Search results for "fuel filter diesel"

Product Overview Keep your 3.0L EcoDiesel engine running clean and protected with the iFJF Oil Filter and Cap Assembly — a direct OEM-spec replacement for 2020-2021 Jeep Wrangler JL, Gladiator JT, and Ram 1500 DT models equipped with the 3.0L V6 diesel engine. This complete assembly includes both the high-efficiency filter element and the cap, ensuring a perfect seal and maximum filtration performance for your Gen 3 EcoDiesel. Key Features OEM-Spec Filtration Media: Multi-layer synthetic media captures 99% of contaminants as small as 25 microns, protecting your EcoDiesel's precision fuel system and turbocharger bearings from premature wear. Complete Assembly — Filter + Cap: Includes both the filter cartridge and cap, so you don't have to reuse a worn-out cap with degraded o-rings. One purchase, complete oil change. Direct Fit — No Modifications: Engineered to match the exact dimensions and thread pitch of the factory housing. Installs in minutes with basic hand tools. High-Capacity Design: Extended pleat surface area provides up to 10,000-mile service intervals under normal driving conditions (5,000 miles for severe duty). Compatible Part Numbers: Replaces OEM 68507598AA, 68498720AA. Compatibility Table Year Make Model Engine 2020-2021 Jeep Wrangler JL 3.0L EcoDiesel V6 2020-2021 Jeep Gladiator JT 3.0L EcoDiesel V6 2020-2021 Ram 1500 DT 3.0L EcoDiesel V6 Technical Specifications Specification Value OEM Part Numbers 68507598AA, 68498720AA Filter Type Cartridge (housing-style) Filtration Rating 25 micron (absolute) Material Synthetic blend media, composite cap Service Interval 7,500-10,000 miles (normal) Cap Thread Factory-matched Why Choose iFJF Oil Filters? The 3.0L EcoDiesel is a precision-engineered powerplant that demands premium filtration. Using a low-quality or worn-out oil filter can introduce contaminants that damage the high-pressure fuel pump, turbocharger, and bearing surfaces — repairs that can easily exceed $5,000. The iFJF oil filter and cap assembly provides OEM-level protection at a fraction of dealer pricing, giving you peace of mind every oil change. Frequently Asked Questions Q: Does this include the cap or just the filter?A: This is the complete assembly — both the filter cartridge AND the cap. If your old cap's o-ring is worn or the cap has been over-torqued, you get a fresh replacement included. Q: Will this fit a 2022 Jeep Wrangler EcoDiesel?A: This filter is specified for 2020-2021 models. 2022+ models may use a different filter housing design — please verify your OEM part number before ordering. Q: How often should I change the oil filter?A: Replace the filter with every oil change. For the EcoDiesel, we recommend 7,500-10,000 miles under normal conditions or 5,000 miles for severe duty (towing, off-roading, extreme temperatures). Q: Is this a genuine Mopar part?A: This is an OEM-spec aftermarket filter manufactured to meet or exceed Mopar specifications. It provides equivalent filtration performance for less. Q: What oil should I use with this filter?A: The Gen 3 EcoDiesel requires full synthetic 5W-40 diesel engine oil meeting API CK-4 or FCA MS-12991 specification. Call to Action Protect your EcoDiesel investment with proper filtration. Order the iFJF Oil Filter & Cap Assembly today with free shipping on orders $50+ across the USA. Related Products & Resources Shop All Oil Filters → Jeep Wrangler Parts & Accessories → Diesel Maintenance Guides →

Read more less

Fuel Filter Cap 1999-2003 Ford 7.3L Powerstroke F-250-550 Excursion Precision Fuel Filter Cap — OEM-Spec Fit Replace your worn or cracked fuel filter cap with this precision-engineered replacement for Ford 7.3L Powerstroke. Manufactured to exact OEM tolerances, this cap ensures a leak-proof seal that maintains proper fuel system pressure. Don't risk fuel leaks or air intrusion — a properly sealed filter cap is critical for reliable engine starting and operation. Key Features Leak-Proof Seal — Integrated O-ring groove ensures consistent sealing pressure across full temperature range OEM-Quality Construction — Manufactured to ISO/TS 16949 quality standards with 100% end-of-line testing Direct Fit — Precision-engineered to match OEM dimensions and mounting points — no modifications required Corrosion Resistant — Coated/plated components withstand diesel fuel, road salt, and moisture exposure Validated for Ford — Confirmed fitment across all listed applications Compatibility Make Engine Year Range Model Ford 7.3L Powerstroke 1999-2003 F-250/350/450/550 Ford 7.3L Powerstroke 2000-2003 Excursion Always verify fitment using the cross-reference part numbers below or contact our support team. Cross-Reference Part Numbers Brand Part Number Ford F81Z-9G270-BA Motorcraft FD-4596 Dorman 904-203 Dorman RK31449 Alliant 1831193C91 WIX 33830 Specifications Specification Value Part Number Fuel Brand iFJF Product Type Fuel Filter Cap Application 7.3L Powerstroke Vehicle Make Ford Material Steel/Plastic Composite Country of Origin China (ISO Certified) Warranty 1 Year / Unlimited Mileage Installation Guide Professional installation is recommended. Always refer to your vehicle or engine service manual for specific torque specifications and priming procedures. Replace all O-rings and seals during filter service — never reuse old seals. Maintenance Schedule Inspect during every filter service for signs of wear, cracking, or corrosion. Replace immediately if any damage is detected. Frequently Asked Questions Q: Is this an OEM or aftermarket fuel filter cap? This is a high-quality aftermarket replacement cap manufactured to exact OEM specifications for 7.3L Powerstroke. It provides the same fit, seal, and durability as the factory cap at a fraction of the dealer price. Q: Does the cap come with a new O-ring? Yes, this fuel filter cap includes a new Viton O-ring pre-installed for a leak-free seal. We recommend replacing the O-ring every time the filter is serviced. Q: What causes a fuel filter cap to fail? Fuel filter caps commonly fail due to over-torquing during installation (which cracks the plastic), UV/heat degradation of the plastic material, or O-ring deterioration causing air leaks. Q: How tight should I torque the fuel filter cap? Typically 25-35 Nm depending on your specific vehicle. Always refer to your service manual for the exact torque specification. Over-tightening is a leading cause of cap failure. Q: Will a bad fuel filter cap cause starting problems? Yes. A cracked or poorly sealed fuel filter cap can allow air into the fuel system, causing hard starts, rough running, and loss of prime — especially after the vehicle sits overnight. Related Products 🔗 Ford Parts & Filters 🔗 All Diesel Fuel Filters | All iFJF Products Related Blog Posts 📖 Complete Guide: When to Replace Your Diesel Fuel Filter 📖 5 Warning Signs Your Fuel Filter Is Clogged 📖 Ford Powerstroke Fuel System Maintenance

Read more less

Product Overview Keep your Ford Power Stroke running clean with this complete fuel filter kit for 2003-2010 Ford Super Duty trucks. This kit includes both filters needed for a full fuel system service: the HFCM (Horizontal Fuel Conditioning Module) filter on the frame rail AND the engine-mounted secondary filter under the hood. 6.0L and 6.4L Power Stroke fuel injectors operate at extreme pressures and tight tolerances. Contaminated fuel is the #1 cause of injector failure — a $3,000+ repair. Regular fuel filter changes are the cheapest insurance you can buy for your Power Stroke. Key Features Complete 2-Filter Kit — Includes HFCM frame-rail filter + engine-mounted fuel filter OEM-Grade Filtration — Meets Ford spec WSS-M2C942-A for 6.4L and OEM specs for 6.0L Water Separation — HFCM filter includes water-stripping coalescing media Includes O-Rings — All necessary seals for leak-free installation 15,000-Mile Interval — Matches Ford's recommended service schedule Compatibility Year Make Model Engine 2003–2007 Ford F-250 / F-350 / F-450 / F-550 Super Duty 6.0L Power Stroke 2008–2010 Ford F-250 / F-350 / F-450 / F-550 Super Duty 6.4L Power Stroke 2003–2005 Ford Excursion 6.0L Power Stroke 2004–2010 Ford E-350 / E-450 6.0L Power Stroke Cross-Reference Brand HFCM Filter Engine Filter Motorcraft FD-4615 FD-4616 Ford OEM 3C3Z-9N184-CA 4C3Z-9N184-AA Racor PFF-5486 PFF-5487 Why Regular Fuel Filter Changes Matter 6.0L injectors fire at up to 26,000 PSI — any contamination is catastrophic Water in fuel leads to injector tip erosion and internal corrosion A clogged HFCM filter restricts fuel flow, causing low power and hard starting Neglected fuel filters are the #1 misdiagnosis that leads to unnecessary injector replacement Frequently Asked Questions Q: How often should I change both fuel filters?A: Every 15,000 miles or 12 months. If you tow heavy, idle frequently, or use biodiesel, change every 10,000 miles. Always replace both filters together — the HFCM and engine filter work in series. Q: What's the difference between 6.0L and 6.4L fuel filters?A: The frames and fuel systems use different part numbers, but this kit covers BOTH engines. The HFCM filter design is the same; the engine-mounted filter differs between 6.0L (round cartridge) and 6.4L (specific design). Q: Will this fit a 2006 F-350 6.0L?A: Yes — this kit fits ALL 2003-2007 6.0L and 2008-2010 6.4L Super Duty trucks including F-250 through F-550. Q: Does the kit include the water separator drain O-ring?A: Yes, the necessary O-rings for the HFCM filter housing cap and drain plug are included. Installation Tips Remove HFCM filter first (frame rail under driver's door) — have a drain pan ready Clean HFCM housing thoroughly before installing new filter Replace engine-mounted filter second — access from top of engine bay Cycle key ON (not start) 6-8 times for 30 seconds each to prime fuel system Start engine and check for leaks at both filter housings Related Products Cummins FF266 Fuel Filter — For Dodge Ram 6.7L Browse All Diesel Fuel Filters Related Blog Posts Power Stroke 6.0L vs 6.4L: Maintenance Guide

Read more less

Product Overview The 6P3-WS24A-01 Fuel Filter for Yamaha V6 150-350HP Outboard — 2-Pack for Yamaha V6 150-350HP — 2-Pack is a premium-quality aftermarket replacement part engineered for compatible years compatible vehicles diesel engines vehicles. Designed to meet or exceed OEM specifications, this Fuel Filter delivers exceptional performance, durability, and reliability for compatible models owners who demand the best for their vehicles. Key Features Precision Engineering: Manufactured to exact OEM specifications using advanced CNC machining and rigorous quality control processes for perfect fitment every time. Premium Materials: Constructed from high-grade materials selected for maximum durability, corrosion resistance, and long service life under demanding conditions. Direct Fit Installation: Designed as a direct bolt-on replacement with no modifications required — simply remove the old part and install this one using basic hand tools. Quality Certified: Backed by IATF 16949 certified manufacturing standards, ensuring consistent quality and reliability across every unit produced. Comprehensive Warranty: Covered by iFJF's standard warranty against manufacturing defects, with dedicated customer support available to answer your questions. Compatibility Specification Details Vehicle Make compatible vehicles Vehicle Models compatible models Year Range compatible years Engine diesel engines Part Number 6P3-WS24A-01 Fuel Filter for Yamaha V6 150-350HP Outboard — 2-Pack Replaces OEM OEM specifications Why Choose iFJF Direct? At iFJF Direct, we specialize in providing diesel enthusiasts and professional mechanics with premium aftermarket parts that deliver genuine value. Every product we sell is carefully selected for quality, tested for performance, and backed by our commitment to customer satisfaction. Whether you're maintaining a daily driver, building a competition truck, or servicing a fleet, iFJF has the parts you need with the quality you can trust. Frequently Asked Questions Q: Will this fit my compatible years? A: This Fuel Filter is designed for compatible years compatible vehicles compatible models with the diesel engines. Please verify your vehicle's year, make, model, and engine match the compatibility table above. If you're unsure, contact our support team with your VIN for confirmation. Q: How often should I replace this Fuel Filter? A: We recommend replacing your Fuel Filter every 15,000 to 30,000 miles under normal driving conditions. If you tow heavy loads, idle frequently, operate in dusty environments, or run biodiesel blends, replace it every 10,000 to 15,000 miles. Regular replacement protects your fuel system and maintains optimal engine performance. Q: Is this an OEM part or aftermarket? A: This is a premium aftermarket Fuel Filter manufactured to IATF 16949 certified standards and engineered to meet or exceed OEM specifications. It replaces OEM part numbers OEM specifications and delivers equivalent or superior performance at a more competitive price. Q: What is included in the kit? A: This kit includes the Fuel Filter with all necessary seals, gaskets, and O-rings for a complete and proper installation. You will need basic hand tools — no special tools are required for most applications. Q: What is your return and warranty policy? A: All iFJF products come with a warranty against manufacturing defects. If you receive a defective product, contact our support team with your order number for a replacement or refund. We stand behind every product we sell. Order With Confidence When you order from iFJF Direct, you're getting more than just a Fuel Filter — you're getting our commitment to quality, reliability, and customer satisfaction. Every product is backed by our warranty and supported by our knowledgeable customer service team. Order yours today and experience the iFJF difference! 📚 Related Guides & Articles Get the most out of your purchase with these helpful resources: Marine Fuel Water Separator Guide: Why Your Outboard Needs One and How to Choose R12T Marine Fuel Filter Installation Guide: NPT & ZG1/4-19 Fittings, Torque Specs

Read more less

Product Overview The iFJF LF17511 Oil Filter is a premium heavy-duty replacement filter engineered for Detroit Diesel DD13, DD15, and DD16 engines. Designed for the demanding conditions of commercial trucking — including Freightliner Cascadia, Western Star, and heavy vocational applications — this filter delivers exceptional oil filtration and engine protection under high-load, long-haul operating conditions. Manufactured to IATF 16949 quality standards. Key Features Heavy-Duty Synthetic Blend Media: High-capacity filtration traps contaminants as small as 25 microns while maintaining optimal oil flow — critical for 12.8L-15.6L engine protection. DD13/DD15/DD16 Compatibility: Precision-engineered to fit Detroit Diesel engines across Cascadia, Western Star 5700XE, and Freightliner M2 112 platforms. Anti-Drainback Valve: Prevents dry starts by keeping oil in the filter when the engine is off — essential for long-haul truck engine longevity. High-Burst-Strength Canister: Reinforced steel housing withstands the high oil pressures common in Detroit Diesel HDEP engines. IATF 16949 Certified: Meets or exceeds OEM specifications for fit, filtration efficiency, and durability under extreme operating conditions. Vehicle Compatibility Engine Displacement Vehicle Applications Detroit DD13 12.8L Freightliner Cascadia, M2 112, Western Star 4700 Detroit DD15 14.8L Freightliner Cascadia, Western Star 4900/5700XE Detroit DD16 15.6L Freightliner Cascadia, Western Star 4900/6900 Specifications Specification Detail Part Number LF17511 Filter Type Full-Flow Spin-On Oil Filter Filtration Efficiency ~25 Micron Nominal Thread Size Standard Detroit Diesel Spin-On Anti-Drainback Valve Yes Certification IATF 16949 Maintenance Interval Detroit Diesel recommends oil and filter changes based on duty cycle. Under normal highway operation: every 25,000-50,000 miles. Severe service (vocational, stop-and-go, extreme temperatures) requires more frequent changes. Always consult your owner's manual and follow fleet maintenance schedules. Frequently Asked Questions Q: Will this fit my 2018 Cascadia with DD15?A: Yes. The LF17511 is the correct oil filter for all DD15 engines used in Freightliner Cascadia models from 2010 to present. Q: Is this an OEM Detroit Diesel filter?A: This is a premium aftermarket filter manufactured to meet or exceed OEM specifications. It is IATF 16949 certified, the same quality standard used by major OEM suppliers. Q: How often should I change this filter?A: Replace with every oil change — typically 25,000-50,000 miles under normal highway conditions. Severe-duty applications should follow shorter intervals. Q: Does this filter have an anti-drainback valve?A: Yes. The built-in anti-drainback valve prevents oil from draining out of the filter when the engine is off, ensuring immediate oil pressure on startup. Q: Does it fit DD13 and DD16 engines too?A: Yes. The LF17511 fits DD13 (12.8L), DD15 (14.8L), and DD16 (15.6L) Detroit Diesel engines. Related Products R61709 Fuel Filter Water Separator for DD13/DD15/DD16 PF9804 Fuel Water Separator for DD13/DD15/DD16

Read more less

placeholder

Read more less

Product Overview The 2-Pack FS1098 Fuel Water Separator for Cummins B6.7 / ISL8.9 delivers professional-grade fuel filtration for diesel engines. Manufactured with advanced synthetic media for superior contaminant capture and water separation, this filter protects your high-pressure common rail injection system from the microscopic particles and moisture that cause premature injector and pump failure. As diesel injection pressures climb past 30,000 PSI in modern engines, fuel cleanliness has never been more critical. A single tank of contaminated fuel can cause thousands in injector damage. This filter provides the first and most important line of defense for your fuel system. Key Features High-Efficiency Filtration Media: Multi-layer synthetic media captures 99.9% of particles at the rated micron level, exceeding standard cellulose elements in both efficiency and dirt-holding capacity. Advanced Water Separation: Coalescing technology removes emulsified and free water from diesel fuel, preventing injector tip erosion and microbial growth. OEM-Spec Construction: Manufactured to ISO 9001 quality standards with precision-threaded base plate, anti-drain back valve, and high-burst-strength canister. Direct Fit Replacement: Engineered as a drop-in replacement — no modifications, adapters, or special tools required. Extended Service Life: Higher dirt-holding capacity means longer intervals between changes, reducing downtime and per-mile filtration costs. Compatibility Specification Detail Engine Cummins B6.7, ISL8.9, L9 Diesel Application Commercial Trucks, RVs, Buses Replaces Part # FS1098, 5319680, 5308722 Micron Rating 2-10 Micron Absolute Filter Type Spin-On with Water Separation Why Upgrade Your Fuel Filtration? Extended Injector Life: Injectors operating at 30,000+ PSI have micron-level clearances. Better filtration means injectors lasting 200K+ miles instead of failing at 100K. Improved Cold-Weather Reliability: Superior water separation prevents ice crystal formation in fuel lines during winter. Reduced Maintenance Costs: Preventing one HPFP failure saves $5,000-$10,000 — the cost of a lifetime of premium filters. Better Fuel Economy: Clean injectors atomize fuel more efficiently, maintaining optimal combustion over the vehicle lifetime. Installation Guide Safety First: Park on level ground, engage parking brake, allow engine to cool. Have a drain pan ready. Relieve Fuel Pressure: Remove fuel cap. On some models, pull fuel pump fuse and crank briefly. Remove Old Filter: Use oil filter wrench to loosen. Unscrew by hand and lower into drain pan. Prep New Filter: Apply thin film of clean diesel to gasket. Pre-fill if housing design allows. Install: Spin on by hand until gasket contacts. Tighten 3/4 to 1 full turn. DO NOT over-tighten with wrench. Prime System: Cycle key ON (not START) 5-6 times for 30 seconds each to purge air. Check for leaks. Start & Verify: Start engine, check for leaks at idle, let run 2 minutes, recheck. Dispose of old filter properly. Frequently Asked Questions Q: What engines does this fit?A: Fits Cummins B6.7, ISL8.9, and L9 diesel engines in Freightliner M2, International MV, Blue Bird Vision buses, motorhomes, and commercial vehicles from 2010-present. Replaces OEM part numbers 5319680 and 5308722. Q: How is this different from the fuel filter?A: FS1098 is a fuel water separator — it removes water, sediment, and larger particles BEFORE fuel enters the main filter. This 2-stage filtration protects the high-pressure common rail system. Replace both filters together. Q: What micron rating?A: 10-micron nominal filtration with 98% water separation efficiency. Integrated PCV (pressure control valve) maintains consistent fuel pressure. Exceeds OEM water removal performance. Q: How often should I drain the water separator?A: Drain the water bowl weekly during regular operation or when the WIF (Water-In-Fuel) warning light illuminates. For sitting vehicles, drain monthly. Water accumulation is higher in humid climates and with biodiesel blends above B5. Q: Can I use this on my RV Cummins generator?A: Yes. If your RV has a Cummins Onan generator with B6.7 or ISL engine platform, this is a direct fit. Verify generator model number — common on class A diesel pushers with Onan QD series. Related Products Shop All Fuel Filters & Water Separators → Diesel Engine Oil Filters → Air Filters — Complete Intake Protection → Related Guides & Articles Diesel Fuel System Maintenance: Complete Guide → How to Prevent Diesel Fuel Contamination → Common Rail Diesel Injector Failure: Warning Signs → 📖 Related Guide: Read our complete installation guide and comparison →

Read more less

Premium Oil Filtration for Cummins Compact Diesels The LF16352 spin-on oil filter is the standard lube filter for Cummins ISF 3.8L and QSF 2.8L diesel engines — the compact powerplants found in delivery trucks, marine auxiliaries, construction equipment, and agricultural machinery. Our replacement filter meets or exceeds OEM filtration specifications to protect your engine's bearings, turbocharger, and hydraulic systems from oil-borne contaminants. Why Oil Filtration Matters for Small Diesels Compact diesel engines like the ISF3.8 and QSF2.8 run at higher RPM than their big-bore counterparts, generating more oil shear and contaminants per displacement. A high-quality oil filter with consistent micron rating is essential for maintaining oil pressure, preventing turbo bearing wear, and extending oil change intervals. Compatibility Engine Displacement Application Cummins ISF 3.8 3.8L I4 Delivery trucks, buses, construction equipment Cummins QSF 2.8 2.8L I4 Marine auxiliary, compact construction, ag equipment Cross-Reference Part Numbers: Fleetguard LF16352, Donaldson P556352, Baldwin B40050, Sakura SO10116, Mann SP96023 Specifications Specification Detail Type Spin-on full-flow lube oil filter Micron Rating 15 micron nominal — ≥95% efficiency Thread Size Standard metric — direct spin-on replacement Anti-Drain Back Valve Yes — silicone valve prevents dry starts Bypass Valve Yes — integrated pressure relief for cold starts Gasket Pre-lubricated nitrile rubber — no leaks, easy removal Why Choose iFJF? OEM-equivalent filtration — 15-micron efficiency matches Fleetguard LF16352 specs Silicone anti-drain valve — Superior to rubber — stays flexible in cold weather Heavy-duty canister — Burst-tested to 5x rated operating pressure Pre-lubed gasket — Easy spin-on, easy spin-off at next oil change Universal fit — Cross-references to 6+ major filter brands Frequently Asked Questions Q: What's the oil change interval with this filter?A: Cummins recommends oil changes every 500 hours or 6 months for ISF3.8/QSF2.8 engines under normal operating conditions. Severe duty (high dust, high idle time) requires more frequent changes — consult your equipment manual. Q: Does this filter have a bypass valve?A: Yes. An internal bypass valve opens at approximately 12-15 PSI differential pressure to ensure oil flow during cold starts or if the filter becomes clogged. The anti-drain back valve keeps oil in the filter when the engine is off for instant pressure on startup. Q: Is this filter suitable for marine use?A: Yes. The filter is compatible with QSF2.8 marine auxiliary engines. Always follow your marine engine manufacturer's oil specification and change interval recommendations. Q: How does this compare to the Fleetguard LF16352?A: This filter is manufactured to the same 15-micron filtration standard as the Fleetguard OEM filter. It features equivalent media area, bypass valve calibration, and anti-drain valve performance. Q: Can I use this on a Cummins ISB or ISC engine?A: No. The LF16352 is designed specifically for ISF3.8 and QSF2.8 engines. Larger engines (ISB, ISC, ISL, ISX) require different filter models. Always verify the part number against your engine's manual.

Read more less

Product Overview The 68F-24563-10 Fuel Filter for Yamaha 150-300HP Outboard — 2-Pack is a premium-quality aftermarket replacement part engineered for 4563-10 compatible vehicles diesel engines vehicles. Designed to meet or exceed OEM specifications, this Fuel Filter delivers exceptional performance, durability, and reliability for compatible models owners who demand the best for their vehicles. Key Features Precision Engineering: Manufactured to exact OEM specifications using advanced CNC machining and rigorous quality control processes for perfect fitment every time. Premium Materials: Constructed from high-grade materials selected for maximum durability, corrosion resistance, and long service life under demanding conditions. Direct Fit Installation: Designed as a direct bolt-on replacement with no modifications required — simply remove the old part and install this one using basic hand tools. Quality Certified: Backed by IATF 16949 certified manufacturing standards, ensuring consistent quality and reliability across every unit produced. Comprehensive Warranty: Covered by iFJF's standard warranty against manufacturing defects, with dedicated customer support available to answer your questions. Compatibility Specification Details Vehicle Make compatible vehicles Vehicle Models compatible models Year Range 4563-10 Engine diesel engines Part Number 68F-24563-10 Fuel Filter Replaces OEM OEM specifications Why Choose iFJF Direct? At iFJF Direct, we specialize in providing diesel enthusiasts and professional mechanics with premium aftermarket parts that deliver genuine value. Every product we sell is carefully selected for quality, tested for performance, and backed by our commitment to customer satisfaction. Whether you're maintaining a daily driver, building a competition truck, or servicing a fleet, iFJF has the parts you need with the quality you can trust. Frequently Asked Questions Q: Will this fit my 4563-10? A: This Fuel Filter is designed for 4563-10 compatible vehicles compatible models with the diesel engines. Please verify your vehicle's year, make, model, and engine match the compatibility table above. If you're unsure, contact our support team with your VIN for confirmation. Q: How often should I replace this Fuel Filter? A: We recommend replacing your Fuel Filter every 15,000 to 30,000 miles under normal driving conditions. If you tow heavy loads, idle frequently, operate in dusty environments, or run biodiesel blends, replace it every 10,000 to 15,000 miles. Regular replacement protects your fuel system and maintains optimal engine performance. Q: Is this an OEM part or aftermarket? A: This is a premium aftermarket Fuel Filter manufactured to IATF 16949 certified standards and engineered to meet or exceed OEM specifications. It replaces OEM part numbers OEM specifications and delivers equivalent or superior performance at a more competitive price. Q: What is included in the kit? A: This kit includes the Fuel Filter with all necessary seals, gaskets, and O-rings for a complete and proper installation. You will need basic hand tools — no special tools are required for most applications. Q: What is your return and warranty policy? A: All iFJF products come with a warranty against manufacturing defects. If you receive a defective product, contact our support team with your order number for a replacement or refund. We stand behind every product we sell. Order With Confidence When you order from iFJF Direct, you're getting more than just a Fuel Filter — you're getting our commitment to quality, reliability, and customer satisfaction. Every product is backed by our warranty and supported by our knowledgeable customer service team. Order yours today and experience the iFJF difference! 📚 Related Guides & Articles Get the most out of your purchase with these helpful resources: Marine Fuel Water Separator Guide: Why Your Outboard Needs One and How to Choose R12T Marine Fuel Filter Installation Guide: NPT & ZG1/4-19 Fittings, Torque Specs

Read more less

Fuel Return Connector for 2017-2020 Ford 6.7L Powerstroke F-250-550 OEM-Spec Fuel Return Connector Replace your brittle or leaking fuel return line connector with this precision-molded replacement for 6.7L Powerstroke. Manufactured from high-temperature ABS plastic with OEM-spec quick-disconnect fittings. A leaking return connector can cause hard starts, fuel odor, and reduced efficiency — this direct-fit replacement restores factory sealing integrity. Key Features High-Temp ABS Plastic — Withstands under-hood temperatures without brittleness OEM-Quality Construction — Manufactured to ISO/TS 16949 quality standards with 100% end-of-line testing Direct Fit — Precision-engineered to match OEM dimensions and mounting points — no modifications required Corrosion Resistant — Coated/plated components withstand diesel fuel, road salt, and moisture exposure Validated for Ford — Confirmed fitment across all listed applications Compatibility Make Engine Year Range Model Ford 6.7L Powerstroke 2017-2020 F-250/350/450/550 Super Duty Always verify fitment using the cross-reference part numbers below or contact our support team. Cross-Reference Part Numbers Brand Part Number Ford HC3Z-9A564-A Motorcraft FD-4625 Dorman 904-309 Specifications Specification Value Part Number Fuel Brand iFJF Product Type Fuel Filter Parts Application 6.7L Powerstroke Vehicle Make Ford Material Steel/Plastic Composite Country of Origin China (ISO Certified) Warranty 1 Year / Unlimited Mileage Installation Guide Professional installation is recommended. Always refer to your vehicle or engine service manual for specific torque specifications and priming procedures. Replace all O-rings and seals during filter service — never reuse old seals. Maintenance Schedule Inspect during every filter service for signs of wear, cracking, or corrosion. Replace immediately if any damage is detected. Frequently Asked Questions Q: Is this compatible with my 6.7L Powerstroke fuel system? Yes, this component is designed for 6.7L Powerstroke fuel systems and matches OEM specifications for fit and function. Q: Is professional installation recommended? Installation is straightforward for experienced DIY mechanics with basic hand tools. However, since this is a fuel system component, proper installation is critical to prevent leaks. Q: What material is used in construction? Manufactured from high-grade materials rated for diesel fuel exposure and under-hood/under-vehicle conditions. Corrosion-resistant coating ensures long service life. Q: Do you offer a warranty? Yes, all iFJF products are backed by a 1-year warranty against manufacturing defects. Q: How fast is shipping? All orders ship from our US warehouse within 1-2 business days. Standard shipping is 3-7 business days. Expedited options are available at checkout. Related Products 🔗 Ford Parts & Filters 🔗 All Diesel Fuel Filters | All iFJF Products Related Blog Posts 📖 Ford Powerstroke Fuel System Maintenance

Read more less

Product Overview The F1810PM0 Fuel Filter Element is a high-flow spin-on particulate filter designed for industrial and agricultural fuel transfer systems. With an 18 GPM flow rate and 10 micron nominal filtration, it's built for the demanding duty cycle of bulk diesel and gasoline transfer — protecting downstream equipment from rust, scale, and debris. Direct replacement for 1200KTG9075 filter head assemblies with 1-12UN thread pattern. Key Features High-Flow Design — 18 GPM: Supports bulk fuel transfer pumps up to 18 GPM without excessive pressure drop. Ideal for farm fuel tanks, construction site refueling, and marina diesel systems. 10 Micron Particulate Filtration: Removes rust, scale, sand, and debris common in bulk storage tanks. Extends the life of secondary filters and protects fuel injection components. 1-12UN Thread: Standard industrial thread pattern fits 1200KTG9075 and compatible filter heads. Quick spin-on/spin-off replacement — no tools required. Carbon Steel Canister: Heavy-gauge carbon steel construction with corrosion-resistant coating. Built for outdoor and shop-floor durability. Multi-Fuel Compatible: Diesel, gasoline, biodiesel (B5-B20), kerosene, and heating oil. Wide chemical compatibility for mixed-fuel operations. Compatibility Component Compatible Models Filter Head 1200KTG9075 Series Thread 1-12UN (1 inch, 12 threads per inch, Unified National) Cross Reference Goldenrod 496-5 compatible (verify dimensions) Specifications Specification Value Part Number FJ-7018-LX Filter Type Spin-On Particulate (Full-Flow) Micron Rating 10 Micron Nominal Flow Rate 18 GPM (68 L/min) Thread Size 1-12UN Canister Material Carbon Steel with Anti-Corrosion Coating Fuel Compatibility Diesel, Gasoline, Biodiesel (B5-B20), Kerosene Applications Farm Fuel Transfer: Bulk diesel/gasoline transfer from storage tanks to tractors, combines, and equipment Construction Refueling: On-site diesel transfer for excavators, dozers, and generators Marina Fuel Systems: Marine diesel transfer and polishing systems Fleet Fueling: Shop-based fuel dispensing for truck and equipment fleets Frequently Asked Questions Q: What filter head does this fit?A: This F1810PM0 element is designed for the 1200KTG9075 series filter head with 1-12UN threads. It also fits compatible heads using the 1-12UN thread pattern (common on industrial and agricultural diesel transfer systems).Q: What micron rating is this filter?A: 10 micron nominal particulate filtration. Suitable for primary or secondary fuel filtration on diesel transfer pumps, bulk tank systems, and agricultural refueling setups. For final filtration before injection pumps, pair with a 2-5 micron secondary filter.Q: What's the flow rate?A: 18 gallons per minute (GPM) rated flow. This high-flow element is designed for bulk fuel transfer and high-volume refueling operations — not for small consumer pumps that may not produce adequate pressure differential.Q: Can this be used with gasoline?A: Yes. The F1810PM0 element is compatible with diesel, gasoline, biodiesel (up to B20), kerosene, and heating oil. Carbon steel canister with corrosion-resistant coating.

Read more less

Product Overview The 6P3-24560-03 Filter Assembly for Yamaha F200-F250 Outboard is a premium-quality aftermarket replacement part engineered for 4560-03 compatible vehicles diesel engines vehicles. Designed to meet or exceed OEM specifications, this Fuel Filter Assembly delivers exceptional performance, durability, and reliability for compatible models owners who demand the best for their vehicles. Key Features Precision Engineering: Manufactured to exact OEM specifications using advanced CNC machining and rigorous quality control processes for perfect fitment every time. Premium Materials: Constructed from high-grade materials selected for maximum durability, corrosion resistance, and long service life under demanding conditions. Direct Fit Installation: Designed as a direct bolt-on replacement with no modifications required — simply remove the old part and install this one using basic hand tools. Quality Certified: Backed by IATF 16949 certified manufacturing standards, ensuring consistent quality and reliability across every unit produced. Comprehensive Warranty: Covered by iFJF's standard warranty against manufacturing defects, with dedicated customer support available to answer your questions. Compatibility Specification Details Vehicle Make compatible vehicles Vehicle Models compatible models Year Range 4560-03 Engine diesel engines Part Number 6P3-24560-03 Filter Assembly Replaces OEM OEM specifications Why Choose iFJF Direct? At iFJF Direct, we specialize in providing diesel enthusiasts and professional mechanics with premium aftermarket parts that deliver genuine value. Every product we sell is carefully selected for quality, tested for performance, and backed by our commitment to customer satisfaction. Whether you're maintaining a daily driver, building a competition truck, or servicing a fleet, iFJF has the parts you need with the quality you can trust. Frequently Asked Questions Q: Will this fit my 4560-03? A: This Fuel Filter Assembly is designed for 4560-03 compatible vehicles compatible models with the diesel engines. Please verify your vehicle's year, make, model, and engine match the compatibility table above. If you're unsure, contact our support team with your VIN for confirmation. Q: How often should I replace this Fuel Filter Assembly? A: We recommend replacing your Fuel Filter Assembly every 15,000 to 30,000 miles under normal driving conditions. If you tow heavy loads, idle frequently, operate in dusty environments, or run biodiesel blends, replace it every 10,000 to 15,000 miles. Regular replacement protects your fuel system and maintains optimal engine performance. Q: Is this an OEM part or aftermarket? A: This is a premium aftermarket Fuel Filter Assembly manufactured to IATF 16949 certified standards and engineered to meet or exceed OEM specifications. It replaces OEM part numbers OEM specifications and delivers equivalent or superior performance at a more competitive price. Q: What is included in the kit? A: This kit includes the Fuel Filter Assembly with all necessary seals, gaskets, and O-rings for a complete and proper installation. You will need basic hand tools — no special tools are required for most applications. Q: What is your return and warranty policy? A: All iFJF products come with a warranty against manufacturing defects. If you receive a defective product, contact our support team with your order number for a replacement or refund. We stand behind every product we sell. Order With Confidence When you order from iFJF Direct, you're getting more than just a Fuel Filter Assembly — you're getting our commitment to quality, reliability, and customer satisfaction. Every product is backed by our warranty and supported by our knowledgeable customer service team. Order yours today and experience the iFJF difference! 📚 Related Guides & Articles Get the most out of your purchase with these helpful resources: Marine Fuel Water Separator Guide: Why Your Outboard Needs One and How to Choose R12T Marine Fuel Filter Installation Guide: NPT & ZG1/4-19 Fittings, Torque Specs

Read more less