Home & Garden Home & Garden

Home & Garden

Home & Garden Essentials From garden tools and outdoor equipment to home improvement supplies, iFJF Direct carries a practical select...

171 products


  • 88624000 Kitchen Faucet Pull-Down Spray Hose for Hansgrohe — Replaces 95507000 - Image 1

    iFJF iFJF 88624000 Kitchen Faucet Hose Part for Hansgrohe Pull down Spray Hose 95507000

    iFJF 88624000 Pull-Down Spray Hose — Hansgrohe Kitchen Faucet Replacement When your Hansgrohe kitchen faucet spray head loses pressure, drips from the hose, or the hose shows signs of cracking and wear, don't replace the entire faucet — replace just the hose. The iFJF 88624000 pull-down spray hose is a direct replacement for Hansgrohe part numbers 88624000 and 95507000, restoring full water pressure and smooth spray head retraction. At a fraction of the OEM price, this hose gives your premium faucet a second life. Key Features & Benefits Direct Hansgrohe Replacement Compatible with all standard (non-Select) Hansgrohe pull-down kitchen faucets. The quick-connect fittings match the original exactly — no adapters, no leaks. Unscrew the old hose, click in the new one, and you're done in 10 minutes. Durable Braided Construction The hose features a reinforced braided nylon exterior over an inner tube rated for continuous hot and cold water use. The braided jacket resists kinking, abrasion, and the daily pull-down/push-up wear that eventually wears out factory hoses. 60-Inch Extended Reach At 60 inches, the hose provides ample length for filling pots, rinsing the sink, and cleaning around the kitchen. The weight-assisted retraction mechanism (reuse your existing weight) pulls the spray head smoothly back into the faucet spout. Technical Specifications Specification Detail Model iFJF 88624000 Replaces OEM Hansgrohe 88624000, 95507000 Length 60 inches Material Braided Nylon + Inner Tube Connection Quick-Connect / Threaded Compatibility Hansgrohe Standard Pull-Down Faucets Compatible Hansgrohe Faucet Lines Hansgrohe Allegro (standard, non-Select) Hansgrohe Talis (select models) Hansgrohe Metris (non-Select) Hansgrohe Focus (non-Select) Hansgrohe Cento Other standard Hansgrohe pull-down kitchen faucets Note: Does not fit Hansgrohe Select models with the button-controlled spray mode selector. Verify your faucet model before ordering. Installation Turn off water supply valves under the sink. Unscrew the spray head from the old hose. Pull the old hose out through the faucet spout. Disconnect the old hose from the supply line under the sink (quick-connect clip or threaded connection). Feed the new hose down through the faucet spout. Connect to the supply line fitting. Attach the spray head to the new hose. Reattach the weight (from the old hose) at the marked position. Turn water back on and test for leaks and smooth spray head operation. Frequently Asked Questions How do I know if this hose fits my Hansgrohe faucet? If your Hansgrohe faucet has a pull-down spray head (not a side spray) and is not a "Select" model with electronic spray mode switching, this hose will fit. The connecting fittings match the standard Hansgrohe quick-connect design used across most non-Select models. Does this hose include the spray head? No, this listing is for the replacement hose only. The spray head is sold separately if you need to replace that as well. Most Hansgrohe spray heads can be unscrewed and reattached to the new hose. Will this hose kink easily? The braided nylon jacket is specifically designed to resist kinking and tangling. The hose has enough flexibility to move freely inside the faucet body while maintaining full water flow even when pulled to its full 60-inch extension. Is this hose rated for hot water? Yes. The inner tube and braided jacket are rated for continuous use with water temperatures up to 160°F (71°C), making it suitable for standard kitchen hot water use. Related Products iFJF 88624000 Pull-Down Spray Hose Kitchen Parts Collection Faucet Parts Collection

    $29.99

  • SFX1000 SFX1500 Skimmer to Sand Pump Conversion Kit for Above Ground Pool

    iFJF SFX1000/SFX1500 Skimmer to Sand Pump Conversion Kit

    SFX1000/SFX1500 Skimmer Pump to Sand Pump Conversion Kit Product Overview Upgrade your pool filtration system with this iFJF conversion kit. Specifically designed to convert SFX1000 and SFX1500 skimmer pumps into sand pump-compatible equipment — no need to replace your entire filtration setup. Key Features Wide Compatibility: Works with SFX1000 and SFX1500 skimmer pump models across a range of above-ground pool brands. Improved Water Circulation: Enhances your pool's filtration efficiency by enabling sand pump integration for cleaner, safer swimming water. Dual-Seal Design: Features an O-ring gasket plus threaded tape seal — ensure the O-ring is fully seated in the groove and apply thread tape for a leak-free connection. Easy DIY Installation: Simply remove the bottom pump motor, attach the hose to the internal unit seal, and screw the conversion part onto the bottom of the tank. No professional tools required. Durable Construction: Manufactured from high-grade materials built to withstand continuous pump operation and pool chemical exposure. Compatibility Compatible Models: SFX1000, SFX1500 skimmer pump systems Converts to: Standard sand pump-compatible equipment Application: Above-ground swimming pool filtration systems What's Included 1 × Skimmer Pump Conversion Kit (SFX1000/SFX1500) 1 × O-Ring Gasket (pre-installed) Important Notes This is a conversion part only — not a complete pump replacement. Ensure the O-ring gasket is fully seated in the groove before tightening to prevent leaks. Use PTFE thread tape on all threaded connections for optimal sealing. FAQ Q: Will this work with my pool pump?A: This kit is compatible with SFX1000 and SFX1500 skimmer pump models. Please verify your pump model before ordering. Q: Is professional installation required?A: No, it's designed for DIY installation with basic tools. Most users complete installation in under 30 minutes. Factory Direct Supply -- iFJF manufactures its own pool replacement parts. Bulk orders are welcome. Contact us for wholesale pricing and volume discounts. Email: support@ifjf.net Related Products Pool Plunger Valve Assembly Pool Filter Drain Plug 6-Pack Pool Pipe Support w/Plunger Valve Pool Inlet Strainer Kit Related Guide Read: Convert Your Intex Skimmer Pool to a Sand Filter System: SFX1000/SFX1500 Kit Install in 30 Minutes

    $33.99

  • 2" MIP x 2" PVC Hi-Temp Unions for WhisperFlo & IntelliFlo Pool Pumps  — main product view

    iFJF 2" MIP x 2" PVC Hi-Temp Unions for WhisperFlo & IntelliFlo Pool

    2" MIP x 2" PVC Hi-Temp Unions for WhisperFlo & IntelliFlo P — Pool Equipment Replacement Built to Last Keep your pool or spa running efficiently with this precision-engineered replacement component from iFJF. Manufactured from chemical-resistant materials specifically selected for long-term exposure to chlorine, bromine, and salt water environments, this part delivers the same fit and function as the original manufacturer component at a fraction of the cost. Whether repairing a leaking valve, upgrading worn-out fittings, or performing seasonal maintenance, trust iFJF for parts that last season after season. Pool and spa equipment faces unique challenges — constant water pressure, chemical corrosion, UV exposure, and seasonal temperature swings. Inferior replacement parts can fail within a single season, leading to leaks, equipment damage, and costly emergency repairs. Our parts are manufactured to commercial-grade standards using UV-stabilized, chemical-resistant thermoplastics and corrosion-proof hardware for reliable performance year after year. Key Features & Benefits Chemical-Resistant Construction: Materials specifically engineered for chlorine, bromine, salt, and pH chemical resistance — will not crack, warp, or deteriorate like generic plumbing parts. UV-Stabilized Formula: Outdoor-rated materials resist sun damage, fading, and embrittlement from extended sunlight exposure in pool equipment installations. Precision Fit: Machined to exact OEM dimensions for leak-free connections and smooth operation — no forcing, modifications, or improvisation needed. Easy DIY Installation: Direct replacement requires only basic hand tools. Most installations take 15-30 minutes, saving you hundreds in service call fees. Quality Guaranteed: Every part undergoes dimensional verification and pressure testing before shipping. Backed by iFJF 1-year warranty and 30-day returns. Technical Specifications Specification Detail Material Heavy-Duty PVC / ABS / Glass-Filled Nylon Connection Type Threaded NPT / Slip Socket (model dependent) Pressure Rating Up to 50 PSI Working / 150 PSI Burst Chemical Compatibility Chlorine, Bromine, Salt, Muriatic Acid, Standard Pool Chemicals Temperature Range 32°F to 140°F Operating Frequently Asked Questions Q: Will this fit my specific pool equipment model?A: Please verify the dimensions, connection type, and thread size against your existing equipment. Most pool plumbing follows standard NPT or slip fitting dimensions. Message us your equipment model number for a definitive fitment check. Q: Is this part chlorine and chemical resistant?A: Yes, the materials are specifically selected for long-term exposure to pool and spa chemicals including chlorine, bromine, salt, and standard pH adjusters. Properly maintained, this part provides years of reliable service. Q: Can I install this myself or do I need a professional?A: Most pool equipment replacement parts are DIY-friendly with basic hand tools. Shut off the pump, relieve system pressure, swap the part, and test for leaks. Typical installation takes 15-30 minutes. Q: Is this an OEM or aftermarket part?A: This is a premium aftermarket replacement manufactured to match or exceed OEM specifications in quality and fit — at significant savings versus pool supply store pricing. Q: What is your return and warranty policy?A: 30-day hassle-free returns and 1-year warranty. If you receive an incorrect or defective part, we ship a replacement or issue a full refund — no restocking fees, ever. Explore More from iFJF Looking for related parts and accessories? Browse our complete selection of diesel filters, RV parts, pool equipment, and automotive components — all backed by fast US shipping and our satisfaction guarantee.

    $37.99

  • iFJF RP46074 Cartridge For 1300 1400 Tub/Shower Valve Single Lever New

    iFJF iFJF RP46074 Cartridge For 1300 1400 Tub/Shower Valve Single Lever New

    Product Overview The iFJF Valve is a premium aftermarket replacement part engineered for precision fit and lasting durability. Designed to match or exceed OEM specifications, this valve delivers reliable performance for your vehicle. Replaces OEM Part Numbers: RP46074 Brand: iFJF Condition: Brand New, Aftermarket Compatibility & Fitment Vehicle Make Model Year Range Engine This product fits multiple applications. Please verify fitment with your vehicle specifications. Technical Specifications Specification Detail Part Type Valve Brand iFJF Replaces OEM RP46074 Condition New Aftermarket Material High-Grade Steel / Aluminum / Composite Finish Corrosion-Resistant Coating Fitment Type Direct Replacement Key Features & Benefits Precision Engineering: Manufactured to exact tolerances for seamless fit and function OEM-Equivalent Performance: Meets or exceeds factory specifications for reliable operation Durable Construction: Built with high-quality materials to withstand demanding conditions Easy Installation: Direct bolt-on replacement — no modifications required Corrosion Resistant: Protective coating prevents rust and extends service life Cost-Effective: Premium quality at a fraction of OEM dealer pricing Thoroughly Tested: Each unit undergoes quality inspection before shipment Installation Guide Verify this valve matches your vehicle make, model, and year Gather necessary tools: socket set, wrenches, torque wrench, safety equipment Park vehicle on level surface and engage parking brake Remove the old/damaged component carefully, noting orientation Clean mounting surface and inspect surrounding components for wear Install the new iFJF Valve in the same orientation Torque all fasteners to manufacturer specifications Test operation before returning vehicle to service ⚠️ Professional installation recommended for safety-critical components. Always consult your vehicle service manual for torque specs. Frequently Asked Questions Q: Is this valve compatible with my vehicle? A: Please verify your vehicle's make, model, year, and engine against our compatibility table above. For specific fitment questions, contact us with your VIN number. Q: Does this replace OEM part numbers RP46074? A: Yes, this valve is designed as a direct replacement for RP46074. It meets or exceeds factory specifications. Q: What's included in the package? A: Each package includes the Valve assembly as shown. Installation hardware is included where applicable. Please check product images for complete contents. Q: Do you offer a warranty? A: Yes! All iFJF products come with a satisfaction guarantee. If you experience any issues, contact our customer service team for a replacement or refund. Q: How long does shipping take? A: Orders are processed within 1-2 business days. Standard shipping to the contiguous US takes 3-7 business days. Expedited options available at checkout. Related Products Looking for more? Check out these related products from iFJF: iFJF RP50587 Single Handle Cartridge Valve Replacement For Cartridge A Helpful Articles iFJF Blog — Installation Tips, Maintenance Guides & Product Updates How to Choose the Right Aftermarket Parts for Your Vehicle

    $37.99

  • iFJF 6" Vise Jaws Pads Protector for Any Metal Bench Vise with Magnetic Soft Vise Jaw Covers (Black)

    iFJF iFJF 6" Vise Jaws Pads Protector for Any Metal Bench Vise with Magnetic Soft Vise Jaw Covers (Black)

    Product OverviewThe 6 vise jaw pads provide professional-grade protection for your workpieces and bench vise. Featuring powerful integrated magnets, these pads snap securely onto any metal vise jaw and stay in place during use. The soft, non-marring surface prevents scratching, denting, and damaging delicate materials including wood, aluminum, brass, and finished surfaces.Perfect for gunsmiths, machinists, woodworkers, and DIY enthusiasts who demand precision workholding without workpiece damage. The durable composite material withstands repeated use while maintaining its protective properties.Key Features Built-In Magnets: Strong magnetic backing holds pads securely on any metal vise jaw Non-Marring Surface: Soft composite material protects workpieces from scratches and dents Universal Fit: Designed to fit most standard bench vise jaw sizes Quick Installation: Magnetic design allows instant attachment and removal Multi-Purpose: Ideal for woodworking, gunsmithing, metalworking, and general repair Compatibility & FitmentCompatible with most standard metal bench vises with jaw widths from 6". The magnetic backing adheres securely to ferrous metal vise jaws. Not suitable for aluminum or plastic vise jaws.Technical Specifications Specification Value Part Number 6 Jaw Width 6" Material Composite with Magnetic Backing Surface Type Non-Marring Soft Grip Attachment Integrated Magnets Application Universal Metal Bench Vises Why Choose iFJF Direct? Quality Assurance: Every iFJF product is manufactured to meet or exceed OEM specifications Fast USA Shipping: Orders ship from our US warehouse within 1-2 business days Best Price Guarantee: Premium quality at competitive prices with no dealer markup Expert Support: Our team of automotive and marine specialists is ready to help with fitment questions Hassle-Free Returns: 30-day return policy if the part doesn't fit your application Installation Tips1. Verify fitment by comparing your old part with product images. 2. Gather necessary tools before starting installation. 3. Clean all mounting surfaces thoroughly. 4. Follow factory service manual torque specifications where applicable. 5. Test operation after installation to confirm proper function.Frequently Asked QuestionsQ: Will these pads fit my vise?A: These magnetic vise jaw pads are designed to fit most standard metal bench vises. The magnets will adhere to any ferrous metal jaw surface.Q: How strong are the magnets?A: The integrated magnets provide secure attachment during normal use. For heavy impact work (hammering, pressing), we recommend confirming the pads are fully seated before beginning.Q: Can these be used on non-metal vises?A: The magnetic attachment requires ferrous metal vise jaws. For aluminum or composite vises, the pads can still be used but will need to be held in place manually.

    $25.99

  • 2-Pack 1.25" Accessory Hose for Intex Above Ground Pool Pump Replaceme — main product view

    iFJF 2-Pack 1.25" Accessory Hose for Intex Above Ground Pool Pump

    2-Pack 1.25" Accessory Hose for Intex Above Ground Pool Pump — Pool Equipment Replacement Built to Last Keep your pool or spa running efficiently with this precision-engineered replacement component from iFJF. Manufactured from chemical-resistant materials specifically selected for long-term exposure to chlorine, bromine, and salt water environments, this part delivers the same fit and function as the original manufacturer component at a fraction of the cost. Whether repairing a leaking valve, upgrading worn-out fittings, or performing seasonal maintenance, trust iFJF for parts that last season after season. Pool and spa equipment faces unique challenges — constant water pressure, chemical corrosion, UV exposure, and seasonal temperature swings. Inferior replacement parts can fail within a single season, leading to leaks, equipment damage, and costly emergency repairs. Our parts are manufactured to commercial-grade standards using UV-stabilized, chemical-resistant thermoplastics and corrosion-proof hardware for reliable performance year after year. Key Features & Benefits Chemical-Resistant Construction: Materials specifically engineered for chlorine, bromine, salt, and pH chemical resistance — will not crack, warp, or deteriorate like generic plumbing parts. UV-Stabilized Formula: Outdoor-rated materials resist sun damage, fading, and embrittlement from extended sunlight exposure in pool equipment installations. Precision Fit: Machined to exact OEM dimensions for leak-free connections and smooth operation — no forcing, modifications, or improvisation needed. Easy DIY Installation: Direct replacement requires only basic hand tools. Most installations take 15-30 minutes, saving you hundreds in service call fees. Quality Guaranteed: Every part undergoes dimensional verification and pressure testing before shipping. Backed by iFJF 1-year warranty and 30-day returns. Technical Specifications Specification Detail Material Heavy-Duty PVC / ABS / Glass-Filled Nylon Connection Type Threaded NPT / Slip Socket (model dependent) Pressure Rating Up to 50 PSI Working / 150 PSI Burst Chemical Compatibility Chlorine, Bromine, Salt, Muriatic Acid, Standard Pool Chemicals Temperature Range 32°F to 140°F Operating Frequently Asked Questions Q: Will this fit my specific pool equipment model?A: Please verify the dimensions, connection type, and thread size against your existing equipment. Most pool plumbing follows standard NPT or slip fitting dimensions. Message us your equipment model number for a definitive fitment check. Q: Is this part chlorine and chemical resistant?A: Yes, the materials are specifically selected for long-term exposure to pool and spa chemicals including chlorine, bromine, salt, and standard pH adjusters. Properly maintained, this part provides years of reliable service. Q: Can I install this myself or do I need a professional?A: Most pool equipment replacement parts are DIY-friendly with basic hand tools. Shut off the pump, relieve system pressure, swap the part, and test for leaks. Typical installation takes 15-30 minutes. Q: Is this an OEM or aftermarket part?A: This is a premium aftermarket replacement manufactured to match or exceed OEM specifications in quality and fit — at significant savings versus pool supply store pricing. Q: What is your return and warranty policy?A: 30-day hassle-free returns and 1-year warranty. If you receive an incorrect or defective part, we ship a replacement or issue a full refund — no restocking fees, ever. Explore More from iFJF Looking for related parts and accessories? Browse our complete selection of diesel filters, RV parts, pool equipment, and automotive components — all backed by fast US shipping and our satisfaction guarantee.

    $59.99

  • Intex Pool Hose Adapter A — Threaded Collar for 1500-4000 GPH Pumps | iFJF

    iFJF Intex Pool Hose Adapter A — Threaded Collar for 1500-4000 GPH Pumps | iFJF

    Product Overview The Intex Pool Hose Adapter A — Threaded Collar for 1500-4000 GPH Pumps | iFJF from iFJF Direct is engineered to meet or exceed OEM specifications for vehicles. This pool hose adapter delivers reliable performance at factory-direct pricing. Key Features Premium Quality: Manufactured to strict quality control standards with durable materials for long service life Direct Fit: Designed as a direct replacement — no modifications required for installation on compatible vehicles Factory Direct Value: Eliminate the middleman markup — get OEM-quality parts at aftermarket prices Fast US Shipping: Ships from our US warehouse within 1 business day of order Compatibility This product is designed to fit vehicles. Please verify compatibility with your specific vehicle using our fitment guide or contact our support team before ordering. Why Choose iFJF Direct? Quality Assurance: Every product undergoes multi-point inspection before shipping US-Based Support: Our customer service team is available to answer your fitment and installation questions Hassle-Free Returns: 30-day return policy on unused parts in original packaging Expert Community: Join thousands of DIY mechanics and professional technicians who trust iFJF Frequently Asked Questions Q: Will this fit my Intex 2500 GPH filter pump?A: Yes. This adapter fits all Intex filter pumps rated 1500, 2000, 2500, and 4000 GPH that use threaded hose connections. It's also compatible with Intex saltwater chlorine generators and sand filter pump conversions. Q: How do I connect a 1.25" hose to the 1.5" pump port?A: This adapter is designed for exactly that conversion. Attach the smaller threaded end to your 1.25" hose using the included stainless steel clamp, then thread the larger end onto the pump's 1.5" plunger valve or filter connection. The O-rings ensure a watertight seal. Q: What's included in the package?A: Each package includes: 2× threaded hose adapters (Type A collars), 2× stainless steel hose clamps, and 4× rubber O-rings — everything needed for a complete pump-to-hose connection on both intake and return sides. Q: Is this compatible with the Intex sand filter pump?A: Yes. If you're upgrading from a standard cartridge filter to an Intex sand filter pump, these adapters handle the hose size transition. The threaded collar design matches both standard and sand filter pump ports. Q: Will the plastic adapters crack under pressure?A: The adapters are made from high-grade, glass-reinforced ABS plastic designed to withstand typical above-ground pool pump pressures (up to 50 PSI operating pressure). They will not crack or deform under normal use. 🔗 Related Products

    $47.99

  • Backflow Preventer Repair Kit 3/4-1 inch Poppet Spring Seat for 975XL 975XL2 Complete

    iFJF Backflow Preventer Repair Kit — 3/4"-1" Poppet Spring Seat for 975XL 975XL2 | iFJF

    Bi-Directional Backflow Preventer Repair Kit for 3/4" — 1" 975XL & 975XL2 The iFJF Backflow Preventer Repair Kit includes everything needed to rebuild the check valve assembly on 3/4-inch and 1-inch bi-directional backflow preventers — specifically the 975XL and 975XL2 series. When your backflow preventer fails its annual certification test or develops a persistent leak, replace the worn internal components instead of the entire assembly at 5x the cost. Compatible Backflow Preventer Models Model Series Size 975XL 3/4 inch & 1 inch 975XL2 3/4 inch & 1 inch Generic RBPA Similar bi-directional reduced pressure zone assemblies (verify fit) Kit Contents 3 Check Springs — Replace worn or corroded springs that cause the check valve to fail closed 2 Lift Valves (Poppets) — New poppet assemblies restore proper check valve seating and seal 5 O-Rings — Complete set of sealing O-rings for all internal connections 1 Safety Valve — Replacement relief valve for the intermediate zone 1 Safety Valve Seat — Mating seat for the safety/relief valve 1 PTFE Thread Seal Tape Roll — For leak-free reassembly 1 Instruction Manual — Step-by-step rebuild guide with diagrams Key Features Complete Rebuild Kit — Every wear component is included — no need to order individual parts or scavenge from old assemblies OEM-Spec Materials — Springs, poppets, and O-rings match original 975XL/975XL2 specifications for reliable sealing and pressure regulation DIY Savings — Rebuilding with this $47.99 kit avoids a $300-$600 backflow preventer replacement, plus the cost of a licensed plumber Pass Your Annual Test — Worn internal seals are the #1 cause of failed backflow certification tests; this kit addresses all common wear points No Special Tools — Basic wrenches and screwdrivers are all you need; the included instruction manual walks you through the process FAQ Q: Will this fit my specific backflow preventer?A: This kit is designed for 3/4-inch and 1-inch 975XL and 975XL2 bi-directional backflow preventers. Verify your model number — it's stamped on the brass body of the assembly. Q: Do I need a plumber to install this?A: Many DIY homeowners complete this repair themselves. However, check local regulations — some jurisdictions require a licensed backflow technician to service and re-certify backflow preventers after internal repairs. Q: What symptoms indicate I need this repair kit?A: Failed annual certification test, water leaking from the relief valve port, low system pressure, or visible corrosion/deterioration on the check valve components during inspection. Q: Can I use this on a 2 inch backflow preventer?A: No — this kit is specifically sized for 3/4-inch and 1-inch assemblies. 2-inch backflow preventers use larger internal components that are not compatible with this kit. Q: Does this kit include the test cocks?A: No — the test cocks (small ball valves used for testing) are external to the check valve assembly and are not included in this kit. This kit focuses on the internal check valve and relief valve wear components.

    $47.99

  • GP500520 Pressure Balancing Cartridge for Kohler Rite-Temp Shower Valve — Replac - View 1

    iFJF GP500520 Pressure Balancing Cartridge for Kohler Rite-Temp Shower Valve — Replacement

    GP500520 Pressure Balancing Cartridge — Kohler Rite-Temp Replacement The iFJF GP500520 cartridge is a precision-engineered replacement for Kohler Rite-Temp pressure balancing shower valves. When your shower temperature swings wildly between hot and cold — especially when someone flushes a toilet or runs the washing machine — the pressure balancing cartridge is almost always the culprit. This direct-fit replacement restores stable, comfortable shower temperature control. Key Features Pressure Balancing Technology: Maintains consistent water temperature even when water pressure fluctuates Direct Replacement: Drop-in fit for Kohler Rite-Temp valves — no modifications needed Premium Materials: High-grade plastic body with brass stem and ceramic disc internals Smooth Operation: Precision-engineered spool valve eliminates sticking and stiff handle operation Anti-Scald Protection: Automatically adjusts mix ratio to prevent sudden hot water surges DIY-Friendly: Installs in 15–20 minutes with basic tools Compatibility Brand Valve System Part Numbers Kohler Rite-Temp GP500520 Kohler Rite-Temp GP76851 Kohler Rite-Temp K-304 All variants Kohler Rite-Temp K-8300 Series K-8304, K-8305, K-8306 Specifications Specification Value Part Number GP500520 Valve Type Pressure Balancing Stem Material Brass Body Material High-grade engineered plastic Connection Size 1/2" Application Single-handle shower valve Symptoms of a Bad Cartridge Shower temperature suddenly goes hot or cold without adjusting the handle Water temperature changes when other fixtures are used (toilet flush, dishwasher, etc.) Handle is stiff or difficult to turn Water continues to drip from the shower head when the valve is off Uneven hot/cold mix — can't find a comfortable temperature Installation Overview Turn off water supply to the shower valve (main shut-off or integral stops) Remove the handle, trim plate, and any retaining clips Pull out the old cartridge using pliers or a cartridge puller tool Clean the valve body interior, removing any debris or mineral buildup Insert the new GP500520 cartridge, ensuring proper alignment Reinstall the retaining clip, trim plate, and handle Turn water back on and test for leaks and smooth operation Pro Tip: Apply a thin layer of silicone plumber's grease to the O-rings before installation for easier future removal. Frequently Asked Questions Q: How do I know if I have a Rite-Temp valve? A: Kohler Rite-Temp valves have a single handle and are labeled "Rite-Temp" on the trim plate. They were installed in millions of homes from the 1990s to present. Remove the handle and trim — the cartridge shape will match the GP500520. Q: Is this an OEM Kohler part? A: This is a high-quality aftermarket replacement manufactured to meet or exceed OEM GP500520 specifications at a fraction of the dealer price. Q: What's the difference between GP500520 and GP76851? A: The GP500520 is the cartridge only. The GP76851 includes both the cartridge and the mixer cap. If your cap is also worn or leaking, consider the combo kit for a complete rebuild. Q: Can I install this myself or do I need a plumber? A: Most DIYers with basic home repair experience can replace this cartridge in 15–20 minutes. No specialty tools required beyond a screwdriver and adjustable wrench. Q: My water is very hard — will this cartridge last? A: Hard water can shorten cartridge life. We recommend installing a whole-house water softener or regularly cleaning the cartridge every 12–18 months in hard water areas. Related Products & Resources Shop More Plumbing Parts Browse our full selection at unbeatable prices. View All Plumbing Parts → Helpful Articles Installation Guides & How-Tos Maintenance Tips & Troubleshooting Buying Guide: Choosing the Right Parts

    $29.99

  • 472610Z Switch Membrane Pad Replacement for Pool and Spa Heater Electrical System — 472610Z — Front View

    iFJF 472610Z Switch Membrane Pad Replacement for Pool and Spa Heater

    Product Overview The 472610Z Switch Membrane Pad Replacement for Pool and Spa Heater Electrical System is a premium aftermarket replacement part engineered to meet or exceed OEM specifications. this component delivers reliable performance and durability. Manufactured with high-grade materials and precision engineering, it ensures a perfect fit and long service life. Key Features & Benefits Quality Construction: Premium-grade materials for maximum durability and corrosion resistance Quality Construction: Precision-engineered to OEM specifications for exact fitment Quality Construction: Rigorous quality control testing ensures reliable performance Quality Construction: Easy installation with basic hand tools — no modifications required Compatibility & Fitment Application Details Replaces Part Numbers 472610Z Technical Specifications Specification Value Part Type Aftermarket Replacement Material High-Grade Steel / Aluminum / Composite Finish Corrosion-Resistant Coating Installation Direct Bolt-On Replacement Warranty 1-Year Limited Warranty Why Choose iFJF? iFJF is a trusted name in aftermarket automotive and powersports parts. Every product undergoes strict quality control to ensure it meets rigorous performance standards. We stand behind our products with responsive customer support and a satisfaction guarantee. Our parts are trusted by professional mechanics and DIY enthusiasts alike for their reliability, fit, and value. Installation Tips Always disconnect the battery before beginning any installation Compare the new part with the old one to verify fitment before installation Use appropriate tools and follow manufacturer torque specifications Clean mounting surfaces thoroughly before installing the new component Test operation after installation to ensure proper function Package Includes 1x 472610Z Switch Membrane Pad Replacement for Pool and Spa Heater Electrical System Mounting hardware (if applicable) Installation instructions Frequently Asked Questions Q: Will this fit my vehicle?A: Yes, this is a direct-fit replacement part. Please check the compatibility table above and verify your vehicle's part number or model year to confirm fitment. Q: Is professional installation required?A: No, this part is designed for DIY installation with basic hand tools. However, if you are not comfortable with mechanical work, we recommend having it installed by a certified technician. Q: How does this compare to OEM?A: This aftermarket replacement is manufactured to meet or exceed OEM specifications. It offers the same fit, function, and reliability as the original part at a significantly lower cost. Q: What materials are used?A: Our parts are manufactured using high-grade materials including carbon steel, aluminum alloys, and composite materials selected for durability, heat resistance, and corrosion protection. Q: What warranty is included?A: All iFJF products come with a 1-year limited warranty against manufacturing defects. If you experience any issues, contact our customer support team for a replacement or refund. Q: How fast is shipping?A: Orders are processed within 1-2 business days. Standard shipping takes 3-7 business days within the continental US. Expedited shipping options are available at checkout. Related Products & Resources You May Also Need Browse All Products Helpful Resources Installation Guides & How-To Articles

    $33.99

  • 90 Degree Mini Positioning Square Wood Working Tool Small Pocket Check Square on Carpenter Cutting Tools, Premium Precision Woodworking Tools — iFJF Direct Product Image

    iFJF iFJF 90 Degree Mini Positioning Square Wood Working Tool Small Pocket Check Square on Carpenter Cutting Tools, Premium Precision Woodworking Tools

    Product Overview The 90 Degree Mini Positioning Square Wood Working Tool Small Pocket Check Square on Carpenter Cutting Tools, Premium Precision Woodworking Tools is a premium-quality replacement part engineered to meet or exceed OEM specifications. Designed for durability, reliability, and perfect fitment, this iFJF product delivers professional-grade performance at an affordable price. Key Features Precision Accuracy: Machined for perfect 90-degree angles in woodworking layouts. Compact Mini Design: Pocket-sized for easy portability on any job site. Durable Construction: Quality materials resist wear and maintain accuracy. Versatile Use: Ideal for carpentry, cabinet making, framing, and general layout. Clear Markings: Easy-to-read graduations for quick measurements. Compatibility & Fitment Designed as a direct replacement for the following applications. ⚠️ Always verify your equipment model, year, and specifications before ordering. Make Model Year Notes Universal Various — See product title for fitment Technical Specifications Specification Detail Brand iFJF Condition New Fitment Type Direct Replacement Part Number 90 Type Mini Square Angle 90° ⚠️ Important — Off-Road Use Only This product is intended for OFF-ROAD and COMPETITION USE ONLY. Not certified for highway use. Installation may affect emissions compliance. Check local regulations. iFJF assumes no liability for improper use. Why Choose iFJF? OEM-Grade Quality: Manufactured to strict tolerance standards for reliable performance Rigorous Testing: Every product undergoes quality inspection before shipping Fast Shipping: Orders processed within 1-2 business days from our US warehouses Expert Support: Technical assistance available for installation and troubleshooting Hassle-Free Returns: 30-day return policy for your peace of mind Frequently Asked Questions Q: How accurate is this square?A: Machined to precise 90-degree tolerance for professional woodworking accuracy. Q: What size is this mini square?A: Compact pocket-sized design — see product images and listing details for exact dimensions. Q: What is it made from?A: Constructed from durable materials designed to maintain accuracy through regular use. Q: Can this be used for metalworking?A: Primarily designed for woodworking and carpentry. Suitable for general layout work on various materials. Q: Does it come with a case?A: See product images for exact package contents. Contact us for detailed specifications.

    $27.99

  • 2Pcs 15 Stage Shower Replace Filter Cartridge Remove Chlorin | — Main Product View

    iFJF 2Pcs 15 Stage Shower Replace Filter Cartridge Remove Chlorin | iFJF

    Upgrade Your Shower Water Quality with iFJF 15-Stage Filtration Hard water, chlorine, and dissolved impurities in your shower water do more than just dry out your skin and hair—they can aggravate eczema, cause scalp irritation, and leave mineral deposits that clog showerheads. The iFJF 15-Stage Shower Filter Replacement Cartridge delivers comprehensive multi-layer filtration that transforms your daily shower into a spa-like experience with noticeably softer, cleaner water. Inside each cartridge, 15 stages of high-efficiency filter media work together: PP cotton, activated carbon, calcium sulfite, VC balls, alkali balls, medical stone, and other advanced materials that effectively remove chlorine, fluorine, heavy metals, and other harmful substances—while balancing pH for water that feels gentler on skin and hair. Key Features 15-Level High-Efficiency Filter Element: Combines PP cotton, activated carbon, calcium sulfite, VC ball, alkali ball, medical stone, and other premium filter materials in a multi-layer configuration. Each stage targets a specific contaminant for comprehensive water purification. Chlorine & Chemical Removal: Activated carbon and calcium sulfite media effectively remove chlorine, chloramines, and other chemical disinfectants that cause dry, itchy skin and strip natural oils from hair. Heavy Metal Filtration: Advanced media captures heavy metals, sediment, rust, and other particulate matter that can accumulate in municipal and well water supplies. pH Balancing & Skin Care: Alkali balls and medical stone help balance water pH, while VC balls infuse the water with skin-nourishing properties that reduce dryness, itching, and promote healthier hair. Designed for Your Health: High-efficiency filtration and built-in VC balls improve water quality, reduce skin dryness and itching, promote healthy hair, and provide special care for children—making every bath a healthier, more enjoyable experience. Versatile Multi-Scenario Use: Suitable for overhead, handheld, showerhead, and combination shower heads in bathrooms and kitchens. Also ideal for RV installation when traveling—reducing plastic bottled water use and environmental waste. Easy Tool-Free Installation: Simply fix the filter onto the faucet or shower arm in the correct direction and ensure no water leakage. Turn on the faucet and rinse the filter for about 3 minutes before first use to activate the media. 2-Pack Value: Each package includes two 15-stage shower water purifier filter elements, covering 6-12 months of filtration depending on usage frequency and water quality. 15-Stage Filtration Breakdown Stage Filter Media Function 1-2 PP Cotton (Micro-Fiber) Removes sediment, rust, sand, and large particles 3-4 Activated Carbon Absorbs chlorine, odors, and organic chemicals 5-6 Calcium Sulfite Targeted chlorine and chloramine removal 7-8 KDF / Redox Media Heavy metal removal (lead, mercury, iron) 9-10 Alkali Ceramic Balls pH balancing and water softening 11-12 Medical Stone Mineralization and trace element release 13-14 VC Balls Vitamin C infusion for skin & hair nourishment 15 Micro-Fiber Mesh Final polishing and fine particle capture Technical Specifications Specification Detail Product Type 15-Stage Shower Filter Replacement Cartridge Filter Stages 15 Layers of Multi-Media Filtration Filter Media PP Cotton, Activated Carbon, Calcium Sulfite, KDF, Alkali Balls, Medical Stone, VC Balls Removes Chlorine, Heavy Metals, Sediment, Fluorine, Rust, Odors Benefits pH Balancing, Water Softening, Skin & Hair Nourishment Package Quantity 2 Filter Cartridges Compatible With Overhead, Handheld, Showerhead, Combo Shower Heads, RV Brand iFJF Installation & First Use Prepare: Remove the old filter cartridge from your shower filter housing. Clean the housing interior if needed. Insert: Place the new iFJF 15-stage cartridge into the filter housing, ensuring it aligns correctly according to the directional markings. Secure: Tighten the housing cap securely by hand—do not overtighten or use tools, as this may damage the threads or gasket. Flush: Turn on the shower and let water run through the filter for approximately 3 minutes before first use. This activates the filter media and flushes out any carbon dust. Check: Verify there are no leaks at the housing connection points. Hand-tighten further if needed. Maintenance & Replacement Suggestion: Regularly check the working status of the filter and replace the filter element according to the frequency of use to maintain the best filtering effect. General replacement guidelines: Household of 1-2: Replace every 6 months Household of 3-4: Replace every 4-5 months Hard water areas: Replace every 3-4 months regardless of household size Signs it's time: Reduced water pressure, return of chlorine smell, or visible discoloration of the filter media Suitable for Multiple Scenarios Home Bathroom: Overhead rain showers, handheld showerheads, and combination shower systems Kitchen: Sink-mounted faucets where filtered water is desired RV & Travel: Install on RV showers to filter campground water, reducing reliance on bottled water and minimizing plastic waste Children's Bath: The VC ball-infused filtration provides extra-gentle water for babies and children with sensitive skin Frequently Asked Questions How do I know when to replace the filter cartridge? Replace the cartridge when you notice decreased water pressure, a return of chlorine smell in your shower water, visible darkening or discoloration of the filter media, or when the recommended time period (3-6 months depending on usage and water hardness) has elapsed. Will this filter cartridge fit my existing shower filter housing? This 15-stage cartridge is designed as a universal replacement for most standard shower filter housings. It fits inline filter housings used with overhead, handheld, and combination showerheads. Please measure your existing cartridge dimensions and compare before ordering. Does this filter reduce water pressure significantly? When the cartridge is fresh, the 15-stage media design allows excellent water flow with minimal pressure drop. As the filter captures contaminants over its lifespan, you may notice a gradual decrease in pressure—this is a normal indicator that replacement time is approaching. Is this filter effective for hard water issues like limescale? Yes. The alkali balls and medical stone stages help soften hard water by balancing pH and reducing mineral scale. While not a full water softener, it significantly reduces the effects of hard water on skin and hair and helps prevent scale buildup on showerheads. Can I use these cartridges in an RV? Absolutely. The multi-scenario design makes these cartridges ideal for RV use, where water quality varies significantly between campgrounds. Installing one reduces the need for plastic bottled water, making your travels more environmentally friendly while ensuring healthier shower water for you and your family. Product Overview 2Pcs 15 Stage Shower Replace Filter Cartridge Remove Chlorin | is a premium-quality replacement component engineered for exact fitment and reliable performance. Manufactured to meet or exceed OEM specifications using high-grade materials, this part delivers dependable service life for your equipment. Compatibility This part is designed as a direct replacement for the OEM part numbers referenced in this listing. Please verify your equipment model number before ordering. If you are unsure about compatibility, contact our support team with your equipment details for verification. Why Choose iFJF Direct iFJF Direct specializes in premium replacement parts for diesel trucks, RVs, marine, pool & spa, and automotive applications. Every product is backed by our commitment to quality, fast US-based shipping, and responsive customer support. We source directly from IATF 16949-certified manufacturers to bring you OEM-equivalent quality at competitive prices.

    $37.99

  • 10747 25010 Plunger Valve Assembly w/ O-Rings for Above Grou — Front View

    iFJF 10747 25010 Plunger Valve Assembly w/ O-Rings for Above Ground | iFJF

    10747 / 25010 Plunger Valve Assembly for Above Ground Pool Systems The iFJF Plunger Valve Assembly is a direct replacement for Intex part numbers 10747, 25010, and 25080RP. This essential pool plumbing component controls water flow between your above ground pool and the filtration system, with a simple push-pull plunger mechanism that anyone can operate. Key Features Complete Assembly: Includes valve body, plunger stem with handle, and O-ring seals — ready to install Cross-References: Direct replacement for Intex 10747, 25010, 25080RP Push-Pull Operation: Simple plunger mechanism — push to close, pull to open 1.25-Inch Hose Connection: Standard size for most above ground pool filter pumps O-Rings Included: Pre-installed O-rings for watertight sealing — no additional parts needed Compatibility Intex above ground pool filter pumps using plunger valve connections Intex sand filter pump systems (SF series) Most Bestway and Coleman above ground pool filtration systems Fits 1.25-inch diameter pool hoses Replacement Instructions Turn off and unplug the pool pump Push the old plunger valve(s) to the closed position Loosen the hose clamps and disconnect the hoses Unscrew the old valve assembly from the pool/pump fitting Clean the threads on the fitting Ensure the new O-rings are properly seated on the new valve Screw the new valve onto the fitting — hand-tighten plus 1/4 turn Reattach hoses and tighten clamps Open the valve (pull up) and restart the pump FAQ Q: What's included in this valve assembly?A: The assembly includes the plunger valve body, plunger stem with handle, O-rings for watertight seal, and hose connection fittings for standard 1.25-inch pool hoses. Q: Is this compatible with Intex sand filter pumps?A: Yes. This plunger valve assembly is compatible with Intex sand filter pump models that use standard plunger valve connections. Q: How do I replace a leaking plunger valve?A: 1) Turn off the pump. 2) Close the plunger valves. 3) Unscrew the hose clamps. 4) Remove the old valve. 5) Install the new valve with O-rings properly seated. 6) Reattach hoses and tighten clamps. 7) Open valves and restart the pump. Q: Why is my valve leaking even with a new O-ring?A: Check for cracks in the valve body, worn plunger stem, or debris on the sealing surface. If the valve body is cracked, replacement is the only fix. Also ensure the O-ring is properly lubricated with silicone grease.Related Products Smart WiFi Sprinkler Controller 8-Zone — Weather Intelligent | iFJF 1.25" & 1.5" Pool Pipe Support with Plunger Valve – Above Ground Pool Fittings ( 1.25" Pool Inlet Jet Nozzle Hose Holder & Strainer Grid for Above Ground Pools | 10-Pack Brass Pool Cover Anchor Collar Beauty Rings - Universal 9/16" ID | iFJF 11872 Dual Split Hose Plunger Valve Connector for Above Ground Pool Pump | iFJF 📚 Related Guides & Articles iFJF Product Buying Guide — How to Choose the Right Part Diesel vs. Gas Engines: Complete Maintenance Guide

    $55.99

  • iFJF Pool Heater Membrane Compatible With MasterTemp Pool And Spa Heater Electrical System Replacement Pentair 472610Z And Sta-Rite 42002-0029Z

    iFJF iFJF Pool Heater Membrane Compatible With MasterTemp Pool And Spa Heater Electrical System Replacement Pentair 472610Z And Sta-Rite 42002-0029Z

    Product Overview Pool Heater Membrane Compatible With MasterTemp Pool And Spa Heater Electrical System Replacement Pentair 472610Z And Sta-Rite 42002-0029Z — a high-quality aftermarket replacement part engineered to meet or exceed OEM specifications. Designed for durability and precision fit, this product delivers reliable performance for your vehicle or equipment. Key Features Precision Engineering — Manufactured to exact tolerances for a direct fit and reliable operation. Heavy-Duty Construction — Built with premium materials to withstand demanding conditions and extended service life. Easy Installation — Designed for straightforward bolt-on replacement with basic hand tools. No special equipment required. Cost-Effective Alternative — Provides OEM-comparable quality at a fraction of dealership pricing. Quality Tested — Each unit undergoes rigorous quality control inspection before shipping. Compatibility Information Please verify fitment for your specific vehicle or equipment before ordering. Check your owner's manual or existing part number to confirm compatibility. Specifications Brand iFJF Condition New Material Premium-Grade Components Package Includes 1x Pool Heater Membrane Compatible With MasterTemp Pool And Spa Heater Electrical S Why Choose iFJF iFJF Direct specializes in high-quality aftermarket parts and accessories for automotive, powersports, marine, and outdoor applications. Every product is backed by our commitment to quality and customer satisfaction. ✅ Manufactured to strict quality standards ✅ Fast, reliable shipping from US warehouses ✅ Responsive customer support team ✅ 30-day return policy for your peace of mind Frequently Asked Questions Q: Will this fit my specific model? A: Please refer to the compatibility information above or contact our support team with your vehicle/equipment details. We're happy to verify fitment before you order. Q: Is this an OEM or aftermarket part? A: This is a premium aftermarket replacement part manufactured to meet or exceed OEM specifications. It provides exceptional quality at a more affordable price point. Q: What's included in the package? A: The package includes the Pool Heater Membrane Compatible With MasterTemp Po as shown in the listing images. Installation hardware is included where applicable. Q: How difficult is the installation? A: Installation is designed to be straightforward for anyone with basic mechanical skills. Most installations can be completed with standard hand tools. Q: What is your return policy? A: We offer a 30-day return policy. If the part doesn't fit or you're not satisfied, contact us for a return authorization. The item must be in new, unused condition. Q: How fast is shipping? A: Orders are processed within 1-2 business days. Standard shipping typically delivers within 3-7 business days within the continental US. Shop with Confidence Add to cart now and get your Pool Heater Membrane Compatible With MasterTemp Po shipped fast. Questions? Contact our support team — we respond within 24 hours.

    $37.99

  • GP51487 Tank Bolt Assembly Kit for Kohler Wellworth Triangle Toilet — Replacemen - View 1

    iFJF GP51487 Tank Bolt Assembly Kit for Kohler Wellworth Triangle Toilet — Replacement

    GP51487 Tank Bolt Assembly Kit — Kohler Wellworth Replacement The iFJF GP51487 tank bolt assembly kit provides everything you need to stop leaks and re-secure your Kohler toilet tank. Designed specifically for the Kohler Wellworth triangle-shaped tank-to-bowl connection, this kit replaces worn-out bolts, gaskets, and washers that cause water pooling around the base of your toilet tank. Key Features Complete Kit: Includes all bolts, gaskets, washers, and nuts for a full tank-to-bowl rebuild Triangle Gasket Design: Precision-molded rubber gasket matches the unique Kohler Wellworth tank shape Corrosion-Resistant Bolts: Solid brass bolts won't rust or seize like steel alternatives Leak-Proof Seal: High-quality rubber washers compress evenly for a watertight fit Direct OEM Replacement: Identical fit to Kohler GP51487 assembly 15-Minute Install: All parts included — no extra trips to the hardware store Compatibility Brand Model Tank Shape Kohler Wellworth Triangle Kohler Wellworth Lite Triangle ⚠️ Verify your tank-to-bowl connection is triangular before ordering. Standard round/oval gasket toilets require a different kit. What's Included Component Material Quantity Tank Bolts Brass 2 Flat Washers Stainless Steel 2 Rubber Washers EPDM Rubber 2 Hex Nuts Brass 2 Triangle Tank Gasket Rubber 1 Signs You Need a New Tank Bolt Kit Water pooling around the base of the toilet tank (not the floor — that's a wax ring issue) Visible rust or corrosion on existing tank bolts Tank wobbles or shifts when you sit on the toilet Constant condensation or dampness at the tank-to-bowl joint Bolts are seized and cannot be tightened further Installation Steps Shut off the water supply valve and flush to empty the tank Disconnect the water supply line from the fill valve Remove the old tank bolts — you may need penetrating oil if seized Lift the tank off the bowl and clean both mating surfaces thoroughly Remove the old gasket and any residue Place the new triangle gasket into the tank opening Insert new brass bolts through the tank holes with rubber washers underneath Carefully lower the tank onto the bowl, guiding the bolts through the bowl holes Install flat washers and nuts from below, hand-tighten evenly Use a wrench to snug both nuts equally — DO NOT overtighten (cracks porcelain!) Reconnect the water supply, turn on the valve, and check for leaks Frequently Asked Questions Q: How do I know if my toilet needs the triangle or round gasket? A: The Kohler Wellworth uses a distinct triangular tank-to-bowl seal. If you shine a flashlight between the tank and bowl and see a triangular shape, this kit is correct for your toilet. Q: Can I use this on non-Kohler toilets? A: This kit is specifically designed for the Kohler Wellworth's unique triangle connection. It will not properly seal round-gasket toilets from other brands. Q: How tight should I make the tank bolts? A: Hand-tighten plus 1/4 to 1/2 turn with a wrench. Overtightening is the #1 cause of cracked toilet tanks. Tighten both bolts evenly in small increments. Q: Do I need to replace the fill valve at the same time? A: Not required, but if your toilet is over 5 years old, replacing the fill valve and flapper while the tank is off is a smart preventive maintenance step. Related Products & Resources Shop More Plumbing Parts Browse our full selection at unbeatable prices. View All Plumbing Parts → Helpful Articles Installation Guides & How-Tos Maintenance Tips & Troubleshooting Buying Guide: Choosing the Right Parts Related Guide Read: Fix Your Kohler Rite-Temp Shower Valve

    $37.99

  • iFJF 2-Pack 1.25" Swimming Pool Pipe Holder Replacement for Intex Filter Pumps with 3 Clamps

    iFJF iFJF 2-Pack 1.25" Swimming Pool Pipe Holder Replacement for Intex Filter Pumps with 3 Clamps

    Out of stock

    Overview Stop pool hose stress cracks before they start with the iFJF 2-Pack 1.25 inch Swimming Pool Pipe Holders. These essential accessories provide structural support for suction and return hoses on Intex filtration pump systems eliminating tension and pulling that leads to cracked pool wall connections leaking liners and detached hoses. Each set includes two pipe holders and three clamps — everything needed to protect both sides of your pool plumbing. Compatibility Category Compatible Products Pool Type Intex Above-Ground Pools with 1.25 inch Hose Connections Filter Pumps Intex 1500 GPH 2500 GPH 4000 GPH Filtration Systems Hose Diameter 1.25 Inches (32mm) Standard Intex Hose Verify your hose diameter before ordering. Intex offers both 1.25 inch and 1.5 inch hose connections on different models. Key Features Complete 2-Pack Value: Includes 2 pipe holders — one for suction side and one for return side of filtration system 3 Secure Clamps: Tight-grip plastic clamps prevent hose slippage even under full pump pressure Optimized for 1.25 inch Hoses: Precision-fit for standard Intex 1.25 inch (32mm) pool hoses UV-Resistant Material: High-quality outdoor-grade plastic withstands sun exposure without becoming brittle Stress Relief Design: Reduces tension and pulling at pool wall inlet/outlet connections preventing cracks and liner leaks Tool-Free Installation: Simply mount connect and clamp — no special tools or plumbing expertise required Technical Specifications Specification Value Hose Diameter 1.25 Inches (32mm) Material High-Grade UV-Resistant Plastic Package Quantity 2 Pipe Holders + 3 Plastic Clamps Recommended Pumps Intex 1500 2500 4000 GPH Filter Pumps Installation Tool-Free — Under 15 Minutes Installation Drain Pool Below Connections: Lower water level below inlet and outlet ports or plug from inside Position Holder: Place pipe holder at pool wall interface where hose connects Connect Hose: Attach 1.25 inch Intex hose to pool wall fitting as normal Secure with Clamp: Position clamp over hose and pipe holder junction tighten until snug Repeat: Install second pipe holder on opposite connection suction/return Test: Refill to operating level start pump and check for leaks or hose movement Why Choose iFJF? Factory Direct Supply: iFJF manufactures its own pool replacement parts — no middleman markups Preventative Solution: Much cheaper than replacing cracked pool liner or leaking wall connection from unsupported hoses Bulk Orders Welcome: Need replacements for multiple pools? Contact support@ifjf.net for wholesale pricing Universal Intex Fit: Designed to work with all standard Intex above-ground pool hose connections FAQ Q: Will these work with 1.5 inch Intex hoses?A: No these are specifically designed for 1.25 inch (32mm) hoses. If your Intex system uses 1.5 inch hoses these will not fit properly. Q: How many pipe holders do I need for one pool?A: This 2-pack provides one holder for suction side and one for return side — sufficient for single Intex above-ground pool. Q: Do these work with non-Intex brand filter pumps?A: Designed for Intex hose connection standard. Compatibility with other brands depends on hose diameter and connection type. Q: Can I use for rigid PVC pipe instead of flexible hose?A: Designed for flexible Intex pool hoses. Not suitable for rigid PVC pipe installations. Q: Will the plastic crack in cold weather?A: UV-resistant plastic is formulated for outdoor temperature ranges. For winter store holders indoors for maximum longevity. Q: Is professional installation required?A: No designed for simple DIY installation. No plumbing experience or special tools needed.

    Out of stock

    $19.99

  • 1.25" & 1.5" Pool Pipe Support with Plunger Valve – Above Gr — Front View

    iFJF 1.25" & 1.5" Pool Pipe Support w/ Plunger Valve for Above Ground | iFJF

    1.25" & 1.5" Pool Pipe Support with Plunger Valve — 2-Pack The iFJF Pool Pipe Support Kit includes two dual-size pipe supports with integrated plunger valves, designed for above ground pool plumbing. Each support prevents hose kinking and sagging while providing easy flow control — compatible with both 1.25-inch and 1.5-inch pool hoses. Key Features Dual Size Compatibility: Each support accepts both 1.25-inch and 1.5-inch pool hoses — no need to know your exact size before ordering Integrated Plunger Valve: Push-to-close, pull-to-open mechanism for quick water shutoff during maintenance Prevents Hose Kinking: Keeps hoses at the optimal angle to prevent flow-restricting kinks that reduce pump efficiency Reduces Wall Fitting Stress: Supports the weight of water-filled hoses, taking strain off the pool wall connections 2-Pack Value: Covers both the inlet and outlet connections on a standard above ground pool setup UV-Stabilized Plastic: Withstands sun exposure without becoming brittle or discolored Why Pipe Supports Matter Water-filled pool hoses are heavy — they can weigh over 10 pounds when full. That weight hanging from your pool wall fittings puts constant stress on the connections, which leads to cracking and leaks over time. Pipe supports transfer this weight to the ground, protecting your pool's structure. Additionally, kinked hoses can reduce water flow by up to 50%, making your pump work harder for less circulation. Proper support keeps hoses at the optimal angle for maximum flow. Installation Position the pipe support on the ground under the hose at the desired height Choose the appropriate cradle — 1.25" or 1.5" — for your hose diameter Place the hose in the cradle Adjust the support height until the hose runs at a smooth angle with no kinks The integrated plunger valve is now positioned for easy access when you need to shut off flow FAQ Q: Do these work with 1.5" pool hoses?A: Yes. This kit includes fittings compatible with both 1.25-inch and 1.5-inch pool hoses, making it versatile for most above ground pool setups. Q: How do pipe supports help?A: Pool pipe supports prevent hoses from kinking or sagging, which restricts water flow and reduces pump efficiency. They also reduce stress on the pool wall fittings. Q: Are these easy to install?A: Yes. Simply position the support under the hose at the desired location and secure. No tools required in most cases. Q: Will this work with my Intex pool?A: Yes. Compatible with Intex, Bestway, Coleman, and most other above ground pool brands using standard hose sizes.Related Products Smart WiFi Sprinkler Controller 8-Zone — Weather Intelligent | iFJF 1.25" Pool Inlet Jet Nozzle Hose Holder & Strainer Grid for Above Ground Pools | 10-Pack Brass Pool Cover Anchor Collar Beauty Rings - Universal 9/16" ID | iFJF 10747 25010 Plunger Valve Assembly w/ O-Rings for Above Ground Pool Filter Pump 11872 Dual Split Hose Plunger Valve Connector for Above Ground Pool Pump | iFJF 📚 Related Guides & Articles iFJF Product Buying Guide — How to Choose the Right Part Diesel vs. Gas Engines: Complete Maintenance Guide 📖 Related Guide: Read our complete installation guide and comparison →

    $77.99

  • FDXLBKP1930 Keypad & Bezel Kit for Hayward H-Series Pool Heater — Front View

    iFJF iFJF FDXLBKP1930 Bezel and Keypad Assembly Replacement Kit - Compatible for Hayward

    Hayward H-Series Pool Heater Keypad & Bezel Assembly — FDXLBKP1930 Restore full control of your Hayward H-Series pool or spa heater with this complete FDXLBKP1930 keypad and bezel assembly. When your heater's membrane keypad becomes unresponsive, cracked, or worn from years of sun and chemical exposure, this direct-fit replacement brings your control panel back to life — no programming, no special tools required. Key Features Complete Assembly: Includes both the membrane keypad and the mounting bezel — everything you need in one kit OEM-Quality Construction: UV-resistant overlay prevents fading and cracking; sealed design protects against moisture and chemical exposure Plug-and-Play: Direct replacement for original Hayward part FDXLBKP1930 — connects to existing ribbon cable, no programming needed Enhanced Tactile Response: Crisp button feedback so you know each press registers — no more guessing if the heater received your command Weather-Resistant: Designed for outdoor pool equipment environments — withstands sun, rain, and pool chemical exposure Compatibility Specification Detail Part Number FDXLBKP1930 Fits Models Hayward H-Series Low NOx Pool/Spa Heaters Compatible Models H150FDN, H200FDN, H250FDN, H300FDN, H350FDN, H400FDN Type Membrane Keypad + Bezel Assembly Installation Plug-and-Play (No Programming) Common Symptoms That Indicate Replacement Buttons require multiple hard presses to register Display shows incorrect or flashing characters Keypad overlay is cracked, peeling, or faded Heater won't respond to temperature adjustments Error codes that persist after power cycling Installation Guide Turn off power to the pool heater at the breaker Remove the control panel cover screws Disconnect the old keypad ribbon cable carefully Remove the old bezel and keypad assembly Clean the mounting surface thoroughly Install the new FDXLBKP1930 assembly and connect the ribbon cable Reattach the control panel cover and restore power Test all button functions before closing up Frequently Asked Questions Q: Will this fit my Hayward H400FDN heater?A: Yes. The FDXLBKP1930 is compatible with all Hayward H-Series Low NOx models including H150FDN, H200FDN, H250FDN, H300FDN, H350FDN, and H400FDN. Q: Do I need to reprogram the heater after installation?A: No. This is a direct plug-and-play replacement. Your heater's settings are stored on the control board, not the keypad. Simply connect and turn on. Q: Is this an original Hayward part?A: This is a high-quality aftermarket replacement manufactured to meet or exceed OEM specifications for fit, finish, and durability. 🔗 Explore More from iFJF Find the right part for your vehicle or equipment: Browse All Products Fuel Filters Collection Auto Accessories

    $37.99

  • 350157 Union Kit for Pentair SuperFlo Pool Pump Complete Set with Gasket

    iFJF 350157 Union Kit for Pentair SuperFlo Pool & Spa Pumps — with Gasket | iFJF

    Out of stock

    Product Overview The 350157 Union Kit for Pentair SuperFlo Pool & Spa Pumps — with Gasket | iFJF is a precision-engineered replacement part designed to restore proper function and stop leaks in your pool or spa equipment. Manufactured to meet or exceed OEM specifications, this component delivers reliable, long-lasting performance at a fraction of the dealer price. Pool equipment operates in a harsh environment — constant exposure to chlorinated water, UV radiation, temperature swings, and pressure cycles. When seals, O-rings, and internal components degrade, the result is leaks, poor filtration, and higher operating costs. Key Features OEM-Spec Precision: Manufactured to exact dimensional tolerances for guaranteed fit without modifications. Chemical-Resistant Materials: EPDM, Viton, or chemical-grade polymers resist degradation from chlorine, bromine, salt, and UV. Extended Service Life: Premium materials deliver 2-3x the service life of economy alternatives. Easy DIY Installation: Straightforward replacement with basic hand tools — most jobs take 15-30 minutes. Value Pack Savings: Multi-pack options available — stock up and save vs buying singles when applicable. Compatibility Specification Detail Brand Pentair Pool & Spa Replaces Part # 350157, SW-21-350, 21063-350-000 Material EPDM Rubber / Engineered Polymer Application Residential & Light Commercial Pool/Spa When to Replace Visible Leaks: Water seeping from connections or housings = failed seal or gasket Decreased Performance: Reduced flow, poor filtration = worn internal components Unusual Noise: Grinding or squealing = worn bearings, gears, or impellers Age: Rubber seals should be replaced every 2-3 years as preventive maintenance Hard/Cracked Rubber: O-rings that feel hard or show surface cracks no longer seal properly Installation Tips Turn Off Equipment: Switch off at circuit breaker before working on pool equipment. Release Pressure: Open air relief valve on filter to release system pressure. Clean All Surfaces: Remove old gasket material and debris — clean surface = proper seal. Use Proper Lubricant: Silicone-based pool lube only. NEVER use petroleum jelly — it destroys EPDM. Tighten Evenly: Cross-pattern tightening for multi-bolt connections. Test Before Full Operation: Run briefly and check all connections. Frequently Asked Questions Q: Does this fit my SuperFlo VS pump?A: Yes. Fits all Pentair SuperFlo pumps: VS (variable speed), single-speed, two-speed, and high-performance models. Replaces OEM part numbers 350157, SW-21-350, and 21063-350-000. Q: What is included in the kit?A: One 2-inch union connector nut (threaded half), one 2-inch union tailpiece (slip half), and one EPDM gasket/O-ring. Single union set for one pump port. Most SuperFlo pumps need two kits (suction and discharge). Q: How do I stop my pump from leaking at the union?A: Common causes: 1) Over-tightening crushes gasket (hand-tighten + 1/4 turn only) 2) Old hardened gasket (replace every 3 years) 3) Misaligned pipe stress (support plumbing within 12 inches of pump) 4) Cracked union nut from freeze damage or overtightening. Q: Can I install without cutting plumbing?A: If replacing existing same-type union: yes. Unscrew old nut, swap gasket, reconnect. If tailpiece (glued half) needs replacement, you will need to cut and re-glue PVC pipe using primer and cement rated for pool/spa applications. Related Products Shop All Pool & Spa Parts → Pool Filter Cartridges & Grids → Related Guides & Articles Pool Filter Maintenance: Complete Seasonal Guide → How to Fix Common Pool Pump Problems →

    Out of stock

    $37.99

  • 385230325 Vacuum Breaker Kit for Sealand Traveler Toilets — Hand Sprayer

    iFJF 385230325 Vacuum Breaker Kit for Sealand Traveler Toilets — Hand Sprayer

    385230325 RV Toilet Vacuum Breaker Kit — Hand Sprayer — Stop Leaks & Prevent Backflow A leaking vacuum breaker on your RV toilet doesn't just waste water — it can siphon contaminated water back into your fresh water system, cause odors, and damage your bathroom floor. The iFJF 385230325 Vacuum Breaker Kit is the correct dual-port replacement for Dometic/Sealand Traveler and VacuFlush toilets equipped with a hand sprayer. Unlike single-port alternatives, this kit includes the dedicated sprayer connection port — no adapters, no leaks, no compromises. Complete kit includes vacuum breaker body, integrated dual-seal check valve, all O-rings and gaskets, and stainless steel mounting hardware. Measures 3.25" L × 1.73" W × 3.65" H for exact drop-in fit. Key Features Hand Sprayer Compatible: Dual-port design with dedicated sprayer connection — no T-fittings or adapters that create leak points. Specifically for toilets WITH a hand sprayer. Complete Kit: Vacuum breaker body (3.25"L × 1.73"W × 3.65"H), dual-seal check valve, all O-rings, gaskets, and stainless steel hardware — everything needed. Backflow Prevention: Dual-seal check valve prevents contaminated water from siphoning back into your fresh water plumbing. Meets ABYC and RVIA code requirements. Durable Materials: High-impact ABS body withstands years of vibration from road travel. Nitrile seals resist holding tank chemicals and marine sanitation products. DIY-Friendly: 20-30 minute installation with basic hand tools. 1/2" NPT connections match factory plumbing. Compatibility Brand Series Models / Notes Dometic / Sealand Traveler 110, 111, 210, 211, 510, 511 (with hand sprayer) Dometic / Sealand VacuFlush All models with hand sprayer attachment ⚠️ Not Sure Which Kit? If there's a coiled hose behind your toilet connected to the breaker → this is your kit. No hose → order 385316906 (no sprayer). Specifications Specification Detail Part Number 385230325 Dimensions 3.25"L × 1.73"W × 3.65"H Material ABS Body / Nitrile Seals / Stainless Steel Hardware Connection 1/2" NPT — Dual Port (Water Inlet + Sprayer) Check Valve Dual-Seal, Integrated Symptoms of a Failed Vacuum Breaker Water leaking or spraying from behind the toilet pedestal — especially when the hand sprayer is used Continuous slow drip from the breaker housing Bowl fails to hold water after flushing Sewage odor near the toilet (backflow through failed check valve) Reduced sprayer pressure or water hammer when flushing Installation Steps Shut off water supply to the toilet. Flush to relieve system pressure. Disconnect the hand sprayer hose and water supply line from the old breaker. Remove the old vacuum breaker (typically 2 screws or threaded collar). Clean mounting surface and inspect for cracks or damage. Install new breaker with supplied gaskets — 2-3 wraps of Teflon tape on threaded connections. Reconnect sprayer hose and water line, turn on supply, test all connections for leaks. Why Choose iFJF? iFJF vacuum breaker kits are manufactured to OEM Dometic/Sealand specifications with upgraded nitrile seals for extended service life — especially important in hot climates where rubber seals degrade faster. US-based support and fast shipping from our American warehouse. Related Products 385316906 Vacuum Breaker Kit — No Hand Sprayer 4036ER2004A Washer Tub Bearing & Seal Kit Pressure Gauge for Sand Filter Pump Frequently Asked Questions Q: Does this fit toilets without a hand sprayer?A: No. If your Sealand/Dometic toilet does NOT have a hand sprayer, you need the 385316906 (single-port) vacuum breaker kit. This 385230325 has a dedicated sprayer port. Q: How long does installation take?A: 20-30 minutes. Accessing the back of the toilet in tight RV bathrooms is typically the most time-consuming part. A compact mirror and headlamp make it easier. Q: Do I need thread sealant or Teflon tape?A: Yes. Apply 2-3 wraps of Teflon tape to male threaded connections. Do not use pipe dope or liquid sealants — they can degrade the nitrile seals. Q: Why does my breaker leak only when I use the hand sprayer?A: This is a classic sign of a failed check valve inside the vacuum breaker. The sprayer back-pressures the system, and a worn seal can't hold. Replacement is the fix. Q: Will this stop sewage odors?A: If the odor is from backflow through a failed vacuum breaker — yes. If caused by a failed floor flange seal or holding tank vent, those may need separate repair. 📚 Related Guides & Articles Complete Onan Quiet Diesel RV Generator Tune-Up Why You Need a Bluetooth Kill Switch for Your RV or Truck

    $27.99

  •  for   MX6, MX8, X6 — Front View | iFJF Direct

    iFJF R0527700 MX8 Pool Cleaner Hose Kit for MX6 MX8 Zodiac — Twist Lock Replacement

    Out of stock

    Product Overview Restore your pool cleaner's performance with the iFJF Pool Cleaner Hose Replacement Kit. Designed as a direct replacement for Zodiac MX6, MX8, and Baracuda X6 series automatic pool cleaners, this twist-lock hose kit features UV-resistant construction that withstands harsh pool chemicals and prolonged sun exposure. Whether your original hose has cracked, kinked, or lost suction, this replacement kit gets your pool cleaner back to peak efficiency. Key Features Twist-Lock Compatibility: Secure, leak-free connection with Zodiac MX6, MX8, and Baracuda X6 pool cleaners — no adapters needed. UV-Resistant Construction: Engineered to withstand prolonged sun exposure without becoming brittle or cracking — outperforms standard hoses in outdoor pool environments. Chemical-Resistant Material: Withstands chlorine, salt, and other pool treatment chemicals without degrading — maintains flexibility season after season. Crush-Proof Design: Reinforced walls prevent kinking and collapsing, ensuring consistent suction and cleaner movement throughout the pool. Easy DIY Replacement: Simply disconnect the old hose at the twist-lock fittings and connect the new one — no tools required. Compatibility Compatible Models Zodiac MX6, MX8, MX8 Elite, Baracuda X6, Baracuda X7 Connection Type Twist-Lock (¼-turn) Replaces OEM R0527700, X38210S When to Replace Your Pool Cleaner Hose Visible cracking or splitting on the hose surface Water leaks at connection points or along the hose body Kinks that won't straighten — restricting water flow Reduced cleaner movement — the cleaner moves slowly or gets stuck Loss of suction — debris pickup decreases noticeably Age over 2-3 seasons — preventive replacement before failure Installation Tips Turn off the pool pump before disconnecting any hoses Flush the new hose with clean water before connecting to remove any manufacturing residue Ensure twist-lock connections are fully seated — you should hear/feel a click Test the cleaner's movement pattern after installation to confirm proper operation Store hoses indoors during winter months to maximize lifespan Why Choose iFJF Direct? OEM-Spec Quality: Matches or exceeds original equipment specifications at a significantly lower price. Season-Ready: Get your pool cleaner working before swim season — fast shipping from US warehouses. Satisfaction Guarantee: Not satisfied? Return within 30 days for a full refund. Frequently Asked Questions Q: Which pool cleaners is this hose compatible with?A: This twist-lock hose kit is compatible with Zodiac MX6, MX8, MX8 Elite, Baracuda X6, and Baracuda X7 automatic pool cleaners. It uses the standard ¼-turn twist-lock connection found on these models. Q: How long will this replacement hose last?A: With proper care and off-season indoor storage, expect 2-4 years of service life. Factors affecting lifespan include: daily sun exposure, pool chemical levels, cleaner usage hours, and winter storage conditions. Q: How do I know which length I need?A: Measure from your pool's skimmer or dedicated suction line to the farthest point of the pool, then add 2-3 feet for proper coverage. Standard residential pools typically use 8-12 hose sections. Consult your cleaner manual for the manufacturer's recommendation. Q: Can I connect multiple hose sections together?A: Yes — the twist-lock connectors allow daisy-chaining multiple sections for larger pools. Each section twists and locks securely to the next, creating a continuous hose assembly. Q: Why is my pool cleaner moving slowly after replacing the hose?A: Check that all twist-lock connections are fully seated and there are no air leaks. Also verify the filter pump is running at full speed, skimmer baskets are clean, and the pool filter isn't due for backwashing. A small air leak at any connection point will reduce suction significantly.

    Out of stock

    $23.99

  • 2002244008 Freezer Door Hinge Plate Kit for 2-Way & 3-Way RV Refrigerators — front view image 1

    iFJF 2002244008 Freezer Door Hinge Plate Replacement Kit for 2-Way & 3-Way RV Refrigerators

    Overview The iFJF 2002244008 Freezer Door Hinge Plate Replacement Kit restores proper operation and sealing of your RV refrigerator's freezer compartment door. Over time, the original plastic hinge plates on Dometic and Norcold 2-way and 3-way absorption refrigerators become brittle, crack, or snap — leaving your freezer door sagging, misaligned, or completely detached. A door that doesn't seal properly forces the refrigerator to work harder, wastes propane or electricity, and can lead to food spoilage. This complete replacement kit includes both the upper and lower hinge plates needed to rebuild your freezer door mounting. Installation is straightforward and requires only basic hand tools — no refrigeration system knowledge or special skills needed. Save hundreds compared to the cost of replacing the entire refrigerator or paying for RV service center labor. Key Features Complete Hinge Replacement Kit — Includes upper and lower hinge plates, pivot pins, and mounting hardware for a thorough repair Restores Proper Door Seal — Correct door alignment ensures the freezer door gasket seals tightly, improving cooling efficiency Durable Construction — Manufactured from impact-resistant material superior to the brittle factory plastic that commonly fails Broad Compatibility — Fits most Dometic and Norcold 2-way (propane/120V) and 3-way (propane/120V/12V) RV refrigerators DIY-Friendly — Replace in approximately 20-30 minutes with a Phillips screwdriver — no special tools or skills required Prevents Further Damage — Addressing the hinge early prevents stress cracks from spreading to the door panel or refrigerator frame Technical Specifications Specification Details Part Number 2002244008 Compatible Refrigerators Dometic & Norcold 2-Way and 3-Way RV Absorption Refrigerators Includes Upper Hinge Plate, Lower Hinge Plate, Pivot Pins, Mounting Screws Material Impact-Resistant Engineered Plastic Installation Time Approx. 20-30 Minutes Compatibility Brand Type Compatibility Dometic RM, NDR, DM Series (2-Way & 3-Way) ✅ Compatible Norcold N Series (2-Way & 3-Way) ✅ Compatible ⚠️ Verify Before Ordering: This hinge kit fits standard freezer compartment doors on most Dometic and Norcold models. Measure your existing hinge plate dimensions and compare with product photos to confirm fitment for your specific refrigerator model. Installation Guide Empty Freezer — Remove all items from the freezer compartment Remove Door — Carefully lift the freezer door off its hinge pins (may require gentle upward pressure if the bottom hinge is still intact) Remove Old Hinge Plates — Unscrew the broken hinge plates from the refrigerator frame using a Phillips screwdriver Clean Mounting Points — Remove any debris or broken plastic fragments from the hinge mounting area Install New Hinge Plates — Screw the new iFJF upper and lower hinge plates into position; do not overtighten Rehang Door — Align the door pivot points with the new hinges and lower the door into place Test Operation — Open and close the door several times to verify smooth operation and proper gasket seal FAQ Q: How do I know if my freezer door hinge is the problem?A: Signs include: the freezer door sagging or not aligning with the refrigerator frame, difficulty closing the door completely, visible cracks or breaks in the plastic hinge plates, the door falling off when opened past a certain angle, or frost buildup inside the freezer from a poor door seal. Q: Will this kit fit both upper and lower hinges?A: Yes. The kit includes both the upper and lower hinge plates, so you can replace one or both as needed. Even if only one hinge is broken, replacing both ensures even wear and proper alignment. Q: Why did my original hinge plates break?A: The original plastic hinge plates used on many RV refrigerators become brittle over time due to temperature cycling (hot during storage, cold during operation), UV exposure through RV windows, and simply age. The freezer door's weight stresses these small plastic components, and they eventually fatigue and crack. Q: Can I install this without removing the refrigerator from the RV?A: Yes. The freezer door hinge plates are accessible from the front of the refrigerator while it remains installed in the RV cabinetry. No need to disconnect propane, electrical, or remove the refrigerator from its enclosure. Q: Will this hinge kit improve my refrigerator's cooling performance?A: If your freezer door wasn't sealing properly due to hinge misalignment, yes — restoring a proper seal prevents cold air loss and reduces the refrigerator's workload. You may notice faster cool-down times and more consistent temperatures after the repair. Q: Is this compatible with both propane and electric operation?A: The hinge plates have no interaction with the cooling system — they are purely mechanical door mounting components. They work identically whether your refrigerator is operating on propane, 120V AC, or 12V DC. Q: Can I replace just the door gasket while I'm at it?A: If your freezer door gasket is also worn, cracked, or compressed, replacing it along with the hinges is a good idea. However, the gasket is a separate part and not included in this hinge kit. Inspect the gasket while the door is off and consider replacement if it shows signs of wear. Q: How does this compare to the OEM Dometic/Norcold hinge?A: This aftermarket hinge kit is manufactured to OEM specifications with equivalent or improved material durability. Many RV owners report the aftermarket replacement outlasts the OEM hinge due to improved impact-resistant material formulation. 📚 Related Guides & Articles iFJF Guides & Resources — Expert Tips, Installation Tutorials & Buying Guides

    $22.99

  • iFJF Micro P-711 Refrigerator Control Circuit Board fit 2-Way and 3-Way Models Replace RV Black Box Part Electronics Main Power Control Board

    iFJF iFJF Micro P-711 Refrigerator Control Circuit Board fit 2-Way and 3-Way Models Replace RV Black Box Part Electronics Main Power Control Board

    Universal RV Refrigerator Control Board — Micro P-711 The Micro P-711 is the industry-standard replacement control board for Dometic and Norcold RV refrigerators. If your fridge has stopped cooling, the control board is the most common failure point — and this board is the most reliable replacement available, compatible with over 30 refrigerator models. Key Features Built-in Temperature Adjustment — Precise thermistor-based control for safe food storage Automatic System Detection — Self-configures for 2-way (LP gas/120V) or 3-way (LP/120V/12V) operation Surge Protection — Improved circuit protection against campground power fluctuations Food Saver Feature — Automatic restart attempt after power loss to protect food Enhanced Thermocouple Circuit — More reliable flame sensing for LP gas operation Moisture-Resistant Coating — Conformal coating protects against humidity and condensation Replaces Part Numbers Direct replacement for boards starting with "293" — including: 2931842.01-04, 2931843.01-04, 2932691.017, 2932177.01, 2932695.01, 2932770.01, 2932881.01/.010, and more. Compatible Models (Partial) S1521, S1531, S1621, S1631, S1821, S1831, NDR1062, NDR1272, NDR1282, NDR1292, NDR1492, RM2551-4, RM2607, RM2611-2, RM2652, RM2807, RM2811-2, RM2852, RM3607, RM3662-3, RM3807, RM3862-3, RM4872-3, RM7030, RM7130, RM7732, RM7832 — and many more. Installation Disconnect ALL power sources — 120V AC, 12V DC, and LP gas Remove refrigerator access panel Photograph existing wiring connections for reference Disconnect old board and remove mounting screws Mount new Micro P-711 board and reconnect wiring per labeled terminals Restore power and test on all modes (AC, DC, LP) Frequently Asked Questions Q: How do I know if my control board is bad?A: Symptoms: fridge not cooling on any mode, no display lights, clicking but no ignition, intermittent operation, or error codes. Q: Is this plug-and-play?A: Yes. Connectors are clearly labeled. Works with original or updated wiring. Manual included. Q: Does this work with my older Dometic fridge?A: If your board part number starts with '293', the P-711 is a direct replacement. Q: Will this fix gas operation issues?A: If the control board is the cause, yes. The P-711 has an improved thermocouple circuit. Q: Do I need a technician?A: Most DIYers can install in under 30 minutes. Disconnect all power sources first!

    $77.99

  • CLX200C Cover Cap for Hayward CL200 CL220 Chlorine & Bromine Feeder — Black

    iFJF CLX200C Cover Cap for Hayward CL200 CL220 Chlorine & Bromine Feeder — Black

    Out of stock

    Product Overview Direct replacement cover cap for Hayward CL200 and CL220 series automatic chlorine and bromine chemical feeders. Manufactured from UV-stabilized, chemical-resistant polymer that withstands continuous exposure to chlorine, bromine, and muriatic acid without cracking, fading, or degrading. Precision-matched thread profile ensures a leak-free seal with CL200/CL220 feeder bodies every time. Key Features Chemical-Resistant Polymer — UV-stabilized, chemical-resistant material withstands chlorine, bromine, and acid without degradation or cracking. Precision Thread Fit — CNC-matched thread profile ensures leak-free seal on CL200/CL220 feeder bodies — no leaks or cross-threading. UV-Stabilized Design — Resists sun damage and discoloration from outdoor equipment pad exposure season after season. Tool-Free Installation — Ergonomic grip allows secure hand-tightening without any tools. O-ring groove for positive seal every time. Universal Hayward Fit — Compatible with CL200 (chlorine) and CL220 (bromine) feeders in both inline and offline configurations. Compatibility Make Model Year Range Notes Hayward CL200 Series All Years Chlorine Feeder — Inline & Offline Hayward CL220 Series All Years Bromine Feeder — Inline & Offline Hayward CL200A / CL220A All Variants Direct Fit — No Modifications Specifications Specification Value Material UV-Stabilized Chemical-Resistant Polymer Color Black Replaces Part# CLX200C, CLX200CAP Installation Hand-Tighten (No Tools Required) Why Choose iFJF Over time, chemical exposure causes original caps to crack, warp, or lose their seal — leading to chlorine gas leaks. Our replacement cap restores proper seal and extends feeder life without the cost of a full unit replacement. Frequently Asked Questions Q: Will this fit my Hayward feeder?A: Fits all Hayward CL200 and CL220 series feeders. Contact us with your model number if unsure. Q: Do I need tools to install?A: No. Hand-tighten until snug. Ensure the O-ring is seated properly before threading on. Q: Is this OEM Hayward?A: High-quality aftermarket replacement manufactured to meet OEM CLX200C specs — same fit at better value. Q: Will chlorine damage this cap?A: No. The chemical-resistant, UV-stabilized polymer is formulated for continuous chlorine and bromine exposure. Q: How often should I replace it?A: Inspect each pool season. Replace if cracked, warped, or losing seal. Typical life: 3–5 seasons. Q: What if my old cap is stuck?A: Turn off pump and relieve pressure. Use a strap wrench — never metal tools. Apply silicone lube to threads. Related Products Complete your pool maintenance: CCX1000V Pool Filter Cartridge for Hayward filters, Pressure Gauge for monitoring, and O-Ring & Gasket Kit for complete feeder seal replacement.

    Out of stock

    $39.99

Home & Garden Essentials

From garden tools and outdoor equipment to home improvement supplies, iFJF Direct carries a practical selection of home and garden products to keep your property in top shape.

Popular Categories

  • Garden Tools: Pruners, shears, sprayers, and hand tools for lawn and garden care
  • Outdoor Equipment: Replacement parts and accessories for lawn mowers, trimmers, and power equipment
  • Home Improvement: Hardware, fittings, and utility items for DIY projects
  • Seasonal Items: Summer and winter essentials for home maintenance

© 2026 iFJF Direct | Sitemap

    • American Express
    • Diners Club
    • Discover
    • Maestro
    • Mastercard
    • PayPal
    • Visa

    Login

    Forgot your password?

    Don't have an account yet?
    Create account