moab or navigating backcountry trails. The yellow finish adds a custom touch to your Jeep Wrangler Chevy SUV or other off-road vehicle interior. Compatibility Category Compatible Models Radio Models Yaesu FTM-300DR FTM-300 FTM-7250DR FTM-7250 FTM-400DR FT-450D Vehicle Fitment Jeep Wrangler JK/JKU/JL/JLU/YJ/TJ Chevy Off-Road SUVs FD Off-Road SUVs Mounting Location Roll Bar Dashboard Center Console Key Features Wide Radio Compatibility: Specifically designed for Yaesu FTM-series mobile radios including FTM-300DR FTM-7250DR FTM-400DR and FT-450D Secure Off-Road Grip: Heavy-duty clamping mechanism prevents microphone movement during aggressive off-road driving and vibration Premium Yellow Finish: Durable powder-coated finish provides corrosion resistance and adds a custom interior accent Versatile Mounting: Compatible with roll bar and dashboard mounting locations for optimal positioning Rugged Construction: Built from high-strength materials to withstand dust mud vibration and extreme temperatures Quick Microphone Access: Ergonomic design allows for fast one-hand microphone removal when you need to communicate Technical Specifications Specification Value Color Yellow (Powder Coated) Compatible Radios Yaesu FTM-300DR/FTM-300/FTM-7250DR/FTM-7250/FTM-400DR/FT-450D Mounting Style Roll Bar / Dashboard Clamp Material High-Strength Alloy Steel with Powder Coat Package Includes 1x Hand-Mic Mount Base Installation Choose Location: Select a mounting point on your roll bar or dashboard within easy reach of the driver seat Position Mount: Place the mount base at the desired location and align Secure Mount: Attach using appropriate hardware for your specific mounting surface (hardware not included — varies by vehicle) Insert Microphone: Slide your Yaesu handheld microphone into the mount until it clicks Test Fit: Give the microphone a gentle tug to ensure it is securely held. Test during vehicle operation to verify vibration resistance Why Choose iFJF? Off-Road Tested: iFJF products are designed by off-roaders for off-roaders — we understand the punishment your gear takes on the trail Radio-Specific Design: Unlike universal mounts this base is engineered specifically for Yaesu FTM-series microphones for a perfect fit Multiple Color Options: Also available in Red Black Blue Silver and Yellow to match your interior theme Affordable Quality: Get professional-grade mounting hardware without the premium price tag FAQ Q: Does this include the microphone?A: No this is the mount base only. The Yaesu handheld microphone is sold separately. Q: Will it fit other radio brands like Kenwood or Icom?A: This mount is specifically designed for Yaesu handheld microphones with the standard FTM-series mounting pattern. Other brands may not fit correctly. Q: What hardware do I need for installation?A: The mount base accepts standard mounting hardware. Specific bolts/screws needed depend on your mounting location. Most roll bar mounts use hose clamps or U-bolts (not included). Q: Can I install this on my Jeep grab handle?A: While designed primarily for roll bars the mount can be adapted to other locations. Ensure the mounting surface can support the microphone weight during off-road vibration. Q: Is the finish fade-resistant?A: Yes the powder-coated finish is UV-resistant and designed to maintain its color even with prolonged sun exposure. Q: Can it be used for right or left-hand operation?A: The mount is ambidextrous — it can be positioned for either right or left-hand microphone access depending on mounting orientation.

Read more less

iFJF Hood Latches Lock Catch Kit for Jeep Wrangler JK JKU 2007-2018 — Black Stainless Steel Eliminate hood flutter and upgrade security on your Jeep Wrangler JK with the iFJF Hood Latches Lock Catch Kit. The factory rubber hood latches on 2007-2018 Wranglers are a well-known weak point — they stretch over time, causing the hood to flutter at highway speeds and creating a distracting, unsettling driving experience. This kit replaces the factory latches with heavy-duty black stainless steel locking catches that hold the hood firmly in place while adding a layer of anti-theft protection. Engineered for direct bolt-on fitment with no drilling or modifications required. Key Features Eliminates Hood Flutter: The factory rubber latches stretch and weaken over time, causing the hood to visibly flutter at speeds above 55 MPH. This aluminum/stainless steel latch kit locks the hood down tight, eliminating the flutter completely — even at interstate speeds and in crosswinds. Anti-Theft Locking Mechanism: Each latch incorporates a keyed lock that prevents the hood from being opened without the key. This protects your battery, aftermarket accessories, and under-hood components from theft — a common concern for Jeep owners who leave their vehicles parked with the top off. Black Stainless Steel Construction: The black powder-coated finish provides corrosion resistance and a sleek, aggressive appearance that complements any JK color scheme. Unlike raw aluminum latches that oxidize, the black coating stays looking new through mud, snow, and sun exposure. Direct Bolt-On Installation: Uses the factory mounting holes — no drilling, no cutting, no modifications required. Each latch mounts in place of the OEM rubber unit using the existing hardware locations. Most owners complete the installation in under 30 minutes with basic hand tools. Adjustable Tension: The latch mechanism allows tension adjustment to achieve the perfect fit — tight enough to eliminate flutter, but not so tight that it's difficult to close the hood. Complete Pair: Includes both driver and passenger side latches with matching keys. Both sides lock independently for full security coverage. Vehicle Compatibility Jeep Wrangler JK (2-Door): 2007-2018 Jeep Wrangler JKU (4-Door): 2007-2018 Replaces factory rubber hood latches on all JK and JKU trim levels (Sport, Sahara, Rubicon, X, Freedom, Willys, etc.) Does NOT fit: 1997-2006 TJ/LJ models, 2018+ JL/JLU models (different latch design) Why Replace Your Factory Hood Latches? Jeep equipped every JK Wrangler from the factory with simple rubber T-handle hood latches. These latches work adequately when new, but the rubber compound degrades under UV exposure and repeated stretching. Within 2-3 years — or sooner in hot climates — the latches lose tension and the hood begins to flutter. At 65 MPH on the highway, the flutter is not just annoying; it can be genuinely alarming, with the hood visibly bouncing several inches. Over time, this movement wears the hood latch striker and can damage the hood itself. Beyond the flutter, factory latches offer zero security — anyone can open your hood. This iFJF locking latch kit solves both problems in one 30-minute upgrade that pays for itself in driving comfort and peace of mind. Package Includes 1 × Driver Side Black Stainless Steel Locking Hood Latch 1 × Passenger Side Black Stainless Steel Locking Hood Latch 2 × Matching Keys All Necessary Mounting Hardware Installation Guide Frequently Asked Questions How difficult is the installation? Very straightforward. Most customers complete both sides in 20-30 minutes with basic hand tools. The kit uses the factory mounting holes — remove the old rubber latch (2 bolts per side), bolt the new locking latch in place, adjust the tension, and you're done. No drilling required. Will these rust over time? No. The black powder-coated stainless steel construction provides excellent corrosion resistance. These latches are designed to withstand mud, rain, snow, salt, and sun exposure without rusting or fading. Can I use these on a 2019 JL Wrangler? No. This kit is specifically designed for the JK platform (2007-2018). The JL uses a completely different hood latch design and mounting pattern. We recommend verifying your model year before ordering. What happens if I lose the key? Keep your spare key in a safe place. If both keys are lost, the locks can be drilled out and replaced. Contact iFJF customer support for replacement lock cylinder options. Why Choose iFJF? iFJF specializes in premium aftermarket accessories for Jeep Wrangler and off-road vehicles. Our hood latch kit is tested in real-world conditions — highway miles, trail abuse, winter salt, desert heat — to ensure it performs when you need it. Backed by a satisfaction guarantee and responsive US-based customer support. Fast Shipping: Orders ship within 1-2 business days from our US warehouse. 🔗 You May Also Like iFJF Adjustable Roll Bar Fire Extinguisher Holder for Jeep Wrangler JK 2007 iFJF Adjustable Roll Bar Fire Extinguisher Holder for Jeep Wrangler JK 2007 iFJF 91-03 Jeep 91-01 Wrangler 93-01 Cherokee 91-92 Grand Cherokee 4.0L Exh iFJF 1991-1995 2.5L Jeep Wrangler YJ L4 Exhaust Header 📖 Related Installation Guides & Articles 📝 Ball joint removal/install on 2018 ram 4500/5500 diesel. 📝 How to Install a Bluetooth Kill Switch: Anti-Theft Battery Disconnect Guide 📝 Why You Need a Bluetooth Kill Switch for Your RV or Truck

Read more less

Overview Give your Jeep Wrangler JK interior a premium motorsport-inspired upgrade with the iFJF Carbon Fiber Door Grab Handle Covers. These precision-molded ABS covers overlay your factory grab handles with a stunning carbon fiber pattern that transforms the look and feel of your cabin. Unlike stick-on overlays these covers come with screws for a permanent rattle-free mount that stays secure through every off-road adventure. Designed as exact fit for 2011-2018 JK and JKU models. Compatibility Year Make Model Doors 2011-2018 Jeep Wrangler JK 2 Door 2011-2018 Jeep Wrangler JKU Unlimited 4 Door Key Features Authentic Carbon Fiber Look: High-definition carbon fiber pattern delivers genuine motorsport aesthetic without real carbon cost Screw-Mounted Security: Unlike clip-on covers that loosen over time these include mounting screws for permanent rattle-free installation Premium ABS Construction: High-quality ABS plastic with UV-resistant coating prevents fading and cracking from sun exposure Improved Grip Feel: Textured surface provides enhanced tactile feedback and comfort during entry and exit Exact OEM Fit: Designed to match factory grab handle contours perfectly — no gaps or misalignment Complete 2-Pack Set: Includes both driver and passenger side handle covers for symmetrical interior upgrade Technical Specifications Specification Value Material ABS Plastic with UV-Resistant Coating Finish Carbon Fiber Pattern Mounting Screw-Mounted (Hardware Included) Quantity 2-Pack (Driver and Passenger Side) Compatible Years 2011-2018 Jeep Wrangler JK/JKU Installation Remove the original grab handle using a Torx T20 screwdriver Clean the handle surface to ensure proper fitment Position the new carbon fiber handle insert over the factory grab handle Align the mounting holes and insert the included screws Tighten screws evenly — do not overtighten to avoid stripping ABS material Test the handle for proper alignment tightness and comfortable grip Repeat for the passenger side handle Installation time: Approximately 15-20 minutes for both sides. Why Choose iFJF? Jeep-Specific Design: Covers engineered specifically for Wrangler JK platform — not generic universal-fit parts Secure Screw Mount: Unlike cheaper stick-on or clip-on alternatives iFJF covers stay firmly in place Premium Carbon Fiber Pattern: High-resolution finish that resists peeling fading and discoloration Factory Direct Value: iFJF manufactures its own interior accessories delivering quality at affordable price FAQ Q: Difference between screw-mounted and non-screw version?A: This version includes screws for permanent mounting providing more secure rattle-free fit compared to clip-on versions. Q: Will these fit a 2010 Jeep Wrangler JK?A: Designed for 2011-2018 interior revision. 2007-2010 models have different grab handle designs. Verify your interior trim. Q: Can I install without screws?A: While covers can be installed without screws using factory clips we strongly recommend using screws for secure rattle-free installation — especially off-road. Q: Will carbon fiber pattern fade or peel?A: UV-resistant coating prevents fading. Carbon fiber pattern is molded into ABS material — will not peel like vinyl wraps. Q: Do these replace entire grab handle?A: These are overlay covers that install over existing factory grab handles. They do not replace the handle assembly itself.

Read more less

Product Overview The iFJF Interior Door Grab Handle Inserts Cover Door Handle Trim Cover for Wrangler JK JKU 2011-2018 2 Door and 4 Door 2Pcs (Red Carbon Pattern) from iFJF is a precision-engineered aftermarket upgrade designed to deliver exceptional performance, durability, and value. Crafted from premium-grade materials, this interior accessory combines practical functionality with sleek aesthetics. Designed specifically for your vehicle, it provides a seamless OEM-quality fit while enhancing comfort, convenience, and organization. Vehicle Compatibility This product is designed for the following vehicles: Please verify compatibility with your specific vehicle year, make, model, and engine configuration before purchasing. Contact our support team if you need assistance confirming fitment for your application. Note: Professional installation is recommended. Verify fitment for your specific sub-model, cab configuration, and drivetrain (2WD/4WD) before ordering. Key Features Premium-Grade Materials: High-quality ABS plastic, carbon fiber pattern, or durable nylon construction Custom Vehicle-Specific Fit: Precision-molded to match your vehicle's interior contours exactly Easy Installation: No drilling or permanent modifications — installs in minutes with basic tools Enhanced Interior Aesthetics: Upgrades the look and feel of your cabin Practical Functionality: Adds storage, organization, or protection to high-wear areas Technical Specifications Specification Details Material High-quality ABS plastic with UV-resistant finish Exact Fit: Custom molded for Wrangler JK/JKU 2011-2018 models Easy Install: Direct replacement inserts - no modification required 2-Piece Set: Includes covers for both driver and passenger side grab handles Compatibility Jeep Wrangler JK (2011-2018) - 2 Door Jeep Wrangler JKU Unlimited (2011-2018) - 4 Door Installation Remove original grab handle screws (Torx T20) Detach original handle from mounting points Install new handle inserts in place Reinstall with original hardware Package Includes 2 × Door Grab Handle Inserts (Red Carbon Pattern) FAQ Q: Do I need special tools to install? A: You will need a Torx T20 bit to remove the original handles. Basic hand tools are sufficient. Q: Will this fit my 2007 Wrangler JK? A: No, these are designed for 2011-2018 JK/JKU models only. The handle design changed in 2011. Q: Is the carbon pattern real carbon fiber? A: This is a high-quality carbon pattern finish on durable ABS plastic for a premium look at an affordable price. Brand iFJF Condition New Warranty Contact iFJF Support for warranty details Installation Guide Clean Surface: Wipe the installation area thoroughly with isopropyl alcohol to remove all dirt and oils. Dry Fit: Test-fit the accessory before removing any adhesive backing to confirm alignment. Apply: Peel adhesive backing and carefully position the accessory. Press firmly for 30-60 seconds across the entire surface. Cure: Allow adhesive to cure for 24 hours before exposure to moisture or extreme temperatures. Recommended: Professional installation is always recommended for optimal results. Installation time varies by vehicle and experience level — typically 1-3 hours. Frequently Asked Questions Q: Does this come with installation hardware? A: Yes. The kit includes all necessary gaskets, bolts, nuts, and mounting hardware required for a complete installation. Q: Is professional tuning required after installation? A: For most applications, no tuning is required for basic operation. Contact our support team for vehicle-specific recommendations. Q: What is the warranty on this product? A: iFJF stands behind all products with comprehensive warranty coverage. Please contact our customer service team for specific warranty terms and conditions applicable to this product. Q: How long does shipping take? A: Most orders ship within 1-2 business days. Delivery times depend on your location and selected shipping method. You'll receive tracking information as soon as your order ships. Why Choose iFJF? Quality You Can Trust: Every iFJF product is manufactured to rigorous quality standards using premium materials and advanced production techniques. We don't cut corners — we engineer parts that perform and last. Direct-Fit Engineering: Our products are designed using precision CAD/CAM technology and verified against OEM specifications, ensuring a hassle-free installation that fits right the first time. Performance Proven: From daily drivers to track machines, iFJF parts deliver measurable improvements in horsepower, torque, throttle response, and overall driving experience. Exceptional Value: We offer premium-quality parts at competitive prices, giving you the best performance-per-dollar in the aftermarket industry. Dedicated Support: Our knowledgeable team is here to help — before, during, and after your purchase. Questions about fitment, installation, or performance? We've got answers. Fast, Reliable Shipping: We process and ship orders quickly from our US warehouses, so you spend less time waiting and more time enjoying your upgraded vehicle. Related Products Complete your build with these complementary iFJF products: All-Weather Floor Mats — Protect your interior with custom-fit durable floor liners Center Console Organizer Tray — Add even more storage and organization to your vehicle Seat Back Protector — Shield your seats from cargo, pets, and daily wear

Read more less

Product Overview Keep your 2016-2021 Tesla Model X trunk sills looking showroom-fresh with the iFJF Interior Front and Rear Trunk Sill Guard Protector Set. Precision laser-cut from premium 304 stainless steel, these sill plates shield your Model X's vulnerable trunk entry points from scratches, scuffs, and wear caused by loading groceries, luggage, sports gear, and daily cargo. The brushed finish perfectly complements the Model X's luxurious interior while providing a durable, easy-to-clean protective surface. Key Features Premium 304 Stainless Steel: Rust-resistant, corrosion-proof material engineered to withstand daily abuse without fading, peeling, or cracking unlike plastic alternatives. Precision Laser-Cut Fitment: CNC laser-cut to match the exact contours of 2016-2021 Tesla Model X front and rear trunk sills with no trimming required. Complete Front & Rear Set: Includes both front trunk (frunk) and rear cargo area sill protectors for full coverage where your Model X needs it most. 3M Automotive-Grade Adhesive: Pre-applied heavy-duty adhesive tape ensures a secure, bubble-free bond that withstands extreme temperatures from -40 to 200 deg F. Brushed Finish: Matches the Model X OEM interior trim aesthetics while hiding minor scratches and fingerprints better than mirror-polished alternatives. 5-Minute Peel-and-Stick Install: No drilling, no special tools required. Just clean the surface, peel the backing, and press into place. Compatibility Year Make Model Trim Position 2016-2021 Tesla Model X All Trims (60D/75D/90D/100D/P90D/P100D/Plaid) Front & Rear Trunk Sill Specifications Spec Detail Material 304 Stainless Steel Finish Brushed Satin Adhesive 3M Automotive VHB Tape Thickness 0.8mm Set Includes Front Sill Guard (1pc) + Rear Sill Guard (1pc) Part Number TSL-X-QHNB-SI Why Choose iFJF iFJF Direct is a trusted supplier of premium aftermarket replacement parts and accessories, dedicated to delivering OEM-grade quality at an accessible price. Every sill guard is laser-inspected for dimensional accuracy before shipping. Backed by our 30-day satisfaction guarantee and responsive US-based customer support. Frequently Asked Questions Q: Will this fit my 2021 Tesla Model X Refresh? A: This sill guard set is designed for 2016-2021 Tesla Model X (pre-refresh / Raven). It fits all trims including 60D, 75D, 90D, 100D, P90D, P100D, and Plaid. For 2022+ refresh models, the trunk sill dimensions are identical. Please verify with the product images before ordering. Q: How do I install these sill guards? A: Installation is straightforward: (1) Thoroughly clean the trunk sill area with the included alcohol wipe. (2) Dry completely. (3) Test-fit the guard without peeling the adhesive. (4) Peel the 3M tape backing and carefully press the guard into place, applying firm pressure for 60 seconds. (5) Allow 24 hours for the adhesive to fully cure before washing the vehicle. Q: Will the adhesive damage my Model X paint if I remove it later? A: No. The 3M automotive-grade adhesive is designed to be removable without damaging OEM paint. Use a heat gun or hair dryer to warm the adhesive, then slowly peel. Any residue can be removed with isopropyl alcohol or automotive adhesive remover. Q: Does this cover the entire trunk sill area? A: Yes, the set includes both the front trunk (frunk) sill guard and the rear cargo trunk sill guard, providing complete protection for both loading areas where scratches most commonly occur. Q: Can I use these with aftermarket trunk mats? A: Yes, the sill guards are thin (0.8mm) and sit flush with the trunk surface. They will not interfere with most aftermarket trunk mats, cargo liners, or all-weather mats. Q: How does stainless steel compare to plastic sill protectors? A: Stainless steel is far more durable than ABS plastic alternatives. It will not crack in cold weather, will not warp from heat, and will not discolor over time. The brushed finish also hides scratches much better than glossy plastic. Installation Tips For best results, install in a warm environment (above 60 deg F). Use a heat gun to warm both the sill surface and the adhesive tape before pressing down. Apply firm, even pressure across the entire guard for at least 60 seconds. Allow 24 hours of cure time before exposing to moisture or car washes. Related Products Model X Rear Trunk Sill Plate — Rear protection only Model 3 Jack Pad Adapter — Protect your undercarriage during service

Read more less

Product Overview Restore your Ford Fusion interior with the iFJF Front Interior Door Handle, precision-engineered as a direct replacement for the passenger side. When the factory door handle breaks — a common issue on 2006-2012 Fusions — this OE-spec replacement restores proper function without the dealership price tag. Manufactured from high-impact ABS polymer with exact texture and color matching, it installs in minutes with basic hand tools. Key Features Direct OE Replacement: Engineered to the exact specifications of Ford part number 6E5Z-5422600-AA with the same fit, feel, and function. High-Impact ABS Construction: Resists cracking and breakage from repeated daily use, unlike brittle budget alternatives that fail within months. Exact Color & Texture Match: Matches the OEM interior trim color and grain pattern to blend seamlessly with your existing door panel. Passenger Side (Right): Designed specifically for the front passenger door. Check our store for the driver side version (6E5Z-5422601-A) if needed. Simple DIY Install: Replaces in about 20 minutes with basic tools including a Phillips screwdriver and trim removal tool. Compatibility Year Make Model Position Notes 2006-2012 Ford Fusion Front Passenger (Right) All trims 2007-2012 Lincoln MKZ Front Passenger (Right) 2006 Lincoln Zephyr Front Passenger (Right) 2006-2011 Mercury Milan Front Passenger (Right) All trims Specifications Spec Detail Material High-Impact ABS Polymer Position Front Passenger Side (Right) OEM Part Number 6E5Z-5422600-AA Color Black (OEM Match) Installation Screw-on replacement (door panel removal required) Why Choose iFJF Broken interior door handles are one of the most common failures on the 2006-2012 Ford Fusion platform. iFJF replacements are manufactured to meet or exceed OEM material specifications, so you will not be replacing them again next year. Backed by our 30-day satisfaction guarantee. Frequently Asked Questions Q: Is this the driver or passenger side handle? A: This is the passenger side (right) front interior door handle. If you need the driver side (left), search for part number 6E5Z-5422601-A in our store. Q: How do I know if my door handle is broken? A: Common symptoms include: the handle feels loose or wobbly, the door will not open from the inside, the handle has visible cracks, or the chrome trim piece has separated from the handle body. Q: Do I need to remove the entire door panel? A: Yes. The interior door handle is mounted from behind the door panel. You will need to remove the door panel (typically 2-3 screws behind trim covers plus panel clips). A trim removal tool set is recommended to avoid damaging clips. YouTube has excellent tutorials for Fusion door panel removal. Q: Will this match the color of my interior? A: Yes, this handle is manufactured in the standard Ford black interior color used across all 2006-2012 Fusion, MKZ, Zephyr, and Milan models. The texture grain is also matched to OEM specifications. Q: Does this come with screws or mounting hardware? A: This listing is for the door handle assembly only. You will reuse your existing mounting screws. If your screws are stripped or missing, they are standard Phillips-head machine screws available at any auto parts store. Q: How long does installation take? A: Approximately 20-30 minutes for someone with basic DIY experience. First-timers should budget 45-60 minutes and watch a tutorial video beforehand. Related Products Driver Side Interior Door Handle — 6E5Z-5422601-A

Read more less

Product Overview The driver side interior door handle is the most frequently used component on your vehicle — and the most likely to fail. The iFJF Front Interior Door Handle for 2006-2012 Ford Fusion (Driver Side) provides a direct, factory-spec replacement for the broken or cracked original. Manufactured from high-impact ABS polymer with precise texture and color matching, this handle restores the factory look and feel while handling years of daily use without premature failure. Key Features Direct OE Replacement: Made to the same specifications as Ford part number 6E5Z-5422601-A with guaranteed proper fit without modification. Reinforced Stress Points: Engineered with reinforced mounting bosses at the critical connection points where factory handles commonly crack, providing enhanced durability over the original design. Driver Side (Left): Specifically for the front driver door. The driver side handle sees 5-10x more cycles than the passenger side, making quality materials essential. OEM Color & Grain Match: Black ABS with the exact texture grain pattern used on 2006-2012 Fusion, MKZ, and Milan interiors. Same-Day Shipping: In stock and ready to ship. Most orders arrive in 2-4 business days within the continental US. Compatibility Year Make Model Position Notes 2006-2012 Ford Fusion Front Driver (Left) All trims including SE/SEL/Sport 2007-2012 Lincoln MKZ Front Driver (Left) 2006 Lincoln Zephyr Front Driver (Left) 2006-2011 Mercury Milan Front Driver (Left) All trims Specifications Spec Detail Material High-Impact ABS Polymer (Reinforced) Position Front Driver Side (Left) OEM Part Number 6E5Z-5422601-A Interchange Numbers 6E5Z5422601A, 6E5Z 5422601 A Color Black (OEM Match) Installation Difficulty Intermediate (door panel removal required) Why Choose iFJF iFJF understands that the driver side door handle takes the most abuse. Our replacement handles feature reinforced mounting points that address the factory design weak spots. Combined with our 30-day money-back guarantee, you can buy with confidence. Frequently Asked Questions Q: Is this really a common failure on the Fusion? A: Yes. The 2006-2012 Ford Fusion is notorious for interior door handle failures, especially on the driver side. The original plastic mounting tabs become brittle over time from heat cycling and repeated use. This replacement uses reinforced ABS to prevent the same failure. Q: Does this come as a complete assembly? A: Yes, this is the complete interior door handle assembly including the grab handle you pull to open the door from inside. The chrome trim accent piece is pre-installed. You reuse your existing mounting screws. Q: Will this work for the rear door? A: No. This handle is specifically for the front door. The rear door handles on the Fusion have a different design and mounting pattern. Please verify which door needs replacement before ordering. Q: Can I replace just the chrome trim piece? A: If only the chrome trim accent has peeled or separated, you may be able to replace just that piece. However, in most cases the plastic handle body itself is cracked, meaning you need this complete assembly. The chrome trim is included pre-attached on this replacement. Q: How do I access the mounting screws? A: (1) Pry off the small trim cover behind the interior door handle using a flathead screwdriver or trim tool. (2) Remove the exposed Phillips screw. (3) Remove additional screws at the bottom of the door panel and behind the armrest. (4) Carefully pry the door panel clips free. The handle is then accessible from the back side of the panel. Related Products Passenger Side Interior Door Handle — 6E5Z-5422600-AA

Read more less

Product Overview The iFJF Interior Rear Trunk Sill Plate is a must-have protection upgrade for your 2016-2021 Tesla Model X. The rear cargo sill is one of the most vulnerable areas on any SUV, subject to scratches from loading groceries, luggage, strollers, pets, and sports equipment. This precision-cut 304 stainless steel guard provides a durable, rust-proof barrier that keeps your Model X paint protected while adding a premium aesthetic touch to the cargo area. Key Features Premium 304 Stainless Steel: Corrosion-resistant, non-magnetic stainless steel that will not rust, peel, or discolor even after years of heavy use and car washes. Precision Laser-Cut for Model X: CNC laser-cut to match the exact rear trunk sill contour of 2016-2021 Tesla Model X. No trimming, no gaps, no modification needed. Brushed Satin Finish: The elegant brushed finish matches the Model X OEM interior trim while effectively hiding fingerprints and minor surface scratches. 3M VHB Adhesive Backing: Pre-applied industrial-grade 3M adhesive provides a permanent, rattle-free bond rated for extreme temperatures from -40 to 200 deg F. Ultra-Thin 0.8mm Profile: Sits nearly flush with the trunk surface and will not interfere with trunk mats, cargo liners, or the automatic liftgate operation. 5-Minute DIY Install: Clean, peel, stick, press. No drilling, no special tools. Includes alcohol prep pad for surface preparation. Compatibility Year Make Model Trim Position 2016-2021 Tesla Model X 60D/75D/90D/100D/P90D/P100D/Plaid Rear Cargo Trunk Sill Specifications Spec Detail Material 304 Stainless Steel Finish Brushed Satin Thickness 0.8mm Adhesive 3M Automotive VHB (Pre-applied) Coverage Rear Trunk Sill Only Installation Peel-and-Stick (No Drilling) Why Choose iFJF Your Tesla Model X is a significant investment. Protect it with iFJF sill plates manufactured in an ISO 9001 facility using genuine 304 stainless steel — not cheap chrome-plated steel that rusts after one winter. Every plate is individually inspected for dimensional accuracy and finish quality before packaging. Frequently Asked Questions Q: Is this the same as the front and rear set? A: This listing is for the rear trunk sill plate only. If you want both the front (frunk) and rear sill protectors, check our store for the complete front and rear set. Q: Will this fit the 2022+ Model X Refresh? A: While the rear trunk sill dimensions are very similar between pre-refresh and refresh Model X, this plate was CNC-scanned on a 2016-2021 Model X. Please verify with the product images. We offer a 30-day return if it does not fit your refresh model. Q: How do I prepare the surface before installation? A: Clean the trunk sill thoroughly with isopropyl alcohol (included prep pad). Ensure the surface is completely dry and free of wax, dirt, or oils. For best results, warm both the sill surface and the adhesive tape with a hair dryer before applying, especially in temperatures below 60 deg F. Q: Will this scratch over time from loading cargo? A: The brushed finish is specifically chosen because it hides surface-level scratches very well. Unlike mirror-polished plates that show every micro-scratch, the brushed texture maintains a clean appearance even with regular cargo loading. Q: Can I remove it without damaging the paint? A: Yes. Use a heat gun or hair dryer to warm the adhesive, then slowly peel from one corner. Any remaining adhesive residue can be safely removed with 3M adhesive remover or isopropyl alcohol without harming the factory paint. Related Products Model X Front & Rear Sill Guard Set — Complete protection

Read more less