Search results for "Briggs"

Product Overview The B085011 is a primary round air filter element designed for diesel engine compartments in heavy equipment, commercial trucks, and industrial applications. This cylindrical filter serves as the first stage of engine air filtration, capturing coarse to medium particulates before air reaches the secondary/safety filter. Built for high-dust environments, it provides the dirt-holding capacity and airflow volume that medium to large diesel engines demand. Key Features Wide Cross-Reference Compatibility: Replaces B085011, CA6818, 46637, AH1141, and PA2818 — covering multiple OEM and aftermarket part number systems Primary Stage Filtration: Designed as the outer/primary element in two-stage air filtration systems — pair with the appropriate safety/inner filter for complete protection High Dirt-Holding Capacity: Pleated cellulose media with deep dirt-loading channels extends service intervals in dusty operating conditions Universal Round Design: Fits numerous engine compartment air cleaner housings — verify dimensions before ordering to confirm fitment Heavy-Duty Construction: Reinforced metal end caps and center tube prevent collapse under high vacuum conditions Moisture Resistant: Treated media resists water absorption from rain, humidity, and engine compartment condensation Specifications Specification Value Part Number B085011 Cross References CA6818, 46637, AH1141, PA2818 Filter Type Primary Round Air Filter (Cylindrical) Media Type Heavy-Duty Pleated Cellulose End Cap Material Galvanized Steel Center Tube Perforated Steel Seal Type Radial Lip Seal (Integrated Gasket) Service Interval 500 hours or when restriction indicator shows red Application Diesel Engine Compartment Air Cleaner Housings Installation Guide Locate the cylindrical air cleaner housing in the engine compartment Release the housing cover — typically a wing nut, band clamp, or spring latches Remove the cover and slide out the old primary filter Inspect the safety/inner filter (if equipped) — do not remove unless replacing; the safety filter should only be replaced, never cleaned Wipe the housing interior clean with a damp cloth — avoid introducing dust into the clean-air side Check the housing seal and cover gasket for cracks or damage Install the new B085011 filter — ensure the radial seal seats evenly and the filter centers properly Replace the cover and secure all fasteners Reset the air filter restriction indicator (press the reset button) Start the engine and check for unusual intake noise or warning indicators Frequently Asked Questions Q: What equipment uses the B085011 filter?A: This filter is used across multiple diesel engine applications where a round primary filter of this specific size is spec'd. Applications include heavy trucks, construction equipment, agricultural machinery, generator sets, and industrial engine packages. Always cross-reference your existing filter number or measure your housing to confirm fitment. Q: Is this a primary or secondary filter?A: This is a PRIMARY (outer) filter. In two-stage air cleaner systems, the primary filter captures the majority of contaminants, while the safety/inner filter provides backup protection during primary filter service. This B085011 is the primary element. Q: Can I clean and reuse this filter?A: Not recommended. While some operators attempt to blow out round filters with compressed air, this practice often damages the media, creates invisible tears, and forces dirt deeper into the filter. For the cost of a replacement compared to the cost of engine damage, replacement is always the safer option. Q: How do I know what size filter I need?A: Measure your existing filter: outer diameter, inner diameter (the open center hole), and overall length/height. Compare these measurements against known filter specifications. Alternatively, cross-reference the part number on your existing filter. Q: What happens if the air filter gets wet?A: A wet air filter restricts airflow dramatically and can cause the engine to run rich, smoke, and lose power. In severe cases, water-saturated media can collapse, allowing unfiltered air into the engine. If your filter gets wet (e.g., from pressure washing the engine bay), replace it immediately. Related Products AF55020 Air Filter for Cummins QSF/QSB Engines — Similar cylindrical industrial filter AF55015 Air Filter for Cummins QSB6.7/QSC/QSL9 — Larger round filter option A3231C Air Filter for Duramax L5P — Heavy-duty diesel truck filter Blog Resources For air filtration selection guides, heavy equipment maintenance schedules, and diesel engine care tips, visit our Diesel Engine Maintenance Blog.

Read more less

John Deere Engine Oil Filter — Premium Protection The RE504836 Engine Oil Filter Replacement for John Deere 5076E 5082E 5083 provides superior engine protection for John Deere tractors. High-efficiency filtration media removes microscopic particles that cause engine wear. Meets or exceeds OEM specifications RE504836, RE507522, RE541420, and RE502513 for reliable performance in demanding agricultural applications. Key Features OEM-Spec Filtration: Meets John Deere RE504836, RE507522, RE541420, RE502513 specifications High-Capacity Media: Extended filter surface area for longer service intervals Anti-Drain Back Valve: Prevents dry starts by keeping oil in the filter between uses Heavy-Duty Canister: Reinforced steel housing withstands agricultural operating conditions Easy Spin-On Install: Standard thread pattern for quick filter changes in the field Compatibility John Deere Fitment: 5076E, 5082E, 5083E, 5085M, 5090E, 5090M, 5100E, 5100M tractorsCross References: RE504836, RE507522, RE541420, RE502513, John Deere OEM part numbers Technical Specifications Filter Type Spin-On Full Flow Oil Filter Filtration Rating 25 Micron (Nominal) Anti-Drain Back Valve Yes — Silicone Bypass Valve Yes — 12-15 PSI Thread Size Standard John Deere Spin-On Pattern Service Interval Every 200 Hours or Per Manufacturer Spec Why Choose iFJF Direct Fast US Shipping: Orders ship from our US warehouse within 1 business day Quality Guaranteed: Every product inspected before shipping Expert Support: Diesel and pool specialists ready to help with fitment questions Trusted by Mechanics: 5,000+ positive reviews from professional technicians and DIYers Frequently Asked Questions Q: Will this fit my John Deere 5076E?A: Yes, this filter is compatible with John Deere 5076E, 5082E, 5083E, 5085M, 5090E, and 5100E tractors. It replaces OEM part numbers RE504836, RE507522, RE541420, and RE502513. Q: How often should I change the oil filter?A: John Deere recommends every 200 hours for most utility tractor applications. Always change the filter with every oil change — never reuse an old filter. Q: Does this have an anti-drain back valve?A: Yes, this filter features a silicone anti-drain back valve that prevents oil from draining out of the filter when the engine is off, ensuring immediate oil pressure on cold starts. Q: Can I use this on older John Deere models?A: If your tractor uses the RE504836, RE507522, or RE502513 series filters, this is a direct replacement. Always verify your specific model's filter requirements in the operator's manual. Related Products FS1242 Fuel Water Separator TP1015 Fuel Filter Duramax Fuel Filter Assembly Ram 6.7L

Read more less

Overview The iFJF 7834 Rear Crankshaft Seal Installer is a precision-engineered automotive tool for professional-grade installation of rear main oil seals on Ford 4.0L V6 engines. Compatible with 1993-1997 Aerostar, 1993-2006 Ranger, and Explorer, this set ensures flush, damage-free seal installation every time — with or without metal wear sleeves. Key Features Precision-Machined: CNC-machined components ensure perfect alignment during seal installation, preventing cocking or uneven seating that causes leaks. Dual Seal Compatibility: Works with crankshaft rear oil seals that come with or without a metal wear sleeve — maximum versatility for different seal types. Complete Installation Kit: Includes 1x seal installer, 1x seal protector, 1x seal adapter, and 3x mounting bolts — everything needed for a professional job. Durable Construction: Made from high-grade steel with a corrosion-resistant finish for long tool life in demanding workshop environments. Vehicle-Specific Engineering: Designed specifically for the Ford 4.0L V6 engine platform, ensuring precise fitment on Aerostar, Ranger, and Explorer applications. DIY-Friendly Design: Clear sizing markings and intuitive assembly make this tool accessible for both professional mechanics and experienced DIYers. Compatibility Make Model Year Range Ford Aerostar 1993-1997 Ford Ranger 1993-2006 Ford Explorer 1993-2006 Specifications Specification Value Part Number 7834 Engine Compatibility 4.0L V6 (OHV & SOHC) Material High-Grade Steel Kit Components Installer + Protector + Adapter + 3 Bolts Seal Type Support With or Without Metal Wear Sleeve SKU FJ-TOOL139 Why Choose iFJF? At iFJF Direct, we specialize in high-quality replacement parts and tools backed by rigorous quality control. Each component is manufactured to meet or exceed OEM specifications, ensuring reliable performance and long service life. Improper seal installation is the #1 cause of rear main seal leaks — our precision tool eliminates this risk. We stand behind every product with responsive customer support and a satisfaction guarantee. Frequently Asked Questions Q: Will this work on seals with a metal wear sleeve?A: Yes. This installer is engineered to accommodate crankshaft rear oil seals both with and without metal wear sleeves. The included adapter handles both configurations seamlessly. Q: Does this fit both the OHV and SOHC 4.0L V6?A: Yes. This tool is compatible with both the OHV (pushrod) and SOHC versions of the Ford 4.0L V6 engine found in 1993-2006 Ranger, Explorer, and 1993-1997 Aerostar models. Q: Do I need any special tools beyond this kit?A: No special tools are required beyond basic hand tools (ratchet, sockets). The installer kit includes all necessary adapters, protector, and bolts for the complete job. Q: Is this tool reusable across multiple vehicles?A: Absolutely. The high-grade steel construction ensures this tool can be used for multiple seal replacements across different vehicles sharing the Ford 4.0L V6 engine platform. Q: Can improper installation cause rear main seal leaks?A: Yes — improper installation is the #1 cause of rear main seal leaks. A seal that's driven in crooked or at the wrong depth will leak almost immediately. This installer ensures the seal goes in flush and square every time. Q: What's included in the package?A: The kit includes: 1x Seal Installer, 1x Seal Protector, 1x Seal Adapter, and 3x Mounting Bolts. All packed in a protective case. Package Includes 1 x 7834 Rear Crankshaft Seal Installer for Ford 4.0L V6 | Installation hardware as shown | Product support documentation

Read more less

Overview The C4312/1 Engine Air Filter is engineered for Mercedes-Benz Sprinter vans — the backbone of commercial fleets across North America. Whether your Sprinter runs the 3.0L V6 Turbo Diesel (OM642) from 2007-2009 or the 2.1L I4 Twin-Turbo (OM651) from 2014 onward, this filter delivers the precise airflow and filtration your engine demands. Clean air = clean combustion = longer DPF life and better MPG. Key Features Dual-Generation Fit: Compatible with both OM642 V6 (2007-2009) and OM651 I4 (2014-2022) Sprinters OEM Replacement: Direct cross-reference for 68013676AA, CA10330, C4312/1 High-Dust Capacity: Deep pleat design handles commercial-duty dust loads without restricting flow Fuel Economy: Clean air filter improves diesel combustion efficiency by 2-5% Fleet-Grade Durability: Built for high-mileage, stop-and-go delivery cycles Compatibility Table Brand Model Engine Year Range Mercedes-Benz Sprinter 2500 3.0L V6 Turbo Diesel (OM642) 2007-2009 Mercedes-Benz Sprinter 3500 3.0L V6 Turbo Diesel (OM642) 2007-2009 Mercedes-Benz Sprinter 1500 2.1L I4 Twin-Turbo (OM651) 2014-2022 Mercedes-Benz Sprinter 2500 2.1L I4 Twin-Turbo (OM651) 2014-2022 Mercedes-Benz Sprinter 3500 2.1L I4 Twin-Turbo (OM651) 2014-2022 Freightliner Sprinter 2500/3500 3.0L V6 (2007-2009) / 2.1L I4 (2014+) 2007-2022 Specifications Spec Value Part Number (OEM) C4312/1, 68013676AA, CA10330 Filter Type Panel (Engine Air) Media Type High-capacity cellulose/synthetic Replacement Interval Every 20,000-30,000 miles or annually Why iFJF for Your Sprinter Fleet? Every filter tested to SAE J726 filtration standards Save 50-70% vs Mercedes dealership pricing Bulk fleet pricing available — contact us for volume discounts US-based support team with Sprinter technical knowledge FAQ Q: Will this fit my 2016 Sprinter 2500 2.1L?A: Yes. The C4312/1 fits all 2014-2022 Sprinter 1500/2500/3500 with the 2.1L OM651 4-cylinder diesel engine. Q: How often should I replace the air filter on a delivery Sprinter?A: For stop-and-go delivery routes in urban environments, replace every 15,000-20,000 miles. For highway use, 25,000-30,000 miles is standard. Inspect at every oil change. Q: What happens if I don't replace the air filter on time?A: A clogged filter restricts airflow, causing rich fuel mixture, increased DPF regen cycles, reduced MPG, and potential turbocharger damage from dirt ingestion. On a Sprinter, this can cost thousands in repairs. Q: Does this also fit Dodge Sprinter models?A: Yes — Dodge-badged Sprinters from 2007-2009 with the 3.0L V6 diesel are mechanically identical to Mercedes/Freightliner versions and use the same air filter.

Read more less

Overview The iFJF 8183061 Tire Machine Mount Head 5-Pack is a set of nylon plastic replacement duck heads for Coats tire changers. Compatible with Coats models 5030 through 7665 (all baseline series), this mount head replaces OEM part numbers 8183061, 183061, 8182960, 182960, 8183060, 183060, 8182788, and 182788. The nylon construction protects alloy and custom wheels from scratching during tire mounting and demounting — a critical consideration for high-end wheel service. Key Features Wheel-Safe Nylon Material: High-density nylon is tough enough for daily shop use but softer than wheel materials (aluminum, chrome, clear coat), preventing scratches on expensive wheels. 5-Pack Shop Value: Five mount heads provide months of continuous shop use at a fraction of single OEM replacement cost. Keep spares on hand to eliminate downtime. Broad Coats Compatibility: Fits virtually all Coats baseline tire changer models — 5000, 6000, and 7000 series — covering the most common machines in North American tire shops. Precision CNC-Molded: CNC-machined mold ensures exact dimensional tolerance for smooth bead handling without binding or excessive wear on the mount/demount head. Quick-Change Design: Standard quick-release mounting allows tool-free replacement in under 30 seconds, minimizing machine downtime during busy shop hours. Professional-Grade Durability: Engineered for high-volume tire shops processing 50+ tires daily. Nylon formulation resists chipping and cracking under heavy use. Compatibility Make Model Year/Type Coats 5030/5040/5050 BaseLine Coats 5060/5065 BaseLine Coats 6050/6060/6065 BaseLine Coats 7050/7055/7060/7065 BaseLine Coats 7660/7665 BaseLine Specifications Specification Value Replaces OEM 8183061, 183061, 8182960, 182960, 8183060, 183060, 8182788, 182788 Material High-Density Nylon Pack Size 5 Pieces (Black) Application Tire Mount/Demount Duck Head SKU FJ-TOOL124-5 Why Choose iFJF? At iFJF Direct, we specialize in high-quality replacement parts backed by rigorous quality control. Each component is manufactured to meet or exceed OEM specifications, ensuring reliable performance and long service life. We stand behind every product with responsive customer support and a satisfaction guarantee. Frequently Asked Questions Q: Which Coats models does this fit?A: This mount head fits all baseline Coats models: 5030, 5040, 5050, 5060, 5065, 6050, 6060, 6065, 7050, 7055, 7060, 7065, 7660, and 7665. Compare your existing duck head to product images if unsure. Q: Will this scratch customer wheels?A: No. The nylon material is specifically chosen because it is softer than aluminum, chrome, and clear coat. It provides the rigidity needed for tire mounting while being gentle on wheel finishes. Q: How long does one head last?A: In a busy shop (30-50 tires/day), each nylon head lasts 2-4 weeks depending on tire types and operator technique. This 5-pack provides months of service with spares always ready. Q: How do I install the new mount head?A: Most Coats machines use a quick-release pin or bolt. Remove the old head, align the new one in the bracket, and secure with original hardware. Takes less than 30 seconds. Package Includes 1 x iFJF 8183061 TC183061 Tire Machine/Changer Mount Head Nylon Plastic Replacement for Coats 8182960 182960 8183060 183060 183060 (5 Pack Black) | Installation hardware as shown | Product support documentation

Read more less

Product Overview Eliminate the restrictive and failure-prone EGR system on your 2010-2014 Ram 2500/3500 6.7L Cummins with this EGR Throttle Valve & Cooler Delete Kit from iFJF. The factory EGR system recirculates hot, soot-laden exhaust gas back into your engine's intake — causing carbon buildup, oil contamination, reduced performance, and elevated EGTs. This complete hardware kit replaces the EGR components with precision-machined billet aluminum delete plates and pipes, restoring clean airflow and reliability to your Cummins engine. Why Delete the EGR on Your 6.7L Cummins? The 6.7L Cummins is one of the most durable diesel platforms ever built — but the emissions systems hold it back. The EGR cooler is a known failure point that can leak coolant into the intake, and the EGR valve introduces abrasive soot particles into the combustion chamber. For off-road and competition applications, removing these components dramatically improves engine health and performance. Key Features Complete EGR System Delete — Throttle valve delete plate + EGR cooler delete components in one kit CNC-Machined Billet 6061-T6 Aluminum — Precision-engineered for perfect fit and long-term durability Eliminates Carbon Buildup — No more exhaust soot fouling your intake manifold, valves, and engine oil Reduced EGTs — Cooler exhaust gas temperatures for safer, more reliable operation under load Improved Turbo Response — Clean, unrestricted intake airflow for faster turbo spool Prevents EGR Cooler Failure — Eliminate the risk of internal coolant leaks causing hydrolock or head gasket damage Includes All Hardware — Gaskets, O-rings, bolts, and mounting hardware included Compatibility Year Make Model Engine 2010 Ram (Dodge) 2500 / 3500 6.7L Cummins Turbo Diesel 2011 Ram (Dodge) 2500 / 3500 6.7L Cummins Turbo Diesel 2012 Ram (Dodge) 2500 / 3500 6.7L Cummins Turbo Diesel 2013 Ram 2500 / 3500 6.7L Cummins Turbo Diesel 2014 Ram 2500 / 3500 6.7L Cummins Turbo Diesel Technical Specifications Specification Detail Material CNC-Machined Billet 6061-T6 Aluminum Finish Corrosion-Resistant Coating Application Off-Road / Competition Use Only Installation Professional Installation Recommended Tuning Required Yes — Custom ECU Tune Required to Disable EGR DTCs ⚠️ Important Legal Notice OFF-ROAD / COMPETITION USE ONLY. This EGR delete kit is intended exclusively for off-road and closed-course competition vehicles. It is NOT street-legal and does NOT comply with EPA or CARB emissions regulations. The purchaser assumes all responsibility for compliance with applicable laws. Frequently Asked Questions Q: What does this EGR delete kit include?A: This kit includes the EGR throttle valve delete plate, EGR cooler delete components, all necessary gaskets, O-rings, bolts, and mounting hardware for a complete installation. Q: Will this trigger a check engine light?A: Yes. The ECU will detect the missing EGR components and set diagnostic trouble codes. Custom ECU tuning is required to disable EGR-related DTCs and prevent limp mode. This kit is hardware only. Q: Is this legal for street use?A: OFF-ROAD / COMPETITION USE ONLY. EGR delete modifications are not EPA or CARB compliant and are not legal for on-road vehicles. Q: What are the benefits of EGR delete on a 6.7L Cummins?A: On off-road/competition vehicles, deleting the EGR system eliminates carbon buildup in the intake manifold, reduces soot contamination in engine oil, lowers EGTs, improves turbo response, and removes the risk of EGR cooler failure. Q: Do I need to remove the DPF as well?A: The EGR and DPF systems work together. For optimal results on competition vehicles, removing both systems with proper ECU tuning is recommended. However, this kit addresses the EGR system specifically. Q: What material is used?A: All delete components are CNC-machined from billet 6061-T6 aluminum with a corrosion-resistant finish, engineered to withstand the high-temperature environment of the 6.7L Cummins engine bay. Q: Does this fit my 2010-2014 Ram 2500/3500?A: Yes. This kit is designed for all 2010, 2011, 2012, 2013, and 2014 Ram 2500 and 3500 trucks equipped with the 6.7L Cummins turbo diesel engine. Why Choose iFJF? iFJF is your trusted source for diesel performance aftermarket parts. All our products are precision-engineered using premium materials and backed by responsive US-based customer support. From Cummins to Powerstroke to Duramax, we deliver the parts that keep your diesel running at its best. You May Also Need EGR Throttle Valve & Cooler Delete Kit — 2010-2014 Ram 6.7L EGR Valve Delete Kit for 2007-2018 Ram 6.7L Cummins 3.5" High Flow Intake Manifold Elbow for 2007-2018 Ram 6.7L ⚠️ Off-Road / Competition Use Only: This product is intended for off-road or competition vehicles only. Not legal for highway use on emissions-controlled vehicles in the US and many other jurisdictions. Check local and federal regulations before purchasing. Removal of emissions equipment may void your vehicle warranty. 🔗 Cummins Diesel Resources & Maintenance 📖 Related Guides: Ram 6.7L Cummins Fuel Filter Replacement: Complete DIY Guide (2013–2018) Diesel Fuel Filter Maintenance — When to Replace (Duramax, Powerstroke & Cummins) 🔍 Shop All Cummins Parts → | EGR Delete Parts → | Fuel Filters →

Read more less

Product Overview Protect your fuel injection system with the Pre-Fuel Filter Assembly for Perkins 403D/404D/1103 Diesel Engines — 130306380 from iFJF. This premium fuel filter delivers superior contaminant removal, safeguarding your injectors, injection pump, and entire fuel system from harmful debris, water, and particulate matter. Engineered as a direct OEM replacement for OEM specification, this filter features high-efficiency filtration media that captures particles as small as 30 microns. Whether you're maintaining a daily driver, work truck, or fleet vehicle, this filter ensures clean fuel delivery at every RPM. Key Features 30 Micron Filtration: High-efficiency media captures contaminants before they reach your injection system Water Separation: Separates emulsified water from diesel fuel, protecting injectors from corrosion High Flow Rate: Maintains proper fuel flow under high-demand conditions — towing, hauling, highway driving Durable Construction: Heavy-duty canister resistant to pressure spikes and vibration Direct OEM Fit: Exact dimensions, thread pattern, and gasket seal match the factory filter Multi-Fuel Compatible: Works with ULSD, biodiesel blends up to B20, and gasoline Specifications Specification Detail Part Type Fuel Filter / Fuel Water Separator Filtration Rating 30 Micron Nominal Media Type High-Efficiency Cellulose/Synthetic Blend OEM Cross-Reference OEM specification Fuel Type Diesel / Gasoline / Biodiesel (up to B20) Service Interval Every 15,000-25,000 miles or 12 months Installation Guide Safety First: Park on level ground, engage parking brake, allow engine to cool Relieve Pressure: Open fuel cap to relieve tank pressure Remove Old Filter: Use filter wrench if needed — have catch pan ready for fuel spillage Clean Surface: Wipe filter housing clean of debris and old gasket material Lubricate Gasket: Apply thin film of clean diesel to new filter's gasket Install: Hand-tighten until gasket contacts, then 3/4 turn more Prime System: Turn ignition ON (without starting) for 30 seconds, repeat 2-3 times Check: Start engine and check for leaks Why Choose iFJF Filters? Quality Tested: Every filter undergoes burst pressure, efficiency, and flow rate testing US-Based Support: Ships from US warehouses with real tracking Best Value: OEM-equivalent quality at a fraction of dealer pricing 30-Day Guarantee: Not satisfied? Free replacement or full refund Frequently Asked Questions Q: How often should I replace this fuel filter?A: For diesel engines: replace every 15,000-25,000 miles or annually. For vehicles operating in dusty conditions or using biodiesel, change every 10,000-15,000 miles. Q: Is this a direct OEM replacement?A: Yes. Manufactured to meet or exceed OEM specifications for fit, filtration efficiency, and flow rate. Direct drop-in replacement. Q: What micron rating is this filter?A: This filter has a 30 micron filtration rating, providing excellent contaminant removal while maintaining proper fuel flow. Q: Can I use this with biodiesel?A: Yes, compatible with diesel up to B20 biodiesel blends. For B20+, more frequent changes recommended due to biodiesel's solvent properties. Q: What are signs of a clogged fuel filter?A: Hard starting, rough idle, hesitation under acceleration, decreased fuel economy, and check engine light. Replace immediately if you notice these. Q: What's included in the package?A: The package includes the fuel filter element(s) as described in the title and product images. Multi-packs provide bulk value for fleet maintenance. 🔗 Related Products Looking for more? Browse our related products or check out our Best Sellers.

Read more less

Mercury Mariner 6HP-45HP Fuel Filter Kit — Replaces 35-889527A07 The 35-889527A07 fuel filter kit is engineered for Mercury and Mariner outboard motors from 6HP to 45HP. Featuring a high-strength plastic housing with a fluororubber (FKM) seal, this complete kit delivers reliable leak-free filtration in demanding marine environments — keeping your outboard's carburetor and fuel injectors clean, with smoother starts and dependable performance. 📋 Key Takeaways ✅ Direct OE Replacement: Replaces Mercury / Mariner part numbers 35-889527A07, 889527A07, 8M0111436, 87946A13 and 87946A15. ✅ Broad Fitment: Covers 6HP to 45HP outboards plus specialty variants like 10HP Sea Pro, Marathon and Viking, and 20HP JET. ✅ Oil-Resistant FKM Seal: Fluororubber seal resists oil and prevents hardening or cracking season after season. ✅ Engine Protection: High-efficiency media traps dirt, rust and impurities before they reach the carburetor and fuel injectors. ✅ Complete Kit: Filter assembly, steel ball, hose and cable ties — everything in one box, no extra parts needed. Features & Benefits Feature Benefit (What It Means for You) Fluororubber (FKM) Seal Resists oil and prevents hardening or cracking, maintaining a reliable leak-free seal even in saltwater and harsh marine environments where ordinary seals fail. High-Strength Plastic Housing Durable construction built for demanding engine compartments, standing up to heat, vibration and marine conditions. High-Efficiency Filter Media Traps dirt, rust and impurities to keep the carburetor and fuel injectors clean — supporting smoother starts and stable performance. 8 mm (5/16 in) Barbed Fittings Secure hose connections at the inlet and outlet prevent fuel line slippage, simplifying installation and service. Wide 6HP-45HP Fitment Covers the most common Mercury and Mariner outboard range, including hard-to-find parts for older and specialty models. Complete Kit Contents Includes the assembly, steel ball, hose and cable ties so you can complete the replacement in one go — no extra trips to the store. Compatibility & Cross-Reference Replaces OE Part Numbers: Interchange Part Number Brand FJ-WSFF11-ZH iFJF 35-889527A07 Mercury / Mariner OE 889527A07 Mercury / Mariner OE 8M0111436 Mercury / Mariner OE 87946A13 Mercury / Mariner OE 87946A15 Mercury / Mariner OE Compatible Filter Elements: 87946Q04, 896375K01, 896375Q01, 87946A3 Common Applications: Mercury / Mariner 6HP, 8HP, 9.9HP, 10HP, 15HP, 18HP, 20HP, 25HP, 35HP and 45HP outboard motors Specialty variants: 10HP Sea Pro, Marathon and Viking; 15HP Sea Pro and Marathon; 20HP JET Note: Please verify your engine model, year and original part number against the cross-reference table before ordering to ensure correct fitment. Specifications Part Number FJ-WSFF11-ZH (iFJF) Replaces 35-889527A07 / 889527A07 / 8M0111436 / 87946A13 / 87946A15 Filter Elements 87946Q04 / 896375K01 / 896375Q01 / 87946A3 Filter Type Fuel Filter Kit (inline, barbed fittings) Housing Material High-Strength Plastic Seal Material Fluororubber (FKM) Port Size 8 mm (5/16 in) barbed inlet & outlet Compatibility Mercury / Mariner 6HP-45HP outboards Package Includes 1 × filter assembly, 1 × steel ball, 1 × hose, 4 × cable ties Why Choose iFJF Over the OE Dealership? 🛡️ 1-Year Warranty Included · 30-Day Easy Returns · Lifetime Support Not satisfied? Return it. Fails prematurely? We'll replace it — no receipt-hoarding, no dealership runaround. As a professional filter manufacturer with a CNAS certified laboratory, we design and build our products to strictly match — and often exceed — OE specifications. Every single unit undergoes rigorous quality verification: 🔬 Lab-Tested Performance: Validated for filtration efficiency, particle holding capacity and burst strength. 🔍 100% Leakage Control: Factory-tested under high pressure to ensure zero leakage and secure field operation. 🛡️ Premium Build Quality: FKM seal and high-strength housing engineered for harsh marine environments. 💰 Factory-Direct Supply: Commercial-grade quality directly from the manufacturer, no middleman markup. ⭐ Parts in stock and ready to ship from our US warehouse. Frequently Asked Questions Q: Will this fuel filter kit fit my Mercury 9.9HP outboard motor? A: Yes. This kit is compatible with Mercury and Mariner outboard motors from 6HP to 45HP, which includes the 9.9HP model. It also covers specialty variants like the 10HP Sea Pro, Marathon and Viking, 15HP Sea Pro and Marathon, and 20HP JET. Please verify your engine model, year and part number before ordering. Q: Is this a complete kit or just the filter body? A: This is a complete kit that includes 1 fuel filter assembly, 1 steel ball, 1 hose and 4 cable ties, so everything needed for a replacement arrives in one box. No extra parts need to be purchased separately. Q: Is this a direct replacement for OEM part number 35-889527A07? A: Yes. This kit replaces part numbers 35-889527A07, 889527A07, 8M0111436, 87946A13 and 87946A15, plus filter elements 87946Q04, 896375K01, 896375Q01 and 87946A3. It is designed as a direct-fit replacement for the original part. Q: What material is the seal made of and will it leak in saltwater? A: The seal is made of fluororubber (FKM), which resists oil and prevents hardening or cracking over time. This helps maintain a reliable leak-free seal even in saltwater and harsh marine conditions. Q: Does this filter actually filter the fuel, or is it just a housing? A: This kit uses high-efficiency filter media that traps dirt, rust and impurities, helping keep the carburetor and fuel injectors clean. The housing is molded from high-strength plastic and is designed as a serviceable replacement part. Q: How hard is it to install? Make sure the engine is off and cool, and observe fuel safety precautions. Remove the old fuel filter assembly and disconnect the fuel line. Connect the new 8 mm barbed fittings to the fuel line and secure with the included cable ties. Install the steel ball and ensure all connections are tight. Prime the fuel system, start the engine and check carefully for leaks. Package Includes 1 × Fuel Filter Assembly 1 × Steel Ball 1 × Fuel Hose 4 × Cable Ties Common Problems with OE/Aftermarket Fuel Filters — Solved by iFJF We analyzed verified customer reviews of OE and aftermarket alternatives. Here's what outboard owners keep complaining about — and how we fixed it: ❌ What Owners Complain About ✅ How iFJF Solved It "The kit was missing parts like the gasket."— Common complaint in aftermarket reviews → Complete kit contentsEvery box includes the filter assembly, steel ball, hose and 4 cable ties — everything needed for the replacement, no missing pieces. "Not sure if it fits my Mercury outboard or if it's the right part number."— Common concern in Q&A and reviews → Explicit fitment + full OE cross-reference6HP-45HP fitment clearly listed with 5 OE part numbers and 4 filter elements — check your number against the Cross-Reference table before ordering. "Cheap seals crack and leak in saltwater after a season."— Common complaint in marine reviews → Fluororubber (FKM) sealOil-resistant FKM seal prevents hardening or cracking in harsh marine conditions — factory-direct value at a fraction of dealership pricing. 🔎 We read the 1-star and 2-star reviews so you don't have to. Every iFJF product is engineered to solve the real problems owners actually face — not just match a spec sheet. Factory Direct Supply & Wholesale — iFJF is a direct manufacturer of high-performance automotive and marine filtration products, backed by ISO 9001:2015 and IATF 16949:2016 quality management system certifications. Custom specifications and bulk orders are highly welcome. Contact us for exclusive dealer pricing and volume discounts. Email: support@ifjf.com

Read more less

Product Overview The iFJF RE551508 Fuel Filter Element is a direct-fit replacement for John Deere agricultural diesel engines. Designed for the 5E and 5M series utility tractors and other John Deere equipment, this filter element provides critical fuel system protection by removing water and contaminants before they reach sensitive injection components. Manufactured to IATF 16949 quality standards for the demanding conditions of modern farming operations. Key Features John Deere 5E/5M Series Fit: Direct replacement for RE551508 — fits 5085E, 5100E, 5085M, 5090M, 5100M, and 5115M utility tractor models. High-Efficiency Filtration: Removes water and microscopic contaminants from diesel fuel — essential protection for expensive common rail and mechanical injection systems. Farm-Ready Durability: Engineered to handle the dust, vibration, temperature swings, and long operating hours of agricultural field work. IATF 16949 Certified Manufacturing: Meets the same quality standards required by major equipment OEMs for their supply chain. Versatile Fleet Coverage: Compatible across multiple John Deere 5-Series models — simplify your parts inventory. Model Compatibility Series Compatible Models 5E Series (Utility) 5085E, 5090E, 5100E, 5105E 5M Series (Premium Utility) 5085M, 5090M, 5100M, 5115M Specifications Specification Detail Part Number RE551508 Filter Type Fuel Filter Element (Cartridge) Application John Deere 5E & 5M Series Diesel Tractors Fuel Type Diesel (Including Biodiesel up to B20) Certification IATF 16949 Maintenance Intervals Replace the fuel filter element every 400-500 hours of engine operation or annually, whichever comes first. For tractors operating in high-dust environments (tillage, harvesting) or using bulk fuel storage tanks, more frequent replacement at 250-300 hour intervals is recommended. Always drain the water separator before filter replacement and prime the fuel system after installation. Frequently Asked Questions Q: Will this fit my John Deere 5100E?A: Yes. The RE551508 is the correct fuel filter element for 5100E tractors and other 5E/5M series models listed in the compatibility table. Q: What's the difference between RE551508 and RE551507?A: Both are John Deere fuel filter elements but fit different filter housings. RE551508 is primarily for 5E/5M series tractors while RE551507 covers backhoes and dozers in addition to tractors. Q: How often should the fuel filter be changed on a tractor?A: Every 400-500 hours or annually. In dusty field conditions, change every 250-300 hours. Clean fuel is the cheapest insurance against injector failure. Q: Can I install this myself?A: Yes — fuel filter replacement is a standard maintenance task. Clean the housing thoroughly, replace all seals/O-rings, and prime the system before starting the engine. Q: Does this filter water in diesel fuel?A: Yes. The filter media is designed to separate both particulate contamination and water from diesel fuel — critical for protecting modern common rail injection systems. Related Products RE551507 Fuel Filter Element for John Deere MIU802421 Fuel Filter for John Deere 3E/4 Series

Read more less

Product OverviewUpgraded 3-inch mandrel-bent aluminum air intake elbow charge pipe for 1994-1998 Dodge Ram 2500/3500 with the 5.9L 12-valve Cummins. The restrictive factory intake elbow limits airflow and increases turbo lag. Our smooth-flowing 3-inch replacement improves airflow, reduces EGTs, and delivers crisper throttle response. Key Features 3-Inch Mandrel-Bent Flow: Smooth internal surface maximizes airflow for improved turbo spool and reduced EGTs under load. Aluminum Construction: Lightweight, corrosion-resistant with durable powder-coated finish. Direct Bolt-On: Factory mounting points — installs in ~30 minutes with basic hand tools. Compatibility Make Model Engine Year Dodge Ram 2500, Ram 3500 5.9L 12V Cummins 1994-1998 Specifications Specification Detail Material Mandrel-Bent Aluminum Diameter 3 Inches Application 1994-1998 Dodge Ram 5.9L 12V Cummins Installation Bolt-On ~30 Minutes Why Choose iFJFAt iFJF Direct, we supply diesel performance parts engineered for reliability. 1-year warranty. Fast US shipping. Frequently Asked QuestionsQ: Does this fit 24V (1998.5+) Cummins?A: No, this elbow is for 1994-1998 12-valve engines. 24V models use a different intake horn. Q: What is your return policy?A: 30-day return policy for unused items in original packaging. Contact us for replacement or refund. Q: How fast is shipping?A: Ships within 1-2 business days from US warehouse. Standard: 3-7 days. Q: Do you offer warranty?A: Yes, 1-year warranty against manufacturing defects. Order with ConfidenceUnlock your 12V's potential! Free shipping on orders $50+. Contact us for fitment questions.

Read more less

Product Overview Stop the notorious 6.7L Cummins coolant bypass hose leak permanently with this Billet Aluminum Coolant Bypass Hose Barb Adapter from iFJF. The OEM plastic barb fitting on 2009-2019 Ram 2500/3500 Cummins engines is a well-known weak point — repeated heat cycling causes the plastic to become brittle, crack, and eventually leak coolant. This can leave you stranded with an overheating engine. Our CNC-machined billet 6061-T6 aluminum adapter is a direct bolt-on replacement that eliminates this failure point for good. This is the adapter-only option — ideal if you already have replacement hoses and clamps on hand. The billet aluminum barb fitting is the critical upgrade; everything else can be sourced locally. Why the OEM Plastic Barb Fails The factory coolant bypass hose barb is made of glass-reinforced nylon plastic. While adequate when new, years of exposure to coolant at 190-210°F operating temperatures — combined with the constant vibration of the Cummins diesel engine — causes the plastic to degrade. The result is a sudden coolant leak that can rapidly drain your cooling system, leading to engine overheating and potential head gasket damage. This is one of the most common failure points on 2009-2019 Ram Cummins trucks. Key Features Billet 6061-T6 Aluminum Construction — CNC-machined from solid aerospace-grade aluminum for permanent durability Direct OEM Replacement — Same dimensions and fittings as the factory part; no modifications required Eliminates Plastic Barb Failure — No more cracked, brittle, or leaking OEM plastic fittings Corrosion-Resistant Finish — Engineered to withstand coolant exposure and engine bay conditions Precision CNC Machining — Tight tolerances ensure a perfect, leak-free seal with OEM hoses Lifetime Durability — Aluminum barb will outlast multiple OEM plastic replacements Compatibility Year Make Model Engine 2009-2018 Ram (Dodge) 2500 / 3500 6.7L Cummins Turbo Diesel 2019 Ram 2500 / 3500 6.7L Cummins Turbo Diesel Technical Specifications Specification Detail Material CNC-Machined Billet 6061-T6 Aluminum Finish Corrosion-Resistant Fitment 2009-2019 Ram 6.7L Cummins Installation Time 30-60 Minutes Installation Difficulty Intermediate (Basic Hand Tools) Frequently Asked Questions Q: Does this fix the common coolant leak on my 6.7L Cummins?A: Yes. The OEM coolant bypass hose uses a plastic barb fitting that becomes brittle over time and eventually cracks, causing a coolant leak. Our billet aluminum adapter permanently replaces this failure-prone plastic part. Q: Is installation difficult?A: Installation is straightforward for anyone with basic mechanical skills. It typically takes 30-60 minutes with common hand tools. You'll need to drain some coolant before removing the old fitting — always work on a cool engine. Q: Will this fit my 2009-2019 Ram 6.7L Cummins?A: Yes. This adapter fits all 2009 through 2019 Ram 2500 and 3500 trucks equipped with the 6.7L Cummins turbo diesel engine. Q: What material is the adapter made from?A: CNC-machined from billet 6061-T6 aluminum with a corrosion-resistant finish. Unlike the OEM plastic barb that degrades from heat cycling, our aluminum adapter will last the lifetime of your engine. Q: Do I need any special tools?A: Basic hand tools are all you need — socket set, pliers, flathead screwdriver, and a coolant catch pan. Some models may benefit from hose clamp pliers for tight spaces. Q: What's the difference between the adapter only and the complete kit?A: The adapter-only option includes just the billet aluminum barb fitting. The kit includes the adapter plus new hose clamps, O-rings, and replacement hose sections for a complete, leak-free installation. Why Choose iFJF? iFJF specializes in solving the common failure points on diesel trucks. Our coolant bypass adapter is engineered by diesel owners, for diesel owners — we understand what fails and how to fix it permanently. Every product is backed by our commitment to quality and responsive US-based customer support. You May Also Need Coolant Bypass Kit for 2003-2007 Ram 5.9L Cummins Coolant Bypass Hose Barb Adapter Kit — Complete Kit with Hoses

Read more less

Product Overview Stop the notorious 6.7L Cummins coolant bypass hose leak permanently with this Billet Aluminum Coolant Bypass Hose Barb Adapter from iFJF. The OEM plastic barb fitting on 2009-2019 Ram 2500/3500 Cummins engines is a well-known weak point — repeated heat cycling causes the plastic to become brittle, crack, and eventually leak coolant. This can leave you stranded with an overheating engine. Our CNC-machined billet 6061-T6 aluminum adapter is a direct bolt-on replacement that eliminates this failure point for good. This complete kit includes the billet aluminum barb adapter, new hose clamps, O-rings, and replacement hose sections for a comprehensive, leak-free installation. Why the OEM Plastic Barb Fails The factory coolant bypass hose barb is made of glass-reinforced nylon plastic. While adequate when new, years of exposure to coolant at 190-210°F operating temperatures — combined with the constant vibration of the Cummins diesel engine — causes the plastic to degrade. The result is a sudden coolant leak that can rapidly drain your cooling system, leading to engine overheating and potential head gasket damage. This is one of the most common failure points on 2009-2019 Ram Cummins trucks. Key Features Billet 6061-T6 Aluminum Construction — CNC-machined from solid aerospace-grade aluminum for permanent durability Direct OEM Replacement — Same dimensions and fittings as the factory part; no modifications required Eliminates Plastic Barb Failure — No more cracked, brittle, or leaking OEM plastic fittings Corrosion-Resistant Finish — Engineered to withstand coolant exposure and engine bay conditions Precision CNC Machining — Tight tolerances ensure a perfect, leak-free seal with OEM hoses Lifetime Durability — Aluminum barb will outlast multiple OEM plastic replacements Compatibility Year Make Model Engine 2009-2018 Ram (Dodge) 2500 / 3500 6.7L Cummins Turbo Diesel 2019 Ram 2500 / 3500 6.7L Cummins Turbo Diesel Technical Specifications Specification Detail Material CNC-Machined Billet 6061-T6 Aluminum Finish Corrosion-Resistant Fitment 2009-2019 Ram 6.7L Cummins Installation Time 30-60 Minutes Installation Difficulty Intermediate (Basic Hand Tools) Frequently Asked Questions Q: Does this fix the common coolant leak on my 6.7L Cummins?A: Yes. The OEM coolant bypass hose uses a plastic barb fitting that becomes brittle over time and eventually cracks, causing a coolant leak. Our billet aluminum adapter permanently replaces this failure-prone plastic part. Q: Is installation difficult?A: Installation is straightforward for anyone with basic mechanical skills. It typically takes 30-60 minutes with common hand tools. You'll need to drain some coolant before removing the old fitting — always work on a cool engine. Q: Will this fit my 2009-2019 Ram 6.7L Cummins?A: Yes. This adapter fits all 2009 through 2019 Ram 2500 and 3500 trucks equipped with the 6.7L Cummins turbo diesel engine. Q: What material is the adapter made from?A: CNC-machined from billet 6061-T6 aluminum with a corrosion-resistant finish. Unlike the OEM plastic barb that degrades from heat cycling, our aluminum adapter will last the lifetime of your engine. Q: Do I need any special tools?A: Basic hand tools are all you need — socket set, pliers, flathead screwdriver, and a coolant catch pan. Some models may benefit from hose clamp pliers for tight spaces. Q: What's the difference between the adapter only and the complete kit?A: The adapter-only option includes just the billet aluminum barb fitting. The kit includes the adapter plus new hose clamps, O-rings, and replacement hose sections for a complete, leak-free installation. Why Choose iFJF? iFJF specializes in solving the common failure points on diesel trucks. Our coolant bypass adapter is engineered by diesel owners, for diesel owners — we understand what fails and how to fix it permanently. Every product is backed by our commitment to quality and responsive US-based customer support. You May Also Need Coolant Bypass Kit for 2003-2007 Ram 5.9L Cummins Coolant Bypass Hose Barb Adapter Kit — Complete Kit with Hoses

Read more less