920915 Furnace Control Board for Nordyne G7 M7 — Replaces 624742

Description

920915 Furnace Control Board for Nordyne G7 M7 — Replaces 624742

The 920915 integrated furnace control board is a direct replacement control for Nordyne and Nortek single-stage gas furnaces in the G7 and M7 series, including Miller, Intertherm, Tappan, Frigidaire and Gibson models. It replaces 624742, 624690, 624844, 904840 and 277820, runs on 24 VAC control voltage with hot surface ignition, and sequences the inducer, gas valve and PSC blower while monitoring flame and safety limits through a single on-board LED diagnostic.

📋 Key Takeaways

  • ✅ Direct Replacement: Replaces 624742, 624690, 624844, 904840 and 277820 on Nordyne G7 and M7 single-stage gas furnaces.
  • ✅ Nortek Family Coverage: Fits G7 and M7 furnaces sold as Nordyne, Miller, Intertherm, Tappan, Frigidaire, Gibson and Broan.
  • ✅ Single-Stage 24 VAC Control: 24 VAC control voltage with a 24 VAC 60 Hz input — matched to the original 920915 application.
  • ✅ Hot Surface Ignition: Drives the HSI igniter and proves flame through the flame sensor, then opens the gas valve only when ignition is confirmed.
  • ✅ On-Board Diagnostics: An LED flash code reports pressure switch, limit and flame faults, so a no-heat call can be traced before parts are swapped.
  • ✅ Check Before You Order: Read the part number on your old board — this is not a universal control board for other furnace brands.

Features & Benefits

Feature Benefit (What It Means for You)
Integrated Furnace Control (IFC) One board handles the full single-stage heating sequence — inducer proof, hot surface igniter warm-up, gas valve timing, blower on/off delay and cool-down — so the furnace runs the way the original control ran it.
Replaces 624742 624690 624844 904840 277820 A furnace whose parts list shows any of these numbers uses this board, which removes the guesswork of matching an earlier revision to the current 920915 part number.
24 VAC Control, 24 VAC 60 Hz Input Standard residential furnace control voltage with the same terminal designations as the original board, so existing thermostat, gas valve and blower wiring transfers without modification.
Hot Surface Ignition with Flame Sensing The board proves flame through the flame sensor on every call for heat and closes the gas valve if proof is lost, which protects against unburned gas accumulating in the heat exchanger.
LED Flash-Code Diagnostics A single on-board LED reports the fault the board has latched — pressure switch stuck open, open limit, or flame loss — so the failed component is identified before anything is replaced.
Drop-In Mounting Footprint The board mounts on the original standoffs inside the furnace control compartment and keeps the original terminal layout, so no bracket or harness modification is needed.

Compatibility & Cross-Reference

Replaces / Interchange Part Numbers:

Interchange Part Number System / Note
920915 Board number of this replacement
624742 Nordyne G7 / M7 control (earlier number for this board)
624690 Nordyne single-stage control (same board family)
624844 Nordyne / Nortek G7 series control
904840 Nordyne / Intertherm earlier control
277820 Nordyne legacy control number

The 920915 number is the current listing for this control; the 624742, 624844 and 904840 numbers are the earlier revisions of the same single-stage board, and 277820 appears in older Nordyne cross-reference lists.

Common Applications:

  • Nordyne G7 series single-stage gas furnaces — G7SA, G7SK, G7SC and G7SL models, for example G7SA090-35C1, G7SA126-45D1 and G7SK108-35C1
  • Nordyne KG7 series furnaces — KG7SA, KG7SC, KG7SD, KG7SK, KG7SL and KG7SM models, for example KG7SA-072C-24B
  • Frigidaire FG7 series furnaces — FG7SA, FG7SC, FG7SD, FG7SK, FG7SL and FG7SM models, for example FG7SA045C-23A and FG7SA126C-45D
  • Nordyne M7 series furnaces — M7RL models, plus CMF95 / CMF95072 heating units
  • Miller, Intertherm, Tappan, Gibson, Broan and Westinghouse furnaces built on the Nordyne G7 / M7 platform

This is a Nordyne-platform control, not a universal board. Confirm the number on your old board or your furnace model plate before ordering; a board from a different manufacturer will not interchange even when the connector count looks similar.

Specifications

Part Number 920915
Control Type Integrated furnace control (IFC), single stage
Ignition Hot surface ignition (HSI) with flame sensing
Control Voltage 24 VAC
Input Power 24 VAC, 60 Hz
Loads Controlled Gas valve, inducer motor, PSC blower, limit and pressure switch inputs
Diagnostics On-board LED flash code
Replaces 624742, 624690, 624844, 904840, 277820
Compatible Series Nordyne G7 and M7 single-stage gas furnaces (also Miller, Intertherm, Tappan, Frigidaire, Gibson, Broan)
Net Weight 8.6 oz (244 g)
Package Contents 1 × 920915 integrated furnace control board
Warranty iFJF Quality Guarantee

Why Choose iFJF?

iFJF supplies furnace control boards factory-direct, so the replacement part arrives without dealer markup. What you can verify before you buy:

  • ✅ Open cross-reference: every covered number (624742, 624690, 624844, 904840, 277820) is listed above — match your old board first.
  • ✅ Specification transparency: 24 VAC control voltage, 24 VAC 60 Hz input, hot surface ignition and LED diagnostics are stated openly so they can be compared with your original control.
  • ✅ Same terminal layout: terminals follow the original 920915 board, so wires move over one connector at a time with no cutting.
  • ✅ Factory-direct value: supply straight from the manufacturer keeps the price fair compared with an OEM dealer counter.
Installation note: a control board swap should be performed by a qualified HVAC contractor or licensed electrician. Turn off the furnace power at the disconnect and shut off the gas supply before removing the old board, and confirm 0 V with a meter. If you are unsure whether this board matches your furnace, message us with the model number from the furnace rating plate before ordering.

Need help confirming fitment? Our support team answers fitment questions before you order — support@ifjf.com.

Looking for a different furnace control board? Compare our 1170063 furnace control board for ICP furnaces, our 50A55-843 furnace control board for White-Rodgers and Lennox furnaces, or our 1012-925C furnace control board for Rheem and Ruud furnaces.

📂 Browse More: All Electronics Products →

Frequently Asked Questions

Q: Will the 920915 control board fit my furnace?

A: The 920915 board is built for Nordyne and Nortek single-stage gas furnaces in the G7 and M7 series, sold under the Nordyne, Miller, Intertherm, Tappan, Frigidaire, Gibson and Broan brands. Before ordering, read the part number printed on the old board: if it is 624742, 624690, 624844, 904840 or 277820, this board is the direct replacement. The Cross-Reference table above lists every covered number.

Q: Which part numbers does the 920915 board replace?

A: The 920915 integrated furnace control replaces 624742, 624690, 624844, 904840 and 277820. On Nordyne G7 and M7 furnaces the 624742 number was later carried as 920915, so a furnace whose parts list shows either number uses this same board.

Q: What are the electrical specifications of the 920915 board?

A: The 920915 board runs on 24 VAC control voltage with a 24 VAC 60 Hz input, drives a single-stage gas valve, and uses hot surface ignition with a flame sensor for proof of flame. It also switches the inducer motor and the PSC blower, and reports faults through an on-board LED flash code.

Q: Is this a genuine Nordyne OEM board?

A: No. This is an iFJF third-party replacement built to the same 24 VAC single-stage control specification and the same terminal layout as the original 920915 board. It is not sold as a Nordyne or Nortek OEM part, and the price reflects factory-direct supply rather than dealer markup.

Q: How do I install the 920915 control board?

A: Turn the furnace power off at the disconnect and shut off the gas supply, then photograph every connector before removing the old board. Unplug one connector at a time and move it to the identically marked terminal on the new board, mount the board on the original standoffs, restore power, and watch one full heat cycle end to end. A qualified HVAC technician should do the work if you are not comfortable with gas appliances.

Q: How do I know my old control board is actually the problem?

A: Typical control board failures are no ignition, the blower or inducer running continuously, a burner that starts and stops without a pattern, or a board LED that shows a fault code or stays dark. Check the low-voltage fuse on the board, the rollout and limit switches, the condensate switch and the ground first, and read the flash code from the label on your own board — codes differ between manufacturers — because a blown fuse or an open limit switch produces the same no-heat symptom as a failed board.

Package Includes

  • 1 × 920915 integrated furnace control board

Common Problems with Nordyne Furnace Control Boards — Solved by iFJF

We read verified owner reviews of Nordyne-platform replacement boards. Here is what keeps coming up — and how this board addresses it:

❌ What Owners Complain About ✅ How This Board Addresses It
"It says compatible but my furnace did not work"
— the #1 cause of returns in this category
→ Board number listed before the price
624742, 624690, 624844, 904840 and 277820 are printed in the table above, so the old board can be matched before ordering. This is a Nordyne-platform control, not a universal board.
"The blower runs but there is no heat"
— usually a flame-sensing or limit fault, not always the board
→ Flash code before parts
The on-board LED latches the actual fault — pressure switch, open limit or flame loss — so the fuse, rollout switch and flame sensor are checked before the board is condemned.
"The connectors did not line up with my old board"
— common when an earlier revision is swapped blind
→ Same terminal designations
Terminals follow the original 920915 layout, so wiring moves connector by connector from the photographed old board — no cutting, no splicing.

🔎 We read the 1-star and 2-star reviews so you don't have to. This board is built around the real failure modes on Nordyne G7 and M7 furnaces — not just a spec sheet.

Factory Direct Supply & Wholesale — iFJF is a direct manufacturer of high-performance replacement parts for heating and filtration systems. Custom specifications and bulk orders are highly welcome. Contact us for exclusive dealer pricing and volume discounts. Backed by ISO 9001:2015 and IATF 16949:2016 quality management system certifications.
Email: support@ifjf.com

920915 Furnace Control Board for Nordyne G7 M7 — Replaces 624742

Product form

SKU: FJ-CB-920915

$79.99

      Description

      920915 Furnace Control Board for Nordyne G7 M7 — Replaces 624742

      The 920915 integrated furnace control board is a direct replacement control for Nordyne and Nortek single-stage gas furnaces in the G7 and M7 series, including Miller, Intertherm, Tappan, Frigidaire and Gibson models. It replaces 624742, 624690, 624844, 904840 and 277820, runs on 24 VAC control voltage with hot surface ignition, and sequences the inducer, gas valve and PSC blower while monitoring flame and safety limits through a single on-board LED diagnostic.

      📋 Key Takeaways

      • ✅ Direct Replacement: Replaces 624742, 624690, 624844, 904840 and 277820 on Nordyne G7 and M7 single-stage gas furnaces.
      • ✅ Nortek Family Coverage: Fits G7 and M7 furnaces sold as Nordyne, Miller, Intertherm, Tappan, Frigidaire, Gibson and Broan.
      • ✅ Single-Stage 24 VAC Control: 24 VAC control voltage with a 24 VAC 60 Hz input — matched to the original 920915 application.
      • ✅ Hot Surface Ignition: Drives the HSI igniter and proves flame through the flame sensor, then opens the gas valve only when ignition is confirmed.
      • ✅ On-Board Diagnostics: An LED flash code reports pressure switch, limit and flame faults, so a no-heat call can be traced before parts are swapped.
      • ✅ Check Before You Order: Read the part number on your old board — this is not a universal control board for other furnace brands.

      Features & Benefits

      Feature Benefit (What It Means for You)
      Integrated Furnace Control (IFC) One board handles the full single-stage heating sequence — inducer proof, hot surface igniter warm-up, gas valve timing, blower on/off delay and cool-down — so the furnace runs the way the original control ran it.
      Replaces 624742 624690 624844 904840 277820 A furnace whose parts list shows any of these numbers uses this board, which removes the guesswork of matching an earlier revision to the current 920915 part number.
      24 VAC Control, 24 VAC 60 Hz Input Standard residential furnace control voltage with the same terminal designations as the original board, so existing thermostat, gas valve and blower wiring transfers without modification.
      Hot Surface Ignition with Flame Sensing The board proves flame through the flame sensor on every call for heat and closes the gas valve if proof is lost, which protects against unburned gas accumulating in the heat exchanger.
      LED Flash-Code Diagnostics A single on-board LED reports the fault the board has latched — pressure switch stuck open, open limit, or flame loss — so the failed component is identified before anything is replaced.
      Drop-In Mounting Footprint The board mounts on the original standoffs inside the furnace control compartment and keeps the original terminal layout, so no bracket or harness modification is needed.

      Compatibility & Cross-Reference

      Replaces / Interchange Part Numbers:

      Interchange Part Number System / Note
      920915 Board number of this replacement
      624742 Nordyne G7 / M7 control (earlier number for this board)
      624690 Nordyne single-stage control (same board family)
      624844 Nordyne / Nortek G7 series control
      904840 Nordyne / Intertherm earlier control
      277820 Nordyne legacy control number

      The 920915 number is the current listing for this control; the 624742, 624844 and 904840 numbers are the earlier revisions of the same single-stage board, and 277820 appears in older Nordyne cross-reference lists.

      Common Applications:

      • Nordyne G7 series single-stage gas furnaces — G7SA, G7SK, G7SC and G7SL models, for example G7SA090-35C1, G7SA126-45D1 and G7SK108-35C1
      • Nordyne KG7 series furnaces — KG7SA, KG7SC, KG7SD, KG7SK, KG7SL and KG7SM models, for example KG7SA-072C-24B
      • Frigidaire FG7 series furnaces — FG7SA, FG7SC, FG7SD, FG7SK, FG7SL and FG7SM models, for example FG7SA045C-23A and FG7SA126C-45D
      • Nordyne M7 series furnaces — M7RL models, plus CMF95 / CMF95072 heating units
      • Miller, Intertherm, Tappan, Gibson, Broan and Westinghouse furnaces built on the Nordyne G7 / M7 platform

      This is a Nordyne-platform control, not a universal board. Confirm the number on your old board or your furnace model plate before ordering; a board from a different manufacturer will not interchange even when the connector count looks similar.

      Specifications

      Part Number 920915
      Control Type Integrated furnace control (IFC), single stage
      Ignition Hot surface ignition (HSI) with flame sensing
      Control Voltage 24 VAC
      Input Power 24 VAC, 60 Hz
      Loads Controlled Gas valve, inducer motor, PSC blower, limit and pressure switch inputs
      Diagnostics On-board LED flash code
      Replaces 624742, 624690, 624844, 904840, 277820
      Compatible Series Nordyne G7 and M7 single-stage gas furnaces (also Miller, Intertherm, Tappan, Frigidaire, Gibson, Broan)
      Net Weight 8.6 oz (244 g)
      Package Contents 1 × 920915 integrated furnace control board
      Warranty iFJF Quality Guarantee

      Why Choose iFJF?

      iFJF supplies furnace control boards factory-direct, so the replacement part arrives without dealer markup. What you can verify before you buy:

      • ✅ Open cross-reference: every covered number (624742, 624690, 624844, 904840, 277820) is listed above — match your old board first.
      • ✅ Specification transparency: 24 VAC control voltage, 24 VAC 60 Hz input, hot surface ignition and LED diagnostics are stated openly so they can be compared with your original control.
      • ✅ Same terminal layout: terminals follow the original 920915 board, so wires move over one connector at a time with no cutting.
      • ✅ Factory-direct value: supply straight from the manufacturer keeps the price fair compared with an OEM dealer counter.
      Installation note: a control board swap should be performed by a qualified HVAC contractor or licensed electrician. Turn off the furnace power at the disconnect and shut off the gas supply before removing the old board, and confirm 0 V with a meter. If you are unsure whether this board matches your furnace, message us with the model number from the furnace rating plate before ordering.

      Need help confirming fitment? Our support team answers fitment questions before you order — support@ifjf.com.

      Looking for a different furnace control board? Compare our 1170063 furnace control board for ICP furnaces, our 50A55-843 furnace control board for White-Rodgers and Lennox furnaces, or our 1012-925C furnace control board for Rheem and Ruud furnaces.

      📂 Browse More: All Electronics Products →

      Frequently Asked Questions

      Q: Will the 920915 control board fit my furnace?

      A: The 920915 board is built for Nordyne and Nortek single-stage gas furnaces in the G7 and M7 series, sold under the Nordyne, Miller, Intertherm, Tappan, Frigidaire, Gibson and Broan brands. Before ordering, read the part number printed on the old board: if it is 624742, 624690, 624844, 904840 or 277820, this board is the direct replacement. The Cross-Reference table above lists every covered number.

      Q: Which part numbers does the 920915 board replace?

      A: The 920915 integrated furnace control replaces 624742, 624690, 624844, 904840 and 277820. On Nordyne G7 and M7 furnaces the 624742 number was later carried as 920915, so a furnace whose parts list shows either number uses this same board.

      Q: What are the electrical specifications of the 920915 board?

      A: The 920915 board runs on 24 VAC control voltage with a 24 VAC 60 Hz input, drives a single-stage gas valve, and uses hot surface ignition with a flame sensor for proof of flame. It also switches the inducer motor and the PSC blower, and reports faults through an on-board LED flash code.

      Q: Is this a genuine Nordyne OEM board?

      A: No. This is an iFJF third-party replacement built to the same 24 VAC single-stage control specification and the same terminal layout as the original 920915 board. It is not sold as a Nordyne or Nortek OEM part, and the price reflects factory-direct supply rather than dealer markup.

      Q: How do I install the 920915 control board?

      A: Turn the furnace power off at the disconnect and shut off the gas supply, then photograph every connector before removing the old board. Unplug one connector at a time and move it to the identically marked terminal on the new board, mount the board on the original standoffs, restore power, and watch one full heat cycle end to end. A qualified HVAC technician should do the work if you are not comfortable with gas appliances.

      Q: How do I know my old control board is actually the problem?

      A: Typical control board failures are no ignition, the blower or inducer running continuously, a burner that starts and stops without a pattern, or a board LED that shows a fault code or stays dark. Check the low-voltage fuse on the board, the rollout and limit switches, the condensate switch and the ground first, and read the flash code from the label on your own board — codes differ between manufacturers — because a blown fuse or an open limit switch produces the same no-heat symptom as a failed board.

      Package Includes

      • 1 × 920915 integrated furnace control board

      Common Problems with Nordyne Furnace Control Boards — Solved by iFJF

      We read verified owner reviews of Nordyne-platform replacement boards. Here is what keeps coming up — and how this board addresses it:

      ❌ What Owners Complain About ✅ How This Board Addresses It
      "It says compatible but my furnace did not work"
      — the #1 cause of returns in this category
      → Board number listed before the price
      624742, 624690, 624844, 904840 and 277820 are printed in the table above, so the old board can be matched before ordering. This is a Nordyne-platform control, not a universal board.
      "The blower runs but there is no heat"
      — usually a flame-sensing or limit fault, not always the board
      → Flash code before parts
      The on-board LED latches the actual fault — pressure switch, open limit or flame loss — so the fuse, rollout switch and flame sensor are checked before the board is condemned.
      "The connectors did not line up with my old board"
      — common when an earlier revision is swapped blind
      → Same terminal designations
      Terminals follow the original 920915 layout, so wiring moves connector by connector from the photographed old board — no cutting, no splicing.

      🔎 We read the 1-star and 2-star reviews so you don't have to. This board is built around the real failure modes on Nordyne G7 and M7 furnaces — not just a spec sheet.

      Factory Direct Supply & Wholesale — iFJF is a direct manufacturer of high-performance replacement parts for heating and filtration systems. Custom specifications and bulk orders are highly welcome. Contact us for exclusive dealer pricing and volume discounts. Backed by ISO 9001:2015 and IATF 16949:2016 quality management system certifications.
      Email: support@ifjf.com

      Recently viewed products

      © 2026 iFJF Direct | Sitemap

        • American Express
        • Diners Club
        • Discover
        • Maestro
        • Mastercard
        • PayPal
        • Visa

        Login

        Forgot your password?

        Don't have an account yet?
        Create account