Search results for "Pool Cleaner Parts"

NOx Nitrogen Oxide Sensor 5WK96681D — OEM-Grade Emissions Control Replacement The iFJF NOx Sensor 5WK96681D is a direct plug-and-play replacement for your vehicle's factory nitrogen oxide sensor. Engineered to meet or exceed OEM specifications, this sensor restores proper DEF/SCR system function, eliminates check engine lights triggered by NOx sensor fault codes, and helps your diesel engine pass emissions testing. What a NOx Sensor Does Nitrogen Oxide (NOx) sensors monitor the concentration of harmful nitrogen oxides in your diesel exhaust stream — both before and after the Selective Catalytic Reduction (SCR) catalyst. The engine control module (ECM) uses this data to precisely meter Diesel Exhaust Fluid (DEF) injection. When a NOx sensor fails, the ECM can't regulate DEF dosing properly, leading to increased emissions, reduced fuel economy, and potential limp-mode activation. Key Features OE-Equivalent Performance — Calibrated to match the voltage curve and response time of the factory sensor for seamless ECM integration. Plug-and-Play Installation — Pre-terminated connector matches factory wiring harness. No splicing, no programming — remove the old sensor and install the new one. Durable Construction — High-temperature ceramic sensing element with stainless steel probe body withstands exhaust temperatures up to 930°C (1,700°F). Clears NOx-Related Fault Codes — Resolves common DTCs related to NOx sensor performance, circuit range, and rationality errors. 12-Month Warranty — Backed by iFJF's quality guarantee against manufacturing defects. Compatibility Make Models Engine Mercedes-Benz E250 BlueTEC 2.1L Diesel Freightliner Sprinter 2500, 3500 3.0L V6 Diesel Mercedes-Benz GLK250 BlueTEC 2.1L Diesel Cross-Reference / OEM Part Numbers Manufacturer Part Number(s) Mercedes-Benz A0009055100, A0009053403 Continental/VDO 5WK96681D Specifications Sensor Type Nitrogen Oxide (NOx) Sensor Model 5WK96681D Connector Type Pre-Terminated Factory Match Probe Material Stainless Steel with Ceramic Element Operating Temperature Up to 930°C (1,700°F) Installation Plug-and-Play (No Programming) Warranty 12 Months Symptoms of a Failing NOx Sensor Check Engine Light (CEL/MIL) — Common fault codes: P2200-P2214 (NOx sensor circuit), P229E/P20EE (SCR NOx efficiency) Failed Emissions Test — Vehicle produces excessive NOx emissions during inspection Increased DEF Consumption — ECM overcuts DEF trying to compensate for bad sensor readings Reduced Fuel Economy — Engine may run in a less efficient mode when NOx sensor data is unreliable Limp Mode / Reduced Power — In severe cases, the ECM may limit engine power to protect the emissions system Frequently Asked Questions Do I need to reprogram the ECM after installing this sensor? No — this is a plug-and-play sensor. The ECM will automatically recognize the new sensor on the next key cycle. However, you may need to clear existing fault codes with an OBD-II scanner. Some vehicles require a short drive cycle (10-20 miles) for the sensor to fully calibrate and for readiness monitors to set. How do I know if my NOx sensor needs replacement? The most common indicators are: (1) check engine light with NOx-related DTCs, (2) failed emissions test with high NOx readings, and (3) visible physical damage to the sensor or wiring harness. A professional diesel shop can confirm the diagnosis with a scan tool by comparing upstream and downstream NOx readings. What's the difference between upstream and downstream NOx sensors? Upstream (pre-SCR) sensors measure NOx entering the catalyst. Downstream (post-SCR) sensors measure NOx exiting the catalyst. They may look identical physically but are typically calibrated differently. Verify your vehicle's exact position before ordering. Can a bad NOx sensor cause DEF system problems? Yes — the ECM relies on NOx sensor data to calculate DEF injection rates. A faulty sensor sending incorrect data can cause over-injection (wasting DEF fluid) or under-injection (failing emissions standards). Either scenario can trigger additional fault codes. How long should a NOx sensor last? Factory NOx sensors typically last 80,000-150,000 miles depending on driving conditions. Contaminated DEF fluid, excessive idling, and high-sulfur fuel can significantly reduce sensor life. If one sensor has failed, the others on the vehicle may not be far behind.

Read more less

Product Overview The AC Vent Outer Ring Trim Air Conditioning is a premium aftermarket replacement part precision-engineered to meet or exceed OEM specifications. Designed specifically for Camaro 2016-2019 (2016, 2017, 2018, 2019), this direct-fit component delivers reliable performance and straightforward installation — ideal for professional technicians and DIY mechanics alike. Key Features OEM-Spec Construction: Precision-engineered to match original equipment dimensions and performance standards — installs without modification. Durable Materials: Manufactured using high-grade materials selected for excellent wear resistance, corrosion protection, and long service life. Direct Fit Design: Drop-in replacement that matches factory mounting points, connectors, and clearances exactly. Quality Tested: Each unit undergoes thorough inspection and testing before shipment to ensure consistent, reliable performance. Exceptional Value: Matches dealer-part quality at a significantly lower cost — keep your vehicle running right without breaking the bank. Compatibility This ac parts is engineered to fit the following vehicles. Always verify using your VIN or existing OEM part number before ordering. Vehicle Year Range Fitment Camaro 2016-2019 Direct Fit Specifications Specification Detail Brand iFJF Direct Condition New Category AC Parts Warranty 1-Year Limited Why Choose iFJF Direct? iFJF Direct specializes in premium aftermarket replacement parts that deliver OEM quality without the dealer price tag. Every product is backed by our commitment to accurate fitment, responsive US-based customer support, and fast shipping from our warehouse. Whether you're maintaining a daily driver, restoring a classic, or repairing a fleet vehicle — we're here to help you get the job done right the first time. Installation Guidance Before You Begin: Verify compatibility using your vehicle VIN or existing OEM part number. Clean Work Area: Remove debris, rust, or old gasket material from mating surfaces before installation. Use Proper Tools: Refer to your vehicle's factory service manual for recommended tools and torque specifications. Safety First: Always disconnect the battery before working on electrical components. Wear safety glasses and gloves. Professional Installation: While many of our parts are DIY-friendly, we recommend professional installation if you're unsure about the procedure. Q: Is this a direct replacement for the OEM part?A: Yes, this AC Vent Outer Ring Trim Air Conditioning is manufactured to OEM specifications for exact fitment and function. No modifications are required for installation on compatible vehicles. Q: How do I verify this fits my vehicle?A: Check your existing OEM part number against the replacement numbers listed in the description. You can also use the year/make/model fitment guide above or contact our support team with your VIN. Q: What is the warranty period?A: This part is covered by a 1-year limited warranty against manufacturing defects. If you experience any issues, contact us for a free replacement or full refund. Q: How quickly will my order ship?A: Most orders ship within 1-2 business days from our US warehouse. Domestic delivery typically takes 3-7 business days. Tracking information is provided as soon as your order ships. Q: What is your return policy?A: We offer a 30-day hassle-free return policy. If the part doesn't fit or you're not satisfied, return it in original condition for a full refund. We stand behind every product we sell. Q: How does the quality compare to the dealership part?A: Our aftermarket parts match OEM specifications in material, fit, and performance. You get the same quality and reliability at a significantly lower price — without the dealership markup. Order With Confidence Get your vehicle back on the road with the AC Vent Outer Ring Trim Air Conditioning from iFJF Direct. Premium quality, fast shipping, and expert support — all backed by our satisfaction guarantee. Add to cart now and experience the iFJF Direct difference.

Read more less

Product Overview The iFJF Complete Fuel Filter Housing Kit is the all-in-one solution for rebuilding the fuel filter assembly on 1983-1994 Ford 6.9L and 7.3L IDI diesel engines. This comprehensive kit includes the housing header (F2TZ-9B249-A), heater element (F2TZ-9J294-A), and the bottom lower cap — everything needed to completely refresh your IDI fuel filtration system in one purchase. Key Features All-in-One Complete Kit: Includes housing header, heater element, and bottom lower cap — the three key components of the IDI fuel filter assembly in one box. Full OEM Compatibility: Replaces Ford F2TZ-9B249-A (header), F2TZ-9J294-A (heater), and E8TZ-9B249-A. Interchangeable with factory parts. 1983-1994 IDI Coverage: Fits all 6.9L and 7.3L IDI naturally aspirated engines — F150 through F350, Super Duty, Econoline vans, and F59 chassis. Corrosion-Resistant Aluminum: Upgraded aluminum construction resists rust and diesel fuel corrosion far better than the original steel components. Important Fitment Note: The F2TZ-9J294-A heater element is designed for naturally aspirated IDI engines. Not compatible with 1993 F250 7.3L turbo diesel (newer model). Verify your engine type before ordering. Specifications Specification Detail Part Number FJ-FORD04-ZH3 OEM Reference F2TZ-9B249-A, F2TZ-9J294-A, E8TZ-9B249-A Engine 6.9L IDI / 7.3L IDI (Naturally Aspirated Only) Material Aluminum Housing, Metal Heater Element Includes Housing Header, Heater Element 9J294, Bottom Lower Cap Fits F150 F250 F350 Super Duty E150 E250 E350 F59 1983-1994 Note Not for 1993+ 7.3L Factory Turbo Diesel Warranty 12-Month Warranty Why Choose iFJF? The IDI fuel filter assembly is one of the most failure-prone components on these aging diesel trucks. Corrosion, cracked housings, failed heater elements, and leaking caps all introduce air into the fuel system — causing hard starts, stalling, and power loss. Our complete kit replaces all three problem components at once for true peace of mind. Frequently Asked Questions Q: What does this complete kit include?A: The housing header, heater element (F2TZ-9J294-A), and the bottom lower cap — all three key components of the fuel filter assembly. Q: Will this fit my 1990 F350 7.3L IDI?A: Yes. Direct fit for all 1988-1994 7.3L IDI naturally aspirated diesel engines. Q: Why does it not fit the 1993 F250 7.3L Turbo?A: The factory turbo IDI (introduced 1993) used a different fuel filter configuration in some models. This kit is for naturally aspirated IDI engines. If you have a factory turbo, verify your filter base before ordering. Q: Is this a complete fuel filter replacement?A: This kit replaces the housing assembly — not the filter element itself. The fuel filter cartridge is sold separately and screws into this housing. Q: What are the symptoms that I need this kit?A: Fuel leaks at the filter assembly, air in fuel lines (engine sputters/stalls), diesel smell under hood, hard cold starts, and a non-functional fuel heater. Q: Installation difficulty?A: Intermediate. Requires basic hand tools and fuel line wrenches. Purge the fuel system after installation. Budget 1-2 hours. Q: How is this different from the FJ-FORD04-ZH1?A: The ZH3 includes the bottom lower cap in addition to the header and heater — making it the most complete kit available.

Read more less

FF5706 Fuel Filter for Cummins ISF 2.8L & 3.8L Diesel Engines The FF5706 fuel filter is engineered for Cummins ISF 2.8L and ISF 3.8L diesel engines in light-duty commercial trucks, buses, and industrial equipment worldwide. 20-micron filter replaces 5262311, 5283169, P555706, FP4001, and 2P0127177. Key Features ISF Engine Specific: Engineered for Cummins ISF 2.8L (ISF 160) and ISF 3.8L — common in Foton, JAC, and global light commercial vehicles. 20 Micron Filtration: Optimized for ISF fuel system requirements — balances contaminant removal with flow rate for these smaller-displacement diesels. OEM Cross Reference: Direct replacement for Cummins 5262311, 5283169, Fleetguard P555706, and Donaldson FP4001. IATF 16949 Certified: Consistent manufacturing quality with full batch traceability and 100% testing. Global Platform Support: Used in light trucks, buses, generators, and construction equipment worldwide. Technical Specifications Specification Value Part Number FF5706 / P555706 OEM Numbers 5262311, 5283169, 2P0127177 Filtration 20 Micron Nominal Engine Cummins ISF 2.8L / ISF 3.8L Aftermarket Cross FP4001 (Donaldson), FF5706 (Fleetguard) Vehicle & Engine Compatibility Engine Variant Application Cummins ISF 2.8L ISF 160 Light Trucks, Vans, Buses Cummins ISF 3.8L ISF 140/160/170 Medium Trucks, Industrial Why Choose This Product?The Cummins ISF platform powers millions of commercial vehicles globally. Using the correct fuel filter is critical — the ISF's common rail system operates at high pressure and even minor contamination causes injector wear. The FF5706 is purpose-built with the exact micron rating and flow characteristics specified by Cummins. Frequently Asked Questions Q: What vehicles use the Cummins ISF 2.8L engine?A: The ISF 2.8L (ISF 160) is used in Foton Tunland, JAC Shuailing, and various light commercial trucks primarily in Asian, South American, and African markets. Q: Is this a genuine Fleetguard filter?A: This is an iFJF aftermarket filter manufactured to meet or exceed Fleetguard FF5706 specifications. IATF 16949 certified and 100% tested. Q: What micron rating does the ISF engine require?A: The ISF 2.8L and 3.8L fuel systems require 20-micron filtration for the primary fuel filter. Using a 10-micron filter can cause excessive restriction. Q: How often should I replace this filter?A: Cummins recommends every 15,000 km (10,000 miles) under normal conditions. Reduce to 10,000 km in dusty environments or with lower-quality fuel. Order your iFJF replacement part today and experience the quality difference. Fast shipping from our US warehouse.

Read more less

Complete Performance Package: 3.5" Downpipe + EGR Delete Kit for 2017-2023 Duramax L5P Transform your 2017-2023 Chevrolet Silverado or GMC Sierra 2500HD/3500HD with the 6.6L Duramax L5P Turbo Diesel using this comprehensive performance package. This kit combines two essential L5P upgrades — a 3.5" mandrel-bent turbo downpipe and a complete EGR cooler & valve delete kit — into one complete package. Address both exhaust restriction and intake contamination simultaneously for maximum performance gains and long-term engine reliability. Package Contents 3.5" Turbo Downpipe T409 mandrel-bent stainless steel — maintains full 3.5" internal diameter V-band turbo flange for precision leak-free connection OEM hanger points — true bolt-on installation Replaces restrictive factory flattened downpipe 30-50% backpressure reduction at turbo outlet EGR Cooler & Valve Delete Kit CNC-machined 6061-T6 billet aluminum construction EGR cooler block-off plates (intake + exhaust sides) EGR valve delete plate with OEM-spec MLS gaskets Coolant reroute fittings — proper flow path maintained Complete Grade 10.9 hardware kit included Vehicle Compatibility Year Make Model Engine 2017-2023 Chevrolet / GMC Silverado 2500HD / Sierra 2500HD 6.6L Duramax L5P V8 Turbo Diesel 2017-2023 Chevrolet / GMC Silverado 3500HD / Sierra 3500HD 6.6L Duramax L5P V8 Turbo Diesel Why This Combo Package? The L5P Duramax has two critical factory restrictions that limit performance and reliability: the pinched downpipe creating excessive turbo backpressure, and the EGR system causing progressive intake carbon fouling. Addressing either alone provides benefits, but addressing both simultaneously delivers transformative results: Unrestricted Exhaust Flow: 3.5" mandrel-bent downpipe eliminates the single most restrictive point in the L5P exhaust — the flattened factory downpipe. Clean Intake Air: EGR delete prevents carbon accumulation on intake valves, swirl flaps, and manifold — preserving airflow and power for the life of the engine. Synergistic Gains: Cleaner intake charge + freer exhaust flow = 25-40 HP combined potential with supporting calibration. Maximum Reliability: Eliminates both EGR cooler failure risk (coolant in cylinders) and high-EGT conditions caused by exhaust restriction. Cost-Effective: Bundle pricing saves 15-20% compared to purchasing downpipe and EGR delete kit separately. Premium Build Quality T409 Stainless Steel Downpipe: Mandrel-bent for consistent internal diameter — no crush bends, no flow restrictions. CNC Billet 6061-T6 Aluminum EGR Plates: Precision-machined for exact L5P port matching. Anodized finish for corrosion resistance. MLS (Multi-Layer Steel) Gaskets: Rated for L5P boost pressures exceeding 35 PSI — no leaks, no failures. Grade 10.9 Mounting Hardware: High-tensile fasteners engineered for diesel vibration and thermal cycling. Performance Benefits +25-40 HP / +50-80 lb-ft Torque: Combined effect of reduced backpressure and clean intake air with proper tuning. 100-200°F Lower EGTs: Critical safety improvement for towing heavy loads up long grades. Faster Turbo Spool: Immediate throttle response improvement from reduced exhaust restriction. Eliminated Carbon Buildup: No more EGR soot fouling intake valves and manifold — preserved airflow forever. No Coolant Loss Risk: EGR cooler failure permanently eliminated — protects head gaskets and rotating assembly. 1-3 MPG Fuel Economy Gain: Combined efficiency improvement from both modifications. Installation Overview This comprehensive package requires significant disassembly — the downpipe is accessed from underneath, while EGR delete requires intake manifold removal from above. Estimated total installation time: 8-12 hours. Professional installation strongly recommended. Compatible tuning solution required for EGR delete function. All necessary hardware, gaskets, clamps, and fittings are included. No welding or permanent modifications needed. Frequently Asked Questions Q: Will this fit my 2020 Silverado 3500HD L5P?A: Yes. This combo kit fits all 2017-2023 Chevrolet Silverado 2500HD/3500HD and GMC Sierra 2500HD/3500HD with the 6.6L Duramax L5P engine. All cab and bed configurations supported. Q: Do I need a tuner with this kit?A: Yes. A compatible tuning solution is required to disable EGR-related DTCs and optimize engine parameters for the modified exhaust and intake configuration. For maximum performance benefit, a comprehensive tune addressing both modifications is recommended. Q: Can the downpipe and EGR delete be installed at different times?A: Yes, each component can be installed independently. However, installing both simultaneously saves significant labor time since the intake removal (for EGR) and under-vehicle access (for downpipe) involve related disassembly steps. Most shops recommend doing both at once. Q: Is this kit reversible?A: Both the downpipe and EGR delete kit are bolt-on designs with no cutting, welding, or permanent modifications. The factory components can be reinstalled. Tuning will need to be restored to stock as well. Q: How does this compare to buying the downpipe and EGR delete separately?A: The combo kit provides identical components at a bundled price — typically 15-20% savings versus purchasing individually. All hardware, gaskets, and fittings are identical to the standalone kits. Q: Will I need a wheel alignment after installation?A: No — neither the downpipe nor the EGR delete kit affect suspension geometry. A wheel alignment is not required. Q: Is this product intended for on-road use?A: This product is designed for off-road and competition use only. Not intended for vehicles subject to emissions regulations. Check local and state laws before purchase. Related Products for Your L5P Duramax L5P EGR Delete Kit (Standalone)EGR valve & cooler delete only L5P 3.5" Downpipe (Standalone)Downpipe-only option Duramax Fuel Filter1R-0750 replacement Related Blog Posts L5P Duramax Ultimate Performance Guide: Downpipe, EGR & Tune L5P Duramax Common Problems & Reliability Upgrades Duramax Tuning Guide: Stage 1, 2, and 3 Upgrade Paths ⚠️ Off-Road / Competition Use Only: This product is intended for off-road or competition vehicles only. Not legal for highway use on emissions-controlled vehicles in the US and many other jurisdictions. Check local and federal regulations before purchasing. Removal of emissions equipment may void your vehicle warranty. 🔗 Duramax Diesel Resources & Maintenance 📖 Related Guides: L5P Duramax Fuel Filter Housing Cap Replacement — Complete DIY Guide Duramax Fuel Filter Housing: Compatibility Guide (2001–2024) Duramax 6.6L Oil Change: Complete DIY Guide (Every Generation) 🔍 Shop All Duramax 6.6L Parts → | EGR Delete Parts → | Exhaust System →

Read more less

Product Overview The 2-Pack FS1098 Fuel Water Separator for Cummins B6.7 / ISL8.9 delivers professional-grade fuel filtration for diesel engines. Manufactured with advanced synthetic media for superior contaminant capture and water separation, this filter protects your high-pressure common rail injection system from the microscopic particles and moisture that cause premature injector and pump failure. As diesel injection pressures climb past 30,000 PSI in modern engines, fuel cleanliness has never been more critical. A single tank of contaminated fuel can cause thousands in injector damage. This filter provides the first and most important line of defense for your fuel system. Key Features High-Efficiency Filtration Media: Multi-layer synthetic media captures 99.9% of particles at the rated micron level, exceeding standard cellulose elements in both efficiency and dirt-holding capacity. Advanced Water Separation: Coalescing technology removes emulsified and free water from diesel fuel, preventing injector tip erosion and microbial growth. OEM-Spec Construction: Manufactured to ISO 9001 quality standards with precision-threaded base plate, anti-drain back valve, and high-burst-strength canister. Direct Fit Replacement: Engineered as a drop-in replacement — no modifications, adapters, or special tools required. Extended Service Life: Higher dirt-holding capacity means longer intervals between changes, reducing downtime and per-mile filtration costs. Compatibility Specification Detail Engine Cummins B6.7, ISL8.9, L9 Diesel Application Commercial Trucks, RVs, Buses Replaces Part # FS1098, 5319680, 5308722 Micron Rating 2-10 Micron Absolute Filter Type Spin-On with Water Separation Why Upgrade Your Fuel Filtration? Extended Injector Life: Injectors operating at 30,000+ PSI have micron-level clearances. Better filtration means injectors lasting 200K+ miles instead of failing at 100K. Improved Cold-Weather Reliability: Superior water separation prevents ice crystal formation in fuel lines during winter. Reduced Maintenance Costs: Preventing one HPFP failure saves $5,000-$10,000 — the cost of a lifetime of premium filters. Better Fuel Economy: Clean injectors atomize fuel more efficiently, maintaining optimal combustion over the vehicle lifetime. Installation Guide Safety First: Park on level ground, engage parking brake, allow engine to cool. Have a drain pan ready. Relieve Fuel Pressure: Remove fuel cap. On some models, pull fuel pump fuse and crank briefly. Remove Old Filter: Use oil filter wrench to loosen. Unscrew by hand and lower into drain pan. Prep New Filter: Apply thin film of clean diesel to gasket. Pre-fill if housing design allows. Install: Spin on by hand until gasket contacts. Tighten 3/4 to 1 full turn. DO NOT over-tighten with wrench. Prime System: Cycle key ON (not START) 5-6 times for 30 seconds each to purge air. Check for leaks. Start & Verify: Start engine, check for leaks at idle, let run 2 minutes, recheck. Dispose of old filter properly. Frequently Asked Questions Q: What engines does this fit?A: Fits Cummins B6.7, ISL8.9, and L9 diesel engines in Freightliner M2, International MV, Blue Bird Vision buses, motorhomes, and commercial vehicles from 2010-present. Replaces OEM part numbers 5319680 and 5308722. Q: How is this different from the fuel filter?A: FS1098 is a fuel water separator — it removes water, sediment, and larger particles BEFORE fuel enters the main filter. This 2-stage filtration protects the high-pressure common rail system. Replace both filters together. Q: What micron rating?A: 10-micron nominal filtration with 98% water separation efficiency. Integrated PCV (pressure control valve) maintains consistent fuel pressure. Exceeds OEM water removal performance. Q: How often should I drain the water separator?A: Drain the water bowl weekly during regular operation or when the WIF (Water-In-Fuel) warning light illuminates. For sitting vehicles, drain monthly. Water accumulation is higher in humid climates and with biodiesel blends above B5. Q: Can I use this on my RV Cummins generator?A: Yes. If your RV has a Cummins Onan generator with B6.7 or ISL engine platform, this is a direct fit. Verify generator model number — common on class A diesel pushers with Onan QD series. Related Products Shop All Fuel Filters & Water Separators → Diesel Engine Oil Filters → Air Filters — Complete Intake Protection → Related Guides & Articles Diesel Fuel System Maintenance: Complete Guide → How to Prevent Diesel Fuel Contamination → Common Rail Diesel Injector Failure: Warning Signs → 📖 Related Guide: Read our complete installation guide and comparison →

Read more less

Product Overview The Pressure Sensor for Onan A042P619 Generator Carburetor KY Series is a premium-quality replacement part engineered for durability and precise fitment. Whether you're a professional mechanic or a DIY enthusiast, this component delivers OEM-grade performance at an affordable price. Manufactured with high-grade materials to withstand demanding conditions, it ensures reliable operation and long service life. Designed as a direct-fit replacement, installation is straightforward with basic hand tools — no special modifications required. Each unit undergoes rigorous quality inspection before shipping to guarantee it meets or exceeds factory specifications. Key Features Premium Construction: Built with high-grade materials for maximum durability and corrosion resistance Direct Fit: Precision-engineered to match OEM specifications — no modifications needed Easy Installation: Designed for straightforward bolt-on replacement with standard tools Rigorously Tested: Each unit passes strict quality control checks before shipment Cost-Effective: OEM-quality performance without the dealership price tag Fast Shipping: Ships from our US warehouse with reliable delivery Compatibility Please verify fitment before ordering. This product is designed to be compatible with the following applications: Compatible Brands Onan Replaces Part # A042P619 G, KY S ⚠️ Important: Always cross-reference your vehicle's year, make, model, and existing part number before ordering. Contact our support team if you need assistance confirming compatibility. Product Specifications Part Number(s) A042P619 G, KY S Brand iFJF Condition New SKU FJ-FSS27 Price $37.99 Why Choose iFJF? At iFJF, we specialize in providing high-quality aftermarket parts and accessories for automotive, powersports, RV, and outdoor equipment. Our mission is simple: deliver reliable, affordable replacement parts that professionals and DIYers can count on. ✅ Rigorous quality testing on every batch ✅ Fast, reliable shipping from US warehouses ✅ Responsive customer support team ✅ Thousands of satisfied customers nationwide Installation Tips Safety First: Disconnect the battery (if applicable) and wear appropriate safety gear before starting. Prepare Tools: Gather all necessary tools before beginning — check product listing for any special tool requirements. Remove Old Part: Carefully remove the existing component, noting the orientation and connections. Compare Parts: Place old and new parts side-by-side to verify fitment before installation. Install New Part: Mount the new component in the same orientation, ensuring all connections are secure. Test: After installation, test operation thoroughly before returning to regular use. Note: If you're unsure about any step of the installation process, we recommend consulting a professional mechanic or technician. Frequently Asked Questions Q: Is this a genuine OEM part?A: This is a high-quality aftermarket replacement part manufactured to meet or exceed OEM specifications. It is NOT a genuine OEM part. Q: Will this fit my vehicle?A: Please verify compatibility using the specifications and compatibility table above. Match your vehicle's year, make, model, and existing part number before ordering. Q: What is included in the package?A: The package includes the Pressure Sensor for Onan A042P619 Generator Carburetor KY Se as shown in the product images. Please refer to the listing photos for exactly what's included. Q: How long does shipping take?A: We ship from our US warehouse. Standard shipping typically takes 3-7 business days within the continental US. Expedited options are available at checkout. Q: What is your return policy?A: We offer a 30-day return policy for unused items in original packaging. If you receive a defective product, contact us immediately for a replacement or refund. Q: Do you offer warranty?A: Yes, all iFJF products come with a satisfaction guarantee. If you experience any issues, reach out to our support team for assistance. Order With Confidence Join thousands of satisfied customers who trust iFJF for their parts and accessories needs. With our commitment to quality, fast shipping, and excellent customer service, you can shop with confidence. Click "Add to Cart" now to get your Pressure Sensor for Onan A042P619 Generator Carburetor KY Se delivered fast!

Read more less

Product Overview The iFJF R18189-30 Spin-On Fuel Filter is a heavy-duty 30-micron filter designed for mobile and stationary diesel applications. Featuring a standard 1-inch NPT port, this spin-on filter provides reliable primary fuel filtration for generator sets, fuel transfer systems, mobile refueling equipment, and stationary diesel engines. The 30-micron rating makes it ideal as a primary filter before finer secondary filtration. Robust construction for demanding industrial and mobile service. Key Features 30-Micron Primary Filtration: Optimal for first-stage filtration — catches larger particles and debris before they reach finer secondary filters downstream. 1-Inch NPT Port: Industry-standard thread for easy integration with fuel transfer pumps, generator fuel systems, and bulk filtration setups. Spin-On Convenience: Quick-change design — no housing to disassemble, just spin off the old filter and spin on the new one. Mobile & Stationary Compatible: Suitable for fuel transfer trailers, generator sets, agricultural equipment, construction machinery, and stationary diesel engines. Heavy-Duty Construction: Reinforced canister designed for high flow rates and continuous duty in industrial applications. Applications Application Type Examples Mobile Fuel Transfer Fuel transfer trailers, tanker trucks, mobile refueling skids Stationary Engines Generator sets, irrigation pumps, industrial diesels Bulk Filtration Fuel storage tank filtration, fuel polishing systems Agricultural Equipment Tractors, combines, harvesters with NPT fuel lines Construction Equipment Excavators, dozers, loaders with auxiliary fuel systems Specifications Specification Detail Part Number R18189-30 Micron Rating 30 Micron (Nominal) Port Size 1 Inch NPT (Female) Filter Type Spin-On (Canister) Media Cellulose/Synthetic Blend Fuel Compatibility Diesel, Biodiesel (up to B20) Frequently Asked Questions Q: Is 30 micron enough for diesel engines?A: 30 micron is ideal for primary (first-stage) filtration. It should be paired with a finer secondary filter (10 micron or less) before the injection pump for complete protection. Q: What's the 1-inch NPT connection for?A: The 1-inch NPT port fits standard fuel transfer pump plumbing, generator fuel systems, and industrial diesel setups with NPT-threaded fuel lines. Q: Can I use this for gasoline?A: This filter is designed for diesel fuel applications. Verify compatibility before using with gasoline or other fuels. Q: How often should this filter be replaced?A: Monitor the pressure gauge across the filter head. Replace when pressure drop exceeds 8-10 PSI, or every 500 hours of operation — whichever comes first. Q: Does this filter separate water?A: The primary function is particulate filtration at 30 microns. For water separation, pair with a dedicated water separator or use a filter with coalescing media downstream.

Read more less

Product OverviewCNC-machined billet aluminum EGR delete block-off plate kit for 1983-1997 Ford F-150, F-250, F-350, and Bronco with 4.9L 300 I6, 5.0L 302, 5.8L 351W, and 7.5L 460 engines. This kit eliminates the problematic EGR system that causes carbon buildup, rough idle, and reduced performance. Precision-cut for perfect sealing with included gaskets and hardware. For off-road and competition use only. Key Features Billet Aluminum: CNC-machined from 6061-T6 billet aluminum for superior strength and corrosion resistance — far more durable than stamped steel alternatives. Complete Kit: Includes block-off plate, high-temperature gasket, and Grade 8 mounting hardware — everything needed for a leak-free installation. Eliminates Carbon Buildup: By removing the EGR system, you prevent exhaust gas recirculation that causes intake manifold carbon deposits, rough idle, and throttle body contamination. Precision Fit: CAD-designed to exact OEM EGR valve mounting dimensions — no modification, drilling, or grinding required. Cleaner Engine Bay: Removes cluttered EGR vacuum lines, solenoid, and valve for a simplified, professional-looking engine compartment. Compatibility Make Model Engine Year Ford F-150, F-250, F-350, Bronco 4.9L 300 I6, 5.0L 302, 5.8L 351W, 7.5L 460 1983-1997 Specifications Specification Detail Material 6061-T6 Billet Aluminum Finish Natural Machined Includes Block-Off Plate + Gasket + Hardware Application EGR Valve Block-Off Usage Off-Road / Competition Only Why Choose iFJFAt iFJF Direct, we engineer performance solutions for enthusiasts who demand quality. Every product is CNC-machined to exact specifications and backed by our 1-year warranty. We ship from our US warehouse with fast, tracked delivery. ⚠️ Disclaimer: This product is intended for off-road and competition use only. It is not CARB-compliant and may not be legal for on-highway use in your jurisdiction. Frequently Asked QuestionsQ: Is this EGR delete kit street legal?A: No. EGR deletes are intended for off-road, racing, and competition use only. Removing emissions equipment may violate federal and state laws. Check local regulations before installation. Q: Will this trigger a check engine light?A: Yes, removing the EGR system will trigger a check engine light on OBD-I and OBD-II vehicles. An EGR simulator or custom ECU tune is recommended. Q: Do I need special tools?A: Basic hand tools — ratchet, socket set, gasket scraper. Installation takes approximately 30-60 minutes depending on engine bay access. Q: What is your return policy?A: We offer a 30-day return policy for unused items in original packaging. Contact us for a replacement or full refund if you receive a defective product. Q: How fast is shipping?A: Orders ship within 1-2 business days from our US warehouse. Standard shipping takes 3-7 business days. Expedited options available at checkout. Q: Do you offer warranty?A: Yes, all iFJF products come with a 1-year warranty against manufacturing defects. Order with ConfidenceReady to simplify your engine bay? Add to cart now and enjoy free shipping on orders $50+. Questions? Contact our support team — we respond within 24 hours.

Read more less

68229402AA Engine Oil Filter — Ram 1500 and Jeep Grand Cherokee 3.0L EcoDiesel Turbocharged diesel engines run hot and are tough on oil. The iFJF 68229402AA Engine Oil Filter provides factory-spec filtration for the 3.0L V6 EcoDiesel (EXF engine) found in 2014-2019 Ram 1500 and 2014-2020 Jeep Grand Cherokee. This high-efficiency cartridge filter replaces Mopar part numbers 68229402AA and 68109834AA. Also cross-references to WIX WF10245. Key Features Synthetic-Blend Media: Advanced filtration provides consistent oil flow across full service interval while trapping particles to 25 microns High-Temperature Rated: Engineered for elevated oil temperatures of turbocharged diesels—no media breakdown, no bypass Anti-Drainback Protection: Integrated silicone anti-drainback valve prevents dry starts by keeping oil in the filter OEM-Exact Fit: Precision-molded cartridge ensures perfect seal in oil filter housing—no bypass, no leaks Complete Kit: Includes new O-ring seals for filter cap and housing—replace both with every oil change Compatibility Vehicle Engine Years Ram 1500 3.0L V6 EcoDiesel (EXF) 2014-2019 Jeep Grand Cherokee 3.0L V6 EcoDiesel (EXF) 2014-2020 Specifications Specification Detail Part Number 68229402AA / FJ-02AA Replaces 68229402AA, 68109834AA, WF10245 Filter Type Cartridge (Housing-Style) Filtration 25 Micron Nominal Oil Spec 5W-40 Full Synthetic Diesel (10.5 qt) Frequently Asked Questions Q: Will this fit my 2016 Ram EcoDiesel?A: Yes. Correct oil filter for all 2014-2019 Ram 1500 with 3.0L V6 EcoDiesel. Q: Includes O-rings?A: Yes. Kit includes filter cap O-ring and housing seals for complete installation. Q: Same as Mopar dealer filter?A: Premium aftermarket equivalent meeting or exceeding Mopar specs at lower price. Q: What oil should I use?A: 5W-40 full synthetic diesel oil meeting Chrysler MS-10902 or ACEA C3. Popular: Rotella T6, Mobil 1 ESP. Q: Can I use on 2020+ EcoDiesel Gen 3?A: No. 2020+ Ram uses Gen 3 EcoDiesel with different filter. This is for Gen 2 (2014-2019). Related EcoDiesel Products 68235275AA Fuel Filter + Wrench Kit 68235275AA + 68229402AA Fuel and Oil Combo Helpful Articles iFJF Blog — EcoDiesel Maintenance Tips

Read more less

Product Overview High-quality aftermarket 0-4412S Carburetor Replacement — precision-engineered for reliable fuel/air metering and direct bolt-on fitment. Manufactured to meet or exceed OEM specifications at a fraction of dealer pricing. Key Features Precision Manufacturing: CNC-machined components ensure exact tolerances and smooth throttle response OEM-Spec Materials: Constructed from durable die-cast aluminum and corrosion-resistant components that withstand high temperatures and fuel exposure Direct Fitment: Designed as a direct bolt-on replacement — no modifications or adapters required for installation Flow-Tested: Each unit undergoes quality control testing to verify proper fuel and air metering calibration Complete Assembly: Comes fully assembled and pre-adjusted for out-of-the-box installation — saves hours of setup time Compatibility Information This carburetor & fuel system is designed to replace the factory original equipment on compatible vehicles. Please verify your vehicle's year, make, model, and engine specifications before ordering. Contact our support team if you need assistance confirming fitment for your specific application. Technical Specifications Specification Details Product Type Carburetor & Fuel System Condition New Aftermarket Installation Direct Bolt-On Replacement Warranty 1-Year Replacement Warranty Shipping Same-Day on Orders Before 2 PM EST Why Choose iFJF Direct? At iFJF Direct, we specialize in high-quality aftermarket automotive parts for gasoline and diesel engines. Every product is sourced from trusted manufacturers and backed by our satisfaction guarantee. We stock inventory in our US warehouse and ship same-day on orders placed before 2 PM EST. Installation Tips Always disconnect the battery before starting any fuel system work Use new gaskets and seals — reusing old gaskets is the #1 cause of vacuum leaks and poor idle Double-check all linkage connections and throttle operation before starting the engine Perform a final fuel leak check after installation with the engine running at idle and under throttle Allow a short break-in period for gaskets to fully seat before final tuning adjustments Frequently Asked Questions Q: Will this fit my vehicle?A: Please verify your specific year, make, model, and engine against the compatibility information listed in the product title. If unsure, contact our support team with your VIN. Q: Is this a genuine OEM part?A: This is a high-quality aftermarket replacement manufactured to OEM specifications. It offers equivalent or superior performance at significantly lower cost than OEM dealer parts. Q: Does this come pre-tuned?A: Yes, the unit comes pre-adjusted from the factory for typical applications. Minor idle mixture and speed adjustments may be needed for your specific engine setup and altitude. Q: What's included in the box?A: The complete assembly as shown in product images, mounting gasket(s), and basic installation instructions. Verify included components match your application before installation. Q: What is your return policy?A: 30-day return policy for unused items in original packaging. Defective products covered under 1-year warranty. See our Returns page for full details.

Read more less

Product Overview Upgrade your 2013-2018 Dodge Ram 6.7L Cummins with this professional-grade egr delete + cooler delete + throttle valve delete. Designed for the Ram 2500/3500, this kit delivers improved engine performance, reduced maintenance issues, and enhanced reliability. Whether you're a professional diesel mechanic or a DIY enthusiast, our precision-engineered components provide a bolt-on solution for your Dodge Ram truck. ⚠️ Off-Road Use Only: This product is intended for off-road and competition use only. Please check your local, state, and federal regulations before purchasing and installing emissions-related components. Key Features Precision Fit: Engineered specifically for 2013-2018 Dodge Ram 6.7L Cummins Ram 2500/3500 — direct bolt-on installation with no modifications required. Heavy-Duty Construction: Built with industrial-grade materials to withstand extreme temperatures and pressures in high-performance diesel applications. Complete Kit: Includes all necessary hardware — gaskets, bolts, block-off plates, and installation components for a straightforward install. Performance Gains: Eliminates common failure points in the OEM EGR/exhaust system, improving exhaust flow, reducing EGTs (Exhaust Gas Temperatures), and enhancing throttle response. Corrosion Resistant: All components feature corrosion-resistant finishes to withstand road salt, moisture, and extreme weather conditions. Compatibility Year Make Model Engine 2013 Dodge/Ram 2500/3500 6.7L Cummins Diesel 2014 Dodge/Ram 2500/3500 6.7L Cummins Diesel 2015 Dodge/Ram 2500/3500 6.7L Cummins Diesel 2016 Dodge/Ram 2500/3500 6.7L Cummins Diesel 2017 Dodge/Ram 2500/3500 6.7L Cummins Diesel 2018 Dodge/Ram 2500/3500 6.7L Cummins Diesel Why Choose iFJF Direct? Quality Assurance: Every component undergoes rigorous quality control inspection before shipping. Expert Support: Our diesel specialists know 6.7L Cummins trucks inside out — installation help is just a message away. Frequently Asked Questions Q: Is this kit compatible with my 2013 Dodge Ram Ram 2500/3500?A: Yes! This kit is designed as a direct bolt-on for 2013-2018 Dodge Ram 6.7L Cummins Ram 2500/3500. No modifications are required for installation on stock vehicles. Q: What tools do I need for installation?A: Basic hand tools including socket set (8mm-19mm), torque wrench, flathead and Phillips screwdrivers, and penetrating oil for rusted fasteners. Most experienced DIY mechanics can complete the installation in 2-4 hours. Q: Will this delete kit trigger a check engine light (CEL)?A: This is a hardware-only kit. For complete functionality, appropriate ECU tuning is recommended to prevent DTCs (Diagnostic Trouble Codes). Professional tuning services are available from third-party providers. Q: Are gaskets and hardware included?A: Yes — all necessary gaskets, bolts, block-off plates, and mounting hardware are included in the kit. We recommend having replacement exhaust manifold gaskets on hand if your vehicle has high mileage. Q: How does this compare to OEM parts?A: Our components are engineered to solve the known failure points in the OEM emissions system. By eliminating problematic EGR coolers, valves, and restrictive exhaust components, you'll experience improved reliability, better fuel economy, and reduced maintenance costs. Q: What material are the block-off plates made from?A: Block-off plates are CNC-machined from 6061-T6 billet aluminum (or 304 stainless steel where noted) — far superior to OEM cast components that are prone to cracking and leaking under heat cycling. Q: Do you offer a warranty?A: Yes! All iFJF Direct products come with a satisfaction guarantee. If you have any issues with fitment or quality, contact our support team for a replacement or refund. Related Products iFJF 2013-2014 6.7L Cummins Dodge Ram Cab & Chassis Throttle Valve Cooler Diesel iFJF 2013-2014 6.7L Dodge Ram Cummins 3500 4'' Exhaust Tube Pipe/Cab & Chassis T iFJF 2013-2018 6.7L Cummins Diesel EGR Delete Kit for Cab & Chassis Dodge Ram iFJF 2013-2018 6.7L Dodge Ram 2500 3500 Turbo Diesel Generic 4'' Exhaust Tube Pi Complete Kit Recommendation Full Kit with 4" Exhaust Pipe for 2013-2014 Want the exhaust pipe too? The complete delete kit (EGR + Cooler + Throttle Valve + 4" pipe) is available for 2013-2014 Ram 3500/4500/5500 Cab & Chassis. View Complete Kit for 2013-2014

Read more less