Description
Overview
Stop pool hose stress cracks before they start with the iFJF 2-Pack 1.25 inch Swimming Pool Pipe Holders. These essential accessories provide structural support for suction and return hoses on Intex filtration pump systems eliminating tension and pulling that leads to cracked pool wall connections leaking liners and detached hoses. Each set includes two pipe holders and three clamps — everything needed to protect both sides of your pool plumbing.
Compatibility
| Category |
Compatible Products |
| Pool Type |
Intex Above-Ground Pools with 1.25 inch Hose Connections |
| Filter Pumps |
Intex 1500 GPH 2500 GPH 4000 GPH Filtration Systems |
| Hose Diameter |
1.25 Inches (32mm) Standard Intex Hose |
Verify your hose diameter before ordering. Intex offers both 1.25 inch and 1.5 inch hose connections on different models.
Key Features
-
Complete 2-Pack Value: Includes 2 pipe holders — one for suction side and one for return side of filtration system
-
3 Secure Clamps: Tight-grip plastic clamps prevent hose slippage even under full pump pressure
-
Optimized for 1.25 inch Hoses: Precision-fit for standard Intex 1.25 inch (32mm) pool hoses
-
UV-Resistant Material: High-quality outdoor-grade plastic withstands sun exposure without becoming brittle
-
Stress Relief Design: Reduces tension and pulling at pool wall inlet/outlet connections preventing cracks and liner leaks
-
Tool-Free Installation: Simply mount connect and clamp — no special tools or plumbing expertise required
Technical Specifications
| Specification |
Value |
| Hose Diameter |
1.25 Inches (32mm) |
| Material |
High-Grade UV-Resistant Plastic |
| Package Quantity |
2 Pipe Holders + 3 Plastic Clamps |
| Recommended Pumps |
Intex 1500 2500 4000 GPH Filter Pumps |
| Installation |
Tool-Free — Under 15 Minutes |
Installation
-
Drain Pool Below Connections: Lower water level below inlet and outlet ports or plug from inside
-
Position Holder: Place pipe holder at pool wall interface where hose connects
-
Connect Hose: Attach 1.25 inch Intex hose to pool wall fitting as normal
-
Secure with Clamp: Position clamp over hose and pipe holder junction tighten until snug
-
Repeat: Install second pipe holder on opposite connection suction/return
-
Test: Refill to operating level start pump and check for leaks or hose movement
Why Choose iFJF?
-
Factory Direct Supply: iFJF manufactures its own pool replacement parts — no middleman markups
-
Preventative Solution: Much cheaper than replacing cracked pool liner or leaking wall connection from unsupported hoses
-
Bulk Orders Welcome: Need replacements for multiple pools? Contact support@ifjf.net for wholesale pricing
-
Universal Intex Fit: Designed to work with all standard Intex above-ground pool hose connections
FAQ
Q: Will these work with 1.5 inch Intex hoses?
A: No these are specifically designed for 1.25 inch (32mm) hoses. If your Intex system uses 1.5 inch hoses these will not fit properly.
Q: How many pipe holders do I need for one pool?
A: This 2-pack provides one holder for suction side and one for return side — sufficient for single Intex above-ground pool.
Q: Do these work with non-Intex brand filter pumps?
A: Designed for Intex hose connection standard. Compatibility with other brands depends on hose diameter and connection type.
Q: Can I use for rigid PVC pipe instead of flexible hose?
A: Designed for flexible Intex pool hoses. Not suitable for rigid PVC pipe installations.
Q: Will the plastic crack in cold weather?
A: UV-resistant plastic is formulated for outdoor temperature ranges. For winter store holders indoors for maximum longevity.
Q: Is professional installation required?
A: No designed for simple DIY installation. No plumbing experience or special tools needed.
