Products

Product Overview Keep your RV refrigerator cooling properly with the iFJF 618548 Thermistor Assembly. This critical temperature sensor monitors the refrigerator's interior temperature and communicates with the control board to regulate cooling. Compatible with Norcold N6, N8, 900, and 9000 series RV refrigerators, this complete assembly includes the thermistor probe and wire harness for a straightforward plug-in replacement. A faulty thermistor is one of the most common causes of RV refrigerator problems — symptoms include inconsistent temperatures, food freezing in the fridge section, the refrigerator running too warm, or error codes on the display. Replacing the thermistor is a simple, inexpensive fix that often resolves these issues without expensive service calls. Key Features Complete Assembly: Thermistor probe + wire harness — everything needed for replacement Exact Fit: Designed specifically for Norcold N6, N8, 900, and 9000 series Accurate Sensing: Precision temperature measurement ensures proper cooling control Easy Plug-In: Pre-terminated connector plugs directly into the control board Replaces Multiple Part Numbers: 618548, 621742, and equivalents 📋 Compatibility Compatible Refrigerator Models Norcold N6 Series (N611, N621, N641) Norcold N8 Series (N811, N821, N841) Norcold 900 Series Norcold 9000 Series Replaces part numbers: 618548, 621742 📐 Specifications Specification Value Part Number 618548 Replaces 621742 Type NTC Thermistor (Negative Temperature Coefficient) Includes Sensor probe + wiring harness with connector Application RV absorption refrigerator temperature sensing ❓ Frequently Asked Questions Q: What are signs of a bad thermistor?A: Common symptoms: refrigerator temperature fluctuating widely, food freezing in the fridge section, fridge not cooling properly, or error codes E1/E2 on the display panel. Q: Does this include the wiring harness?A: Yes. This is a complete assembly including the thermistor probe and the wiring harness with plug connector. Q: How do I install the new thermistor?A: The thermistor is typically clipped to the cooling fins inside the refrigerator. Unplug the old one, slide it off the fin, slide the new one on, and plug in the connector. It takes about 5 minutes. Q: Will this work for my Norcold N811?A: Yes. The N811 is part of the N8 series and this thermistor assembly is fully compatible. Q: Does the thermistor require any calibration?A: No. The thermistor is pre-calibrated and works immediately after installation.

Read more less

61N-24560 Fuel Filter Assembly — Yamaha Outboard OEM Replacement Your Yamaha outboard deserves clean fuel. The iFJF 61N-24560 Fuel Filter Assembly is a complete drop-in replacement for Yamaha 9.9HP through 40HP outboard motors—covering both 2-stroke and 4-stroke models. This complete assembly includes the filter element, transparent housing bowl, mounting bracket, and all necessary O-rings and seals. It replaces Yamaha OEM part numbers 61N-24560-00-00 and 68T-24251-00-00 with identical fit and function. Key Features Complete Assembly: Includes filter element, transparent bowl, bracket, and all seals—no hunting for separate parts Clear Bowl Design: Transparent housing lets you visually inspect fuel condition and water accumulation at a glance High-Capacity Filtration: 10-micron filtration media captures rust, sediment, and debris before they reach your carburetor or injectors Marine-Grade Materials: Corrosion-resistant construction stands up to saltwater environments and ethanol-blended fuels Easy Installation: Factory mounting pattern—bolts right in using existing hardware in under 15 minutes Compatibility Brand Horsepower Range Stroke Yamaha Outboard 9.9HP, 15HP, 20HP 2-Stroke & 4-Stroke Yamaha Outboard 25HP, 30HP, 40HP 2-Stroke & 4-Stroke Specifications Specification Detail Part Number 61N-24560 / FJ-WSFF05 Replaces OEM 61N-24560-00-00, 68T-24251-00-00 Filtration Rating 10 Micron Bowl Material Transparent Nylon Polymer Why Replace Your Fuel Filter? Ethanol-blended fuel absorbs moisture over time, leading to phase separation and water in your fuel system. A clogged filter starves your engine, causing hard starts, rough idle, and power loss at WOT. If your outboard sat for more than 6 months or you have been running ethanol fuel, it is time for a new filter assembly. Frequently Asked Questions Q: Will this fit my Yamaha 25HP 4-stroke?A: Yes. The 61N-24560 assembly fits Yamaha 4-stroke outboards from 9.9HP through 40HP. It is a direct bolt-on replacement. Q: Does this come with mounting hardware?A: The assembly includes the filter with pre-installed mounting bracket. You reuse the existing bolts from your old assembly to mount it. Q: How often should I change this filter?A: Yamaha recommends annual replacement or every 100 hours. In commercial applications, inspect every 50 hours. Q: Can I use this with E10 ethanol fuel?A: Yes. The assembly is compatible with gasoline containing up to 10% ethanol. For E15 or higher, consult your engine manual. Q: Is this genuine Yamaha?A: Premium aftermarket replacement manufactured to OEM specifications at a fraction of the dealer price. Related Marine Products 65L-24563-00-00 Fuel Filter 2-Pack for Yamaha F150-F225 Helpful Articles iFJF Blog — Marine Maintenance Tips

Read more less

Product Overview Get your Norcold RV refrigerator working again with the iFJF 621991001 Refrigerator Power Board Kit. This replacement control board is the brain of your RV absorption refrigerator, managing power between 120V AC and LP gas operation. Designed for Norcold N611, N811, N610, and N810 series models with serial numbers below 9056491, this board restores all control functions including temperature settings, mode selection, and diagnostic capabilities. When the power board fails, your refrigerator may not turn on at all, won't switch between AC and gas, displays error codes, or runs but doesn't cool. Rather than replacing an expensive RV refrigerator, this affordable board replacement gets you back on the road. Key Features Direct Replacement: Designed for Norcold N611, N811, N610, N810 series (serial # below 9056491) Dual Power Control: Manages both 120V AC electric and LP gas operation Built-In Diagnostics: Compatible with Norcold's diagnostic system for easy troubleshooting Plug-and-Play: Uses the same connectors and mounting points as the original board Quality Electronics: Industrial-grade PCB with protective coating for RV environment durability 📋 Compatibility Compatible Models (Serial # Below 9056491) Norcold N611 Series Norcold N811 Series Norcold N610 Series Norcold N810 Series 📐 Specifications Specification Value Part Number 621991001 Type 2-Way Power Control Board (AC/Gas) Compatible Models N611, N811, N610, N810 (SN < 9056491) Input Voltage 120V AC / 12V DC ❓ Frequently Asked Questions Q: How do I check my serial number?A: The serial number is on a label inside the refrigerator, typically on the side wall or near the door frame. This board fits models with serial numbers BELOW 9056491. Q: What are symptoms of a bad power board?A: Refrigerator won't turn on, won't switch between AC and gas mode, error codes on display, clicking but no ignition on gas mode, or display lights but no cooling. Q: Is this a plug-and-play replacement?A: Yes. The board uses the same connectors as the original — remove the old board, plug in the new one, and secure with the original mounting screws. Q: Do I need to disconnect both AC and DC power?A: Yes. Disconnect shore power AND the RV battery before replacing the board. The control board uses both 120V AC and 12V DC power. Q: Will this fix error code 'no co' (no cooling)?A: Possibly. The 'no co' code can be caused by a faulty power board. However, it can also indicate burner, thermocouple, or cooling unit issues. Start with the board as it's the most common and affordable fix.

Read more less

Product Overview Restore your Norcold RV refrigerator to full operation with the iFJF 628661 Refrigerator Power Circuit Board Kit. This essential control board manages all electrical functions in your Norcold absorption refrigerator, including AC power operation, gas ignition control, temperature regulation, and display panel communication. Compatible with a wide range of Norcold models including N41X, N51X, N6X, N8X, NXA, and N1095 series. RV refrigerators rely on complex control electronics that are exposed to vibration, temperature extremes, and power fluctuations. When the board fails, your food spoils and your trip is disrupted. This direct replacement board solves the problem quickly without the expense and wait of dealership service. Key Features Broad Compatibility: Fits N41X, N51X, N6X, N8X, NXA, and N1095 series Norcold refrigerators Full Function Control: AC heating element, gas valve, ignition, temperature sensing, and display OEM-Spec Design: Matches factory board layout, connectors, and mounting dimensions Built-in Diagnostics: Supports Norcold's self-diagnostic system for troubleshooting Protected Electronics: Conformal coating protects against humidity and condensation inside the RV 📋 Compatibility Compatible Norcold Series Norcold N41X Series Norcold N51X Series Norcold N6X Series (N611, N621, N641) Norcold N8X Series (N811, N821, N841) Norcold NXA Series Norcold N1095 Series 📐 Specifications Specification Value Part Number 628661 Type 2-Way Refrigerator Power Control Board Compatible Models N41X, N51X, N6X, N8X, NXA, N1095 Power Input 120V AC / 12V DC ❓ Frequently Asked Questions Q: Which Norcold models does this fit?A: This board fits N41X, N51X, N6X, N8X, NXA, and N1095 series Norcold RV refrigerators. Check your model number on the inside label to confirm. Q: What's the difference between 628661 and 621991001?A: These are different boards for different model families. The 628661 fits N41X/N51X/N6X/N8X/NXA/N1095, while the 621991001 fits N611/N811/N610/N810 (below serial #9056491). Choose based on your model. Q: How do I know if this is the right board?A: Check your refrigerator model number (inside door frame label) and verify against the compatibility list. If your existing board has part number 628661, this is a direct replacement. Q: Does the board come with installation instructions?A: Basic installation guidance is included. Installation involves unplugging the old board and connecting the new one to the same connectors. We recommend taking a photo of the wiring before disconnecting. Q: Is this board new or refurbished?A: This is a brand new, factory-tested board. iFJF does not sell refurbished electronics.

Read more less

Product Overview Fix the unresponsive touch panel on your Norcold RV refrigerator with the iFJF 630762 Refrigerator Optical Control Board. This component is the interface between the front panel touch controls and the main power board on Norcold N611 and N811 series refrigerators. When it fails, the display goes blank, buttons become unresponsive, or the refrigerator won't respond to temperature adjustments. This optical control board is compatible with the optical board kit 637775 and fits ALL N611 and N811 model refrigerators — unlike some boards that are serial number-specific. It's the go-to fix for display and control panel issues on these popular Norcold models. Key Features Universal N611/N811 Fit: Compatible with ALL N611 and N811 models, regardless of serial number Optical Interface: Uses optical communication to isolate the user interface from high-voltage circuits — safer and more reliable Plug-and-Play: Uses the same connectors and mounting as the original board Fixes Common Issues: Blank display, unresponsive buttons, temperature setting problems Kit Compatible: Replaces boards in optical board kit 637775 📋 Compatibility Compatible Models Norcold N611 (ALL serial numbers) Norcold N811 (ALL serial numbers) Compatible with optical board kit 637775 📐 Specifications Specification Value Part Number 630762 Kit Reference 637775 Type Optical Control / Display Interface Board Compatible Models N611, N811 (all serial numbers) ❓ Frequently Asked Questions Q: What does the optical control board do?A: It's the interface between the touch control panel on the front of your refrigerator and the main power board. It uses optical (light-based) communication to isolate the touch controls from high-voltage circuits. Q: My display is blank — will this fix it?A: If the refrigerator has power (interior light works) but the display is blank or unresponsive, the optical control board is the most likely cause. Replacing it often resolves this issue. Q: Does this fit all N611 models?A: Yes. Unlike some Norcold boards that are serial number specific, the 630762 optical board fits ALL N611 and N811 models. Q: How difficult is the installation?A: Moderate difficulty. The board is located behind the front control panel. You'll need to remove the panel trim, disconnect the old board, and install the new one. A YouTube tutorial for Norcold N611 control board replacement is recommended. Q: Do I need to disconnect power before installing?A: YES. Always disconnect both 120V shore power AND 12V battery power before working on any RV refrigerator electronics.

Read more less

Product Overview Maintain crystal-clear, bacteria-free water in your pool or spa with the iFJF 6472-841 UV Replacement Bulb. This high-output ultraviolet lamp is designed for ClearRay XL water sanitization systems, using UV-C light to neutralize bacteria, viruses, algae, and other microorganisms without chemicals. Compatible with 6472-857 bulb specifications, it's the essential replacement to keep your UV sanitizer operating at peak efficiency. UV bulbs lose effectiveness over time — even if they still glow, their germicidal output drops significantly after 12 months of use. Replacing your UV bulb annually ensures your ClearRay system continues to provide effective, chemical-free water treatment that's gentle on skin and eyes. Key Features UV-C Germicidal Output: Emits 254nm wavelength UV-C light proven to neutralize 99.9% of waterborne pathogens ClearRay XL Compatible: Direct replacement for ClearRay XL pool and spa UV sanitization systems Cross-Compatible: Replaces both 6472-841 and 6472-857 bulb specifications Long Service Life: Rated for approximately 9,000 hours of continuous operation (about 12 months) Easy Installation: Standard 4-pin base — unplug old bulb, plug in new one Chemical-Free Sanitation: Reduces chlorine/bromine demand by destroying microorganisms before they multiply 📋 Compatibility Compatible Systems ClearRay XL UV Sanitization System 6472-841 replacement applications 6472-857 replacement applications Pool and spa UV water treatment systems using 4-pin UV-C lamps 📐 Specifications Specification Value Part Numbers 6472-841 / 6472-857 Lamp Type UV-C Germicidal (254nm) Base Type 4-Pin (standard UV lamp base) Rated Life ~9,000 hours Application Pool & spa UV water sanitization Why Replace Your UV Bulb Annually? Declining Output: UV-C output drops 30-40% after 9,000 hours — your water isn't being properly sanitized even if the bulb glows Algae Prevention: A strong UV system prevents algae blooms before they start, reducing chemical usage and shock treatments Health & Safety: UV sterilization kills chlorine-resistant pathogens like Cryptosporidium that can survive in chemically treated water Equipment Protection: A properly functioning UV system prevents biofilm buildup in plumbing and equipment Installation Instructions Turn off power to the UV sanitizer at the circuit breaker Allow the bulb to cool for 15 minutes if recently operated Remove the UV chamber cover according to manufacturer instructions Carefully unplug the old bulb from its 4-pin socket DO NOT touch the new bulb glass with bare hands — use the included sleeve or clean gloves Insert new bulb into socket and reassemble chamber cover Restore power and verify operation ❓ Frequently Asked Questions Q: How often should I replace this UV bulb?A: UV bulbs should be replaced every 12 months (approximately 9,000 hours of operation). Even if the bulb still glows, its germicidal UV-C output drops significantly after one year. Q: Does this fit my ClearRay XL system?A: Yes. This 6472-841 bulb is designed as a direct replacement for ClearRay XL UV sanitization systems used in pools and spas. Q: What's the difference between 6472-841 and 6472-857?A: These are cross-compatible bulb specifications. This replacement bulb meets both 6472-841 and 6472-857 requirements. Q: Can I touch the bulb with my bare hands?A: NO. Oils from your skin create hot spots on the quartz glass that can cause premature failure. Always handle by the ceramic base or use clean gloves. Q: Will this reduce my chlorine usage?A: Yes. UV sterilization neutralizes microorganisms before they can multiply, reducing the chlorine demand by 25-50% depending on bather load and environmental conditions.

Read more less

6598492 & 6598362 Air Filter Kit — Bobcat Skid Steer Loader Replacement Keep your Bobcat skid steer loader breathing clean in the harshest job site conditions. The iFJF 6598492 and 6598362 Air Filter Kit provides a complete dual-element filtration solution for Bobcat 600, 700, 800, 1200, and S-series loaders. This kit includes both the 6598492 primary outer filter and the 6598362 safety inner filter, replacing Bobcat OEM part numbers 42222 and 42223. The dual-stage design captures coarse debris with the outer element while the inner safety element protects during filter changes. Key Features Complete Dual-Element Kit: Includes both 6598492 outer primary filter and 6598362 inner safety filter Heavy-Duty Filtration: Multi-layer cellulose-synthetic blend media rated for dusty construction and agricultural environments High Dirt-Holding Capacity: Deep pleat design extends service intervals—more working time, less maintenance Precision Fit: Molded polyurethane end caps with factory-spec inner diameter for airtight seal Safety Element Protection: Inner filter prevents debris from entering intake during primary filter changes Compatibility — Bobcat Skid Steer Loaders Series Models 600 Series 641, 643, 645 700 Series 741, 743, 751, 753, 763 800 Series 843, 853 1200 Series 1213 S Series S130, S150 Specifications Specification Detail Part Number 6598492 + 6598362 / FJ-8492-ZH Replaces OEM 42222, 42223 Filter Type Dual-Element Dry Air Filter Primary Media Cellulose/Synthetic Blend Frequently Asked Questions Q: Do I need to replace the inner filter every time?A: The inner safety filter lasts through 2-3 outer filter changes. If the outer filter was damaged or dusty conditions, replace both together. Q: Will this kit fit my Bobcat 753?A: Yes. The 6598492/6598362 kit is the correct set for Bobcat 753 and all listed models. Q: Is this genuine Bobcat?A: Premium aftermarket kit manufactured to OE specifications in ISO 9001-certified facilities at significant savings. Q: How often should I service the air filter?A: Inspect daily. Replace outer filter at restriction indicator red or every 500 hours. Dusty conditions: every 250 hours. Q: Can I clean and reuse these filters?A: No. Replaceable dry elements. Compressed air can create micro-tears invisible to the eye. Related Bobcat Parts 6667352 Fuel Filter Water Separator for Bobcat Helpful Articles iFJF Blog — Heavy Equipment Maintenance

Read more less

65L-24563-00-00 Fuel Filter 2-Pack — Yamaha F150/F200/F225 Outboard Protect your Yamaha four-stroke outboard's expensive fuel injection system with the iFJF 65L-24563-00-00 Fuel Filter 2-Pack. This value pack gives you two OEM-equivalent filter elements at a bulk discount—keeping you on the water longer with a spare ready for your next service. Designed for Yamaha F150, F200, F225, and SX250 four-stroke outboards, this 10-micron filter captures water, sediment, and debris before they can clog injectors or cause lean running conditions. Key Features Bulk 2-Pack Value: Save 25% vs buying two singles—always have a spare filter on hand for your next service interval 10-Micron Filtration: High-efficiency media captures 99% of particles 10 microns and larger, protecting precision injectors Water-Separating Media: Specially treated cellulose media coalesces water droplets, preventing them from reaching the fuel rail Factory-Spec Fit: Identical dimensions and seal geometry to OEM filter—no leaks, no bypass Ethanol Compatible: Filter media and seals rated for gasoline with up to 10% ethanol (E10) Compatibility Brand Engine Years Yamaha Outboard F150 (2.7L 4-Stroke) 2004-Present Yamaha Outboard F200 (3.3L/2.8L 4-Stroke) 2001-Present Yamaha Outboard F225 (3.3L 4-Stroke) 2001-Present Yamaha Outboard SX250 (4.2L 4-Stroke) 2012-Present Specifications Specification Detail Part Number 65L-24563-00-00 / WSFF08-LX-2 Pack Size 2 Filters Filtration Rating 10 Micron Media Type Water-Separating Cellulose Why Replace Your Fuel Filter Regularly? Yamaha F150-F225 outboards use high-pressure direct fuel injection. A partially clogged filter causes the high-pressure pump to work harder, cavitate, and eventually fail—a repair exceeding $1,500. A $15 filter change is the smartest preventive maintenance you can perform on these engines. Frequently Asked Questions Q: Will this filter fit my 2015 Yamaha F200?A: Yes. The 65L-24563-00-00 is correct for Yamaha F200 four-stroke outboards from 2001 to present. Q: How do I change the fuel filter on my F150?A: Use a 36mm socket to unscrew the filter cap, replace the element and O-ring, torque to 13 ft-lbs. Instructions included. Q: Can I use this filter with E10 fuel?A: Yes. Rated for gasoline with up to 10% ethanol. Use a fuel stabilizer if the boat sits for extended periods. Q: Is this compatible with the Yamaha F250?A: No. The F250 uses a different filter (6P3-24563-00). Check your engine part number before ordering. Q: Why buy a 2-pack?A: Most owners perform annual filter changes. The 2-pack gives you this year's filter plus next year's spare at 25% off. Related Yamaha Marine Products 61N-24560 Fuel Filter Assembly for Yamaha 9.9-40HP Helpful Articles iFJF Blog — Marine Outboard Maintenance

Read more less

6667352 Fuel Filter Water Separator — Bobcat Skid Steer OEM Replacement Diesel fuel contamination is the number one cause of injection pump failure in Bobcat skid steers. The iFJF 6667352 Fuel Filter Water Separator provides dual-action protection—filtering particles to 10 microns while simultaneously separating emulsified water from diesel fuel. This direct replacement for Bobcat OEM 6667352 fits a wide range of Bobcat skid steer loaders from the 453 through 863 series, including popular models like the 753, 763, and 853. Key Features Dual-Action Filtration: 10-micron particle filtration plus water separation in a single spin-on canister High-Efficiency Water Removal: Hydrophobic media strips over 95% of emulsified water from diesel fuel Heavy-Duty Construction: Thick-gauge steel canister with corrosion-resistant coating Spin-On Design: Tool-free installation with pre-lubricated gasket for proper seal every time Universal Diesel Compatibility: Works with standard number 2 diesel, biodiesel blends up to B20 Compatibility Series Models 400 Series 453, 463 500 Series 553 600 Series 653 700 Series 751, 753 800 Series 853, 863 Specifications Specification Detail Part Number 6667352 / FJ-7352-1 Filter Type Spin-On Fuel/Water Separator Filtration 10 Micron Water Separation >95% Efficiency Warning Signs Your Filter Needs Replacement Engine sputtering or stalling under load Hard starting after sitting overnight Visible water in separator bowl Loss of power at high RPM Excessive white smoke from exhaust Frequently Asked Questions Q: Will this fit my Bobcat 753 with Kubota engine?A: Yes. Correct replacement for Bobcat 753 with Kubota, Deutz, and Perkins diesel engines. Q: How do I prime after changing?A: Fill new filter with clean diesel before spinning on. Use manual primer pump until firm resistance. Do not use starting fluid. Q: Change interval?A: Every 500 hours. Questionable fuel or wide temperature swings: every 250 hours. Q: Is this OEM?A: Premium aftermarket made to OE specifications at significant savings over dealer pricing. Q: Biodiesel compatible?A: Yes, up to B20. Higher blends may require more frequent changes. Related Bobcat Parts 6598492 Air Filter Kit for Bobcat Loaders Helpful Articles iFJF Blog — Diesel Engine Maintenance

Read more less

68052292AA Cabin Air Filter Access Door — Ram 1500-5500 (2011-2020) If your Ram truck's cabin air filter door has broken clips, fallen off, or gone missing, you are breathing unfiltered air and your HVAC system is sucking in leaves, dust, and debris. The iFJF 68052292AA Cabin Air Filter Access Door is a direct OEM-spec replacement that restores full filtration in under 5 minutes. This access door replaces Mopar part numbers 68052292AA and 68318365AA with identical fit, clip design, and material specification. Key Features OEM-Spec Fit: Precision-molded to factory dimensions—clips engage securely with no rattling Durable ABS Construction: Impact-resistant ABS plastic withstands temperature extremes from -40F to 180F Tool-Free Installation: Snap-in design—no tools, screws, or adhesives required Restores Full Filtration: Properly seals cabin air filter compartment, forcing all air through filter element Visible Quality Upgrade: Clean factory finish—no more unsightly duct tape on your glove box area Compatibility Vehicle Years Ram 1500 2011-2020 Ram 2500 / 3500 2011-2020 Ram 4500 / 5500 2011-2020 Specifications Specification Detail Part Number 68052292AA / FJ-AF92AA Replaces 68052292AA, 68318365AA Material ABS Plastic Installation Snap-In (No Tools) Installation Steps Open glove box and empty contents Squeeze glove box sides inward to release stops Locate cabin air filter access door behind glove box on HVAC housing Remove old door by releasing clips Insert new cabin air filter if needed (sold separately) Snap new 68052292AA door into place—listen for clips to engage Return glove box to normal position Frequently Asked Questions Q: Will this fit my 2018 Ram 2500?A: Yes. Fits all Ram 1500-5500 models from 2011-2020, regardless of engine or trim. Q: My original door broke—is this common?A: Yes, very common. Factory clips become brittle and snap during filter changes. Our replacement uses impact-modified ABS. Q: Does this include a cabin air filter?A: No, access door only. Cabin air filters sold separately. Replace filter at the same time while you have access. Q: Do I need special tools?A: No tools needed. Snap-in design—align clips and press into place. Q: Same as dealer part?A: Manufactured to identical specifications at a fraction of the Mopar dealer price. Related Ram Truck Parts 68157291AA Fuel Filter Kit for Ram 6.7L Cummins 68157291AA Fuel Filter for Ram 6.7L Cummins Helpful Articles iFJF Blog — Ram Truck DIY Maintenance

Read more less

68157291AA and 68436631AA Fuel Filter Kit — 2019-2020 Ram 6.7L Cummins Service your 5th-gen Ram HD's fuel system the right way with the iFJF 68157291AA and 68436631AA Complete Fuel Filter Kit. This two-filter kit covers both the front chassis-mounted filter and the rear engine bay filter—everything for a full fuel system service in one box. Designed for 2019-2020 Ram 2500/3500 with 6.7L Cummins. Also replaces Mopar 68065608AA and Fleetguard PF46152. Key Features Complete Two-Filter Kit: Both 68157291AA (front chassis) and 68436631AA (rear engine bay) included 3-Micron Absolute Filtration: Protects CP4.2 high-pressure fuel pump from catastrophic contamination failure Water Separation: Front filter strips moisture from diesel to prevent injector corrosion OEM-Dimension Seals: Factory-spec O-ring geometry ensures leak-free installation Bulk Kit Savings: Both filters together save vs buying individually Compatibility Vehicle Engine Years Ram 2500 6.7L Cummins Turbo Diesel 2019-2020 Ram 3500 6.7L Cummins Turbo Diesel 2019-2020 Ram 4500/5500 6.7L Cummins Turbo Diesel 2019-2020 Specifications Specification Detail Part Number 68157291AA + 68436631AA / FJ-31AA-91AA Front Filter 68157291AA — 3 Micron, Water Separating Rear Filter 68436631AA — 3 Micron CP4.2 Protection Critical The Bosch CP4.2 pump operates at 29,000 PSI with micron-level clearances. Contaminated fuel can cause self-destruction, sending metal debris through the entire fuel system—a repair exceeding $10,000. Regular filter changes at 15,000-mile intervals are your best defense. Frequently Asked Questions Q: Does this kit include both filters?A: Yes. Both 68157291AA (front chassis) AND 68436631AA (rear engine bay) are included. Q: Which filter goes where?A: 68157291AA is the larger canister under the driver-side frame rail. 68436631AA is the cartridge in the passenger-side engine bay. Q: Work on 2021 Ram?A: No. 2021+ uses a different fuel filter system. This kit is for 2019-2020 models only. Q: Change interval?A: Every 15,000 miles or 12 months. Heavy towing or commercial use: every 10,000 miles. Q: Genuine Mopar?A: Premium aftermarket manufactured in ISO 9001 facilities to meet or exceed Mopar specs at significant savings. Related Ram Cummins Products 68157291AA Single Fuel Filter 68157291AA + Black Housing Cap Helpful Articles iFJF Blog — Ram Cummins Maintenance

Read more less

Complete fuel filter kit for Ram 6.7L Cummins diesel trucks (2011-2020). Includes OEM-spec 68157291AA filter element AND 68065612AA black billet aluminum housing cap. Direct fit for 2500, 3500, 4500, 5500 models. Superior filtration protects your CP4/CP3 injection pump.How to install: Ram 6.7L Cummins: Change BOTH Fuel Filters — Step-by-Step

Read more less

68157291AA Fuel Filter + Silver Canister Housing Cap — Ram 6.7L Cummins Do not let a $25 plastic cap cost you thousands in fuel system repairs. The iFJF 68157291AA Fuel Filter + Silver Aluminum Housing Cap Combo permanently solves the notorious Ram plastic cap problem while providing OEM-grade 3-micron fuel filtration for your 2011-2020 Ram 2500/3500 6.7L Cummins. The silver anodized billet aluminum cap (replaces 68065612AA) is CNC-machined for perfect fit and features a brilliant silver finish that resists corrosion through years of filter changes. Key Features Complete Kit: 68157291AA filter + 68065612AA silver aluminum cap + new O-ring—everything in one box Billet Aluminum Cap — Silver: 6061-T6 aircraft-grade aluminum with clear anodized finish for maximum corrosion resistance 3-Micron Filtration: Captures 99.9% of particles 3 microns and larger—critical CP3/CP4 protection Water-Separating Media: Hydrophobic filter element removes water before it damages injectors Precision Hex Drive: Identical hex size to factory cap (1-1/4 inch or 32mm) for existing tool compatibility Compatibility Vehicle Engine Years Ram 2500 6.7L Cummins Turbo Diesel 2011-2020 Ram 3500 6.7L Cummins Turbo Diesel 2011-2020 Ram 4500/5500 6.7L Cummins Turbo Diesel 2011-2020 Specifications Specification Detail Part Number FJ-91AA-CAP01-RD Filter 68157291AA — 3 Micron, Water Separating Cap 68065612AA Replacement — Billet Aluminum, Silver Cap Material 6061-T6 Aluminum, Clear Anodized Installation Tips Place drain pan under chassis-mounted filter housing (driver-side frame rail) Open water drain valve (yellow lever) to drain housing Use 1-1/4 inch socket or 32mm wrench to unscrew old plastic cap Remove old filter element and discard Clean housing interior with lint-free cloth Insert new 68157291AA filter element Lubricate O-ring with clean diesel fuel Install new aluminum cap—hand-tighten then 1/4 turn (18-22 ft-lbs) Cycle key to Run (without starting) 3 times to prime Start engine and check for leaks Frequently Asked Questions Q: Difference between silver and black cap?A: Mechanically identical. Same billet 6061-T6 aluminum, same OEM-spec dimensions. Difference is cosmetic: silver (clear anodized) vs black (hard anodized). Q: Will this fit my 2013 Ram 3500 dually?A: Yes. All 2011-2020 Ram 2500/3500 with 6.7L Cummins use the same front fuel filter housing, including dually configurations. Q: Signs my old cap is bad?A: Fuel weeping around cap threads, stripped hex, visible cracks at O-ring groove, or air in fuel system causing extended cranking. Q: Buy cap without filter?A: This listing includes both. For cap only, search 68065612AA on our store. Q: Does silver anodizing hold up to diesel?A: Yes. MIL-A-8625 Type II anodized finish is chemically resistant to diesel, DEF, and engine bay chemicals. Related Products Same Kit — Black Cap Version 68157291AA + 68436631AA Two-Filter Kit Helpful Articles iFJF Blog — Diesel Fuel System Maintenance

Read more less

68157291AA Fuel Filter — Ram 6.7L Cummins (2010-2020) Your Ram's high-pressure common rail injection system demands clean fuel—period. The iFJF 68157291AA Fuel Filter delivers 3-micron absolute filtration and water separation for the 2010-2020 Ram 2500, 3500, 4500, and 5500 with the legendary 6.7L Cummins turbo diesel. This is the front chassis-mounted filter located under the driver-side frame rail—the first line of defense against fuel contamination. Replaces Mopar 68157291AA and 68436631AA with equivalent performance at aftermarket pricing. Key Features 3-Micron Absolute Filtration: Removes over 99.9% of particles 3 microns and larger—protecting injectors from abrasive wear Water Separation Technology: Hydrophobic media coalesces and separates water from diesel fuel, preventing injector tip erosion High Dirt-Holding Capacity: Extended pleat pack design means longer service intervals and better value versus budget filters OEM-Equivalent Construction: Nitrile O-ring, heavy-gauge steel end caps, and anti-drainback valve match factory specifications Broad Compatibility: Fits 2010-2020 model years—covering both CP3 and CP4.2 injection pump applications Compatibility Vehicle Engine Years Ram 2500 6.7L Cummins I6 Turbo Diesel 2010-2020 Ram 3500 6.7L Cummins I6 Turbo Diesel 2010-2020 Ram 4500/5500 6.7L Cummins I6 Turbo Diesel 2010-2020 Cross-Reference: Mopar 68157291AA, 68436631AA, 68065608AA | Fleetguard PF46152 | WIX WF10255 Specifications Specification Detail Part Number 68157291AA / FJ-91AA-1 Filter Type Canister-Style Fuel/Water Separator Filtration Rating 3 Micron Absolute Water Separation Greater than 95% Efficiency Fuel Compatibility ULSD, B5-B20 Biodiesel The Real Cost of Skipping Fuel Filter Changes The Bosch CP3 (2010-2018) and CP4.2 (2019-2020) injection pumps operate at pressures up to 29,000 PSI with internal clearances measured in microns. A single tank of contaminated fuel can cause cavitation damage leading to pump failure—a repair costing $4,000-$12,000. At under $20, regular filter changes are the cheapest insurance for your truck. Frequently Asked Questions Q: Will this fit my 2015 Ram 2500?A: Yes. Fits all 2010-2020 Ram 2500/3500 with 6.7L Cummins. Q: Front or rear filter?A: Front chassis-mounted filter under driver-side frame rail. Rear engine-bay filter is 68436631AA. Q: How often to change?A: Every 15,000 miles or 12 months. Heavy towing or frequent idling: every 10,000 miles. Q: Includes housing cap?A: No. Filter element only. For cap upgrades, see our aluminum cap combo kits. Q: B20 biodiesel compatible?A: Yes, up to B20. If switching from petroleum diesel, change filter after first tank of B20. Related Ram Cummins Products 68157291AA + 68436631AA Two-Filter Kit 68157291AA + Black Aluminum Cap 68157291AA + Silver Aluminum Cap Helpful Articles iFJF Blog — Cummins Diesel Maintenance Guides

Read more less

68197867AA Fuel Filter Base Conversion Adapter — Ram 6.7L Cummins (2013-2018) Tired of wrestling with the factory cartridge-style fuel filter on your 2013-2018 Ram 6.7L Cummins? The iFJF 68197867AA Fuel Filter Base Conversion Adapter lets you permanently switch to the vastly superior 1R-0750 spin-on filter—a popular upgrade in the Cummins community for better filtration, easier changes, and lower long-term costs. CNC-machined from billet 6061-T6 aluminum, this adapter threads into your existing filter base and accepts the Caterpillar 1R-0750 or equivalent spin-on fuel filter—renowned for 2-micron absolute filtration and massive dirt-holding capacity. Key Features Spin-On Conversion: Upgrade from messy cartridge changes to clean, tool-free spin-on filter replacements 1R-0750 Compatibility: Opens access to Caterpillar 1R-0750 filter (2-micron absolute) and widely available equivalents Billet Aluminum Construction: CNC-machined 6061-T6 with anodized finish—far more durable than factory plastic housing Improved Filtration: 2-micron absolute vs factory 3-micron—better injection system protection Cost Savings: 1R-0750 filters are 30-40% less than factory cartridge—adapter pays for itself in 3-4 changes Compatibility Vehicle Engine Years Ram 2500 6.7L Cummins Turbo Diesel 2013-2018 Ram 3500 6.7L Cummins Turbo Diesel 2013-2018 Ram 4500/5500 6.7L Cummins Turbo Diesel 2013-2018 Accepts Filter: Caterpillar 1R-0750, Fleetguard FS19856, Baldwin BF46071, WIX 33585, Donaldson P553191 Specifications Specification Detail Part Number 68197867AA / FJ-67AA-AT Material 6061-T6 Billet Aluminum Finish Clear Anodized Thread (Base) 1-14 UNS Thread (Filter) 1-14 UNS (1R-0750 Standard) Frequently Asked Questions Q: Will this fit my 2016 Ram 3500?A: Yes. Fits 2013-2018 Ram 2500/3500/4500/5500 with 6.7L Cummins. Q: Includes 1R-0750 filter?A: No. Adapter only. Compatible filters include 1R-0750, FS19856, BF46071, WIX 33585. Q: Will this cause check engine light?A: No. Mechanical component only. No sensors or electronics affected. Q: Reversible?A: Yes. Unthread adapter to return to stock cartridge system. Q: Advantage of 2-micron vs 3-micron?A: Removes particles 33% smaller for extra CP4.2 injection pump protection. Related Fuel System Products 68157291AA Fuel Filter (Stock Replacement) 68157291AA + Black Aluminum Cap Helpful Articles iFJF Blog — Cummins Performance Upgrades

Read more less

Product Overview The 68197867AA Fuel Water Separator Filter is the primary frame-rail mounted diesel fuel filter for 2013-2018 Ram 2500/3500/4500/5500 trucks with the 6.7L Cummins turbo diesel. Located on the driver's side frame rail, this filter is the first line of defense for your CP4.2 high-pressure fuel pump — capturing water, dirt, and debris before they damage expensive injection system components. Compatibility Year Make Model Engine 2013-2018 Ram 2500 6.7L Cummins Diesel 2013-2018 Ram 3500 6.7L Cummins Diesel 2013-2018 Ram 4500 6.7L Cummins Diesel 2013-2018 Ram 5500 6.7L Cummins Diesel Specifications Spec Detail Mopar OE 68197867AA, 68197867AB Cross Ref FS20089, BF46031, P551833, FF1279, LFF5106, PS11937, WF10112 Filter Type Primary Fuel/Water Separator (Frame-Mounted) Filtration 10 Micron Nominal Key Features OEM-Grade Filtration: Engineered to meet or exceed Mopar 68197867AA specifications for fit, form, and function. Water Separation: Proprietary media blend separates free and emulsified water from diesel — critical for CP4.2 pump protection. Complete Kit: Includes both housing O-rings for a proper seal during replacement. 10-Micron Rating: Captures harmful particulate while maintaining fuel flow for full engine power. Why Choose iFJF The CP4.2 injection pump is extremely sensitive to fuel contamination. A failed fuel filter can lead to a $8,000-12,000 repair. iFJF's 68197867AA filter provides OEM-equivalent protection at a lower cost. Every batch is tested for filtration efficiency and water separation performance. Frequently Asked Questions Q: Where is this filter located on my Ram?A: Driver's side frame rail, approximately under the driver's door. Your truck also has a secondary filter under the hood. Q: How often should I replace it?A: Every 15,000 miles or 12 months. Every 10,000 miles if towing heavy or fueling at questionable stations. Q: Does this include O-rings?A: Yes — 2 new O-rings for the housing seal, critical for preventing air intrusion. Q: 68197867AA vs 68197867AB?A: Functionally identical and interchangeable. This filter replaces both.

Read more less

68229402AA Engine Oil Filter — Ram 1500 and Jeep Grand Cherokee 3.0L EcoDiesel Turbocharged diesel engines run hot and are tough on oil. The iFJF 68229402AA Engine Oil Filter provides factory-spec filtration for the 3.0L V6 EcoDiesel (EXF engine) found in 2014-2019 Ram 1500 and 2014-2020 Jeep Grand Cherokee. This high-efficiency cartridge filter replaces Mopar part numbers 68229402AA and 68109834AA. Also cross-references to WIX WF10245. Key Features Synthetic-Blend Media: Advanced filtration provides consistent oil flow across full service interval while trapping particles to 25 microns High-Temperature Rated: Engineered for elevated oil temperatures of turbocharged diesels—no media breakdown, no bypass Anti-Drainback Protection: Integrated silicone anti-drainback valve prevents dry starts by keeping oil in the filter OEM-Exact Fit: Precision-molded cartridge ensures perfect seal in oil filter housing—no bypass, no leaks Complete Kit: Includes new O-ring seals for filter cap and housing—replace both with every oil change Compatibility Vehicle Engine Years Ram 1500 3.0L V6 EcoDiesel (EXF) 2014-2019 Jeep Grand Cherokee 3.0L V6 EcoDiesel (EXF) 2014-2020 Specifications Specification Detail Part Number 68229402AA / FJ-02AA Replaces 68229402AA, 68109834AA, WF10245 Filter Type Cartridge (Housing-Style) Filtration 25 Micron Nominal Oil Spec 5W-40 Full Synthetic Diesel (10.5 qt) Frequently Asked Questions Q: Will this fit my 2016 Ram EcoDiesel?A: Yes. Correct oil filter for all 2014-2019 Ram 1500 with 3.0L V6 EcoDiesel. Q: Includes O-rings?A: Yes. Kit includes filter cap O-ring and housing seals for complete installation. Q: Same as Mopar dealer filter?A: Premium aftermarket equivalent meeting or exceeding Mopar specs at lower price. Q: What oil should I use?A: 5W-40 full synthetic diesel oil meeting Chrysler MS-10902 or ACEA C3. Popular: Rotella T6, Mobil 1 ESP. Q: Can I use on 2020+ EcoDiesel Gen 3?A: No. 2020+ Ram uses Gen 3 EcoDiesel with different filter. This is for Gen 2 (2014-2019). Related EcoDiesel Products 68235275AA Fuel Filter + Wrench Kit 68235275AA + 68229402AA Fuel and Oil Combo Helpful Articles iFJF Blog — EcoDiesel Maintenance Tips

Read more less

68235275AA Fuel Filter + 68229402AA Oil Filter Combo — Ram 1500 EcoDiesel Service Pack Knock out your Ram EcoDiesel's complete filter service in one order. The iFJF 68235275AA Fuel Filter + 68229402AA Oil Filter Combo Pack includes both filters needed for a full 10,000-mile service on the 2014-2019 Ram 1500 3.0L V6 EcoDiesel—at a 25% discount versus buying individually. Also fits the 2014-2020 Jeep Grand Cherokee EcoDiesel, which uses the same engine and filters. What is Included 68235275AA Fuel Filter: 10-micron water-separating cartridge with O-ring kit—protects high-pressure fuel pump 68229402AA Oil Filter: Synthetic-blend cartridge with O-ring kit—rated for full 10,000-mile intervals Key Features Complete Service Pack: Both filters in one box—fuel + oil, everything you need 25% Bundle Savings: Significant discount vs buying individually—makes routine maintenance more affordable OEM-Spec Performance: Both filters meet or exceed Mopar specifications for EXF EcoDiesel engine O-Rings Included: Fresh seals for both housings—critical for preventing leaks and air intrusion One-Click Purchase: No need to search separate part numbers—one order covers entire filter service Compatibility Vehicle Engine Years Ram 1500 3.0L V6 EcoDiesel (EXF) 2014-2019 Jeep Grand Cherokee 3.0L V6 EcoDiesel (EXF) 2014-2020 Specifications Specification Detail Part Number FJ-75AA-02AA Fuel Filter 68235275AA — 10 Micron, Water Separating Oil Filter 68229402AA — 25 Micron, Synthetic Blend Service Interval 10,000 Miles / 12 Months EcoDiesel Maintenance Schedule Service Item Interval Notes Oil and Filter 10,000 mi / 12 mo 5W-40 full synthetic diesel (10.5 qt) Fuel Filter 20,000 mi / 24 mo More often in dusty or poor fuel areas Air Filter 30,000 mi Inspect every oil change DEF Refill ~10,000 mi Approximately 8 gallons per service Frequently Asked Questions Q: Does this combo fit my 2018 Ram EcoDiesel?A: Yes. Both filters are correct for all 2014-2019 Ram 1500 3.0L V6 EcoDiesel (EXF). Q: How much do I save?A: Approximately 25% vs buying fuel and oil filters individually. That is like getting one filter almost free. Q: Both filters include O-rings?A: Yes. Each filter includes necessary O-rings for the respective housing cap. Q: Fits 2020 Ram EcoDiesel?A: 2020 Ram uses Gen 3 EcoDiesel with different filters. This combo is for Gen 2 (2014-2019 Ram, 2014-2020 Grand Cherokee). Q: Change both filters at every service?A: Ram recommends fuel filter every other oil change (20,000 miles). Many owners prefer changing both for simplicity and as cheap insurance. Related Products 68235275AA Fuel Filter + 61150 Wrench Kit 68229402AA Oil Filter (Single) Helpful Articles iFJF Blog — EcoDiesel Service and Maintenance

Read more less

68235275AA Fuel Filter + 61150 Wrench Kit — Ram 1500 EcoDiesel Service Combo Everything you need for a clean, frustration-free fuel filter change on your 2014-2019 Ram 1500 3.0L EcoDiesel—in one package. The iFJF 68235275AA Fuel Filter + 61150 Wrench Combo Kit includes the correct OEM-spec fuel filter cartridge plus our popular billet aluminum housing wrench. When you buy the kit, you save 20% versus purchasing separately—and avoid the headache of a cracked filter cap from using wrong tools. What is Included 68235275AA Fuel Filter: OEM-equivalent cartridge with 10-micron filtration and water-separating media. Includes new O-rings. 61150 Aluminum Filter Wrench: CNC-machined billet aluminum wrench that perfectly engages EcoDiesel hex filter cap. Key Features Complete Service Kit: Filter + wrench—walk out to your truck and get the job done, no extra trips to parts store OEM-Spec Filtration: 10-micron filter with water-separation protects high-pressure pump and piezo injectors Billet Wrench Protection: 61150 wrench eliminates the number one cause of EcoDiesel filter cap failure Kit Savings: 20% off combined price—the wrench practically pays for itself on first filter change Includes O-Rings: Cap O-ring and housing seal included—replace every filter change for reliability Compatibility Vehicle Engine Years Ram 1500 3.0L V6 EcoDiesel (EXF) 2014-2019 Specifications Specification Detail Part Number FJ-75AA-CAP06 Filter 68235275AA — 10 Micron Cartridge Wrench 61150 — Billet Aluminum, 3/8 inch Drive DIY Filter Change Steps Locate fuel filter housing on passenger side of engine bay Place rags under housing—some diesel will spill Open water drain (white knob) to drain housing Use 61150 wrench with 3/8 inch ratchet to unscrew cap Pull out old filter, replace both O-rings Insert new 68235275AA filter, ensure it clicks into cap Hand-tighten cap, then 1/4 turn with wrench Cycle ignition to Run (without starting) 10-15 times to prime Start engine and check for leaks Frequently Asked Questions Q: Does this fit my 2017 Ram EcoDiesel?A: Yes. Both filter and wrench fit all 2014-2019 Ram 1500 3.0L EcoDiesel models. Q: Same filters the dealer uses?A: Premium aftermarket equivalent meeting or exceeding Mopar 68235275AA specifications. Q: How to prime after changing?A: Cycle ignition from OFF to RUN (do not start) 10-15 times. Each cycle runs in-tank lift pump for 2 seconds. Q: Fits Jeep Grand Cherokee EcoDiesel?A: Yes. 2014-2019 Grand Cherokee uses same 3.0L EcoDiesel and same 68235275AA filter. Q: Why replace O-rings every time?A: O-rings take compression set and can develop micro-cracks causing air intrusion, hard starts, and no-start conditions. Related Products 68229402AA Oil Filter for EcoDiesel 68235275AA + 68229402AA Fuel and Oil Combo Helpful Articles iFJF Blog — Ram EcoDiesel DIY Guides

Read more less

68235275AA Fuel Filter for 2014-2019 Ram 1500 3.0L V6 EcoDiesel This 68235275AA fuel filter is precision-engineered for 2014-2019 Ram 1500 equipped with the 3.0L V6 EcoDiesel engine. The 10-micron filtration media captures harmful contaminants — including water, rust particles, and fine sediment — before they can damage your high-pressure fuel injection system. Key Features 10-Micron Filtration: Removes 99%+ of particles ≥10 microns, protecting sensitive injectors and high-pressure pump from premature wear. OEM-Spec Construction: Manufactured to meet or exceed factory specifications for filtration capacity, flow rate, and burst pressure. Multi-Layer Media: High-capacity cellulose/synthetic blend provides superior dirt-holding capacity while maintaining optimal fuel flow under all conditions. Water Separation: Hydrophobic barrier repels emulsified water droplets, protecting fuel system from corrosion and microbial growth. Complete Interchange: Direct replacement for WF10245, PGF412, GF5275, XF10321, PF-4500 and other aftermarket equivalents. Compatibility Table Year Make Model Engine 2014-2019 Ram 1500 3.0L V6 EcoDiesel Technical Specifications Specification Value Part Number 68235275AA Filtration Rating 10 Micron Filter Type Cartridge-style element Interchange Numbers WF10245, PGF412, GF5275, XF10321, PF-4500 Replacement Interval Every 15,000-20,000 miles or 12 months Why Choose iFJF? The EcoDiesel CP4.2 pump operates at up to 29,000 PSI — clean fuel is absolutely critical. A single tank of contaminated diesel can destroy this $2,500+ pump. Our filter provides dealership-grade protection at a fraction of the cost, backed by a 12-month satisfaction guarantee. Regular fuel filter replacement is the single most cost-effective maintenance for your EcoDiesel. Frequently Asked Questions Q: Will this fit my 2014-2019 Ram 1500?A: Yes. This filter is an exact-fit replacement for all 2014-2019 Ram 1500 models with the 3.0L V6 EcoDiesel engine. Q: How often should I replace this filter?A: Every 15,000-20,000 miles or 12 months. Reduce to 7,500-10,000 miles for severe service or biodiesel use. Q: Is this equivalent to the OEM/dealership part?A: Yes. Our aftermarket filter meets or exceeds OEM filtration and flow specifications at a significantly lower price point. Q: Do I need any special tools?A: A socket wrench (typically 28mm or 1-1/8") for the filter housing cap and a drain pan for residual fuel are all you need. Q: What happens if I skip filter changes?A: A clogged filter restricts fuel flow, causing hard starts, power loss, and reduced fuel economy. In extreme cases, contaminants can damage the injection system — repairs exceeding $5,000+.

Read more less

Aluminum Fuel Filter Housing Base for 2013-2018 Ram 6.7L Cummins Replace your cracked or leaking OEM plastic fuel filter housing with this premium aluminum filter base. Designed as a direct bolt-on replacement for 2013-2018 Ram 2500, 3500, 4500, and 5500 equipped with the 6.7L Cummins Turbo Diesel. Specifically engineered for Mopar 68197867AA water separator applications. Why Upgrade to Aluminum? Eliminates Plastic Housing Failure: OEM plastic base is prone to cracking at mounting points — especially in cold climates. CNC-machined aluminum solves this permanently. Integrated Heating Element Provision: Pre-drilled to accept factory heating sheet — maintains fuel temperature for cold-weather starting. Corrosion-Resistant: Anodized aluminum withstands road salt, diesel, and DEF exposure without degradation. Perfect Port Alignment: All ports, sensor bungs, and mounting bosses machined to exact OEM specs — no adapters, no leaks. Compatibility Table Year Make Model Engine 2013-2018 Ram 2500 6.7L Cummins 2013-2018 Ram 3500 6.7L Cummins 2013-2018 Ram 4500 6.7L Cummins 2013-2018 Ram 5500 6.7L Cummins Technical Specifications Specification Value Mopar Reference 68197867AA, 68268285AC Material 6061-T6 Billet Aluminum, Anodized Port Size M14 x 1.5 (OEM quick-connect compatible) Heater Provision Yes — accepts factory heating sheet WIF Sensor Port Yes — accepts 68197867AA sensor Installation Overview Remove old housing (3 bolts), disconnect fuel lines. Transfer heating element and WIF sensor from old housing to new aluminum base. Torque mounting bolts to 18 ft-lbs. Apply clean diesel to O-ring seals. Prime fuel system by cycling key to "Run" 5-6 times. Check for leaks after startup. Frequently Asked Questions Q: Will this fit my 2015 Ram 3500?A: Yes. Designed for all 2013-2018 Ram 2500/3500/4500/5500 with 6.7L Cummins. Q: Does this include the heating element?A: No. Transfer your existing heating sheet from the old housing. Mounting provisions are pre-drilled. Q: Will aluminum prevent the cracking problem?A: Absolutely. The billet aluminum replacement eliminates the plastic cracking issue permanently. Q: What filter cartridge does this use?A: Standard Mopar 68157291AA or 68436631AA fuel filter cartridge — same as OEM. Q: Is professional installation required?A: DIY-capable in 30-60 minutes. Professional recommended if not comfortable with fuel work. Q: Works with aftermarket lift pump?A: Yes. Verify lift pump output does not exceed 15 PSI for optimal performance.

Read more less

Overview The iFJF 68268285AC Fuel Water Separator Assembly is a direct OEM-grade replacement for the chassis-mounted fuel filter housing on 2013-2018 Ram 2500, 3500, 4500, and 5500 trucks equipped with the 6.7L Cummins Turbo Diesel engine. This complete assembly includes the integrated primer pump, water-in-fuel (WIF) sensor connector, drain valve, and mounting bracket — everything you need for a drop-in replacement. Water contamination is the #1 cause of premature injector failure in modern diesel engines. The high-pressure CP4.2 injection pump and piezo injectors in the 6.7L Cummins have extremely tight clearances — even a few drops of water passing through can cause catastrophic damage ($4,000-$8,000 repair cost). This separator assembly ensures reliable water separation and fuel filtration at every fill-up. Key Features Complete Assembly — Includes filter housing, primer pump, WIF sensor port, drain valve, and mounting bracket — pre-assembled OEM-Grade Construction — Manufactured to OE specifications with high-grade composite materials resistant to diesel fuel and biodiesel blends Integrated Primer Pump — Makes fuel system priming after filter changes fast and tool-free — no more cranking the starter WIF Sensor Port — Direct plug-and-play with factory water-in-fuel sensor for dashboard water detection warning Easy Drain Valve — Accessible drain port allows quick water purging during routine maintenance without removing the filter Protects $4,000+ Fuel System — Effective water separation prevents catastrophic CP4.2 pump and injector failure Direct Cross-Reference — Replaces Mopar 68268285AC, 68197866AA, 68197866AB, 68197866AC, 68268285AB Chassis-Mounted Design — Factory-correct location under driver-side frame rail for easy access during oil changes Technical Specifications Specification Details Part Number 68268285AC (Replaces 68197866AA/AB/AC, 68268285AB) Vehicle Fitment 2013-2018 Ram 2500/3500/4500/5500 6.7L Cummins Filter Type Fuel Water Separator Assembly (Chassis-Mounted) Includes Filter Housing, Primer Pump, WIF Sensor Port, Drain Valve, Bracket Material High-Grade Composite / Aluminum Bracket Compatibility Year Make Model Engine 2013-2018 Ram 2500 / 3500 6.7L Cummins I6 Turbo Diesel 2013-2018 Ram 4500 / 5500 (Chassis Cab) 6.7L Cummins I6 Turbo Diesel Installation Guide Relieve Fuel Pressure — Open the fuel filler cap to release tank pressure Locate Assembly — Chassis-mounted housing on the driver-side frame rail, near the fuel tank Disconnect Quick-Connect Lines — Use fuel line disconnect tool; have rags ready for fuel spillage Unplug WIF Sensor — Disconnect the electrical connector from the water-in-fuel sensor Remove Mounting Bolts — Typically 2-3 bolts securing the housing bracket to the frame Install New Assembly — Bolt in the iFJF replacement, reconnect lines and WIF sensor Prime System — Pump the integrated primer until firm resistance is felt Cycle Key & Start — Cycle key to "Run" (not start) 3 times to prime, then start and inspect for leaks Why Replace Your Water Separator? Prevent $4,000-$8,000 Injector Failure: The CP4.2 high-pressure pump and Bosch piezo injectors are extremely sensitive to water. A cracked housing or leaking primer pump compromises water separation — allowing water to reach the injection system. Replacement is far cheaper than injector/pump repair. Stop Diesel Leaks: Cracked filter housings and degraded seals create a fire hazard and fail DOT inspections. A complete assembly replaces all wear-prone components in one service. Restore Reliable Priming: A worn primer pump that won't build pressure makes every filter change a frustrating battle with air-locked fuel lines. FAQ Q: How often should the water separator assembly be replaced?A: The filter element inside the housing should be replaced every 15,000-30,000 miles. The complete housing assembly typically lasts the life of the vehicle unless damaged. Replace the housing if you notice fuel leaks, primer pump failure, or a cracked housing body. Q: Does this include the actual fuel filter element?A: No. This is the housing assembly. You will need to transfer your existing filter element or install a new one. Compatible filter elements include Mopar 68157291AA and aftermarket equivalents. Q: Will this fit my 2019+ Ram with the 6.7L Cummins?A: No. 2019+ Ram HD trucks (5th Gen) use a different fuel filter housing design. This assembly is specifically for 2013-2018 model years. Verify your OEM part number before ordering. Q: Why does my Ram have TWO fuel filters?A: The 6.7L Cummins uses a two-stage filtration system: (1) this chassis-mounted water separator removes water and large particles, then (2) the engine-mounted fuel filter provides final fine filtration before the high-pressure CP4.2 pump. Q: How do I know if my housing is cracked?A: Look for diesel fuel drips or wetness on the housing body, a strong diesel smell near the driver-side frame rail, or difficult priming after filter changes. Cracked housings are common in cold climates where trapped water freezes and expands. Q: Can I drain water without removing the filter?A: Yes! The integrated drain valve on the bottom allows quick water purging. Place a catch container underneath, open the valve, and drain until clean fuel appears. Do this every oil change or whenever the WIF dashboard light illuminates. Q: Is this compatible with B20 biodiesel?A: This housing is manufactured from biodiesel-resistant composite materials rated for B5-B20 blends. Follow your engine manufacturer's biodiesel usage guidelines and reduced filter change intervals when running biodiesel. Q: How does this compare to the OEM Mopar assembly?A: Manufactured to OE specifications using equivalent materials and processes. Same fit, function, and durability at a significantly lower price point. All mounting points, line connections, and sensor ports match factory dimensions exactly. 📚 Related Guides & Articles iFJF Guides & Resources — Expert Tips, Installation Tutorials & Buying Guides

Read more less

68394482AA Fuel Filter for 2014-2018 Ram 1500 3.0L V6 EcoDiesel This 68394482AA fuel filter is precision-engineered for 2014-2018 Ram 1500 equipped with the 3.0L V6 EcoDiesel engine. The 10-micron filtration media captures harmful contaminants — including water, rust particles, and fine sediment — before they can damage your high-pressure fuel injection system. Key Features 10-Micron Filtration: Removes 99%+ of particles ≥10 microns, protecting sensitive injectors and high-pressure pump from premature wear. OEM-Spec Construction: Manufactured to meet or exceed factory specifications for filtration capacity, flow rate, and burst pressure. Multi-Layer Media: High-capacity cellulose/synthetic blend provides superior dirt-holding capacity while maintaining optimal fuel flow under all conditions. Water Separation: Hydrophobic barrier repels emulsified water droplets, protecting fuel system from corrosion and microbial growth. Complete Interchange: Direct replacement for 68197368AF, 68197368AC, 68197368AE, 68197368AD and other aftermarket equivalents. Compatibility Table Year Make Model Engine 2014-2018 Ram 1500 3.0L V6 EcoDiesel Technical Specifications Specification Value Part Number 68394482AA Filtration Rating 10 Micron Filter Type Cartridge-style element Interchange Numbers 68197368AF, 68197368AC, 68197368AE, 68197368AD Replacement Interval Every 15,000-20,000 miles or 12 months Why Regular Replacement Matters The EcoDiesel's high-pressure common rail system operates at up to 29,000 PSI. Water contamination is the #1 enemy — causing corrosion, cavitation, and microbial growth. A properly functioning water separator is your first line of defense. Replace at every other oil change to maintain peak protection. Frequently Asked Questions Q: Will this fit my 2014-2018 Ram 1500?A: Yes. This filter is an exact-fit replacement for all 2014-2018 Ram 1500 models with the 3.0L V6 EcoDiesel engine. Q: How often should I replace this filter?A: Every 15,000-20,000 miles or 12 months. Reduce to 7,500-10,000 miles for severe service or biodiesel use. Q: Is this equivalent to the OEM/dealership part?A: Yes. Our aftermarket filter meets or exceeds OEM filtration and flow specifications at a significantly lower price point. Q: Do I need any special tools?A: A socket wrench (typically 28mm or 1-1/8") for the filter housing cap and a drain pan for residual fuel are all you need. Q: What happens if I skip filter changes?A: A clogged filter restricts fuel flow, causing hard starts, power loss, and reduced fuel economy. In extreme cases, contaminants can damage the injection system — repairs exceeding $5,000+.

Read more less

68406048AA Cabin Air Filter for 2011-2020 Ram 1500-5500 — Breathe Cleaner Air Upgrade your Ram truck's cabin air quality with this premium cabin air filter for 2011-2020 Ram 1500, 2500, 3500, 4500, and 5500 models. Direct replacement for Mopar 68406048AA and 5058693AA. Multi-layer filtration with activated carbon captures airborne contaminants that affect your health and comfort — from diesel soot and PM2.5 to pollen, mold spores, and road dust. Compatibility Year Range Make Model Range 2011-2020 Ram 1500, 2500, 3500, 4500, 5500 (All Trims) Fits both 4th Generation (DS/DJ/D2) and 5th Generation (DT) Ram 1500, plus all 2011-2020 Heavy Duty models. Key Features Multi-Layer Filtration Technology: Advanced electrostatic meltblown layer captures particles as small as 0.3 microns — including PM2.5 particulate matter, diesel exhaust soot, brake dust, pollen, and mold spores. Far superior to basic paper filters. Activated Carbon Layer: Embedded carbon granules neutralize odors from diesel exhaust, agricultural chemicals, urban pollution, and musty HVAC system smells. Particularly valuable for truck owners in agricultural, industrial, and high-traffic areas. OEM-Exact Fitment: Precision-cut to factory dimensions — installs in under 5 minutes behind the glove box with zero modifications. No forcing, no trimming, no gaps. Extended Service Life: High-capacity pleated design provides effective filtration up to 15,000-20,000 miles or 12 months, depending on operating environment. Improved HVAC Efficiency: Clean filter maintains maximum airflow through the heating and cooling system, preventing strain on the blower motor and ensuring consistent cabin temperature control. Technical Specifications Part Number 68406048AA, 5058693AA Cross-Reference CF11671 Filter Type Panel-style cabin air filter with activated carbon Location Behind glove box, passenger side dash Replacement Interval Every 15,000-20,000 miles or 12 months (10,000 miles for severe conditions) Filtration Layers Electrostatic meltblown + activated carbon + support scrim Signs Your Cabin Air Filter Needs Replacement Reduced airflow from HVAC vents even at maximum fan speed Musty, stale, or unpleasant odor when using air conditioning or heat Excessive window fogging in humid conditions (clogged filter restricts defrost airflow) Increased allergic reactions, sneezing, or respiratory irritation while driving Visible debris, discoloration, or mold on the filter when inspected Whistling or unusual noise from the HVAC blower motor under load Installation Guide Open Glove Box: Empty the glove box contents. The filter access is behind it. Release Damper Cord: Disconnect the glove box damper cord from the right side of the glove box (gently pull the loop off the hook). Drop Glove Box: Squeeze the sides of the glove box inward to release the stop tabs. Lower the glove box fully — it will hinge downward, revealing the filter access door. Open Filter Door: The cabin filter access door is a rectangular panel. Release the tabs (typically two at the top or bottom) and remove the door. Remove Old Filter: Slide out the old filter. Note the airflow direction arrow printed on the filter frame. Install New Filter: Insert the new 68406048AA filter with the airflow arrow pointing in the correct direction (typically toward the passenger compartment / downward). Reassemble: Replace the filter access door, raise the glove box, reattach the damper cord, and close. FAQ Q: Where is the cabin air filter located in my Ram? A: Behind the glove box on the passenger side. Open the glove box, release the damper cord on the right side, squeeze the sides inward to release the stops, and the filter access door is behind it. Q: How often should I replace the cabin filter? A: Every 15,000-20,000 miles or 12 months under normal conditions. Replace every 10,000 miles if you frequently drive on dirt or gravel roads, in high-pollen areas, or in regions with poor air quality. Q: Will a dirty cabin filter affect my air conditioning? A: Yes — significantly. A clogged filter restricts airflow across the evaporator, reducing cooling capacity and potentially causing the evaporator to freeze up. This can lead to water leaks inside the cabin and expensive A/C repairs. Q: Does this fit the 2019+ Ram 1500 5th Generation? A: Yes. This filter fits both 4th Generation (2011-2018 DS/DJ) and 5th Generation (2019-2020 DT) Ram 1500 models, plus all 2011-2020 Heavy Duty 2500-5500 trucks. Q: How does this compare to the OEM Mopar filter? A: This iFJF filter meets or exceeds OEM filtration specifications with the same multi-layer design and activated carbon layer. Same protection, same fit, significantly better value than the Mopar-branded equivalent. Why Choose iFJF? Premium Filtration at Factory-Direct Prices: Multi-layer carbon filtration that matches or exceeds Mopar OEM specifications — without the dealership parts counter markup. Health-Focused Design: We engineer cabin filters with real-world air quality challenges in mind — diesel soot, agricultural dust, urban pollution. Not just a paper barrier. Easy DIY Installation: Designed for quick homeowner installation. No special tools, no mechanic visit required. 5 minutes from start to finish. US Stock & Fast Delivery: Ships from our US warehouses. Typical delivery: 3-5 business days. Customer Support: Contact support@ifjf.net with any fitment or installation questions. Related Products 68436631AA + 5083285AA Filter Kit — Fuel + oil filter kit for 2019-2020 Ram 6.7L Cummins Billet Aluminum Fuel Cap — Magnetic fuel cap for 2013+ Ram Cummins RCX70101 Pool Filter (4-Pack) — Pool filter cartridges for TigerShark & AquaVac

Read more less