Products

Rear Trunk Inner Sill Plate Trim Cover for Tesla Model Y 2019-2021 Protect your Tesla Model Y's rear trunk area from scratches, scuffs, and daily wear with the iFJF Rear Trunk Inner Sill Plate. Precision-engineered from premium stainless steel, this trim cover provides a perfect fit for 2019-2021 Tesla Model Y vehicles while adding a sleek, modern accent to your cargo area. Whether you're loading groceries, luggage, sports gear, or work equipment, the trunk sill takes the most abuse. This durable guard absorbs impact and prevents unsightly paint damage that can diminish your Tesla's value over time. Vehicle Compatibility Make Model Year Range Body Style Tesla Model Y 2019-2021 All variants Key Features Premium Stainless Steel: Brushed finish resists corrosion, fading, and peeling — maintains a showroom look for years Precision Fit: Laser-measured and CNC-cut to match the exact contours of your Tesla Model Y's trunk sill Scratch & Scuff Protection: Creates a durable barrier between your cargo and the painted trunk sill surface Easy Installation: Pre-applied automotive-grade 3M adhesive backing — simply clean, peel, and press into place in under 10 minutes Enhanced Appearance: Adds a premium, custom look that complements your Tesla's minimalist interior design OEM+ Style: Designed to look like a factory option rather than an aftermarket add-on Technical Specifications Specification Detail SKU FJ-TSL-Y-HBNB-CK Material 304 Stainless Steel, Brushed Finish Thickness 0.8mm Adhesive 3M Automotive-Grade Double-Sided Tape (Pre-Applied) Installation Peel-and-Stick, No Drilling Required Installation Instructions Clean: Thoroughly clean the trunk sill area with isopropyl alcohol (included prep pad) to remove all wax, oil, and debris Dry Fit: Position the guard on the sill without removing the adhesive backing to verify alignment Heat (Optional): For best results in cold weather, warm the adhesive and the sill surface with a hair dryer for 30-60 seconds Peel: Remove the adhesive backing gradually, starting from one end Press: Starting from the center and working outward, apply firm, even pressure for 60 seconds across the entire surface Wait: Allow 24 hours for maximum adhesive bonding before exposing to water or car washes Why Protect Your Tesla's Trunk Sill? The trunk sill is one of the most vulnerable areas on any vehicle, and Tesla's painted sill surfaces are particularly susceptible to scratches. Every time you load or unload cargo — groceries, luggage, sports equipment, tools, or pet carriers — items drag across the painted sill. Over time, these micro-scratches accumulate, leaving your trunk opening looking worn and neglected. A stainless steel sill guard not only prevents this damage but also makes cleaning easier: simply wipe down the smooth metal surface instead of scrubbing scratched paint. Frequently Asked Questions Q: Will this fit my 2019-2021 Tesla Model Y?A: Yes. This sill protector is precision-designed for the 2019-2021 Tesla Model Y rear trunk opening. It follows the exact contour of your vehicle's trunk sill. Q: Does the adhesive damage the paint if I remove it later?A: No. The 3M automotive adhesive is designed to be removable without damaging factory paint when removed properly. Use a heat gun or hair dryer to warm the adhesive, then peel slowly. Any residue can be cleaned with adhesive remover. Q: Will the stainless steel rust or discolor over time?A: No. This guard is made from 304-grade stainless steel with a brushed finish, which is highly resistant to rust, corrosion, and discoloration — even in harsh weather conditions. Q: Can I install this in cold weather?A: For optimal adhesion, the surface temperature should be at least 60°F (15°C). In colder conditions, use a hair dryer to warm both the adhesive backing and the trunk sill surface before installation. Q: Does this interfere with the automatic trunk closing?A: No. The guard is thin (0.8mm) and follows the contour of the sill perfectly. It will not interfere with your Model Y's power liftgate operation or trunk seal.

Read more less

Rear Trunk Inner Sill Protector Trim Cover for Tesla Model 3 2017-2021 Protect your Tesla Model 3's rear trunk area from scratches, scuffs, and daily wear with the iFJF Rear Trunk Inner Sill Protector. Precision-engineered from premium stainless steel, this trim cover provides a perfect fit for 2017-2021 Tesla Model 3 vehicles while adding a sleek, modern accent to your cargo area. Whether you're loading groceries, luggage, sports gear, or work equipment, the trunk sill takes the most abuse. This durable guard absorbs impact and prevents unsightly paint damage that can diminish your Tesla's value over time. Vehicle Compatibility Make Model Year Range Body Style Tesla Model 3 2017-2021 All variants Key Features Premium Stainless Steel: Brushed finish resists corrosion, fading, and peeling — maintains a showroom look for years Precision Fit: Laser-measured and CNC-cut to match the exact contours of your Tesla Model 3's trunk sill Scratch & Scuff Protection: Creates a durable barrier between your cargo and the painted trunk sill surface Easy Installation: Pre-applied automotive-grade 3M adhesive backing — simply clean, peel, and press into place in under 10 minutes Enhanced Appearance: Adds a premium, custom look that complements your Tesla's minimalist interior design OEM+ Style: Designed to look like a factory option rather than an aftermarket add-on Technical Specifications Specification Detail SKU FJ-TSL-3-HBNB-SI Material 304 Stainless Steel, Brushed Finish Thickness 0.8mm Adhesive 3M Automotive-Grade Double-Sided Tape (Pre-Applied) Installation Peel-and-Stick, No Drilling Required Installation Instructions Clean: Thoroughly clean the trunk sill area with isopropyl alcohol (included prep pad) to remove all wax, oil, and debris Dry Fit: Position the guard on the sill without removing the adhesive backing to verify alignment Heat (Optional): For best results in cold weather, warm the adhesive and the sill surface with a hair dryer for 30-60 seconds Peel: Remove the adhesive backing gradually, starting from one end Press: Starting from the center and working outward, apply firm, even pressure for 60 seconds across the entire surface Wait: Allow 24 hours for maximum adhesive bonding before exposing to water or car washes Why Protect Your Tesla's Trunk Sill? The trunk sill is one of the most vulnerable areas on any vehicle, and Tesla's painted sill surfaces are particularly susceptible to scratches. Every time you load or unload cargo — groceries, luggage, sports equipment, tools, or pet carriers — items drag across the painted sill. Over time, these micro-scratches accumulate, leaving your trunk opening looking worn and neglected. A stainless steel sill guard not only prevents this damage but also makes cleaning easier: simply wipe down the smooth metal surface instead of scrubbing scratched paint. Frequently Asked Questions Q: Will this fit my 2017-2021 Tesla Model 3?A: Yes. This sill protector is precision-designed for the 2017-2021 Tesla Model 3 rear trunk opening. It follows the exact contour of your vehicle's trunk sill. Q: Does the adhesive damage the paint if I remove it later?A: No. The 3M automotive adhesive is designed to be removable without damaging factory paint when removed properly. Use a heat gun or hair dryer to warm the adhesive, then peel slowly. Any residue can be cleaned with adhesive remover. Q: Will the stainless steel rust or discolor over time?A: No. This guard is made from 304-grade stainless steel with a brushed finish, which is highly resistant to rust, corrosion, and discoloration — even in harsh weather conditions. Q: Can I install this in cold weather?A: For optimal adhesion, the surface temperature should be at least 60°F (15°C). In colder conditions, use a hair dryer to warm both the adhesive backing and the trunk sill surface before installation. Q: Does this interfere with the automatic trunk closing?A: No. The guard is thin (0.8mm) and follows the contour of the sill perfectly. It will not interfere with your Model 3's power liftgate operation or trunk seal.

Read more less

Rear Trunk Outer Bumper Guard Trim Cover for Tesla Model Y 2019-2021 Protect your Tesla Model Y's rear trunk area from scratches, scuffs, and daily wear with the iFJF Rear Trunk Outer Bumper Guard. Precision-engineered from premium stainless steel, this trim cover provides a perfect fit for 2019-2021 Tesla Model Y vehicles while adding a sleek, modern accent to your cargo area. Whether you're loading groceries, luggage, sports gear, or work equipment, the trunk sill takes the most abuse. This durable guard absorbs impact and prevents unsightly paint damage that can diminish your Tesla's value over time. Vehicle Compatibility Make Model Year Range Body Style Tesla Model Y 2019-2021 All variants Key Features Premium Stainless Steel: Brushed finish resists corrosion, fading, and peeling — maintains a showroom look for years Precision Fit: Laser-measured and CNC-cut to match the exact contours of your Tesla Model Y's trunk sill Scratch & Scuff Protection: Creates a durable barrier between your cargo and the painted trunk sill surface Easy Installation: Pre-applied automotive-grade 3M adhesive backing — simply clean, peel, and press into place in under 10 minutes Enhanced Appearance: Adds a premium, custom look that complements your Tesla's minimalist interior design OEM+ Style: Designed to look like a factory option rather than an aftermarket add-on Technical Specifications Specification Detail SKU FJ-TSL-Y-HBWB-CK Material 304 Stainless Steel, Brushed Finish Thickness 0.8mm Adhesive 3M Automotive-Grade Double-Sided Tape (Pre-Applied) Installation Peel-and-Stick, No Drilling Required Installation Instructions Clean: Thoroughly clean the trunk sill area with isopropyl alcohol (included prep pad) to remove all wax, oil, and debris Dry Fit: Position the guard on the sill without removing the adhesive backing to verify alignment Heat (Optional): For best results in cold weather, warm the adhesive and the sill surface with a hair dryer for 30-60 seconds Peel: Remove the adhesive backing gradually, starting from one end Press: Starting from the center and working outward, apply firm, even pressure for 60 seconds across the entire surface Wait: Allow 24 hours for maximum adhesive bonding before exposing to water or car washes Why Protect Your Tesla's Trunk Sill? The trunk sill is one of the most vulnerable areas on any vehicle, and Tesla's painted sill surfaces are particularly susceptible to scratches. Every time you load or unload cargo — groceries, luggage, sports equipment, tools, or pet carriers — items drag across the painted sill. Over time, these micro-scratches accumulate, leaving your trunk opening looking worn and neglected. A stainless steel sill guard not only prevents this damage but also makes cleaning easier: simply wipe down the smooth metal surface instead of scrubbing scratched paint. Frequently Asked Questions Q: Will this fit my 2019-2021 Tesla Model Y?A: Yes. This sill protector is precision-designed for the 2019-2021 Tesla Model Y rear trunk opening. It follows the exact contour of your vehicle's trunk sill. Q: Does the adhesive damage the paint if I remove it later?A: No. The 3M automotive adhesive is designed to be removable without damaging factory paint when removed properly. Use a heat gun or hair dryer to warm the adhesive, then peel slowly. Any residue can be cleaned with adhesive remover. Q: Will the stainless steel rust or discolor over time?A: No. This guard is made from 304-grade stainless steel with a brushed finish, which is highly resistant to rust, corrosion, and discoloration — even in harsh weather conditions. Q: Can I install this in cold weather?A: For optimal adhesion, the surface temperature should be at least 60°F (15°C). In colder conditions, use a hair dryer to warm both the adhesive backing and the trunk sill surface before installation. Q: Does this interfere with the automatic trunk closing?A: No. The guard is thin (0.8mm) and follows the contour of the sill perfectly. It will not interfere with your Model Y's power liftgate operation or trunk seal.

Read more less

Rear Trunk Outer Bumper Protector Trim Cover for Tesla Model 3 2017-2021 Protect your Tesla Model 3's rear trunk area from scratches, scuffs, and daily wear with the iFJF Rear Trunk Outer Bumper Protector. Precision-engineered from premium stainless steel, this trim cover provides a perfect fit for 2017-2021 Tesla Model 3 vehicles while adding a sleek, modern accent to your cargo area. Whether you're loading groceries, luggage, sports gear, or work equipment, the trunk sill takes the most abuse. This durable guard absorbs impact and prevents unsightly paint damage that can diminish your Tesla's value over time. Vehicle Compatibility Make Model Year Range Body Style Tesla Model 3 2017-2021 All variants Key Features Premium Stainless Steel: Brushed finish resists corrosion, fading, and peeling — maintains a showroom look for years Precision Fit: Laser-measured and CNC-cut to match the exact contours of your Tesla Model 3's trunk sill Scratch & Scuff Protection: Creates a durable barrier between your cargo and the painted trunk sill surface Easy Installation: Pre-applied automotive-grade 3M adhesive backing — simply clean, peel, and press into place in under 10 minutes Enhanced Appearance: Adds a premium, custom look that complements your Tesla's minimalist interior design OEM+ Style: Designed to look like a factory option rather than an aftermarket add-on Technical Specifications Specification Detail SKU FJ-TSL-3-HBWB-SI Material 304 Stainless Steel, Brushed Finish Thickness 0.8mm Adhesive 3M Automotive-Grade Double-Sided Tape (Pre-Applied) Installation Peel-and-Stick, No Drilling Required Installation Instructions Clean: Thoroughly clean the trunk sill area with isopropyl alcohol (included prep pad) to remove all wax, oil, and debris Dry Fit: Position the guard on the sill without removing the adhesive backing to verify alignment Heat (Optional): For best results in cold weather, warm the adhesive and the sill surface with a hair dryer for 30-60 seconds Peel: Remove the adhesive backing gradually, starting from one end Press: Starting from the center and working outward, apply firm, even pressure for 60 seconds across the entire surface Wait: Allow 24 hours for maximum adhesive bonding before exposing to water or car washes Why Protect Your Tesla's Trunk Sill? The trunk sill is one of the most vulnerable areas on any vehicle, and Tesla's painted sill surfaces are particularly susceptible to scratches. Every time you load or unload cargo — groceries, luggage, sports equipment, tools, or pet carriers — items drag across the painted sill. Over time, these micro-scratches accumulate, leaving your trunk opening looking worn and neglected. A stainless steel sill guard not only prevents this damage but also makes cleaning easier: simply wipe down the smooth metal surface instead of scrubbing scratched paint. Frequently Asked Questions Q: Will this fit my 2017-2021 Tesla Model 3?A: Yes. This sill protector is precision-designed for the 2017-2021 Tesla Model 3 rear trunk opening. It follows the exact contour of your vehicle's trunk sill. Q: Does the adhesive damage the paint if I remove it later?A: No. The 3M automotive adhesive is designed to be removable without damaging factory paint when removed properly. Use a heat gun or hair dryer to warm the adhesive, then peel slowly. Any residue can be cleaned with adhesive remover. Q: Will the stainless steel rust or discolor over time?A: No. This guard is made from 304-grade stainless steel with a brushed finish, which is highly resistant to rust, corrosion, and discoloration — even in harsh weather conditions. Q: Can I install this in cold weather?A: For optimal adhesion, the surface temperature should be at least 60°F (15°C). In colder conditions, use a hair dryer to warm both the adhesive backing and the trunk sill surface before installation. Q: Does this interfere with the automatic trunk closing?A: No. The guard is thin (0.8mm) and follows the contour of the sill perfectly. It will not interfere with your Model 3's power liftgate operation or trunk seal.

Read more less

Rear Trunk Sill Outer Bumper Guard Trim Cover for Tesla Model S 2012-2021 Protect your Tesla Model S's rear trunk area from scratches, scuffs, and daily wear with the iFJF Rear Trunk Sill Outer Bumper Guard. Precision-engineered from premium stainless steel, this trim cover provides a perfect fit for 2012-2021 Tesla Model S vehicles while adding a sleek, modern accent to your cargo area. Whether you're loading groceries, luggage, sports gear, or work equipment, the trunk sill takes the most abuse. This durable guard absorbs impact and prevents unsightly paint damage that can diminish your Tesla's value over time. Vehicle Compatibility Make Model Year Range Body Style Tesla Model S 2012-2021 All variants Key Features Premium Stainless Steel: Brushed finish resists corrosion, fading, and peeling — maintains a showroom look for years Precision Fit: Laser-measured and CNC-cut to match the exact contours of your Tesla Model S's trunk sill Scratch & Scuff Protection: Creates a durable barrier between your cargo and the painted trunk sill surface Easy Installation: Pre-applied automotive-grade 3M adhesive backing — simply clean, peel, and press into place in under 10 minutes Enhanced Appearance: Adds a premium, custom look that complements your Tesla's minimalist interior design OEM+ Style: Designed to look like a factory option rather than an aftermarket add-on Technical Specifications Specification Detail SKU FJ-TSL-S-HBWB-SI Material 304 Stainless Steel, Brushed Finish Thickness 0.8mm Adhesive 3M Automotive-Grade Double-Sided Tape (Pre-Applied) Installation Peel-and-Stick, No Drilling Required Installation Instructions Clean: Thoroughly clean the trunk sill area with isopropyl alcohol (included prep pad) to remove all wax, oil, and debris Dry Fit: Position the guard on the sill without removing the adhesive backing to verify alignment Heat (Optional): For best results in cold weather, warm the adhesive and the sill surface with a hair dryer for 30-60 seconds Peel: Remove the adhesive backing gradually, starting from one end Press: Starting from the center and working outward, apply firm, even pressure for 60 seconds across the entire surface Wait: Allow 24 hours for maximum adhesive bonding before exposing to water or car washes Why Protect Your Tesla's Trunk Sill? The trunk sill is one of the most vulnerable areas on any vehicle, and Tesla's painted sill surfaces are particularly susceptible to scratches. Every time you load or unload cargo — groceries, luggage, sports equipment, tools, or pet carriers — items drag across the painted sill. Over time, these micro-scratches accumulate, leaving your trunk opening looking worn and neglected. A stainless steel sill guard not only prevents this damage but also makes cleaning easier: simply wipe down the smooth metal surface instead of scrubbing scratched paint. Frequently Asked Questions Q: Will this fit my 2012-2021 Tesla Model S?A: Yes. This sill protector is precision-designed for the 2012-2021 Tesla Model S rear trunk opening. It follows the exact contour of your vehicle's trunk sill. Q: Does the adhesive damage the paint if I remove it later?A: No. The 3M automotive adhesive is designed to be removable without damaging factory paint when removed properly. Use a heat gun or hair dryer to warm the adhesive, then peel slowly. Any residue can be cleaned with adhesive remover. Q: Will the stainless steel rust or discolor over time?A: No. This guard is made from 304-grade stainless steel with a brushed finish, which is highly resistant to rust, corrosion, and discoloration — even in harsh weather conditions. Q: Can I install this in cold weather?A: For optimal adhesion, the surface temperature should be at least 60°F (15°C). In colder conditions, use a hair dryer to warm both the adhesive backing and the trunk sill surface before installation. Q: Does this interfere with the automatic trunk closing?A: No. The guard is thin (0.8mm) and follows the contour of the sill perfectly. It will not interfere with your Model S's power liftgate operation or trunk seal.

Read more less

Rear Trunk Sill Plate Interior & Exterior Set Trim Cover for Tesla Model 3 2017-2021 Protect your Tesla Model 3's rear trunk area from scratches, scuffs, and daily wear with the iFJF Rear Trunk Sill Plate Interior & Exterior Set. Precision-engineered from premium stainless steel, this trim cover provides a perfect fit for 2017-2021 Tesla Model 3 vehicles while adding a sleek, modern accent to your cargo area. Whether you're loading groceries, luggage, sports gear, or work equipment, the trunk sill takes the most abuse. This durable guard absorbs impact and prevents unsightly paint damage that can diminish your Tesla's value over time. Vehicle Compatibility Make Model Year Range Body Style Tesla Model 3 2017-2021 All variants Key Features Premium Stainless Steel: Brushed finish resists corrosion, fading, and peeling — maintains a showroom look for years Precision Fit: Laser-measured and CNC-cut to match the exact contours of your Tesla Model 3's trunk sill Scratch & Scuff Protection: Creates a durable barrier between your cargo and the painted trunk sill surface Easy Installation: Pre-applied automotive-grade 3M adhesive backing — simply clean, peel, and press into place in under 10 minutes Enhanced Appearance: Adds a premium, custom look that complements your Tesla's minimalist interior design OEM+ Style: Designed to look like a factory option rather than an aftermarket add-on Technical Specifications Specification Detail SKU FJ-TSL-3-HNWB-SI Material 304 Stainless Steel, Brushed Finish Thickness 0.8mm Adhesive 3M Automotive-Grade Double-Sided Tape (Pre-Applied) Installation Peel-and-Stick, No Drilling Required Installation Instructions Clean: Thoroughly clean the trunk sill area with isopropyl alcohol (included prep pad) to remove all wax, oil, and debris Dry Fit: Position the guard on the sill without removing the adhesive backing to verify alignment Heat (Optional): For best results in cold weather, warm the adhesive and the sill surface with a hair dryer for 30-60 seconds Peel: Remove the adhesive backing gradually, starting from one end Press: Starting from the center and working outward, apply firm, even pressure for 60 seconds across the entire surface Wait: Allow 24 hours for maximum adhesive bonding before exposing to water or car washes Why Protect Your Tesla's Trunk Sill? The trunk sill is one of the most vulnerable areas on any vehicle, and Tesla's painted sill surfaces are particularly susceptible to scratches. Every time you load or unload cargo — groceries, luggage, sports equipment, tools, or pet carriers — items drag across the painted sill. Over time, these micro-scratches accumulate, leaving your trunk opening looking worn and neglected. A stainless steel sill guard not only prevents this damage but also makes cleaning easier: simply wipe down the smooth metal surface instead of scrubbing scratched paint. Frequently Asked Questions Q: Will this fit my 2017-2021 Tesla Model 3?A: Yes. This sill protector is precision-designed for the 2017-2021 Tesla Model 3 rear trunk opening. It follows the exact contour of your vehicle's trunk sill. Q: Does the adhesive damage the paint if I remove it later?A: No. The 3M automotive adhesive is designed to be removable without damaging factory paint when removed properly. Use a heat gun or hair dryer to warm the adhesive, then peel slowly. Any residue can be cleaned with adhesive remover. Q: Will the stainless steel rust or discolor over time?A: No. This guard is made from 304-grade stainless steel with a brushed finish, which is highly resistant to rust, corrosion, and discoloration — even in harsh weather conditions. Q: Can I install this in cold weather?A: For optimal adhesion, the surface temperature should be at least 60°F (15°C). In colder conditions, use a hair dryer to warm both the adhesive backing and the trunk sill surface before installation. Q: Does this interfere with the automatic trunk closing?A: No. The guard is thin (0.8mm) and follows the contour of the sill perfectly. It will not interfere with your Model 3's power liftgate operation or trunk seal.

Read more less

Replacement Engine Cover for RedMax EBZ8500 EBZ7500 EBZ6500 Backpack Blowers Restore your RedMax backpack leaf blower to full working condition with the iFJF Replacement Engine Cover. This OEM-spec replacement part (#576561701) fits RedMax EBZ8500, EBZ7500, and EBZ6500 backpack blower models. A cracked, broken, or missing engine cover exposes your blower's engine to debris, dust, and moisture — leading to premature wear, reduced performance, and potential engine damage. This durable red replacement cover restores factory-level protection, keeping your commercial or residential blower running strong through every season. Compatibility Brand Model Part Number RedMax EBZ8500 Backpack Blower 576561701 RedMax EBZ7500 Backpack Blower 576561701 RedMax EBZ6500 Backpack Blower 576561701 Key Features OEM Specification: Manufactured to match RedMax factory dimensions, mounting points, and airflow requirements Durable Construction: High-impact polymer resists cracking from vibration and accidental impacts UV-Stabilized Color: Red finish resists fading from prolonged sun exposure during commercial use Complete Engine Protection: Shields the engine from dust, debris, moisture, and incidental contact Direct Bolt-On Fit: Uses existing factory mounting points — no modification required Commercial Grade: Built to withstand the daily demands of landscaping professionals Technical Specifications Specification Detail SKU FJ-HZ-ZK-576561701 Replaces OEM 576561701 Material High-Impact Injection-Molded Polymer Color RedMax Red Compatible Models EBZ8500, EBZ7500, EBZ6500 Signs Your Engine Cover Needs Replacement Visible cracks or splits in the existing cover Missing or broken mounting tabs causing the cover to rattle during operation Excessive engine noise due to the cover not sealing properly Debris accumulation around the engine area Cover missing entirely — exposing the engine to the elements Installation Replacing the engine cover is straightforward and requires only basic hand tools. Remove the old cover by unscrewing the mounting bolts, clean the mounting surface, align the new cover with the mounting points, and tighten the bolts evenly. No specialized tools or mechanical expertise required — most users can complete the job in under 15 minutes. Frequently Asked Questions Q: Will this cover fit my RedMax EBZ8500?A: Yes. This engine cover is designed for RedMax EBZ8500, EBZ7500, and EBZ6500 backpack blower models that use OEM part number 576561701. Q: Is this an OEM RedMax part?A: This is a high-quality aftermarket replacement manufactured to OEM specifications. It fits and functions identically to the RedMax original at a more affordable price point. Q: Does the cover come with mounting hardware?A: The cover itself includes the mounting points. You can reuse your existing bolts. If your original bolts are missing or damaged, standard metric fasteners from any hardware store will work. Q: How do I confirm this is the right part for my blower?A: Locate the model number on your blower (usually on a sticker on the frame or engine). If it reads EBZ8500, EBZ7500, or EBZ6500, this cover is compatible. You can also verify by checking your existing cover for part number 576561701. Q: Is this cover suitable for commercial landscaping use?A: Absolutely. The high-impact polymer construction is specifically designed to endure the rigorous daily demands of commercial landscaping operations.

Read more less

Refrigerator Button Panel Circuit Board 3850964036 — RV Refrigerator Control Board The iFJF Refrigerator Button Panel Circuit Board (3850964036) is a direct replacement control board for Dometic and Norcold 2-way RV refrigerators. This circuit board replaces the common failure-prone part #3850964010 and restores full button functionality to your RV refrigerator's control panel. If your fridge buttons have become unresponsive, intermittent, or stopped working entirely, this replacement board provides a cost-effective fix that gets your RV refrigerator back to reliable operation — without the expense of replacing the entire cooling unit. Compatibility Brand Model Series Type Dometic RM1350, RM3762, RM3962 2-Way (LP Gas / Electric) Norcold Compatible 2-Way Models 2-Way (LP Gas / Electric) Key Features Direct Replacement: Replaces OEM part number 3850964010 — same dimensions, same connector, same functionality Restores Full Control: Brings back all button functions — power on/off, temperature adjustment, mode selection (LP Gas / Electric / Auto) Enhanced Reliability: Upgraded circuit traces and components for improved durability over the original design Plug-and-Play Installation: No soldering or wiring modifications required — disconnect old board, connect new one Includes Faceplate Overlay: Comes with a new button membrane overlay to replace worn, faded, or cracked originals Mechanical Enhancement: Improves the overall operation of the refrigerator's control system Technical Specifications Specification Detail SKU FJ-JP-X-DLB04-CK Replaces OEM Part 3850964010, 3850964036 Compatible Models RM1350, RM3762, RM3962 Refrigerator Type 2-Way Absorption (LP Gas / 120V Electric) Installation Plug-and-Play, No Soldering Required Symptoms of a Failing Control Board Buttons require multiple presses to respond Display shows error codes or flickers intermittently Refrigerator won't switch between gas and electric modes Temperature adjustment buttons are unresponsive Control panel is completely dead (no lights, no response) Refrigerator randomly shuts off or changes modes Installation Guide Disconnect Power: Unplug the RV from shore power AND disconnect the 12V battery. Turn off LP gas at the tank. Access Control Panel: Remove the refrigerator's front control panel cover (typically held by clips or screws at the top edge) Disconnect Old Board: Carefully unplug the wiring harness connector from the old circuit board Remove Old Board: Unscrew or unclip the old board from its mounting location Install New Board: Mount the new 3850964036 board in the same position and reconnect the wiring harness Apply Faceplate Overlay: Clean the button area, align the new overlay, and press firmly into place Test: Reconnect power and test all button functions before reinstalling the cover panel Frequently Asked Questions Q: Is this board compatible with my Dometic RM1350 refrigerator?A: Yes. The 3850964036 board is a direct replacement for Dometic RM1350, RM3762, and RM3962 2-way refrigerators that use the 3850964010 control board. Q: Do I need any special tools to install this?A: Only basic hand tools are needed — typically a Phillips screwdriver to access the control panel. No soldering or electrical expertise is required. Q: Will this fix my refrigerator if the cooling unit is bad?A: This board only addresses control panel and button issues. If your refrigerator's cooling unit (absorption system) has failed, the control board will not resolve cooling problems. Check for ammonia smell or yellow residue — signs of cooling unit failure. Q: How do I know if I need the 3850964010 or 3850964036 board?A: Both part numbers are compatible. The 3850964036 is the updated version. If your original board is labeled 3850964010, this replacement board is a direct, improved substitute. Q: Does this come with installation instructions?A: Yes. Basic installation guidance is included. The process is straightforward for anyone comfortable with basic RV DIY repairs — typically 20-30 minutes.

Read more less

Symmons T-35A-B Hot & Cold Seat Removal Tool — Plumbing Repair Tool The iFJF Removal Tool for Symmons T-35A-B is a specialized plumbing tool designed for the precise removal and installation of hot and cold water seats in Symmons shower and tub valves. This tool is engineered to fit the TA-4, TA-10, and TA-25A/B series Symmons valve seats, making it an essential addition to any professional plumber's toolkit or a must-have for DIY homeowners maintaining their Symmons plumbing fixtures. Avoid stripped seats, damaged valve bodies, and costly professional repair calls with this purpose-built removal tool. Compatibility Brand Valve Series Seat Types Symmons T-35A-B Hot & Cold Water Seats Symmons TA-4, TA-10 Standard Valve Seats Symmons TA-25A, TA-25B Diverter & Mixer Valve Seats Key Features Precision Fit: Machined to exact tolerances for Symmons T-35A-B, TA-4, TA-10, TA-25A, and TA-25B valve seats Dual-Ended Design: Works on both hot and cold water seats — no need for multiple tools Hardened Steel Construction: Built from high-carbon tool steel that resists rounding and wear Secure Grip: Prevents stripping or damaging the brass seat during removal Ergonomic Handle: Provides excellent leverage for breaking free seats that have been in place for decades Professional Grade: Used by plumbing professionals for reliable, damage-free seat extraction Technical Specifications Specification Detail SKU FJ-TOOL24-02 Material Hardened Carbon Tool Steel Compatible Seats T-35A-B, TA-4, TA-10, TA-25A, TA-25B Application Symmons Shower & Tub Valve Seat Removal/Installation When to Replace Symmons Valve Seats Persistent Drips: If your Symmons shower or tub faucet continues to drip after replacing the washer or cartridge, the valve seat is likely worn or corroded Uneven Water Flow: Reduced or inconsistent water pressure from the showerhead or tub spout Visible Damage: Pitting, scoring, or corrosion visible on the seat surface when inspected with a flashlight Age: Symmons valves are known for longevity — but seats in valves 15+ years old often benefit from replacement Leaking from Handle: Water leaking from around the valve handle stem can indicate a damaged seat Usage Instructions Turn Off Water Supply: Shut off the main water supply to the shower or tub valve Remove Handle & Trim: Take off the handle, escutcheon plate, and valve cartridge/stem to access the seat Select Correct End: Choose the end of the tool that matches your seat size (hot or cold) Engage Tool: Insert the tool firmly into the seat, ensuring full engagement with the seat's internal profile Turn Counterclockwise: Apply steady, even pressure to unscrew the old seat. For stubborn seats, a brief tap with a hammer on the tool handle can help break corrosion Install New Seat: Thread the new seat in by hand, then use the tool to snug it — do not overtighten Reassemble Valve: Reinstall the cartridge, trim, and handle. Turn water back on and test for leaks Frequently Asked Questions Q: Will this tool work on my Symmons shower valve?A: This tool is designed for Symmons T-35A-B series valves and compatible TA-4, TA-10, TA-25A, and TA-25B seat types. If your Symmons valve uses these seat types, this tool is the correct fit. Q: Can I use this tool to install new seats as well?A: Yes. The tool works for both removal and installation. Use it to snug the new seat into place — but be careful not to overtighten, which can damage the brass threads. Q: What if the seat is stuck and won't budge?A: For heavily corroded or seized seats, try applying penetrating oil (such as PB Blaster or Kroil) and letting it soak for 15-30 minutes. A gentle tap on the tool handle with a hammer can also help break the corrosion bond. If the seat remains stuck, consult a professional plumber to avoid damaging the valve body. Q: Is this tool compatible with non-Symmons valves?A: This tool is specifically designed for Symmons valve seats. Using it on other brands may result in a poor fit and potential damage to the seat or tool. Q: Do you carry replacement Symmons seats?A: This listing is for the removal tool only. We recommend sourcing genuine Symmons replacement seats (TA-4, TA-10, TA-25A/B) from your local plumbing supply or directly from Symmons.

Read more less

Product Overview The iFJF Circuit Board is a premium aftermarket replacement part engineered for precision fit and lasting durability. Designed to match or exceed OEM specifications, this circuit board delivers reliable performance for your vehicle. Replaces OEM Part Numbers: CTBD50, FM350, FM352, FM500, FM502 Brand: iFJF Condition: Brand New, Aftermarket Compatibility & Fitment Vehicle Make Model Year Range Engine This product fits multiple applications. Please verify fitment with your vehicle specifications. Technical Specifications Specification Detail Part Type Circuit Board Brand iFJF Replaces OEM CTBD50, FM350, FM352, FM500 Condition New Aftermarket Material High-Grade Steel / Aluminum / Composite Finish Corrosion-Resistant Coating Fitment Type Direct Replacement Key Features & Benefits Precision Engineering: Manufactured to exact tolerances for seamless fit and function OEM-Equivalent Performance: Meets or exceeds factory specifications for reliable operation Durable Construction: Built with high-quality materials to withstand demanding conditions Easy Installation: Direct bolt-on replacement — no modifications required Corrosion Resistant: Protective coating prevents rust and extends service life Cost-Effective: Premium quality at a fraction of OEM dealer pricing Thoroughly Tested: Each unit undergoes quality inspection before shipment Installation Guide Verify this circuit board matches your vehicle make, model, and year Gather necessary tools: socket set, wrenches, torque wrench, safety equipment Park vehicle on level surface and engage parking brake Remove the old/damaged component carefully, noting orientation Clean mounting surface and inspect surrounding components for wear Install the new iFJF Circuit Board in the same orientation Torque all fasteners to manufacturer specifications Test operation before returning vehicle to service ⚠️ Professional installation recommended for safety-critical components. Always consult your vehicle service manual for torque specs. Frequently Asked Questions Q: Is this circuit board compatible with my vehicle? A: Please verify your vehicle's make, model, year, and engine against our compatibility table above. For specific fitment questions, contact us with your VIN number. Q: Does this replace OEM part numbers CTBD50, FM350, FM352? A: Yes, this circuit board is designed as a direct replacement for CTBD50, FM350, FM352. It meets or exceeds factory specifications. Q: What's included in the package? A: Each package includes the Circuit Board assembly as shown. Installation hardware is included where applicable. Please check product images for complete contents. Q: Do you offer a warranty? A: Yes! All iFJF products come with a satisfaction guarantee. If you experience any issues, contact our customer service team for a replacement or refund. Q: How long does shipping take? A: Orders are processed within 1-2 business days. Standard shipping to the contiguous US takes 3-7 business days. Expedited options available at checkout. Related Products Looking for more? Check out these related products from iFJF: iFJF RV Circuit Board Kit Replacement for 3316995900 Refrigerator Cont Helpful Articles iFJF Blog — Installation Tips, Maintenance Guides & Product Updates How to Choose the Right Aftermarket Parts for Your Vehicle

Read more less

Product Overview The iFJF Kit is a premium aftermarket replacement part engineered for precision fit and lasting durability. Designed to match or exceed OEM specifications, this kit delivers reliable performance for your vehicle. Compatible Vehicles: Zurn Replaces OEM Part Numbers: RK34-975X Brand: iFJF Condition: Brand New, Aftermarket Compatibility & Fitment Vehicle Make Model Year Range Engine Zurn - - - Technical Specifications Specification Detail Part Type Kit Brand iFJF Replaces OEM RK34-975X Condition New Aftermarket Material High-Grade Steel / Aluminum / Composite Finish Corrosion-Resistant Coating Fitment Type Direct Replacement Key Features & Benefits Precision Engineering: Manufactured to exact tolerances for seamless fit and function OEM-Equivalent Performance: Meets or exceeds factory specifications for reliable operation Durable Construction: Built with high-quality materials to withstand demanding conditions Easy Installation: Direct bolt-on replacement — no modifications required Corrosion Resistant: Protective coating prevents rust and extends service life Cost-Effective: Premium quality at a fraction of OEM dealer pricing Thoroughly Tested: Each unit undergoes quality inspection before shipment Installation Guide Verify this kit matches your vehicle make, model, and year Gather necessary tools: socket set, wrenches, torque wrench, safety equipment Park vehicle on level surface and engage parking brake Remove the old/damaged component carefully, noting orientation Clean mounting surface and inspect surrounding components for wear Install the new iFJF Kit in the same orientation Torque all fasteners to manufacturer specifications Test operation before returning vehicle to service ⚠️ Professional installation recommended for safety-critical components. Always consult your vehicle service manual for torque specs. Frequently Asked Questions Q: Is this kit compatible with my vehicle? A: Please verify your vehicle's make, model, year, and engine against our compatibility table above. For specific fitment questions, contact us with your VIN number. Q: Does this replace OEM part numbers RK34-975X? A: Yes, this kit is designed as a direct replacement for RK34-975X. It meets or exceeds factory specifications. Q: What's included in the package? A: Each package includes the Kit assembly as shown. Installation hardware is included where applicable. Please check product images for complete contents. Q: Do you offer a warranty? A: Yes! All iFJF products come with a satisfaction guarantee. If you experience any issues, contact our customer service team for a replacement or refund. Q: How long does shipping take? A: Orders are processed within 1-2 business days. Standard shipping to the contiguous US takes 3-7 business days. Expedited options available at checkout. Related Products Looking for more? Check out these related products from iFJF: Browse our full product catalog for more great deals Helpful Articles iFJF Blog — Installation Tips, Maintenance Guides & Product Updates How to Choose the Right Aftermarket Parts for Your Vehicle

Read more less

Stop Hard Top Leaks & Wind Noise — iFJF Roof Flow Seal Strip If your Jeep Wrangler hard top is letting in water, dust, or excessive wind noise on the highway, the iFJF Roof Flow Seal Strip is the fix. Designed specifically for the Wrangler JK and JL hard top roofline, this high-density EPDM rubber weatherstrip seals the gap between the windshield frame and hard top — the #1 leak point on Wrangler hard tops. Stop water dripping onto your dash and enjoy a quieter cabin in one 15-minute install. Key Features Premium EPDM Rubber — Unlike cheap foam strips that compress and fail within months, our seal strip uses automotive-grade EPDM rubber with high elasticity and memory rebound. It maintains its shape through repeated hard top on/off cycles. Waterproof & Dustproof Seal — The precision profile creates a tight compression seal between the windshield header and hard top leading edge, blocking rainwater, car wash spray, and trail dust from entering the cabin. Highway Wind Noise Reduction — Eliminates the whistle and buffeting caused by air rushing through the windshield-to-hard top gap. Noticeably quieter cabin at highway speeds (55–75 mph). UV & Weather-Resistant — Formulated to withstand extreme sun exposure, freezing winters, and heat cycling without cracking, shrinking, or losing elasticity. Built for year-round performance. Easy Peel-and-Stick Install — Pre-cut to length with automotive-grade 3M adhesive backing. Clean the surface, peel, stick, press — no special tools or mechanical skills required. Installs in approximately 15 minutes. Compatibility Model Years Body Style Top Type Wrangler JK / JKU 2007 – 2018 2-Door & 4-Door Hard Top Only Wrangler JL / JLU 2018 – 2022 2-Door & 4-Door Hard Top Only ⚠️ Not compatible with soft tops or Sky One-Touch power top. Hard top (Freedom Panel or one-piece) required. FAQ Q: How do I install the Roof Flow Seal Strip? A: Installation is straightforward — clean the windshield frame top surface with the included alcohol prep pad, let it dry completely, peel the adhesive backing, align the strip along the windshield header edge, and press firmly along the entire length. For best adhesion, install when the temperature is above 50°F (10°C) and avoid getting the surface wet for 24 hours after install. Q: Does this affect hard top removal or reinstallation? A: No. The seal strip sits on the windshield frame, not the hard top itself. You can remove and reinstall your hard top as normal — the strip stays in place and simply compresses when the hard top is clamped down. It will not interfere with Freedom Panel removal either. Q: How long does the seal strip last? A: With proper installation, the EPDM rubber and 3M adhesive are rated for 3–5+ years of outdoor exposure. Extreme climates (desert heat, salted winter roads) may shorten lifespan slightly. Inspect annually for any lifting or wear. Q: How is this different from other Wrangler seal strips? A: Many budget alternatives use open-cell foam that absorbs water and collapses over time. Our EPDM rubber is closed-cell, meaning it won't absorb moisture or lose its compression rebound after repeated clamping cycles. The adhesive is genuine 3M automotive-grade tape, not generic double-sided tape that peels off in summer heat. Installation Tips Surface Prep is Critical: Use the included alcohol wipe to thoroughly clean the windshield frame surface. Any dirt, wax, or silicone residue will compromise adhesion. Temperature Matters: Install in 50–90°F (10–32°C) for optimal adhesive bonding. If installing in colder weather, warm the surface with a heat gun or hair dryer first. Dry Fit First: Before peeling the backing, lay the strip in position to confirm alignment and length. Trim if necessary with sharp scissors. Press Firmly: After sticking, apply firm, even pressure along the entire length for 30–60 seconds. A roller tool (or the back of a spoon) helps ensure full contact. Cure Time: Allow the adhesive to cure for at least 24 hours before exposing to water or highway speeds for maximum bond strength. Package Includes: 1 × Roof Flow Seal Strip, 1 × Alcohol Prep Pad, Installation Guide Brand: iFJF | SKU: JP-SEAL11-CK | Material: EPDM Rubber with 3M Adhesive Backing

Read more less

Red Sport-Style Jeep Wrangler Roof Cargo Net — Sunshade & Storage 2-in-1 Give your Jeep Wrangler a bold, functional upgrade with the iFJF Red Roof Hammock Cargo Net. This vibrant red mesh stretches across the interior roof, creating a versatile overhead storage zone while adding a sporty custom look. Whether you're hauling trail gear, stashing jackets, or keeping valuables out of sight, this roof net keeps everything secured and accessible. The aggressive red colorway stands out against your interior, letting your Wrangler's personality shine through. Key Features Striking Red Design: Vivid red mesh fabric delivers a head-turning sport aesthetic that complements any Jeep Wrangler interior. The bold color is easy to spot and adds instant personality to your cabin. High-Elasticity Premium Mesh: Constructed from high-tensile elastic netting that expands to hold gear snugly. The 4-way stretch fabric conforms to your cargo, preventing shifting and rattling even on rough trails. Full Jeep Wrangler Compatibility: Engineered to fit YJ (1987-1995), TJ/LJ (1997-2006), JK/JKU (2007-2018), JL/JLU (2018-present), and Gladiator JT (2020-present) — both 2-door and 4-door models. Quick 5-Minute Installation: No drilling, no tools required. Simply attach the adjustable straps to your roll bars or roof frame poles. Strong suction cup anchors keep the net firmly in place without damaging your interior. Off-Road & Overlanding Essential: Keeps jackets, blankets, first-aid kits, tow straps, and trail snacks within arm's reach. Frees up floor space and keeps the cabin organized on long adventures. Theft-Deterrent Overhead Storage: Stash sunglasses, wallets, phones, and other small valuables overhead — out of sight from prying eyes when parked with the top off. Compatibility Model Years Body Style Wrangler YJ 1987–1995 2-Door Wrangler TJ / LJ 1997–2006 2-Door / 4-Door (LJ Unlimited) Wrangler JK / JKU 2007–2018 2-Door / 4-Door Wrangler JL / JLU 2018–Present 2-Door / 4-Door Gladiator JT 2020–Present 4-Door Pickup Specifications Material: High-elasticity polyester mesh with reinforced binding Color: Red Weight Capacity: Up to 220 lbs (evenly distributed) Installation: Straps + suction cup anchor system SKU: FJ-JP-NET08-RD Frequently Asked Questions Q: Will this fit my 4-door JKU with a hardtop? A: Yes! The roof cargo net mounts to your interior roll bars, so it works perfectly with both hardtop and soft top configurations. The mesh sits below the roof line and won't interfere with your top. Q: Can I use this as both a hammock and a cargo net at the same time? A: While primarily designed as a cargo net for gear storage, the elastic mesh provides a comfortable resting surface when parked. Many Wrangler owners use it to lounge and stargaze after hitting camp — just make sure the net is properly secured before putting weight on it. Q: Does it block rearview mirror visibility? A: No. The net sits above the windshield line and behind the front seats, so your rearview mirror visibility remains unaffected. It's designed to occupy the rear passenger roof area. Q: Will the suction cups hold on rough off-road trails? A: Yes. The suction cups are industrial-grade and paired with adjustable nylon straps. When properly tensioned, they handle washboard roads, rock crawling, and highway speeds without slipping. Q: Is the red color UV-resistant? A: The polyester mesh is treated with UV inhibitors to resist fading. With a top on, it's shielded from direct sunlight. If you run topless regularly, we recommend occasional treatment with a UV protectant spray to keep the red vibrant for years.

Read more less

Product Overview The iFJF Mount is a premium aftermarket replacement part engineered for precision fit and lasting durability. Designed to match or exceed OEM specifications, this mount delivers reliable performance for your vehicle. Compatible Vehicles: Polaris RZR Brand: iFJF Condition: Brand New, Aftermarket Compatibility & Fitment Vehicle Make Model Year Range Engine Polaris RZR - - Technical Specifications Specification Detail Part Type Mount Brand iFJF Condition New Aftermarket Material High-Grade Steel / Aluminum / Composite Finish Corrosion-Resistant Coating Fitment Type Direct Replacement Key Features & Benefits Precision Engineering: Manufactured to exact tolerances for seamless fit and function OEM-Equivalent Performance: Meets or exceeds factory specifications for reliable operation Durable Construction: Built with high-quality materials to withstand demanding conditions Easy Installation: Direct bolt-on replacement — no modifications required Corrosion Resistant: Protective coating prevents rust and extends service life Cost-Effective: Premium quality at a fraction of OEM dealer pricing Thoroughly Tested: Each unit undergoes quality inspection before shipment Installation Guide Verify this mount matches your vehicle make, model, and year Gather necessary tools: socket set, wrenches, torque wrench, safety equipment Park vehicle on level surface and engage parking brake Remove the old/damaged component carefully, noting orientation Clean mounting surface and inspect surrounding components for wear Install the new iFJF Mount in the same orientation Torque all fasteners to manufacturer specifications Test operation before returning vehicle to service ⚠️ Professional installation recommended for safety-critical components. Always consult your vehicle service manual for torque specs. Frequently Asked Questions Q: Is this mount compatible with my vehicle? A: Please verify your vehicle's make, model, year, and engine against our compatibility table above. For specific fitment questions, contact us with your VIN number. Q: Does this replace OEM part numbers the original? A: Yes, this mount is designed as a direct replacement forthe OEM component. It meets or exceeds factory specifications. Q: What's included in the package? A: Each package includes the Mount assembly as shown. Installation hardware is included where applicable. Please check product images for complete contents. Q: Do you offer a warranty? A: Yes! All iFJF products come with a satisfaction guarantee. If you experience any issues, contact our customer service team for a replacement or refund. Q: How long does shipping take? A: Orders are processed within 1-2 business days. Standard shipping to the contiguous US takes 3-7 business days. Expedited options available at checkout. Related Products Looking for more? Check out these related products from iFJF: Browse our full product catalog for more great deals Helpful Articles iFJF Blog — Installation Tips, Maintenance Guides & Product Updates How to Choose the Right Aftermarket Parts for Your Vehicle

Read more less

Product Overview The iFJF Faucet Parts is a premium aftermarket replacement part engineered for precision fit and lasting durability. Designed to match or exceed OEM specifications, this faucet parts delivers reliable performance for your vehicle. Compatible Vehicles: Delta Replaces OEM Part Numbers: RP25513 Brand: iFJF Condition: Brand New, Aftermarket Compatibility & Fitment Vehicle Make Model Year Range Engine Delta - - - Technical Specifications Specification Detail Part Type Faucet Parts Brand iFJF Replaces OEM RP25513 Condition New Aftermarket Material High-Grade Steel / Aluminum / Composite Finish Corrosion-Resistant Coating Fitment Type Direct Replacement Key Features & Benefits Precision Engineering: Manufactured to exact tolerances for seamless fit and function OEM-Equivalent Performance: Meets or exceeds factory specifications for reliable operation Durable Construction: Built with high-quality materials to withstand demanding conditions Easy Installation: Direct bolt-on replacement — no modifications required Corrosion Resistant: Protective coating prevents rust and extends service life Cost-Effective: Premium quality at a fraction of OEM dealer pricing Thoroughly Tested: Each unit undergoes quality inspection before shipment Installation Guide Verify this faucet parts matches your vehicle make, model, and year Gather necessary tools: socket set, wrenches, torque wrench, safety equipment Park vehicle on level surface and engage parking brake Remove the old/damaged component carefully, noting orientation Clean mounting surface and inspect surrounding components for wear Install the new iFJF Faucet Parts in the same orientation Torque all fasteners to manufacturer specifications Test operation before returning vehicle to service ⚠️ Professional installation recommended for safety-critical components. Always consult your vehicle service manual for torque specs. Frequently Asked Questions Q: Is this faucet parts compatible with my vehicle? A: Please verify your vehicle's make, model, year, and engine against our compatibility table above. For specific fitment questions, contact us with your VIN number. Q: Does this replace OEM part numbers RP25513? A: Yes, this faucet parts is designed as a direct replacement for RP25513. It meets or exceeds factory specifications. Q: What's included in the package? A: Each package includes the Faucet Parts assembly as shown. Installation hardware is included where applicable. Please check product images for complete contents. Q: Do you offer a warranty? A: Yes! All iFJF products come with a satisfaction guarantee. If you experience any issues, contact our customer service team for a replacement or refund. Q: How long does shipping take? A: Orders are processed within 1-2 business days. Standard shipping to the contiguous US takes 3-7 business days. Expedited options available at checkout. Related Products Looking for more? Check out these related products from iFJF: iFJF RP25513 Faucet Stem Replacement for Delta Faucet Kit Two Handle F iFJF RP50390 Replacement Hose Kit Rplacement For Delta RP62057 RP74608 Helpful Articles iFJF Blog — Installation Tips, Maintenance Guides & Product Updates How to Choose the Right Aftermarket Parts for Your Vehicle

Read more less

Product Overview The iFJF Faucet Parts is a premium aftermarket replacement part engineered for precision fit and lasting durability. Designed to match or exceed OEM specifications, this faucet parts delivers reliable performance for your vehicle. Compatible Vehicles: Delta Replaces OEM Part Numbers: RP25513 Brand: iFJF Condition: Brand New, Aftermarket Compatibility & Fitment Vehicle Make Model Year Range Engine Delta - - - Technical Specifications Specification Detail Part Type Faucet Parts Brand iFJF Replaces OEM RP25513 Condition New Aftermarket Material High-Grade Steel / Aluminum / Composite Finish Corrosion-Resistant Coating Fitment Type Direct Replacement Key Features & Benefits Precision Engineering: Manufactured to exact tolerances for seamless fit and function OEM-Equivalent Performance: Meets or exceeds factory specifications for reliable operation Durable Construction: Built with high-quality materials to withstand demanding conditions Easy Installation: Direct bolt-on replacement — no modifications required Corrosion Resistant: Protective coating prevents rust and extends service life Cost-Effective: Premium quality at a fraction of OEM dealer pricing Thoroughly Tested: Each unit undergoes quality inspection before shipment Installation Guide Verify this faucet parts matches your vehicle make, model, and year Gather necessary tools: socket set, wrenches, torque wrench, safety equipment Park vehicle on level surface and engage parking brake Remove the old/damaged component carefully, noting orientation Clean mounting surface and inspect surrounding components for wear Install the new iFJF Faucet Parts in the same orientation Torque all fasteners to manufacturer specifications Test operation before returning vehicle to service ⚠️ Professional installation recommended for safety-critical components. Always consult your vehicle service manual for torque specs. Frequently Asked Questions Q: Is this faucet parts compatible with my vehicle? A: Please verify your vehicle's make, model, year, and engine against our compatibility table above. For specific fitment questions, contact us with your VIN number. Q: Does this replace OEM part numbers RP25513? A: Yes, this faucet parts is designed as a direct replacement for RP25513. It meets or exceeds factory specifications. Q: What's included in the package? A: Each package includes the Faucet Parts assembly as shown. Installation hardware is included where applicable. Please check product images for complete contents. Q: Do you offer a warranty? A: Yes! All iFJF products come with a satisfaction guarantee. If you experience any issues, contact our customer service team for a replacement or refund. Q: How long does shipping take? A: Orders are processed within 1-2 business days. Standard shipping to the contiguous US takes 3-7 business days. Expedited options available at checkout. Related Products Looking for more? Check out these related products from iFJF: iFJF RP25513 Faucet Stem Replacement for Delta Faucet Kit Two Handle F iFJF RP50390 Replacement Hose Kit Rplacement For Delta RP62057 RP74608 Helpful Articles iFJF Blog — Installation Tips, Maintenance Guides & Product Updates How to Choose the Right Aftermarket Parts for Your Vehicle

Read more less

Product Overview The iFJF Valve is a premium aftermarket replacement part engineered for precision fit and lasting durability. Designed to match or exceed OEM specifications, this valve delivers reliable performance for your vehicle. Replaces OEM Part Numbers: RP46074 Brand: iFJF Condition: Brand New, Aftermarket Compatibility & Fitment Vehicle Make Model Year Range Engine This product fits multiple applications. Please verify fitment with your vehicle specifications. Technical Specifications Specification Detail Part Type Valve Brand iFJF Replaces OEM RP46074 Condition New Aftermarket Material High-Grade Steel / Aluminum / Composite Finish Corrosion-Resistant Coating Fitment Type Direct Replacement Key Features & Benefits Precision Engineering: Manufactured to exact tolerances for seamless fit and function OEM-Equivalent Performance: Meets or exceeds factory specifications for reliable operation Durable Construction: Built with high-quality materials to withstand demanding conditions Easy Installation: Direct bolt-on replacement — no modifications required Corrosion Resistant: Protective coating prevents rust and extends service life Cost-Effective: Premium quality at a fraction of OEM dealer pricing Thoroughly Tested: Each unit undergoes quality inspection before shipment Installation Guide Verify this valve matches your vehicle make, model, and year Gather necessary tools: socket set, wrenches, torque wrench, safety equipment Park vehicle on level surface and engage parking brake Remove the old/damaged component carefully, noting orientation Clean mounting surface and inspect surrounding components for wear Install the new iFJF Valve in the same orientation Torque all fasteners to manufacturer specifications Test operation before returning vehicle to service ⚠️ Professional installation recommended for safety-critical components. Always consult your vehicle service manual for torque specs. Frequently Asked Questions Q: Is this valve compatible with my vehicle? A: Please verify your vehicle's make, model, year, and engine against our compatibility table above. For specific fitment questions, contact us with your VIN number. Q: Does this replace OEM part numbers RP46074? A: Yes, this valve is designed as a direct replacement for RP46074. It meets or exceeds factory specifications. Q: What's included in the package? A: Each package includes the Valve assembly as shown. Installation hardware is included where applicable. Please check product images for complete contents. Q: Do you offer a warranty? A: Yes! All iFJF products come with a satisfaction guarantee. If you experience any issues, contact our customer service team for a replacement or refund. Q: How long does shipping take? A: Orders are processed within 1-2 business days. Standard shipping to the contiguous US takes 3-7 business days. Expedited options available at checkout. Related Products Looking for more? Check out these related products from iFJF: iFJF RP50587 Single Handle Cartridge Valve Replacement For Cartridge A Helpful Articles iFJF Blog — Installation Tips, Maintenance Guides & Product Updates How to Choose the Right Aftermarket Parts for Your Vehicle

Read more less

Product Overview The iFJF Cartridge is a premium aftermarket replacement part engineered for precision fit and lasting durability. Designed to match or exceed OEM specifications, this cartridge delivers reliable performance for your vehicle. Replaces OEM Part Numbers: RP46463 Brand: iFJF Condition: Brand New, Aftermarket Compatibility & Fitment Vehicle Make Model Year Range Engine This product fits multiple applications. Please verify fitment with your vehicle specifications. Technical Specifications Specification Detail Part Type Cartridge Brand iFJF Replaces OEM RP46463 Condition New Aftermarket Material High-Grade Steel / Aluminum / Composite Finish Corrosion-Resistant Coating Fitment Type Direct Replacement Key Features & Benefits Precision Engineering: Manufactured to exact tolerances for seamless fit and function OEM-Equivalent Performance: Meets or exceeds factory specifications for reliable operation Durable Construction: Built with high-quality materials to withstand demanding conditions Easy Installation: Direct bolt-on replacement — no modifications required Corrosion Resistant: Protective coating prevents rust and extends service life Cost-Effective: Premium quality at a fraction of OEM dealer pricing Thoroughly Tested: Each unit undergoes quality inspection before shipment Installation Guide Verify this cartridge matches your vehicle make, model, and year Gather necessary tools: socket set, wrenches, torque wrench, safety equipment Park vehicle on level surface and engage parking brake Remove the old/damaged component carefully, noting orientation Clean mounting surface and inspect surrounding components for wear Install the new iFJF Cartridge in the same orientation Torque all fasteners to manufacturer specifications Test operation before returning vehicle to service ⚠️ Professional installation recommended for safety-critical components. Always consult your vehicle service manual for torque specs. Frequently Asked Questions Q: Is this cartridge compatible with my vehicle? A: Please verify your vehicle's make, model, year, and engine against our compatibility table above. For specific fitment questions, contact us with your VIN number. Q: Does this replace OEM part numbers RP46463? A: Yes, this cartridge is designed as a direct replacement for RP46463. It meets or exceeds factory specifications. Q: What's included in the package? A: Each package includes the Cartridge assembly as shown. Installation hardware is included where applicable. Please check product images for complete contents. Q: Do you offer a warranty? A: Yes! All iFJF products come with a satisfaction guarantee. If you experience any issues, contact our customer service team for a replacement or refund. Q: How long does shipping take? A: Orders are processed within 1-2 business days. Standard shipping to the contiguous US takes 3-7 business days. Expedited options available at checkout. Related Products Looking for more? Check out these related products from iFJF: iFJF RP70538 Pressure Balance Cartridge for Peerless, Pegasus, Glacier Helpful Articles iFJF Blog — Installation Tips, Maintenance Guides & Product Updates How to Choose the Right Aftermarket Parts for Your Vehicle

Read more less

Product Overview The iFJF Faucet Parts is a premium aftermarket replacement part engineered for precision fit and lasting durability. Designed to match or exceed OEM specifications, this faucet parts delivers reliable performance for your vehicle. Compatible Vehicles: Delta (2057) Replaces OEM Part Numbers: RP50390, RP62057, RP74608 Brand: iFJF Condition: Brand New, Aftermarket Compatibility & Fitment Vehicle Make Model Year Range Engine Delta - 2057 - Technical Specifications Specification Detail Part Type Faucet Parts Brand iFJF Replaces OEM RP50390, RP62057, RP74608 Condition New Aftermarket Material High-Grade Steel / Aluminum / Composite Finish Corrosion-Resistant Coating Fitment Type Direct Replacement Key Features & Benefits Precision Engineering: Manufactured to exact tolerances for seamless fit and function OEM-Equivalent Performance: Meets or exceeds factory specifications for reliable operation Durable Construction: Built with high-quality materials to withstand demanding conditions Easy Installation: Direct bolt-on replacement — no modifications required Corrosion Resistant: Protective coating prevents rust and extends service life Cost-Effective: Premium quality at a fraction of OEM dealer pricing Thoroughly Tested: Each unit undergoes quality inspection before shipment Installation Guide Verify this faucet parts matches your vehicle make, model, and year Gather necessary tools: socket set, wrenches, torque wrench, safety equipment Park vehicle on level surface and engage parking brake Remove the old/damaged component carefully, noting orientation Clean mounting surface and inspect surrounding components for wear Install the new iFJF Faucet Parts in the same orientation Torque all fasteners to manufacturer specifications Test operation before returning vehicle to service ⚠️ Professional installation recommended for safety-critical components. Always consult your vehicle service manual for torque specs. Frequently Asked Questions Q: Is this faucet parts compatible with my vehicle? A: Please verify your vehicle's make, model, year, and engine against our compatibility table above. For specific fitment questions, contact us with your VIN number. Q: Does this replace OEM part numbers RP50390, RP62057, RP74608? A: Yes, this faucet parts is designed as a direct replacement for RP50390, RP62057, RP74608. It meets or exceeds factory specifications. Q: What's included in the package? A: Each package includes the Faucet Parts assembly as shown. Installation hardware is included where applicable. Please check product images for complete contents. Q: Do you offer a warranty? A: Yes! All iFJF products come with a satisfaction guarantee. If you experience any issues, contact our customer service team for a replacement or refund. Q: How long does shipping take? A: Orders are processed within 1-2 business days. Standard shipping to the contiguous US takes 3-7 business days. Expedited options available at checkout. Related Products Looking for more? Check out these related products from iFJF: iFJF RP25513 Faucet Stem Replacement for Delta Faucet Kit Two Handle F iFJF RP25513 Faucet Stem Replacement for Delta Faucet Kit Two Handle F Helpful Articles iFJF Blog — Installation Tips, Maintenance Guides & Product Updates How to Choose the Right Aftermarket Parts for Your Vehicle

Read more less

Product Overview The iFJF Valve is a premium aftermarket replacement part engineered for precision fit and lasting durability. Designed to match or exceed OEM specifications, this valve delivers reliable performance for your vehicle. Replaces OEM Part Numbers: RP50587 Brand: iFJF Condition: Brand New, Aftermarket Compatibility & Fitment Vehicle Make Model Year Range Engine This product fits multiple applications. Please verify fitment with your vehicle specifications. Technical Specifications Specification Detail Part Type Valve Brand iFJF Replaces OEM RP50587 Condition New Aftermarket Material High-Grade Steel / Aluminum / Composite Finish Corrosion-Resistant Coating Fitment Type Direct Replacement Key Features & Benefits Precision Engineering: Manufactured to exact tolerances for seamless fit and function OEM-Equivalent Performance: Meets or exceeds factory specifications for reliable operation Durable Construction: Built with high-quality materials to withstand demanding conditions Easy Installation: Direct bolt-on replacement — no modifications required Corrosion Resistant: Protective coating prevents rust and extends service life Cost-Effective: Premium quality at a fraction of OEM dealer pricing Thoroughly Tested: Each unit undergoes quality inspection before shipment Installation Guide Verify this valve matches your vehicle make, model, and year Gather necessary tools: socket set, wrenches, torque wrench, safety equipment Park vehicle on level surface and engage parking brake Remove the old/damaged component carefully, noting orientation Clean mounting surface and inspect surrounding components for wear Install the new iFJF Valve in the same orientation Torque all fasteners to manufacturer specifications Test operation before returning vehicle to service ⚠️ Professional installation recommended for safety-critical components. Always consult your vehicle service manual for torque specs. Frequently Asked Questions Q: Is this valve compatible with my vehicle? A: Please verify your vehicle's make, model, year, and engine against our compatibility table above. For specific fitment questions, contact us with your VIN number. Q: Does this replace OEM part numbers RP50587? A: Yes, this valve is designed as a direct replacement for RP50587. It meets or exceeds factory specifications. Q: What's included in the package? A: Each package includes the Valve assembly as shown. Installation hardware is included where applicable. Please check product images for complete contents. Q: Do you offer a warranty? A: Yes! All iFJF products come with a satisfaction guarantee. If you experience any issues, contact our customer service team for a replacement or refund. Q: How long does shipping take? A: Orders are processed within 1-2 business days. Standard shipping to the contiguous US takes 3-7 business days. Expedited options available at checkout. Related Products Looking for more? Check out these related products from iFJF: iFJF RP46074 Cartridge For 1300 1400 Tub/Shower Valve Single Lever New Helpful Articles iFJF Blog — Installation Tips, Maintenance Guides & Product Updates How to Choose the Right Aftermarket Parts for Your Vehicle

Read more less

Product Overview The iFJF Cartridge is a premium aftermarket replacement part engineered for precision fit and lasting durability. Designed to match or exceed OEM specifications, this cartridge delivers reliable performance for your vehicle. Replaces OEM Part Numbers: RP70538 Brand: iFJF Condition: Brand New, Aftermarket Compatibility & Fitment Vehicle Make Model Year Range Engine This product fits multiple applications. Please verify fitment with your vehicle specifications. Technical Specifications Specification Detail Part Type Cartridge Brand iFJF Replaces OEM RP70538 Condition New Aftermarket Material High-Grade Steel / Aluminum / Composite Finish Corrosion-Resistant Coating Fitment Type Direct Replacement Key Features & Benefits Precision Engineering: Manufactured to exact tolerances for seamless fit and function OEM-Equivalent Performance: Meets or exceeds factory specifications for reliable operation Durable Construction: Built with high-quality materials to withstand demanding conditions Easy Installation: Direct bolt-on replacement — no modifications required Corrosion Resistant: Protective coating prevents rust and extends service life Cost-Effective: Premium quality at a fraction of OEM dealer pricing Thoroughly Tested: Each unit undergoes quality inspection before shipment Installation Guide Verify this cartridge matches your vehicle make, model, and year Gather necessary tools: socket set, wrenches, torque wrench, safety equipment Park vehicle on level surface and engage parking brake Remove the old/damaged component carefully, noting orientation Clean mounting surface and inspect surrounding components for wear Install the new iFJF Cartridge in the same orientation Torque all fasteners to manufacturer specifications Test operation before returning vehicle to service ⚠️ Professional installation recommended for safety-critical components. Always consult your vehicle service manual for torque specs. Frequently Asked Questions Q: Is this cartridge compatible with my vehicle? A: Please verify your vehicle's make, model, year, and engine against our compatibility table above. For specific fitment questions, contact us with your VIN number. Q: Does this replace OEM part numbers RP70538? A: Yes, this cartridge is designed as a direct replacement for RP70538. It meets or exceeds factory specifications. Q: What's included in the package? A: Each package includes the Cartridge assembly as shown. Installation hardware is included where applicable. Please check product images for complete contents. Q: Do you offer a warranty? A: Yes! All iFJF products come with a satisfaction guarantee. If you experience any issues, contact our customer service team for a replacement or refund. Q: How long does shipping take? A: Orders are processed within 1-2 business days. Standard shipping to the contiguous US takes 3-7 business days. Expedited options available at checkout. Related Products Looking for more? Check out these related products from iFJF: iFJF RP46463 Shower Faucet Replacement Cartridge For 2006-Present 1700 Helpful Articles iFJF Blog — Installation Tips, Maintenance Guides & Product Updates How to Choose the Right Aftermarket Parts for Your Vehicle

Read more less

Product Overview The iFJF Filter is a premium aftermarket replacement part engineered for precision fit and lasting durability. Designed to match or exceed OEM specifications, this filter delivers reliable performance for your vehicle. Compatible Vehicles: Dometic Brand: iFJF Condition: Brand New, Aftermarket Engine Compatibility: 3104928.019 Compatibility & Fitment Vehicle Make Model Year Range Engine Dometic - - - Technical Specifications Specification Detail Part Type Filter Brand iFJF Condition New Aftermarket Material High-Grade Steel / Aluminum / Composite Finish Corrosion-Resistant Coating Fitment Type Direct Replacement Engine Compatibility 3104928.019 Key Features & Benefits Precision Engineering: Manufactured to exact tolerances for seamless fit and function OEM-Equivalent Performance: Meets or exceeds factory specifications for reliable operation Durable Construction: Built with high-quality materials to withstand demanding conditions Easy Installation: Direct bolt-on replacement — no modifications required Corrosion Resistant: Protective coating prevents rust and extends service life Cost-Effective: Premium quality at a fraction of OEM dealer pricing Thoroughly Tested: Each unit undergoes quality inspection before shipment Installation Guide Verify this filter matches your vehicle make, model, and year Gather necessary tools: socket set, wrenches, torque wrench, safety equipment Park vehicle on level surface and engage parking brake Remove the old/damaged component carefully, noting orientation Clean mounting surface and inspect surrounding components for wear Install the new iFJF Filter in the same orientation Torque all fasteners to manufacturer specifications Test operation before returning vehicle to service ⚠️ Professional installation recommended for safety-critical components. Always consult your vehicle service manual for torque specs. Frequently Asked Questions Q: Is this filter compatible with my vehicle? A: Please verify your vehicle's make, model, year, and engine against our compatibility table above. For specific fitment questions, contact us with your VIN number. Q: Does this replace OEM part numbers the original? A: Yes, this filter is designed as a direct replacement forthe OEM component. It meets or exceeds factory specifications. Q: What's included in the package? A: Each package includes the Filter assembly as shown. Installation hardware is included where applicable. Please check product images for complete contents. Q: Do you offer a warranty? A: Yes! All iFJF products come with a satisfaction guarantee. If you experience any issues, contact our customer service team for a replacement or refund. Q: How long does shipping take? A: Orders are processed within 1-2 business days. Standard shipping to the contiguous US takes 3-7 business days. Expedited options available at checkout. Related Products Looking for more? Check out these related products from iFJF: iFJF RV Water Filter Uses Multiple Layers of Filtration Materials, Gre Helpful Articles iFJF Blog — Installation Tips, Maintenance Guides & Product Updates How to Choose the Right Aftermarket Parts for Your Vehicle

Read more less

Product Overview The iFJF Circuit Board is a premium aftermarket replacement part engineered for precision fit and lasting durability. Designed to match or exceed OEM specifications, this circuit board delivers reliable performance for your vehicle. Replaces OEM Part Numbers: DM2663, RM2354, RM2454, RM2554 Brand: iFJF Condition: Brand New, Aftermarket Compatibility & Fitment Vehicle Make Model Year Range Engine This product fits multiple applications. Please verify fitment with your vehicle specifications. Technical Specifications Specification Detail Part Type Circuit Board Brand iFJF Replaces OEM DM2663, RM2354, RM2454, RM2554 Condition New Aftermarket Material High-Grade Steel / Aluminum / Composite Finish Corrosion-Resistant Coating Fitment Type Direct Replacement Key Features & Benefits Precision Engineering: Manufactured to exact tolerances for seamless fit and function OEM-Equivalent Performance: Meets or exceeds factory specifications for reliable operation Durable Construction: Built with high-quality materials to withstand demanding conditions Easy Installation: Direct bolt-on replacement — no modifications required Corrosion Resistant: Protective coating prevents rust and extends service life Cost-Effective: Premium quality at a fraction of OEM dealer pricing Thoroughly Tested: Each unit undergoes quality inspection before shipment Installation Guide Verify this circuit board matches your vehicle make, model, and year Gather necessary tools: socket set, wrenches, torque wrench, safety equipment Park vehicle on level surface and engage parking brake Remove the old/damaged component carefully, noting orientation Clean mounting surface and inspect surrounding components for wear Install the new iFJF Circuit Board in the same orientation Torque all fasteners to manufacturer specifications Test operation before returning vehicle to service ⚠️ Professional installation recommended for safety-critical components. Always consult your vehicle service manual for torque specs. Frequently Asked Questions Q: Is this circuit board compatible with my vehicle? A: Please verify your vehicle's make, model, year, and engine against our compatibility table above. For specific fitment questions, contact us with your VIN number. Q: Does this replace OEM part numbers DM2663, RM2354, RM2454? A: Yes, this circuit board is designed as a direct replacement for DM2663, RM2354, RM2454. It meets or exceeds factory specifications. Q: What's included in the package? A: Each package includes the Circuit Board assembly as shown. Installation hardware is included where applicable. Please check product images for complete contents. Q: Do you offer a warranty? A: Yes! All iFJF products come with a satisfaction guarantee. If you experience any issues, contact our customer service team for a replacement or refund. Q: How long does shipping take? A: Orders are processed within 1-2 business days. Standard shipping to the contiguous US takes 3-7 business days. Expedited options available at checkout. Related Products Looking for more? Check out these related products from iFJF: iFJF Rev Counter Board Compatible with FM350 FM352 FM500 FM502 FM600 2 Helpful Articles iFJF Blog — Installation Tips, Maintenance Guides & Product Updates How to Choose the Right Aftermarket Parts for Your Vehicle

Read more less

Product Overview The iFJF Motor is a premium aftermarket replacement part engineered for precision fit and lasting durability. Designed to match or exceed OEM specifications, this motor delivers reliable performance for your vehicle. Compatible Vehicles: Lippert Brand: iFJF Condition: Brand New, Aftermarket Compatibility & Fitment Vehicle Make Model Year Range Engine Lippert - - - Technical Specifications Specification Detail Part Type Motor Brand iFJF Condition New Aftermarket Material High-Grade Steel / Aluminum / Composite Finish Corrosion-Resistant Coating Fitment Type Direct Replacement Key Features & Benefits Precision Engineering: Manufactured to exact tolerances for seamless fit and function OEM-Equivalent Performance: Meets or exceeds factory specifications for reliable operation Durable Construction: Built with high-quality materials to withstand demanding conditions Easy Installation: Direct bolt-on replacement — no modifications required Corrosion Resistant: Protective coating prevents rust and extends service life Cost-Effective: Premium quality at a fraction of OEM dealer pricing Thoroughly Tested: Each unit undergoes quality inspection before shipment Installation Guide Verify this motor matches your vehicle make, model, and year Gather necessary tools: socket set, wrenches, torque wrench, safety equipment Park vehicle on level surface and engage parking brake Remove the old/damaged component carefully, noting orientation Clean mounting surface and inspect surrounding components for wear Install the new iFJF Motor in the same orientation Torque all fasteners to manufacturer specifications Test operation before returning vehicle to service ⚠️ Professional installation recommended for safety-critical components. Always consult your vehicle service manual for torque specs. Frequently Asked Questions Q: Is this motor compatible with my vehicle? A: Please verify your vehicle's make, model, year, and engine against our compatibility table above. For specific fitment questions, contact us with your VIN number. Q: Does this replace OEM part numbers the original? A: Yes, this motor is designed as a direct replacement forthe OEM component. It meets or exceeds factory specifications. Q: What's included in the package? A: Each package includes the Motor assembly as shown. Installation hardware is included where applicable. Please check product images for complete contents. Q: Do you offer a warranty? A: Yes! All iFJF products come with a satisfaction guarantee. If you experience any issues, contact our customer service team for a replacement or refund. Q: How long does shipping take? A: Orders are processed within 1-2 business days. Standard shipping to the contiguous US takes 3-7 business days. Expedited options available at checkout. Related Products Looking for more? Check out these related products from iFJF: iFJF RV Stair Entry Step Motor For Kwikee 676061 1101428 Stripped Gear Helpful Articles iFJF Blog — Installation Tips, Maintenance Guides & Product Updates How to Choose the Right Aftermarket Parts for Your Vehicle

Read more less