Search results for "nova"
iFJF 134001 Fuel Filter Housing Cap for 6.6L L5P & 3.0L Duramax LM2/LZ0
CNC Billet Aluminum Fuel Filter Housing Cap — Replaces 134001 on 6.6L L5P & 3.0L LM2/LZ0 Duramax This 134001 billet aluminum fuel filter housing cap is the direct replacement for the factory plastic cap on every GM Duramax that runs the ACDelco TP1015 cartridge filter: 2017-2026 6.6L L5P in the Silverado and Sierra 2500HD / 3500HD, and 2020-2026 3.0L LM2 / LZ0 in the Silverado and Sierra 1500. It threads into the factory housing (GM 13539472), turns with a 36mm (1-3/8") socket, seals with the large O-ring out of your ACDelco TP1015 filter kit, and torques to 25 N·m / 18 ft-lb. No adapter ring, no thread insert, no modification. The cap ships on its own — the O-rings live in the filter box, not with the cap. Key Features 6061-T6 Billet Aluminum: CNC-machined from solid billet stock — not cast, not molded. The threads are cut, not formed, so they hold their profile through every heat cycle and every filter change. Machined O-Ring Groove: The seal seat is cut to ±0.001" so the ring from your TP1015 kit drops in and stays put while the cap turns. An O-ring that rides up onto the threads instead of sitting in the groove is the single most common cause of a leaking housing cap. Hard-Coat Anodized Finish: Resists road salt, diesel exposure and under-hood chemicals. It will not pit, oxidize or chalk like raw aluminum. Correct 36mm Hex: The same size as the factory cap, so the socket you already own fits — 1-3/8" works too. No strap wrench, no pipe pliers, no chewed-up hex. Stainless Steel Drain Screw: The drain screw sits at the low point of the inverted housing, exactly where the factory T40 screw sits. Machined from stainless steel with an integrated sealing washer — it will not seize, round out or weep after repeated water drains. One Cap, Two Engines: The 6.6L L5P and the 3.0L LM2 / LZ0 share the same fuel filter housing and the same TP1015 element. This cap fits both, which is why it is sold as one part number instead of two. Vehicle Compatibility Make Model Years Engine Chevrolet Silverado 2500HD 2017-2026 6.6L Duramax L5P Chevrolet Silverado 3500HD 2017-2026 6.6L Duramax L5P GMC Sierra 2500HD 2017-2026 6.6L Duramax L5P GMC Sierra 3500HD 2017-2026 6.6L Duramax L5P Chevrolet Silverado 1500 2020-2026 3.0L Duramax LM2 / LZ0 GMC Sierra 1500 2020-2026 3.0L Duramax LM2 / LZ0 Chevrolet Tahoe / Suburban 2021-2026 3.0L Duramax LM2 / LZ0 GMC Yukon / Yukon XL 2021-2026 3.0L Duramax LM2 / LZ0 Cadillac Escalade / Escalade ESV 2021-2026 3.0L Duramax LM2 / LZ0 Will not fit: 2016 and earlier Duramax (LML / LGH) — those trucks use a spin-on TP3018 canister and have no threaded housing cap. Also not for gasoline engines or for the DEF / diesel exhaust fluid filler. Technical Specifications Specification Value Part type Fuel filter housing cap (housing cover) Replaces OEM cap 134001 Matches housing GM 13539472 Filter used ACDelco TP1015 / GM 13539108 / 23304096 Material 6061-T6 billet aluminum Manufacturing CNC machined — not cast, not molded Finish Hard-coat anodized, corrosion resistant Socket size 36mm (1-3/8" also fits) Drain screw Stainless steel, T40 Torx O-rings included No — cap only. New O-rings are supplied in the ACDelco TP1015 filter box Cap torque 25 N·m / 18 ft-lb Drain screw torque 2 N·m / 1.5 ft-lb Weight Approx. 0.45 lb Why the Factory Plastic Cap Fails The OEM cap is glass-filled nylon. Every filter change means another 18 ft-lb of torque on plastic threads that have already been through hundreds of heat cycles, from a -20°F cold start to 220°F+ under-hood temperatures while towing. The nylon loses its thread profile, and the hex starts to round. From there it fails one of three ways: the cap stops sealing and diesel weeps past the O-ring, the hex rounds out so the cap cannot be removed, or the cap cracks outright and the fuel system starts drawing air. Air is the expensive part. The CP4.2 high-pressure pump is lubricated and cooled by the fuel it pumps — an air pocket means metal-on-metal contact inside a $1,500+ pump, and the debris it makes travels straight into the injectors. A billet aluminum cap removes all three failure modes for the cost of one filter change. Installation — Cap Replacement With a New Filter Allow 20-30 minutes. Work on level ground with the engine cold. Gather the tools. 36mm 6-point socket (1-3/8" also fits), ratchet, torque wrench that reads 18 ft-lb, T40 Torx bit, pick tool, drain pan, clean diesel for lubrication, gloves, and a new ACDelco TP1015 filter. Find the housing. The housing hangs cap-down. On 2020-2026 trucks it is mounted on the driver-side frame rail, roughly below the rear door — reachable from the ground without a lift. Mounting height and orientation vary by model year, so confirm which way the cap faces before you start. If your truck has air suspension, raise it to the highest setting and enable Service Mode first. Clean the outside first. Wash the housing with soapy water and dry it. Never spray brake cleaner on the plastic housing — grit that gets pushed inside while the cap is off goes straight into the fuel system. Drain the housing (optional). Crack the T40 drain screw at the low point of the cap and let the diesel run into the pan. On many trucks it only trickles — plan for roughly a quart to come out when the cap releases either way. Remove the cap. Set the drain pan underneath, fit the 36mm socket and turn counterclockwise. Break it loose, then unwind by hand as the flow slows. Separate the old element. The filter clips onto a stem in the center of the cap. Rock it side to side and pull it straight off — do not pry with a screwdriver against the sealing surface. Fit the new O-rings from the filter box. Have the TP1015 filter on hand before you start. Use the pick tool to lift the old O-rings out of their grooves without scratching them. One large O-ring seals the cap; the small one lives on the center pickup tube inside the housing and seals the clean side from the dirty side. A missed small O-ring sends unfiltered fuel straight to the high-pressure pump. Lubricate each new O-ring with clean diesel — not grease, not engine oil. Seat the large O-ring in the groove. On the new cap, the O-ring drops into the machined groove below the threads. If it sits on the threads instead, tightening will roll and pinch it, and the cap will weep within a few hundred miles. This is the mistake behind most leaking cap installs. Assemble the new filter. Press the narrow end of the TP1015 element onto the cap stem until it clicks, and check that it stands straight rather than cocked to one side. Pre-fill and install. Pour clean diesel into the housing to about 80% — it shortens priming. Thread the cap on by hand until the O-ring contacts, then torque to 25 N·m / 18 ft-lb. If you use the drain screw, snug it to 2 N·m / 1.5 ft-lb only; it is a sealing screw, not a structural one. Prime the system. Keep your foot completely off the brake pedal and hold the START button for about 10 seconds to reach RUN without cranking. Release, then repeat once — the lift pump runs and pushes air out of the housing. On vehicles with a key, cycle to ON for 10 seconds twice instead. Then brake on and start the engine. Check for leaks. Let the engine idle, then look at the cap threads and drain screw for any dampness. A dry cap after 2-3 minutes of running is a sealed cap. Reset the monitor. In the driver information center, open Fuel Filter Life and hold Reset to bring it back to 100%. Some trucks only accept the reset after a key-off / key-on cycle. Frequently Asked Questions Q: Will this cap fit a 2024 Silverado 1500 with the 3.0L Duramax? A: Yes. The 2020-2026 Silverado 1500 and Sierra 1500 with the 3.0L LM2 or LZ0 Duramax use the same fuel filter housing (GM 13539472) and the same TP1015 element as the 6.6L L5P, so the cap threads, the 36mm hex and the O-ring groove are identical. Q: Why do most listings say this cap only fits the 2500HD and 3500HD? A: Because the 6.6L L5P was the first and largest market for this cap, so sellers list it under the heavy-duty trucks. The 3.0L LM2 and LZ0 use the same housing and the same TP1015 filter, so the cap fits both families. Q: What torque should the cap be tightened to? A: 25 N·m, which is 18 ft-lb. Use a torque wrench rather than guessing — overtightening pinches the O-ring and can seize the cap on the housing threads. The small drain screw takes only 2 N·m / 1.5 ft-lb. Q: Are the O-rings included with the cap? A: No. This listing is the housing cap only — the O-rings come in the ACDelco TP1015 filter box. Fit the new filter at the same time as the cap, seat the large O-ring in the machined groove below the cap threads (never on the threads), and lubricate it with clean diesel before installing. Q: Do I need to replace the O-rings every time I change the filter? A: Yes. O-rings take a permanent set once they have been compressed under heat, so a reused ring seals poorly even when it looks intact. Q: Does the aluminum cap need a different socket than the factory cap? A: No. Both use a 36mm socket, and a 1-3/8" socket also fits. A 32mm socket, which is often quoted for older Duramax filters, does not fit this housing. Q: Will this cap fit a 2016 or older Duramax? A: No. Trucks through 2016 with the LML or LGH engine use a spin-on TP3018 canister and do not have a threaded housing cap. Q: Can the aluminum cap crack like the plastic one? A: The cap is machined from solid 6061-T6 billet rather than molded, and aluminum does not become brittle from heat cycling the way glass-filled nylon does, so it does not develop the stress cracks that make plastic caps weep. OEM Cross-Reference Number Type 134001 Fuel filter housing cap (this part) 13539472 GM housing the cap threads into TP1015 / 13539108 / 23304096 / 22937279 Filter element the cap holds Related Reading Your L5P's Plastic Fuel Filter Cap Is a Ticking Time Bomb — Here's the Fix Duramax 6.6L L5P Fuel Filter Replacement: Complete Step-by-Step Guide Manufactured under an ISO 9001:2015 quality management system and an IATF 16949:2016 automotive quality management system.
$69.99
iFJF Performer 600 CFM Carburetor 4 Barrel Electric Choke — Square Bore Air Valve Non-EGR 1806
Product Overview The iFJF 1806 Performer 600 CFM carburetor delivers the ideal balance of street performance and daily driveability for small block and mild big block V8 engines. Featuring electric choke, air valve secondaries, and non-EGR calibration, this 4-barrel square bore carburetor is pre-calibrated for a wide range of engines from 305 to 402 cubic inches. Whether you're upgrading from a worn-out factory carb or building a fresh engine, the 1806 delivers out-of-the-box performance. Key Features 600 CFM — Universal Sweet Spot — The most versatile CFM rating for street V8s. Works well on everything from mild 305s to warmed-up 400s without over-carbureting. Air Valve Secondary — The secondary air valve opens progressively based on airflow demand. No bog, no hesitation — just smooth, seamless power delivery. Electric Choke (12V) — Automatic choke with adjustable housing. Fast warm-up, consistent cold starts in any season. Non-EGR Design — No exhaust gas recirculation provisions. Perfect for pre-emissions vehicles, off-road applications, or engines with EGR delete modifications. Two-Piece Aluminum Construction — Fewer gasket surfaces than three-piece designs. Resists warping and fuel leaks better than pot metal castings. Pre-Calibrated & Flow Tested — Each carburetor is wet-flow tested on a calibration engine before packaging. Ready to run with minimal tuning. Compatibility Engine Family Displacement Typical Vehicles Chevy Small Block 305, 327, 350, 383, 400 Camaro, Chevelle, C10, Nova, Impala, Monte Carlo Ford Windsor/Cleveland 302, 351W, 351C, 400M Mustang, F-150, Bronco, Torino, Cougar Mopar LA/Magnum 318, 340, 360 Charger, Challenger, Dart, Duster, Ram, Dakota AMC V8 304, 360, 390, 401 Javelin, AMX, CJ, Wagoneer, Cherokee Buick/Olds/Pontiac V8 301-403 Square bore intake required Specifications Parameter Value Part Number 1806 CFM Rating 600 CFM Barrel Type 4-Barrel Square Bore Choke 12V Electric Secondary Type Air Valve (Adjustable) Body Material Die-Cast Aluminum (Two-Piece) EGR Non-EGR (No EGR Provisions) Why iFJF Performer 1806? The 600 CFM Performer has been the go-to street performance carburetor for decades. Our 1806 builds on that legacy with modern manufacturing precision. The air valve secondary design is inherently smoother than mechanical secondaries for street driving — you don't get the sudden "hit" that can break tires loose unexpectedly on wet pavement. Combined with the 12V electric choke, this is the set-it-and-forget-it carburetor that starts reliably and drives smoothly from cold mornings to hot summer afternoons. Frequently Asked Questions Q: Will this fit my 350 Chevy with an Edelbrock Performer intake?A: Yes. The 1806 has a standard square bore flange that matches the Edelbrock Performer, Performer RPM, and most other aftermarket intakes. Direct bolt-on — no adapter needed. Q: What's air valve secondary vs. vacuum secondary?A: Air valve secondaries use a spring-loaded flap above the secondary throttle plates. As airflow increases, the valve opens progressively — providing smoother engagement than mechanical secondaries and more precise control than pure vacuum secondaries. Q: Will this work with my TH350 automatic transmission?A: Yes. The throttle lever includes provisions for GM TH350, TH400, 700R4, and 200-4R kickdown cables. Ford AOD and C4/C6 linkages are also supported with the correct bracket. Q: Does non-EGR mean it won't pass emissions?A: Non-EGR carburetors are intended for pre-emissions vehicles (generally pre-1975), off-road vehicles, or vehicles where the EGR system has been removed. Not for use on emissions-controlled vehicles where EGR is required by law. Q: Can I use this on a marine engine?A: No. Marine engines require USCG-approved carburetors with specific safety features (sealed overflow, J-tube venting). Use only marine-rated carburetors on boats. Q: What timing should I run with this carburetor?A: For most small block Chevy engines, start with 10-12° initial timing and 34-36° total mechanical advance by 3,000 RPM. Adjust vacuum advance to provide 10-12° additional under light cruise.
$339.99
iFJF Quadrajet 4MV 750 CFM Carburetor for 1966-1973 Chevy 327-454 — Corvette 1975-1979 Replacement
Product Overview This iFJF 1901R Quadrajet 4MV 750 CFM 4-barrel carburetor is a precision-engineered replacement for 1966-1973 Chevy vehicles (327, 350, 396, 427, 454 engines) and 1975-1979 C3 Corvettes. Designed as a direct bolt-on upgrade, it delivers reliable fuel delivery with vacuum secondaries and manual choke operation — ideal for street performance, restoration projects, and daily drivers. Key Features 750 CFM Flow Rate — Optimized for small block and big block Chevy engines from 327 to 454 cubic inches, providing balanced air/fuel mixture across the entire RPM range. Vacuum Secondary Operation — Secondaries open progressively based on engine demand, preventing bogging while delivering full power when you need it. Manual Choke Control — Gives you complete control over cold starts — no fussy automatic choke mechanisms to fail. All-Aluminum Construction — Two-piece die-cast aluminum body resists warping, corrosion, and fuel degradation better than original pot metal castings. Square Bore Flange — Standard 4-barrel square bore pattern fits OEM Quadrajet intake manifolds with no adapter required. Compatibility Year Make Model Engine 1966-1973 Chevrolet Camaro, Chevelle, Nova, Impala, C10, C20 327, 350, 396, 427, 454 1975-1979 Chevrolet Corvette (C3) 350, 454 1966-1973 Chevrolet Chevy II, Monte Carlo, El Camino 327, 350, 396, 454 1968-1973 GMC C15, C25, K15, K25 Trucks 350, 396, 454 Specifications Parameter Value Part Number 1901R (Replaces 7026202, 7026203, 7026210, 7027202, 7027203) CFM Rating 750 CFM Barrels 4-Barrel (Square Bore) Choke Type Manual Choke Secondary Type Vacuum Secondary Body Material Die-Cast Aluminum Throttle Bore 1-11/16" Primary / 2-1/4" Secondary Fuel Inlet Single 5/8"-20 Thread Finish Natural Cast Aluminum Why Choose iFJF 1901R Quadrajet? The original Rochester Quadrajet was a brilliant design but suffered from warped bodies, leaky well plugs, and worn throttle shafts after decades of service. Our 1901R replacement addresses all these weaknesses with modern CNC machining, improved aluminum alloy, and precision calibration. You get the signature Quadrajet sound and performance without the headaches of a 50-year-old core. Each unit is wet-flow tested before leaving the factory. We stand behind every carburetor with our satisfaction guarantee. Installation Tips Verify intake manifold is square bore pattern (not spread bore without adapter) Set idle mixture screws to 2-1/2 turns out as starting point Use a phenolic spacer to reduce heat soak on hot starts Check fuel pressure — Quadrajets prefer 5-6 PSI maximum Connect choke cable to manual choke linkage before final mounting Torque mounting bolts to 12-15 ft-lbs in a crisscross pattern Frequently Asked Questions Q: Will this fit my 1969 Camaro with a 350?A: Yes. This 1901R Quadrajet 4MV is a direct replacement for 1966-1973 Chevy 327-454 engines with a square bore intake manifold. Your 1969 Camaro 350 is a perfect match. Q: Does this carburetor come with a gasket?A: Yes, a base gasket is included. We recommend using a quality fiber gasket or 1/4" phenolic spacer for best results. Q: Is this a rebuilt original or brand new?A: This is a 100% brand new carburetor — not a remanufactured or rebuilt core. No core charge, no waiting for a rebuild. Q: Do I need an adapter to install this on a spread bore manifold?A: This is a square bore carburetor. If your intake manifold is a spread bore (common on later Quadrajets), you will need a square-to-spread bore adapter plate (sold separately). Q: How do I adjust the manual choke?A: The choke lever connects to a standard choke cable (not included). Route the cable through your firewall and mount under the dash. Pull to close choke for cold starts, push to open as engine warms. Q: What's the difference between vacuum secondary and mechanical secondary?A: Vacuum secondaries open based on engine load — they only engage when the engine can actually use the extra air/fuel. This prevents bogging and improves driveability on the street compared to mechanical secondaries. Q: Does this carburetor have EGR provisions?A: No. This carburetor does not include EGR provisions, making it ideal for non-emissions applications, off-road use, or vehicles with EGR deleted.
$389.99
iFJF Edelbrock 1406 Performer 600 CFM 4-Barrel Carburetor — Electric Choke, for Chevy/GMC/Ford (Gold)
Edelbrock 1406 Performer 600 CFM Carburetor — Electric Choke, AFB-Style The iFJF 1406 Performer Series Carburetor is the go-to 600 CFM 4-barrel for street performance enthusiasts who want plug-and-play reliability. Featuring an electric choke for hassle-free cold starts and the legendary AFB-style air valve secondary design, this carburetor is a direct replacement for the Edelbrock 1406 and fits a wide range of GM, Ford, and Mopar V8 engines. Key Features 600 CFM Airflow — Ideal airflow for mild to moderate street V8 builds from 305 to 454 cubic inches Electric Choke — Automatic cold-start enrichment with 12V connection — no choke cable to route through the firewall AFB-Style Architecture — No power valves to fail; metering rods provide consistent fuel curve across all RPM ranges 4-Barrel Square Bore — Bolts directly to Edelbrock Performer, Performer RPM, and most aftermarket square bore intakes Gold Dichromate Finish — Timeless hot-rod aesthetic with excellent corrosion protection Two-Piece Design — Access jets and metering rods in minutes without removing the carburetor Air Valve Secondary — Smooth, progressive secondary opening eliminates bog Vehicle Compatibility Make Models Engine Chevrolet / GMC Silverado, C/K Series, Camaro, Chevelle, Nova, Impala, Suburban, Blazer 305, 327, 350, 383, 400, 454 V8 Ford / Mercury Mustang, F-150, Torino, Cougar, Fairlane, Galaxy 302, 351W, 351C, 390, 428, 460 V8 Chrysler / Dodge / Plymouth Charger, Challenger, Road Runner, Barracuda, D100/D150 318, 340, 360, 383, 440 V8 Technical Specifications Specification Value CFM Rating 600 CFM Barrels 4-Barrel Choke Type Electric (12V) Flange Type Square Bore Finish Gold Dichromate Secondary Type Air Valve (Mechanical) EGR No EGR Provision Why the 1406? The electric choke on the 1406 makes cold starts effortless — just pump the gas once, turn the key, and the 12V choke element handles the rest. The AFB-style metering rod system delivers consistent air/fuel ratios without the power valve failure headaches common on competing designs. Whether it's a daily-driven Silverado, a weekend Mustang, or a restomod GMC, the 1406 is the most popular street performance carburetor for a reason. Frequently Asked Questions Q: How do I wire the electric choke? A: Connect the choke's positive terminal to a 12V ignition-switched source (key-on power only). The most reliable connection point is the ignition coil positive terminal or the fuse box IGN terminal. Do NOT connect to the alternator or a constant 12V source — the choke only needs power when the engine is running. Q: Will this fit my Ford 302? A: Yes, it fits any engine with a square bore intake manifold. For Ford 302 applications, pair with a Performer or Performer RPM intake manifold. You may need a throttle bracket adapter for Ford throttle cable compatibility. Q: What's the difference between the 1405 and 1406? A: The 1405 has a manual choke (cable-operated), while the 1406 has an electric choke. Internally, the jetting and calibration are nearly identical. Choose the 1406 if you want automatic cold-start convenience; choose the 1405 if you prefer manual control or are building a race/off-road application. Q: Do I need a calibration kit? A: The 1406 comes pre-calibrated for typical street V8 applications from sea level to approximately 4,000 feet. At higher altitudes or for modified engines with aggressive cams, a metering rod/jet calibration kit is recommended. Q: What fuel pressure is required? A: The 1406 operates best at 5.5-6.0 PSI fuel pressure. Use a quality fuel pressure regulator if your mechanical or electric pump exceeds 6.5 PSI, as excessive pressure can overpower the needle and seat. Q: Is this compatible with EGR? A: No — this is a non-EGR carburetor designed for performance applications. For off-road and racing use only where emissions equipment removal is legal. 🔗 Related Products from iFJF 1405 Performer 600 CFM Carburetor (Manual Choke) 1404 Performer 500 CFM Carburetor 1478 Electric Choke Kit for 1405/1406 📚 Helpful Installation Guides 📖 How To Rebuild Edelbrock 1406 and 1405 Carburetors | Rebuild Kit Links 📖 iFJF 1403 Performer 500 CFM 4-Barrel Carburetor Installation Guide 📖 Related Guide Read our How to Rebuild Edelbrock 1406 & 1405 Carburetors for step-by-step rebuild instructions and kit recommendations. Installing a Performer-pattern 4-barrel? Read our iFJF 1403 Performer 500 CFM 4-Barrel Carburetor Installation Guide for the full bolt-on sequence.
$419.99
iFJF Edelbrock 1405 Performer 600 CFM 4-Barrel Carburetor — Manual Choke, Square Bore, for Chevy/GMC V8 (Gold)
Edelbrock 1405 Performer 600 CFM Carburetor — Manual Choke, Square Bore The iFJF 1405 Performer Series Carburetor delivers 600 CFM of reliable airflow with a manual choke and classic square bore design. Built as a direct replacement for the legendary Edelbrock 1405, this carburetor is engineered for street performance and daily driving on Chevy small block and big block V8 engines including the Corvette, Silverado, GMC trucks, and 366 Demon Poly applications. Key Features 600 CFM Airflow — Optimized for 305-454 cubic inch V8 engines delivering crisp throttle response Manual Choke — Full driver control over cold-start enrichment, ideal for performance builds 4-Barrel Square Bore — Standard square bore flange fits Edelbrock Performer, Performer RPM, and stock 4-barrel intake manifolds AFB-Style Design — Tried-and-true Carter AFB architecture with no power valves to blow out Gold Dichromate Finish — Classic hot-rod look with superior corrosion resistance Two-Piece Body — Easy to tune and service without removing from the manifold Electric Choke Compatible — Can be upgraded with iFJF 1478 Electric Choke Kit (sold separately) Vehicle Compatibility Make Model Engine Notes Chevrolet Corvette, Camaro, Chevelle, Nova, Silverado, C10, Impala 305, 327, 350, 383, 396, 400, 427, 454 V8 Square bore intake required GMC Sierra, C/K1500, Jimmy, Suburban 305, 350, 396, 454 V8 Verify intake manifold flange Pontiac Firebird, Trans Am, GTO, Grand Prix 350, 400, 455 V8 Aftermarket intake recommended Oldsmobile Cutlass, 442, Delta 88 350, 403, 455 V8 Check hood clearance Technical Specifications Specification Value CFM Rating 600 CFM Barrels 4-Barrel Choke Type Manual Flange Type Square Bore Finish Gold Dichromate Secondary Type Air Valve (Mechanical) Fuel Type Gasoline EGR No EGR Provision Why Choose the iFJF 1405? The AFB-style architecture eliminates power valve failure — a common issue with Holley-style carbs. The two-piece body design allows jet and rod changes without draining fuel or removing the carburetor. Whether you're building a weekend cruiser Corvette, a street/strip Silverado, or restoring a classic GMC, the 1405's 600 CFM flow rate is the sweet spot for street-driven V8s. Frequently Asked Questions Q: Will this fit my stock intake manifold? A: This carburetor has a standard square bore flange pattern. It fits stock 4-barrel square bore intake manifolds found on most 1960s-1980s GM V8 engines. If you have a spread bore intake (Quadrajet-style), you'll need a square bore to spread bore adapter plate. Q: Can I add an electric choke later? A: Yes. The iFJF 1478 Electric Choke Kit is a direct bolt-on upgrade that converts this manual choke carburetor to electric choke operation. Check our store for the 1478 kit. Q: What's the difference between the 1405 and 1406? A: The 1405 comes with a manual choke (cable-operated), while the 1406 has an electric choke. The 1405 is preferred by performance enthusiasts who want full control over cold-start enrichment, while the 1406 is ideal for daily drivers who want set-and-forget convenience. Q: Does this carburetor come pre-tuned out of the box? A: Yes, it comes with factory baseline jetting and metering rods calibrated for 600 CFM on typical street V8 engines. Fine-tuning may be needed based on your specific engine displacement, cam profile, altitude, and exhaust setup. Q: What gaskets and hardware are included? A: The carburetor includes the mounting gasket, fuel inlet fitting, and basic hardware. We recommend purchasing a quality intake manifold gasket set separately for your specific application. Q: Is this carburetor compatible with EGR systems? A: No — this carburetor does not have an EGR provision. It is designed for non-EGR performance applications or vehicles where the EGR system has been removed. For off-road and racing use only where emissions equipment removal is legal. Q: What horsepower range does 600 CFM support? A: A properly tuned 600 CFM carburetor can support 350-450 horsepower on typical street V8 engines. For engines exceeding 450 HP, consider stepping up to a 750 CFM unit. 🔗 Related Products from iFJF 1406 Performer 600 CFM Carburetor (Electric Choke) 1404 Performer 500 CFM Carburetor (Manual Choke) 1403 Performer 500 CFM Carburetor (Electric Choke) 1478 Electric Choke Kit for 1405/1406 📚 Helpful Installation Guides 📖 How To Rebuild Edelbrock 1406 and 1405 Carburetors | Rebuild Kit Links 📖 iFJF 1403 Performer 500 CFM 4-Barrel Carburetor Installation Guide
$419.99
iFJF TP3018 Fuel Filter for 2001-2016 Duramax 6.6L — Silverado/Sierra 2500HD 3500HD
TP3018 Fuel Filter — Premium Filtration for Duramax 6.6L Diesel (2001-2016) The iFJF TP3018 Fuel Filter is a direct-fit OEM replacement for 2001-2016 GM trucks equipped with the 6.6L Duramax diesel engine. Whether you're running an LB7, LLY, LBZ, LMM, LML — this filter delivers the 4-micron filtration performance your Bosch common-rail injectors demand. A single grain of sand-sized contaminant can score an injector nozzle — this filter prevents that. Available in 1-Pack ($49.99) or 2-Pack ($89.99 — save $10). The TP3018 is one of the most critical maintenance items on any Duramax. GM specifies replacement every 15,000 miles, but many owners change it every other oil change (10,000 miles) for extra protection — especially if you fuel up at high-traffic stations or run biodiesel blends. A clogged or bypassing fuel filter starves the CP3/CP4 injection pump of both fuel and lubrication, which can cause $4,000+ in injection system repairs. Key Features 4-Micron Absolute Filtration: Multi-layer cellulose/synthetic blend media captures 99.9% of particles at 4 microns — critical protection for high-pressure common rail injectors operating at 26,000+ PSI Built-In Water Separation: Hydrophobic media repels and coalesces water droplets, preventing corrosion and diesel bug (microbial growth) in your tank and fuel system Direct OEM Cross-Reference: Replaces ACDelco TP3018, TP3012, GM 12664429, 19305685 — exact dimensional match, guaranteed fit 15,000-Mile Service Life: Matches or exceeds GM's recommended fuel filter change interval Pre-Lubed Viton O-Ring: Every filter includes a fresh Viton seal — never reuse old O-rings, they shrink and leak Heavy-Duty Canister: Thick-gauge steel with corrosion-resistant coating stands up to road salt, moisture, and under-hood heat Vehicle Compatibility Year Make Model Engine 2001-2016 Chevrolet Silverado 2500HD / 3500HD 6.6L Duramax V8 (LB7, LLY, LBZ, LMM, LML) 2007-2016 GMC Sierra 2500HD / 3500HD 6.6L Duramax V8 2012-2016 Chevrolet Express 2500 / 3500 / 4500 6.6L Duramax V8 (LGH/LML) 2012-2016 GMC Savana 2500 / 3500 6.6L Duramax V8 (LGH/LML) Technical Specifications Specification Value Filter Type Spin-On Fuel/Water Separator Micron Rating 4 micron absolute / 10 micron nominal Thread Size M36 x 1.5 Height Approx. 6.5 inches Cross References TP3018, TP3012, 12664429, 19305685, 12633243 Service Interval 15,000 miles (normal) / 10,000 miles (severe duty) Replacement Guide Locate the fuel filter housing on the passenger side of the engine bay Place a drain pan underneath — expect 4-8 oz of diesel to spill Open the air bleeder screw to release pressure Spin off old filter counterclockwise (a filter wrench may be needed if overtightened) Lube the new filter's O-ring with clean diesel — do NOT use grease or oil Spin on hand-tight, then 1/4 turn with wrench — do NOT overtighten Prime the system: turn key to ON (not start) for 30 seconds, repeat 3-5 times until the primer pump is firm Start engine, check for leaks around the filter seal FAQ Q: Is this the same as the ACDelco TP3018? A: It matches the ACDelco TP3018 in fitment, thread size, and filtration rating. Our filter uses equivalent multi-layer media with the same 4-micron absolute rating — manufactured in an IATF 16949-certified facility. You get OEM-equivalent protection at aftermarket pricing. Q: What happens if I don't change my fuel filter on time? A: A clogged fuel filter restricts fuel flow to the injection pump. Symptoms include power loss under load, rough idle, hard starting, and in severe cases — CP3/CP4 pump cavitation and failure. The injection pump relies on diesel fuel for both cooling and lubrication. A restricted filter starves it of both. Injector replacement on a Duramax costs $3,000-$5,000. A $49.99 filter is cheap insurance. Q: Will this fit my 2001 LB7? A: Yes — this filter fits all Duramax engines from the original 2001 LB7 through the 2016 LML. The filter thread (M36 x 1.5) has been standard across all generations. Q: Can I use this filter with biodiesel (B5-B20)? A: Yes, compatible with ULSD and biodiesel blends up to B20. Note: biodiesel has stronger solvent properties — we recommend reducing your filter change interval to 10,000 miles when running biodiesel regularly, as it can loosen tank deposits that load the filter faster. Q: Why does my truck feel sluggish after the filter change? A: You likely have air in the system. Re-prime thoroughly — turn key to ON for 30 seconds (you should hear the lift pump run), repeat 3-5 times. If the primer pump on your housing never gets firm, the primer pump seals may be worn. Q: What's the difference between your TP3018 and the WIX equivalent? A: Our TP3018 uses a cellulose/synthetic blend media that balances filtration efficiency with flow rate — optimized for the Duramax's fuel demand under load. WIX 33960XE uses a full synthetic media. Both are quality filters; ours is priced $10-15 less per unit. Q: Should I buy the 2-pack? A: If you plan to keep your Duramax for more than one fuel filter change, the 2-pack saves you $10. Most Duramax owners change their fuel filter every 10,000-15,000 miles — the 2-pack covers 20,000-30,000 miles of driving. Keep the spare on your garage shelf. Q: Why is the TP3018 the most popular Duramax fuel filter?A: The TP3018 is the industry-standard fuel/water separator for GM Duramax 6.6L engines — with 1,300+ monthly searches and a 15.2% purchase rate among Duramax owners actively shopping. It's popular because: (1) It fits every Duramax generation from 2001 LB7 through 2016 LML, (2) The 4-micron absolute rating provides excellent common-rail injector protection, and (3) The built-in water separation media prevents the #1 cause of Duramax fuel system failures — water contamination. Every Duramax owner should keep a spare on the shelf. Q: What's the difference between TP3018 and TP3012?A: The TP3012 is an earlier GM part number that cross-references to the same filter specification. The TP3018 is the current ACDelco part number and what most parts stores stock. Both fit the same M36 x 1.5 thread on the 12642623 filter housing and have identical filtration ratings. Our TP3018 replaces both — order with confidence regardless of which number you're replacing. 📖 Related Guides 2001-2016 Duramax Diesel Fuel Filter Replacement: Complete DIY Guide Diesel Fuel Filter Maintenance — When to Replace Your Fuel/Water Separator 🔧 Complete Your Maintenance Fuel Filter Housing Assembly — related Duramax fuel system component Fuel Filter + Oil Filter Bundle — related Duramax fuel system component Filter Head Rebuild Kit — related Duramax fuel system component 12642623 Head + 1R-0750 Kit — related Duramax fuel system component
$49.99 - $89.99
iFJF 3952301 Oil Filter Adapter for Chevy SBC/BBC V8 — Billet Spin-On Conversion
3952301 Oil Filter Adapter — Spin-On Conversion for Chevy SBC/BBC V8 Ditch the messy canister oil filter on your classic Chevy V8 and convert to a modern spin-on system. The iFJF 3952301 Oil Filter Adapter replaces the factory bypass-style canister filter housing on small block Chevy (SBC) and big block Chevy (BBC) engines. CNC-machined from 6061-T6 billet aluminum with clear anodized finish — a permanent upgrade that makes every oil change faster, cleaner, and gives you access to modern synthetic filter media. Key Features Spin-On Conversion: Standard 13/16"-16 UNF threaded flange accepts Fram PH5, Wix 51060, AC Delco PF2, and hundreds of other spin-on filters. Bypass Compatible: Retains factory external bypass filtration system — safe for all SBC and BBC engines with original bypass oiling. Universal SBC/BBC Fit: Compatible with all small block Chevy (262-400ci) and big block Chevy (366-454ci) V8 engines using the factory canister-style filter housing. 6061-T6 Billet Aluminum: CNC-machined from solid billet — won't crack, warp, or leak like cast aluminum or pot metal adapters. Complete Kit: Includes adapter body, mounting gasket, grade 8 bolts, and thread sealant for a leak-free installation. Compatibility Engine Family Displacement (ci) Common Applications Small Block Chevy (SBC) 262, 265, 283, 302, 305, 307, 327, 350, 400 Camaro, Chevelle, Nova, C10, Corvette, Impala (1955-2002) Big Block Chevy (BBC) 366, 396, 402, 427, 454 Chevelle SS, Corvette, Caprice, C20/C30, Suburban Specifications Spec Value Part Number 3952301 Material 6061-T6 Billet Aluminum, Clear Anodized Thread Size 13/16"-16 UNF (Standard Spin-On) Gasket Type Fiber-Reinforced Rubber Recommended Torque 18-22 ft-lbs (Block Bolts) Benefits of Spin-On Conversion Faster Oil Changes: Spin off, spin on — no more wrestling with canister bolts and gaskets. Better Filter Availability: Fram PH5 and Wix 51060 filters available at every auto parts store nationwide. Modern Filter Media: Access to synthetic, high-flow, and extended-life filter options not available in canister style. Built-In Anti-Drainback: Most modern spin-on filters include an anti-drainback valve for faster cold-start oil pressure. Cleaner Installation: No more oil running down your arm when removing the canister housing. Installation Guide Drain engine oil completely. Remove factory canister filter housing and bypass valve assembly. Clean engine block mounting surface thoroughly — remove all old gasket material and oil residue. Apply included thread sealant to adapter bolts. Position gasket on adapter. Bolt adapter to engine block. Torque to 18-22 ft-lbs in a crisscross pattern. Pre-fill new spin-on filter with fresh oil. Apply thin film of oil to filter gasket. Spin filter onto adapter — hand-tighten, then additional 3/4 turn. Do NOT use a filter wrench to tighten. Refill engine with correct oil capacity (typically 4-5 quarts for SBC, 5-6 for BBC). Start engine, check oil pressure gauge, inspect adapter and filter for leaks. Frequently Asked Questions Q: Will this fit my 350 SBC with headers?A: Yes. The compact billet aluminum profile was specifically designed to clear most header configurations. The adapter adds minimal depth compared to the factory canister housing. Q: What oil filter should I use?A: The adapter accepts any filter with 13/16"-16 UNF thread. Popular choices: Fram PH5 (standard), Wix 51060 (premium), AC Delco PF2 (OEM), Mobil 1 M1-302 (synthetic extended-life). Q: Does this fit the 400 small block?A: Yes. The 400 SBC uses the same oil filter mounting boss and bypass configuration as all other small block Chevy engines. Direct bolt-on fit. Q: Will this work with an oil cooler adapter?A: Yes. The adapter has the standard SBC/BBC oil filter boss pattern. Most sandwich-style oil cooler adapters fit between the adapter and the spin-on filter. Q: Is this billet adapter better than cast aluminum options?A: Absolutely. Billet 6061-T6 aluminum is significantly stronger and more resistant to cracking than cast aluminum. It also machines to tighter tolerances for a leak-free seal. Worth the investment for a part you'll install once and forget. Q: Does this retain the factory bypass valve?A: This adapter is designed for engines with external bypass filtration. If your engine uses an internal bypass (some later SBC blocks), verify compatibility before ordering. The adapter itself does not include an internal bypass. Related Products More in Tools & Shop: Related Products 5184294AE Oil Filter Related Guides & Articles Diesel Fuel Filter Replacement: Complete Guide Complete Guide: How to Rebuild Edelbrock 1406 and 1405 Carburetors How to Replace the Serpentine Belt on a 5.9 & 6.7L Cummins 📖 Related Guide: Duramax CAT Oil Filter Adapter Guide: 7791 Conversion — Read our in-depth maintenance guide for step-by-step instructions.
$29.99
iFJF Thunder AVS 650 CFM Carburetor 4 Barrel Square Bore — Manual Choke Satin Finish 1805
Product Overview The iFJF 1805 Thunder AVS 650 CFM carburetor delivers classic muscle car performance with modern manufacturing precision. Featuring annular discharge boosters, manual choke operation, and a clean satin-finish aluminum body, it's the go-to upgrade for small block V8s from 283 to 400 cubic inches. Whether you're building a weekend cruiser, a street/strip car, or restoring a classic, the 1805 provides reliable fuel delivery and crisp throttle response. Key Features 650 CFM Airflow — The ideal CFM rating for street-driven small block V8s. Provides excellent throttle response without the low-speed drivability issues that plague oversized carburetors. Annular Discharge Boosters — Eight precision-drilled discharge holes per booster atomize fuel more effectively than single-point boosters, resulting in smoother idle, better part-throttle response, and improved fuel economy. Manual Choke — Simple, reliable cable-operated choke. No electrical connections, no vacuum diaphragms to fail. You control exactly when to engage and disengage. Two-Piece Aluminum Body — Die-cast aluminum construction with fewer gasket surfaces than three-piece designs means fewer potential leak points and greater durability. Square Bore Mounting — Direct bolt-on for most aftermarket 4-barrel intakes (Edelbrock Performer, RPM, Weiand, Holley) and factory square bore manifolds. Compatibility Engine Family Displacement Typical Applications Chevy Small Block 283, 305, 307, 327, 350, 383, 400 Camaro, Chevelle, Nova, C10, Impala, Monte Carlo Ford Small Block 289, 302, 351W Mustang, F-150, Bronco, Fairlane, Torino Mopar Small Block 273, 318, 340, 360 Charger, Challenger, Dart, Duster, Ram AMC V8 290, 304, 343, 360, 390, 401 Javelin, AMX, CJ-5, CJ-7, Wagoneer Buick/Olds/Pontiac 300-455 Square bore intake required (verify manifold pattern) Specifications Parameter Value Part Number 1805 CFM Rating 650 CFM Barrels 4-Barrel Square Bore Choke Manual Choke Booster Type Annular Discharge Primary Jet 0.095" Secondary Jet 0.098" Body Material Die-Cast Aluminum (Satin) Fuel Inlet 5/8"-20 Thread Why iFJF 1805 vs. OEM? Factory carburetors from the 60s-80s are now 40-60 years old. They suffer from warped castings, corroded passages, worn throttle shafts, and degraded accelerator pumps. Our 1805 is brand new — no core required, no rebuilding, no surprises. The annular boosters found on the Thunder AVS are a genuine upgrade over standard boosters, providing fuel atomization comparable to fuel injection at a fraction of the cost. Each unit is wet-flow tested and pre-calibrated for out-of-the-box performance. Frequently Asked Questions Q: Will this bolt onto a stock Chevy 350 intake manifold?A: Yes — as long as your intake manifold has a square bore flange pattern. Most 1966-and-later Chevy small block intakes are square bore. If you have a spread bore manifold (e.g., some Quadrajet applications), you'll need an adapter. Q: What's included in the box?A: Carburetor, base gasket, mounting studs/nuts/washers, and installation instructions. Q: Can I use this with an automatic transmission?A: Yes. The 1805 works with both automatic and manual transmissions. You'll need to connect your transmission's kickdown linkage (TH350/TH400/700R4) using the provided throttle lever. Q: How do I hook up the manual choke?A: Route a universal choke cable (not included) from the choke lever on the carburetor, through the firewall grommet, to a dash-mounted pull knob. Most auto parts stores carry universal choke cable kits for $10-20. Q: Will this work at high altitude (5,000+ ft)?A: At high altitude, you may need to lean the mixture. The 1805 accepts standard Edelbrock/Thunder-series jets and metering rods for calibration. For altitudes above 5,000 ft, go down 1-2 jet sizes.
$357.99
iFJF iFJF 1906 4 Barrel Carburetor for AVS2 Series 650CFM Carburetor Annular Booster Satin Finish Square Bore (Electric Choke)
High-Performance AVS2 Series 650CFM Carburetor The iFJF 1906 4-Barrel Carburetor brings legendary AVS2 performance technology to your engine build. Featuring the advanced annular flow booster design, this 650 CFM carburetor delivers exceptional fuel atomization for crisp throttle response and consistent power delivery. Whether you're upgrading a street cruiser, building a restomod, or preparing for weekend track days, the AVS2 platform provides the tunability and reliability that performance enthusiasts demand. The satin finish adds a premium look that complements any engine bay while providing enhanced corrosion resistance. Annular Booster Technology The defining feature of the AVS2 series is the annular discharge booster ring, which positions multiple fuel discharge ports around the entire circumference of each booster venturi. This design creates a finer fuel mist than traditional single-point boosters, resulting in more complete combustion, improved fuel economy at cruising speeds, and noticeably sharper throttle response. On the dyno, annular boosters have been shown to improve mid-range torque by 5-10 lb-ft compared to equivalent down-leg booster designs on a typical 350 CID small block. Vehicle Compatibility Engine Family Displacement Typical Vehicles Chevrolet Small Block V8 305 / 327 / 350 / 383 / 400 CID Camaro, Chevelle, Nova, Corvette, C10 Truck Ford Small Block V8 289 / 302 / 351W CID Mustang, Fairlane, F-100, Bronco Mopar Small Block 318 / 340 / 360 CID Dart, Duster, Charger, Challenger AMC V8 304 / 360 / 390 CID Javelin, AMX, Jeep CJ/FSJ Pontiac V8 326 / 350 / 389 / 400 CID Firebird, GTO, Grand Prix Technical Specifications Specification Detail CFM Rating 650 Barrels 4-Barrel Mounting Pattern Square Bore (4150-style) Choke Type Electric (12V) Booster Type Annular Discharge Fuel Inlet 3/8" NPT Secondaries Vacuum-Operated (Adjustable Air Valve) Finish Satin Aluminum Part Number 1906 SKU FJ-CBRT-1906 Key Features 650 CFM airflow rating - optimized for 300-400+ HP street performance engines Annular discharge boosters for superior atomization and throttle response Electric choke with fast-idle cam for reliable cold starts Adjustable vacuum secondary air valve - tune secondary engagement without removing carburetor Two-piece cast aluminum body with satin finish Compatible with both manual and automatic transmissions Accepts standard 5-1/8" air cleaner flange Frequently Asked Questions Q: What is the CFM rating and what engines does it support?A: The iFJF 1906 is rated at 650 CFM, making it ideal for small-block V8 engines between 305 and 400 cubic inches. It is perfectly suited for 327, 350, 383, and 400 CID engines in street performance and mild racing applications. Q: What does the annular booster design do?A: The annular discharge booster design provides superior fuel atomization compared to traditional down-leg boosters. This results in improved throttle response, better fuel economy at cruise, and more consistent air-fuel mixture across all RPM ranges. Q: Does this carburetor come with an electric choke?A: Yes, the iFJF 1906 features an integrated electric choke for reliable cold starts. Simply connect to a 12V ignition-switched power source and the choke will automatically adjust based on engine temperature. Q: Is this a square bore or spread bore carburetor?A: This is a square bore (4150-style) carburetor designed to bolt directly onto square bore intake manifolds. It can also be used with spread bore manifolds using an adapter plate (sold separately). Q: What is the satin finish and why does it matter?A: The satin finish is a premium aesthetic treatment that provides a semi-gloss, non-reflective surface. It resists fuel stains and corrosion better than raw aluminum while maintaining a classic performance look that complements any engine bay. Q: Is tuning required out of the box?A: The carburetor comes with baseline calibration suitable for a typical 350 CID engine at sea level. Minor adjustments to idle mixture screws, accelerator pump, and possibly jet changes may be needed based on your specific engine combination, elevation, and performance goals. Q: What makes this different from the standard AVS series?A: The AVS2 series features the upgraded annular flow booster design, improved fuel metering circuits, and a revised air valve system that provides more precise secondary engagement compared to the original AVS design, resulting in smoother power delivery and better mid-range torque. Related Products More in Small Engines & Carburetors: DR-Z125L Part 08P502 Part 699915 Part Blog Resources Carburetor Tuning & Installation Guides iFJF Performance News & Updates
$419.99
iFJF EGR Valve Block Off Plate for 1988-1995 Chevy/GMC C1500 C2500 C3500 — 4.3L-5.7L
Product Overview This iFJF EGR Valve Block Off Plate provides a precision-machined solution for permanently sealing the EGR port on 1988-1995 GM small-block V8 and 4.3L V6 engines. CNC-cut from a solid billet of 6061-T6 aluminum, it replaces the factory EGR valve with a rigid, leak-free seal — purpose-built for off-road and racing applications where the EGR system has been removed. Key Features CNC-Machined 6061-T6 Billet Aluminum — Aircraft-grade aluminum won't warp, crack, or deform under heat cycling. At 0.375" thick, it's over 3x thicker than typical stamped steel universal plates. Precision Fit for GM Small-Block & 4.3L V6 — Bolt pattern matches the GM EGR valve flange exactly. No grinding, filing, or adapter plates needed. Leak-Free Seal — CNC-machined flat to tight tolerances for a perfect mating surface. Pair with a standard OEM EGR mounting gasket (GM #10108435, sold separately) for a vacuum-tight seal. Corrosion-Resistant — Natural 6061-T6 aluminum finish. Won't rust like steel block-off plates. Compatible with paint or anodizing if desired. GMT400 Platform Coverage — Fits 1988-1995 C/K 1500/2500/3500 pickups, Blazer, Tahoe, Yukon, Suburban, plus Camaro and Caprice passenger cars. Compatibility Make Model Years Engine Chevrolet / GMC C1500 / C2500 / C3500 1988-1995 4.3L V6 / 5.0L V8 / 5.7L V8 Chevrolet / GMC K1500 / K2500 / K3500 1988-1995 4.3L V6 / 5.0L V8 / 5.7L V8 Chevrolet / GMC Blazer / Tahoe / Yukon 1992-1995 5.0L V8 / 5.7L V8 Chevrolet / GMC Suburban 1988-1995 4.3L V6 / 5.0L V8 / 5.7L V8 Chevrolet Camaro 1988-1997 5.0L V8 / 5.7L V8 Chevrolet Caprice / Impala 1989-1995 4.3L V6 / 5.0L V8 / 5.7L V8 Chevrolet S10 Blazer / Astro Van 1985-1994 2.5L L4 / 2.8L V6 / 4.3L V6 Specifications Specification Detail Part Number IFJF-GM-EGR-BOP Material 6061-T6 Billet Aluminum Thickness 0.375" (3/8") Finish Natural aluminum (CNC machined) Manufacturing CNC machined — not stamped or cast Application Off-road / race track use only Gasket Use OEM EGR mounting gasket (sold separately) Why Choose iFJF? Thin stamped plates warp. Cast plates crack. Our block-off plates are CNC-machined from a solid billet of 6061-T6 — the same aluminum grade used in aerospace structural components. Every plate is inspected for flatness before shipping. If you're building a serious off-road truck, trail rig, or race vehicle, don't trust your intake manifold seal to a $5 universal plate. ⚠️ Warning: This device is intended for off-road / race track use only. Removing or disabling emission control equipment on vehicles operated on public roads violates federal law. The purchaser assumes full responsibility for compliance with applicable regulations. Installation Notes Remove the factory EGR valve from the intake manifold (typically 2 bolts). Clean the intake manifold mounting surface thoroughly. Remove all old gasket material — a razor scraper works best. Place a new OEM EGR mounting gasket on the manifold flange. We recommend GM part #10108435 or equivalent. Position the block-off plate over the gasket and install the factory bolts. Torque to 18-22 ft-lbs (M8 bolts). Important: To prevent the ECU from triggering a Check Engine Light, pair this plate with an EGR delete simulator or ECU tune (sold separately). This plate seals the mechanical port only — it does not address the electrical side. Frequently Asked Questions Q: What engines does this EGR block off plate fit?A: Fits 1988-2000 GM small-block V8 & 4.3L V6 engines including 5.0L (305), 5.7L (350), and Vortec L31. Covers C1500-C3500, K1500-K3500, Blazer/Tahoe/Yukon, Suburban, and Camaro/Caprice. Does NOT fit 7.4L (454) big block. Q: Do I need a gasket with this block-off plate?A: Yes — use a new OEM EGR mounting gasket (GM #10108435 or equivalent, sold separately). The CNC-flat surface mates perfectly with any standard EGR gasket for a vacuum-tight seal. Q: Will a block-off plate alone keep my Check Engine Light off?A: No. The plate only seals the mechanical EGR port. The ECU will detect the missing EGR valve and trigger codes P0401/P0404 (OBD-I codes 32/53). You need an EGR delete simulator or ECU tune for the electrical side. Q: Is this CARB-legal for on-road use in California?A: No — this product is intended exclusively for off-road, racing, and competition vehicles that are never operated on public highways. Not CARB-compliant. Purchaser assumes full responsibility for emissions compliance. Q: Billet aluminum vs stamped steel — what's the real difference?A: Stamped steel plates (~0.120") warp and develop vacuum leaks. Our 0.375" CNC-machined 6061-T6 billet plate is 3x thicker with a precision flat sealing surface. No warping, no leaks, no comparison. Related Products EGR Delete Kit — 1.9TDI Diesel L5P Duramax CAN Bus Plugs L5P EGR Delete Kit — Duramax Related Blog Posts EGR Delete: What You Need to Know Diesel Engine Maintenance 101
$34.99
iFJF 20833606 Driver Side Interior Door Handle for Chevy Silverado/GMC Sier
Product Overview The iFJF 20833606 Driver Side Interior Door Handle for Chevy Silverado/GMC Sierra 1500 25 is a high-quality aftermarket replacement part designed for 2083-2087 Chevy, GMC, Sierra models. This direct-fit component meets or exceeds OEM specifications at a fraction of dealer pricing. Backed by iFJF's commitment to quality and US-based customer support. Key Features Premium Construction — Manufactured from high-grade materials selected for durability and performance in demanding applications. Direct Fit Design — Precision-engineered to match factory mounting points, connectors, and specifications. No modifications, cutting, or fabrication required. OEM-Spec Performance — Designed to meet or exceed original equipment specifications for reliable, consistent operation. Easy Installation — Bolt-on or plug-and-play design for straightforward DIY installation with basic hand tools in most applications. Quality Assurance — Every iFJF part undergoes rigorous quality inspection before shipping to ensure perfect fit and function. Compatibility Designed for 2083-2087 Chevy, GMC, Sierra vehicles and equipment. Please verify your specific model year and engine configuration before ordering. Contact our support team if you need assistance confirming fitment for your application. Specifications Specification Details Brand iFJF Fitment 2083-2087 Chevy, GMC, Sierra Condition New Installation Direct Replacement Why Choose iFJF iFJF is a trusted supplier of aftermarket auto parts, diesel performance components, and powersports accessories. We source directly from ISO-certified manufacturers and stand behind every product with responsive US-based customer service. Save money vs. dealer pricing without compromising on quality or fit. Frequently Asked Questions Q: Will this fit my 2083-2087 Chevy, GMC, Sierra model?A: This part is designed for 2083-2087 Chevy, GMC, Sierra. Please check the compatibility information above and confirm your exact year, make, model, and engine before ordering. Contact us with your VIN for a fitment guarantee. Q: Is this an OEM part?A: This is a high-quality aftermarket replacement manufactured to meet or exceed OEM specifications. It offers the same fit and function as the original at a significantly lower cost. Q: What's included in the package?A: The package includes the 20833606 Driver Side Interior Door Handle for Chev as shown in the product images. Any additional hardware, gaskets, or accessories are shown in the listing photos. Q: Is professional installation required?A: Installation difficulty varies by application. Most customers complete installation with basic mechanical skills and common hand tools. Professional installation is always recommended if you're unsure. Q: What is the warranty?A: iFJF products come with a warranty against manufacturing defects. Please retain your order information and contact our support team if you experience any issues. Q: How fast is shipping?A: Orders typically ship within 1-2 business days from our US warehouse. Free shipping is available on orders $50+. Expedited shipping options are available at checkout.
$49.99
iFJF 2013-2014 Dodge Ram 6.7L Cummins EGR Delete Kit w/ Cooler & Throttle Valve Delete + 4" Exhaust Pipe - 3500/4500/5500 Cab & Chassis
Product Overview Upgrade your 2013-2014 Dodge Ram 6.7L Cummins with this professional-grade egr delete + cooler delete + throttle valve delete + exhaust pipe. Designed for the Ram 3500/4500/5500 Cab & Chassis, this kit delivers improved engine performance, reduced maintenance issues, and enhanced reliability. Whether you're a professional diesel mechanic or a DIY enthusiast, our precision-engineered components provide a bolt-on solution for your Dodge Ram truck. ⚠️ Off-Road Use Only: This product is intended for off-road and competition use only. Please check your local, state, and federal regulations before purchasing and installing emissions-related components. Key Features Precision Fit: Engineered specifically for 2013-2014 Dodge Ram 6.7L Cummins Ram 3500/4500/5500 Cab & Chassis — direct bolt-on installation with no modifications required. Heavy-Duty Construction: Built with industrial-grade materials to withstand extreme temperatures and pressures in high-performance diesel applications. Complete Kit: Includes all necessary hardware — gaskets, bolts, block-off plates, and installation components for a straightforward install. Performance Gains: Eliminates common failure points in the OEM EGR/exhaust system, improving exhaust flow, reducing EGTs (Exhaust Gas Temperatures), and enhancing throttle response. Corrosion Resistant: All components feature corrosion-resistant finishes to withstand road salt, moisture, and extreme weather conditions. Compatibility Year Make Model Engine 2013 Dodge/Ram 3500/4500/5500 Cab & Chassis 6.7L Cummins Diesel 2014 Dodge/Ram 3500/4500/5500 Cab & Chassis 6.7L Cummins Diesel Why Choose iFJF Direct? Quality Assurance: Every component undergoes rigorous quality control inspection before shipping. Expert Support: Our diesel specialists know 6.7L Cummins trucks inside out — installation help is just a message away. Frequently Asked Questions Q: Is this kit compatible with my 2013 Dodge Ram Ram 3500/4500/5500 Cab & Chassis?A: Yes! This kit is designed as a direct bolt-on for 2013-2014 Dodge Ram 6.7L Cummins Ram 3500/4500/5500 Cab & Chassis. No modifications are required for installation on stock vehicles. Q: What tools do I need for installation?A: Basic hand tools including socket set (8mm-19mm), torque wrench, flathead and Phillips screwdrivers, and penetrating oil for rusted fasteners. Most experienced DIY mechanics can complete the installation in 2-4 hours. Q: Will this delete kit trigger a check engine light (CEL)?A: This is a hardware-only kit. For complete functionality, appropriate ECU tuning is recommended to prevent DTCs (Diagnostic Trouble Codes). Professional tuning services are available from third-party providers. Q: Are gaskets and hardware included?A: Yes — all necessary gaskets, bolts, block-off plates, and mounting hardware are included in the kit. We recommend having replacement exhaust manifold gaskets on hand if your vehicle has high mileage. Q: How does this compare to OEM parts?A: Our components are engineered to solve the known failure points in the OEM emissions system. By eliminating problematic EGR coolers, valves, and restrictive exhaust components, you'll experience improved reliability, better fuel economy, and reduced maintenance costs. Q: What material are the block-off plates made from?A: Block-off plates are CNC-machined from 6061-T6 billet aluminum (or 304 stainless steel where noted) — far superior to OEM cast components that are prone to cracking and leaking under heat cycling. Q: Do you offer a warranty?A: Yes! All iFJF Direct products come with a satisfaction guarantee. If you have any issues with fitment or quality, contact our support team for a replacement or refund. What's in the Box 4" exhaust tube / pipe (main delete pipe) EGR block-off plates (CNC-machined 6061-T6 billet aluminum) Cooler delete bypass components Throttle valve delete plate Gaskets, bolts & mounting hardware Note: Connecting clamps are NOT included — reuse your existing clamps or order separately to avoid installation delays. Compare & Choose Your Delete Kit Same 6.7L Cummins platform — pick the package that fits your truck and budget: Complete Kit (This Product) — EGR + Cooler + Throttle Valve Delete + 4" Exhaust Pipe. Everything in one box for the 2013-2014 Ram 3500/4500/5500 Cab & Chassis. View Complete Kit EGR + Cooler + Throttle Valve Delete Only — Same three deletes without the exhaust pipe, for 2013-2014 Cab & Chassis. View 3-Piece Kit EGR Delete Only — Budget EGR block-off plate kit for 2013-2018 Ram 3500/4500/5500 Cab & Chassis. View EGR-Only Kit 2013-2018 Full Kit — Same complete delete package covering the wider 2013-2018 model years. View 2013-2018 Kit iFJF 2013-2018 6.7L Dodge RAM 2500 3500 Cummins Diesel EGR Delete Cooler Throttl iFJF 2013-2018 6.7L Dodge Ram 2500 3500 Turbo Diesel Generic 4'' Exhaust Tube Pi
$379.00$317.08