903429 903429A Furnace Control Board for Intertherm M1M — Fits 624602

Description

903429 903429A Furnace Control Board for Intertherm M1M — Fits 624602

The 903429 integrated furnace control board is a direct replacement control for Nordyne-platform M1 series gas furnaces built for manufactured and mobile homes — the Intertherm, Miller, Nordyne, Nortek, Revolv and Broan units that used board number 903429 (later revised to 903429A) or any of the earlier numbers 624602, 6246020, 624602-0, 624602A, 624602B, 624640 and 624640-A. It runs on 120 VAC line power with a 24 VAC thermostat circuit, sequences the inducer, hot surface igniter, gas valve and blower on every call for heat, and reports faults through the on-board red and yellow diagnostic LEDs. The board measures 5 × 1.1 × 5.5 in and weighs 8.8 oz (249 g), so it drops onto the original standoffs inside the M1 furnace control compartment.

📋 Key Takeaways

  • ✅ Direct Replacement: Replaces 903429 and the revised 903429A across Nordyne M1 series gas furnaces.
  • ✅ Full Cross-Reference: Also covers 624602, 6246020, 624602-0, 624602A, 624602B, 624640 and 624640-A.
  • ✅ M1 M Series Coverage: Fits M1MA / M1MB / M1MC / M1MD (056, 070, 077, 090) and M1GB / M1GC / M1GD / M1GH (056, 070, 077, 090) cabinets.
  • ✅ 120 VAC Line / 24 VAC Control: 120 VAC 60 Hz input with an 18–30 VAC thermostat circuit — the same electrical arrangement as the original control.
  • ✅ Hot Surface Ignition: Drives the 6.0 A igniter, proves flame through the flame sensor and holds the gas valve closed (0.5 A @ 24 VAC) when proof is lost.
  • ✅ Red + Yellow LED Diagnostics: Flash codes separate a limit, pressure-switch, flame-sense, ignition-lockout or grounding fault before any part is swapped.
  • ✅ Check Before You Order: Read the number silkscreened on the old board — this is an M1-platform control, not a universal board.

Features & Benefits

Feature Benefit (What It Means for You)
Integrated control (IFC) for M1 furnaces One board runs the whole heating sequence — inducer proof, hot surface igniter warm-up, gas valve timing, blower on delay and cool-down — so the furnace behaves exactly as it did with the factory control.
Replaces 903429 / 903429A, 624602, 624640 family A furnace whose data plate or parts list shows any of those numbers uses this board, which takes the guesswork out of matching an earlier revision to the current one.
120 VAC line, 24 VAC control circuit Standard manufactured-home furnace voltages with the original terminal designations, so the thermostat, gas valve, inducer and blower wires transfer connector by connector without modification.
Hot surface ignition with flame sensing The board heats the igniter, opens the gas valve only after the ignition window, and shuts the valve the moment flame proof is lost — the safety behaviour unburned gas depends on.
Red and yellow diagnostic LEDs A red flash code names the fault the board has latched (limit open, pressure switch, ignition lockout, reversed polarity or bad ground) and the yellow LED shows flame signal strength, so diagnosis starts at the board.
Drop-in mounting on the original standoffs The four white standoffs and the molex / push-on terminal layout match the M1 compartment, so no bracket, drilling or harness adapter is needed.

Compatibility & Cross-Reference

Replaces / Interchange Part Numbers

Interchange Part Number Note
903429 Board number of this replacement (Nordyne / Nortek integrated control, M1 series)
903429A Later revision of 903429 — same form, fit and function
624602 Earlier M1 control number carried on parts lists
6246020 / 624602-0 Variant spellings of the 624602 number
624602A / 624602B Revision letters of the 624602 control
624640 / 624640-A M1 control number used on later production runs

Honeywell-Built OEM Numbers for the Same Board

Nordyne had this control built by Honeywell, so the board also carries Honeywell numbers. They look like different parts but they are the same 1012-958 board written at three levels of detail — the middle segment is a production / revision code, not a different board:

Honeywell Number Note
1012-958 / 1012-958A Short form printed on the board and quoted in Nordyne parts lists
1012-93-9581A Long form: the 93 segment is a revision code, 958 is the board, A the change level
1012-012-958A Long form with a different revision prefix — the 958 board is unchanged
233089 Nordyne internal stocking number for the same control

So a board marked 903429, 903429A, 624602, 624640 or 1012-958A is the same part written differently. If the number on your board is not in either table above, it is a different control and this board will not fit.

Common Applications

  • Nordyne M1M series gas furnaces — M1MA, M1MB, M1MC and M1MD cabinets in 056, 070, 077 and 090 input sizes, for example M1MB 070A BW and M1MC 090A AW
  • Nordyne M1G series gas furnaces — M1GB, M1GC, M1GD and M1GH cabinets in 056, 070, 077 and 090 input sizes
  • Manufactured home, mobile home and park model installations where the furnace sits in a closet or alcove with a roof-jack vent
  • Furnaces sold under the Intertherm, Miller, Nordyne, Nortek, Revolv and Broan names on the same M1 platform

This is a Nordyne M1-platform control, not a universal board. Read the number printed on your old board before ordering: if it matches any number in the table above, this board is the replacement. A board from another manufacturer will not interchange even when the connector count looks similar.

Red & Yellow LED Diagnostic Codes

The board reports through two LEDs. Count the red flashes, then check the yellow LED for flame signal:

LED Indication Meaning
Red Steady ON Control OK — board is powered and the internal check passed
Red Steady OFF No power to the board — check the 120 VAC supply, the furnace switch and the board fuse
Red Rapid flash False flame or internal control fault
Red 1 flash Limit switch is open
Red 2 flashes Pressure switch is open with the inducer running
Red 3 flashes Pressure switch is closed with the inducer off
Red 4 flashes Lockout due to failed ignition
Red 5 flashes 115 VAC line and neutral reversed, or no ground
Yellow Steady ON Good flame signal
Yellow Blinking Weak flame signal — clean or reposition the flame sensor
Yellow Steady OFF No flame signal

Specifications

Part Number 903429 (replaces 903429A)
Control Type Integrated furnace control (IFC), single stage
Furnace Series Nordyne M1 series — M1M and M1G cabinets
Input Power 120 VAC, 60 Hz
Control Voltage 24 VAC thermostat circuit (18–30 VAC)
Ignition Hot surface ignition, 6.0 A @ 120 VAC igniter output
Gas Valve Output 0.5 A @ 24 VAC
Inducer Output 1/100 HP, 0.69 A @ 120 VAC
Blower Output 1/5 HP (or 1/8 HP), 120 VAC
Diagnostics Red flash code + yellow flame signal LED, 3 A on-board fuse
Replaces 903429, 903429A, 624602, 6246020, 624602-0, 624602A, 624602B, 624640, 624640-A
Also Crosses 1012-958, 1012-958A, 1012-93-9581A, 1012-012-958A, 233089 (Honeywell-built OEM numbers)
Dimensions 5 × 1.1 × 5.5 in (127 × 28 × 140 mm)
Net Weight 8.8 oz (249 g)
Package Contents 1 × 903429 integrated furnace control board
Warranty iFJF Quality Guarantee

Installation Tips

  1. Cut power at the furnace switch or breaker and shut off the gas supply. Confirm 0 V at the board with a meter before touching a connector.
  2. Photograph every molex plug and push-on terminal before removal — the M1 compartment is tight and the harness has no spare length.
  3. Squeeze the four white standoffs while lifting the old board off, then press the new board onto the same standoffs from the outside edge only.
  4. Reconnect one plug at a time to the identically marked terminal, restore power and watch one complete heat cycle: inducer, igniter, gas valve, blower.
  5. If the on-board 3 A fuse is blown, replace it with a 3 A fuse (Nordyne G32-189) and find the short before powering the furnace again.
Installation note: a control board swap on a gas furnace should be performed by a qualified HVAC contractor or licensed electrician. If you are unsure whether this board matches your furnace, message us with the model number from the rating plate before ordering.

Need help confirming fitment? Our support team answers fitment questions before you order — support@ifjf.com.

Why Choose iFJF?

  • ✅ Open cross-reference: all nine covered numbers (903429, 903429A, 624602, 6246020, 624602-0, 624602A, 624602B, 624640, 624640-A) are printed above — match the old board first.
  • ✅ Specification transparency: 120 VAC input, 18–30 VAC control circuit, 6.0 A igniter output and 0.5 A gas valve load are stated openly so they can be compared with your original control.
  • ✅ Every board powered up before it ships: each unit is functionally tested for fan control, ignition sequencing and safety interlock.
  • ✅ Factory-direct value: supply straight from the manufacturer, without the OEM dealer-counter markup on a discontinued 903429.

Frequently Asked Questions

Q: Will the 903429 control board fit my furnace?

A: The 903429 board is built for Nordyne M1 series gas furnaces used in manufactured and mobile homes, sold as Intertherm, Miller, Nordyne, Nortek, Revolv and Broan. Read the part number on the old board first: if it is 903429, 903429A, 624602, 6246020, 624602-0, 624602A, 624602B, 624640 or 624640-A, this board is the direct replacement. The cross-reference table above lists every covered number.

Q: Which part numbers does the 903429 board replace?

A: It replaces 903429 and its later revision 903429A, plus the earlier numbers 624602, 6246020, 624602-0, 624602A, 624602B, 624640 and 624640-A. Nordyne discontinued the original 903429 and issued 903429A as the same board under a new number, so a furnace whose parts list shows either number takes this control.

Q: What are the electrical specifications of the 903429 board?

A: The board takes 120 VAC 60 Hz line power and runs an 18-30 VAC thermostat circuit. It drives a hot surface igniter at 6.0 A, a 24 VAC gas valve at 0.5 A, a 1/100 HP inducer at 0.69 A and a 1/5 HP (or 1/8 HP) 120 VAC blower, and it protects the low-voltage side with a 3 A fuse.

Q: How do I read the diagnostic codes on this board?

A: The red LED shows control status: steady ON means the board is good, one flash an open limit, two flashes a pressure switch open with the inducer running, three flashes a pressure switch closed with the inducer off, four flashes an ignition lockout, and five flashes reversed line and neutral or a missing ground. The yellow LED shows flame: steady ON is a good signal, blinking is a weak signal, and OFF means no flame detected.

Q: Is this a genuine Nordyne OEM board?

A: No. This is an iFJF third-party replacement built to the same 120 VAC input, 24 VAC control, hot surface ignition and terminal layout as the original 903429 / 903429A control. It is not sold as a Nordyne or Nortek OEM part, and the price reflects factory-direct supply instead of dealer-counter pricing on a discontinued board.

Q: How do I install the 903429 control board?

A: Cut power at the breaker and shut off the gas, then photograph every molex plug and push-on terminal. Squeeze the four white standoffs to release the old board, press the new board onto the same standoffs, and reconnect one plug at a time to the matching terminal. Restore power and watch a full heat cycle. A qualified HVAC technician should do the work if you are not comfortable inside a gas appliance.

Q: How do I know my old control board is actually the problem?

A: Typical board failures are no ignition, a blower or inducer that runs continuously, a burner that lights and drops out without a pattern, or a red LED that shows a fault code or stays dark. Check the board fuse, the limit and rollout switches, the pressure switch tubing, the flame sensor and the ground first, because a blown fuse or an open limit produces the same no-heat symptom as a failed board.

Which Nordyne Furnace Control Board Do You Need?

Nordyne built several furnace families that look alike but take different controls. Match the model prefix on the rating plate to the board, not the price:

Furnace Family Board Notes
M1 series
M1MA / M1MB / M1MC / M1MD, M1GB / M1GC / M1GD / M1GH
903429 — this listing
$89.99
Manufactured-home downflow gas furnaces that used 903429 / 624602 / 624640 controls
G7 / M7 series
G7SA / G7SK / G7SC / G7SL, M7RL
920915
$79.99
A different single-stage control — will not interchange with an M1 furnace

If your rating plate says M1, the 903429 board in this listing is the one to order. If it says G7 or M7, you need the 920915 board instead — the two controls are not interchangeable.

Package Includes

  • 1 × 903429 integrated furnace control board

Common Problems with M1 Furnace Control Boards — Solved by iFJF

We read verified owner reviews of Nordyne M1 replacement boards. Here is what keeps coming up — and how this board addresses it:

❌ What Owners Complain About ✅ How This Board Addresses It
“It says compatible but my furnace did not work”
— the #1 cause of returns in this category
→ Board number listed before the price
903429, 903429A, 624602 and 624640 are printed in the cross-reference table, so the old board is matched before ordering. This is an M1-platform control, not a universal board.
“The blower runs but there is no heat”
— often a flame-sense or limit fault, not the board
→ LED code before parts
The red LED latches the real fault — limit, pressure switch, ignition lockout or ground — so the fuse, limit and flame sensor are checked before the board is condemned.
“The connectors did not line up with my old board”
— common when a revision is swapped blind
→ Same molex and spade layout
Terminals follow the original 903429 layout and the four white standoffs are in the OEM position, so wiring moves plug by plug from a photographed old board.
“It failed a month after install”
— usually heat, vibration or a shorted low-voltage circuit
→ Power-tested, fused and sealed
Every board runs a functional test of fan control, ignition sequencing and safety interlock before shipping, and the 3 A fuse protects the control side from a shorted thermostat wire.

📦 Related Furnace Control Boards

Each board in the table above fits a different furnace family — the shared 24 VAC single-stage architecture does not make them interchangeable, so confirm the number on your old board before ordering.

📂 Browse More: All Electronics Products →

🔄 Cross Reference

903429 = 903429A = 624602 = 6246020 = 624602-0 = 624602A = 624602B = 624640 = 624640-A. All nine numbers are printed on Nordyne-platform M1 series gas furnaces; the board in this listing replaces every one of them.

Factory Direct Supply & Wholesale — iFJF is a direct manufacturer of high-performance replacement parts for heating and filtration systems. Custom specifications and bulk orders are highly welcome. Contact us for exclusive dealer pricing and volume discounts. Backed by ISO 9001:2015 and IATF 16949:2016 quality management system certifications.
Email: support@ifjf.com

903429 903429A Furnace Control Board for Intertherm M1M — Fits 624602

Product form

SKU: FJ-CB-NOR9034

$89.99

      Description

      903429 903429A Furnace Control Board for Intertherm M1M — Fits 624602

      The 903429 integrated furnace control board is a direct replacement control for Nordyne-platform M1 series gas furnaces built for manufactured and mobile homes — the Intertherm, Miller, Nordyne, Nortek, Revolv and Broan units that used board number 903429 (later revised to 903429A) or any of the earlier numbers 624602, 6246020, 624602-0, 624602A, 624602B, 624640 and 624640-A. It runs on 120 VAC line power with a 24 VAC thermostat circuit, sequences the inducer, hot surface igniter, gas valve and blower on every call for heat, and reports faults through the on-board red and yellow diagnostic LEDs. The board measures 5 × 1.1 × 5.5 in and weighs 8.8 oz (249 g), so it drops onto the original standoffs inside the M1 furnace control compartment.

      📋 Key Takeaways

      • ✅ Direct Replacement: Replaces 903429 and the revised 903429A across Nordyne M1 series gas furnaces.
      • ✅ Full Cross-Reference: Also covers 624602, 6246020, 624602-0, 624602A, 624602B, 624640 and 624640-A.
      • ✅ M1 M Series Coverage: Fits M1MA / M1MB / M1MC / M1MD (056, 070, 077, 090) and M1GB / M1GC / M1GD / M1GH (056, 070, 077, 090) cabinets.
      • ✅ 120 VAC Line / 24 VAC Control: 120 VAC 60 Hz input with an 18–30 VAC thermostat circuit — the same electrical arrangement as the original control.
      • ✅ Hot Surface Ignition: Drives the 6.0 A igniter, proves flame through the flame sensor and holds the gas valve closed (0.5 A @ 24 VAC) when proof is lost.
      • ✅ Red + Yellow LED Diagnostics: Flash codes separate a limit, pressure-switch, flame-sense, ignition-lockout or grounding fault before any part is swapped.
      • ✅ Check Before You Order: Read the number silkscreened on the old board — this is an M1-platform control, not a universal board.

      Features & Benefits

      Feature Benefit (What It Means for You)
      Integrated control (IFC) for M1 furnaces One board runs the whole heating sequence — inducer proof, hot surface igniter warm-up, gas valve timing, blower on delay and cool-down — so the furnace behaves exactly as it did with the factory control.
      Replaces 903429 / 903429A, 624602, 624640 family A furnace whose data plate or parts list shows any of those numbers uses this board, which takes the guesswork out of matching an earlier revision to the current one.
      120 VAC line, 24 VAC control circuit Standard manufactured-home furnace voltages with the original terminal designations, so the thermostat, gas valve, inducer and blower wires transfer connector by connector without modification.
      Hot surface ignition with flame sensing The board heats the igniter, opens the gas valve only after the ignition window, and shuts the valve the moment flame proof is lost — the safety behaviour unburned gas depends on.
      Red and yellow diagnostic LEDs A red flash code names the fault the board has latched (limit open, pressure switch, ignition lockout, reversed polarity or bad ground) and the yellow LED shows flame signal strength, so diagnosis starts at the board.
      Drop-in mounting on the original standoffs The four white standoffs and the molex / push-on terminal layout match the M1 compartment, so no bracket, drilling or harness adapter is needed.

      Compatibility & Cross-Reference

      Replaces / Interchange Part Numbers

      Interchange Part Number Note
      903429 Board number of this replacement (Nordyne / Nortek integrated control, M1 series)
      903429A Later revision of 903429 — same form, fit and function
      624602 Earlier M1 control number carried on parts lists
      6246020 / 624602-0 Variant spellings of the 624602 number
      624602A / 624602B Revision letters of the 624602 control
      624640 / 624640-A M1 control number used on later production runs

      Honeywell-Built OEM Numbers for the Same Board

      Nordyne had this control built by Honeywell, so the board also carries Honeywell numbers. They look like different parts but they are the same 1012-958 board written at three levels of detail — the middle segment is a production / revision code, not a different board:

      Honeywell Number Note
      1012-958 / 1012-958A Short form printed on the board and quoted in Nordyne parts lists
      1012-93-9581A Long form: the 93 segment is a revision code, 958 is the board, A the change level
      1012-012-958A Long form with a different revision prefix — the 958 board is unchanged
      233089 Nordyne internal stocking number for the same control

      So a board marked 903429, 903429A, 624602, 624640 or 1012-958A is the same part written differently. If the number on your board is not in either table above, it is a different control and this board will not fit.

      Common Applications

      • Nordyne M1M series gas furnaces — M1MA, M1MB, M1MC and M1MD cabinets in 056, 070, 077 and 090 input sizes, for example M1MB 070A BW and M1MC 090A AW
      • Nordyne M1G series gas furnaces — M1GB, M1GC, M1GD and M1GH cabinets in 056, 070, 077 and 090 input sizes
      • Manufactured home, mobile home and park model installations where the furnace sits in a closet or alcove with a roof-jack vent
      • Furnaces sold under the Intertherm, Miller, Nordyne, Nortek, Revolv and Broan names on the same M1 platform

      This is a Nordyne M1-platform control, not a universal board. Read the number printed on your old board before ordering: if it matches any number in the table above, this board is the replacement. A board from another manufacturer will not interchange even when the connector count looks similar.

      Red & Yellow LED Diagnostic Codes

      The board reports through two LEDs. Count the red flashes, then check the yellow LED for flame signal:

      LED Indication Meaning
      Red Steady ON Control OK — board is powered and the internal check passed
      Red Steady OFF No power to the board — check the 120 VAC supply, the furnace switch and the board fuse
      Red Rapid flash False flame or internal control fault
      Red 1 flash Limit switch is open
      Red 2 flashes Pressure switch is open with the inducer running
      Red 3 flashes Pressure switch is closed with the inducer off
      Red 4 flashes Lockout due to failed ignition
      Red 5 flashes 115 VAC line and neutral reversed, or no ground
      Yellow Steady ON Good flame signal
      Yellow Blinking Weak flame signal — clean or reposition the flame sensor
      Yellow Steady OFF No flame signal

      Specifications

      Part Number 903429 (replaces 903429A)
      Control Type Integrated furnace control (IFC), single stage
      Furnace Series Nordyne M1 series — M1M and M1G cabinets
      Input Power 120 VAC, 60 Hz
      Control Voltage 24 VAC thermostat circuit (18–30 VAC)
      Ignition Hot surface ignition, 6.0 A @ 120 VAC igniter output
      Gas Valve Output 0.5 A @ 24 VAC
      Inducer Output 1/100 HP, 0.69 A @ 120 VAC
      Blower Output 1/5 HP (or 1/8 HP), 120 VAC
      Diagnostics Red flash code + yellow flame signal LED, 3 A on-board fuse
      Replaces 903429, 903429A, 624602, 6246020, 624602-0, 624602A, 624602B, 624640, 624640-A
      Also Crosses 1012-958, 1012-958A, 1012-93-9581A, 1012-012-958A, 233089 (Honeywell-built OEM numbers)
      Dimensions 5 × 1.1 × 5.5 in (127 × 28 × 140 mm)
      Net Weight 8.8 oz (249 g)
      Package Contents 1 × 903429 integrated furnace control board
      Warranty iFJF Quality Guarantee

      Installation Tips

      1. Cut power at the furnace switch or breaker and shut off the gas supply. Confirm 0 V at the board with a meter before touching a connector.
      2. Photograph every molex plug and push-on terminal before removal — the M1 compartment is tight and the harness has no spare length.
      3. Squeeze the four white standoffs while lifting the old board off, then press the new board onto the same standoffs from the outside edge only.
      4. Reconnect one plug at a time to the identically marked terminal, restore power and watch one complete heat cycle: inducer, igniter, gas valve, blower.
      5. If the on-board 3 A fuse is blown, replace it with a 3 A fuse (Nordyne G32-189) and find the short before powering the furnace again.
      Installation note: a control board swap on a gas furnace should be performed by a qualified HVAC contractor or licensed electrician. If you are unsure whether this board matches your furnace, message us with the model number from the rating plate before ordering.

      Need help confirming fitment? Our support team answers fitment questions before you order — support@ifjf.com.

      Why Choose iFJF?

      • ✅ Open cross-reference: all nine covered numbers (903429, 903429A, 624602, 6246020, 624602-0, 624602A, 624602B, 624640, 624640-A) are printed above — match the old board first.
      • ✅ Specification transparency: 120 VAC input, 18–30 VAC control circuit, 6.0 A igniter output and 0.5 A gas valve load are stated openly so they can be compared with your original control.
      • ✅ Every board powered up before it ships: each unit is functionally tested for fan control, ignition sequencing and safety interlock.
      • ✅ Factory-direct value: supply straight from the manufacturer, without the OEM dealer-counter markup on a discontinued 903429.

      Frequently Asked Questions

      Q: Will the 903429 control board fit my furnace?

      A: The 903429 board is built for Nordyne M1 series gas furnaces used in manufactured and mobile homes, sold as Intertherm, Miller, Nordyne, Nortek, Revolv and Broan. Read the part number on the old board first: if it is 903429, 903429A, 624602, 6246020, 624602-0, 624602A, 624602B, 624640 or 624640-A, this board is the direct replacement. The cross-reference table above lists every covered number.

      Q: Which part numbers does the 903429 board replace?

      A: It replaces 903429 and its later revision 903429A, plus the earlier numbers 624602, 6246020, 624602-0, 624602A, 624602B, 624640 and 624640-A. Nordyne discontinued the original 903429 and issued 903429A as the same board under a new number, so a furnace whose parts list shows either number takes this control.

      Q: What are the electrical specifications of the 903429 board?

      A: The board takes 120 VAC 60 Hz line power and runs an 18-30 VAC thermostat circuit. It drives a hot surface igniter at 6.0 A, a 24 VAC gas valve at 0.5 A, a 1/100 HP inducer at 0.69 A and a 1/5 HP (or 1/8 HP) 120 VAC blower, and it protects the low-voltage side with a 3 A fuse.

      Q: How do I read the diagnostic codes on this board?

      A: The red LED shows control status: steady ON means the board is good, one flash an open limit, two flashes a pressure switch open with the inducer running, three flashes a pressure switch closed with the inducer off, four flashes an ignition lockout, and five flashes reversed line and neutral or a missing ground. The yellow LED shows flame: steady ON is a good signal, blinking is a weak signal, and OFF means no flame detected.

      Q: Is this a genuine Nordyne OEM board?

      A: No. This is an iFJF third-party replacement built to the same 120 VAC input, 24 VAC control, hot surface ignition and terminal layout as the original 903429 / 903429A control. It is not sold as a Nordyne or Nortek OEM part, and the price reflects factory-direct supply instead of dealer-counter pricing on a discontinued board.

      Q: How do I install the 903429 control board?

      A: Cut power at the breaker and shut off the gas, then photograph every molex plug and push-on terminal. Squeeze the four white standoffs to release the old board, press the new board onto the same standoffs, and reconnect one plug at a time to the matching terminal. Restore power and watch a full heat cycle. A qualified HVAC technician should do the work if you are not comfortable inside a gas appliance.

      Q: How do I know my old control board is actually the problem?

      A: Typical board failures are no ignition, a blower or inducer that runs continuously, a burner that lights and drops out without a pattern, or a red LED that shows a fault code or stays dark. Check the board fuse, the limit and rollout switches, the pressure switch tubing, the flame sensor and the ground first, because a blown fuse or an open limit produces the same no-heat symptom as a failed board.

      Which Nordyne Furnace Control Board Do You Need?

      Nordyne built several furnace families that look alike but take different controls. Match the model prefix on the rating plate to the board, not the price:

      Furnace Family Board Notes
      M1 series
      M1MA / M1MB / M1MC / M1MD, M1GB / M1GC / M1GD / M1GH
      903429 — this listing
      $89.99
      Manufactured-home downflow gas furnaces that used 903429 / 624602 / 624640 controls
      G7 / M7 series
      G7SA / G7SK / G7SC / G7SL, M7RL
      920915
      $79.99
      A different single-stage control — will not interchange with an M1 furnace

      If your rating plate says M1, the 903429 board in this listing is the one to order. If it says G7 or M7, you need the 920915 board instead — the two controls are not interchangeable.

      Package Includes

      • 1 × 903429 integrated furnace control board

      Common Problems with M1 Furnace Control Boards — Solved by iFJF

      We read verified owner reviews of Nordyne M1 replacement boards. Here is what keeps coming up — and how this board addresses it:

      ❌ What Owners Complain About ✅ How This Board Addresses It
      “It says compatible but my furnace did not work”
      — the #1 cause of returns in this category
      → Board number listed before the price
      903429, 903429A, 624602 and 624640 are printed in the cross-reference table, so the old board is matched before ordering. This is an M1-platform control, not a universal board.
      “The blower runs but there is no heat”
      — often a flame-sense or limit fault, not the board
      → LED code before parts
      The red LED latches the real fault — limit, pressure switch, ignition lockout or ground — so the fuse, limit and flame sensor are checked before the board is condemned.
      “The connectors did not line up with my old board”
      — common when a revision is swapped blind
      → Same molex and spade layout
      Terminals follow the original 903429 layout and the four white standoffs are in the OEM position, so wiring moves plug by plug from a photographed old board.
      “It failed a month after install”
      — usually heat, vibration or a shorted low-voltage circuit
      → Power-tested, fused and sealed
      Every board runs a functional test of fan control, ignition sequencing and safety interlock before shipping, and the 3 A fuse protects the control side from a shorted thermostat wire.

      📦 Related Furnace Control Boards

      Each board in the table above fits a different furnace family — the shared 24 VAC single-stage architecture does not make them interchangeable, so confirm the number on your old board before ordering.

      📂 Browse More: All Electronics Products →

      🔄 Cross Reference

      903429 = 903429A = 624602 = 6246020 = 624602-0 = 624602A = 624602B = 624640 = 624640-A. All nine numbers are printed on Nordyne-platform M1 series gas furnaces; the board in this listing replaces every one of them.

      Factory Direct Supply & Wholesale — iFJF is a direct manufacturer of high-performance replacement parts for heating and filtration systems. Custom specifications and bulk orders are highly welcome. Contact us for exclusive dealer pricing and volume discounts. Backed by ISO 9001:2015 and IATF 16949:2016 quality management system certifications.
      Email: support@ifjf.com

      Recently viewed products

      © 2026 iFJF Direct | Sitemap

        • American Express
        • Diners Club
        • Discover
        • Maestro
        • Mastercard
        • PayPal
        • Visa

        Login

        Forgot your password?

        Don't have an account yet?
        Create account