Products

iFJF 796184 Carburetor Overhaul Kit + 697014 Air Filter — Briggs & Stratton 11-19HP Is your Briggs & Stratton-powered lawn mower or garden tractor hard to start, surging at idle, or burning too much fuel? Before you blame the engine, give the carburetor a refresh. The iFJF 796184 Carburetor Overhaul Rebuild Kit includes everything you need to restore smooth, reliable performance — plus a bonus 697014 air filter to complete the tune-up. Designed for 11HP to 19HP B&S engines found on Craftsman, Husqvarna, Poulan, and dozens of other brands, this kit is your one-stop solution for a healthier engine. Key Features & Benefits Complete Carburetor Rebuild Kit Includes all critical wear components: gaskets, O-rings, needle valve, float bowl gasket, Welch plugs, and diaphragm. No need to hunt down individual parts — everything arrives in one package, ready for the job. Bonus 697014 Air Filter Included A dirty air filter is one of the top causes of carburetor issues. This kit includes a replacement 697014 air filter, so you can tackle both the fuel and air sides of engine performance in a single service session. Smart maintenance saves time. Broad Compatibility Replaces Briggs & Stratton part numbers: 796184, 698787, 699900, 699521, 792369, 790032. Fits a wide range of 11HP through 19HP engines — check your engine model number before ordering to confirm fitment. Technical Specifications Specification Detail Model iFJF 796184 Kit + 697014 Filter Replaces OEM B&S 796184, 698787, 699900, 699521, 792369, 790032 Air Filter iFJF 697014 (included) Engine Compatibility B&S 11HP-19HP Engines Kit Contents Gaskets, O-Rings, Needle Valve, Diaphragm, Welch Plugs + Air Filter Compatible Brands & Equipment Craftsman Lawn Tractors & Riding Mowers Husqvarna Lawn & Garden Tractors Poulan Pro Riding Mowers Murray Lawn Tractors Toro Lawn Tractors (select models) John Deere L/LA Series (B&S powered) Snapper Rear-Engine Riders MTD Yard Machines Installation Overview Disconnect the spark plug wire for safety. Remove the air filter cover and old air filter. Disconnect the fuel line and remove the carburetor mounting bolts. Carefully disconnect the governor and choke linkages. Disassemble the carburetor, noting the position of gaskets, springs, and the needle valve. Clean all carburetor passages with carburetor cleaner and compressed air. Do not use wire or drills in the small passages. Install new gaskets, O-rings, needle valve, and diaphragm from the kit. Reassemble in reverse order. Install the new 697014 air filter. Reconnect the spark plug wire and start the engine. Adjust idle mixture if needed. Why Choose iFJF? iFJF Direct provides high-quality replacement parts that meet or exceed OEM specifications. Our 796184 kit is manufactured to tight tolerances for proper fit and sealing. Ships from our US warehouse with fast, free delivery on qualifying orders. Your mower deserves the best — give it iFJF. Frequently Asked Questions How do I know if this kit fits my engine? Check the model number stamped on your Briggs & Stratton engine (usually on the valve cover or blower housing). This kit fits engines requiring OEM part numbers 796184, 698787, 699900, 699521, 792369, or 790032 — typically 11HP to 19HP single-cylinder engines on riding mowers and tractors. Does the kit include a new float? No, the float is not included in this rebuild kit. If your float is damaged, saturated, or leaking, it will need to be purchased separately. Can a beginner install this kit? With basic mechanical aptitude and the right tools (socket set, screwdrivers, carburetor cleaner), this is a manageable DIY project. Take photos during disassembly to help with reassembly, and work on a clean, well-lit surface. Allow 1-2 hours for your first time. What symptoms indicate my carburetor needs a rebuild? Common signs include: hard starting (especially when cold), engine surging or hunting at idle, black smoke from the exhaust, poor throttle response, fuel leaking from the carburetor, and the engine stalling under load. If you experience one or more of these, a rebuild kit can often solve the problem without replacing the entire carburetor. Is the air filter pre-oiled? The 697014 air filter is a dry paper element — no oiling required. Simply install it in the air filter housing, ensuring a proper seal against the gasket surface. Related Products iFJF 799727 Carburetor for B&S Intek 14-18HP iFJF 845273 Carburetor for B&S 611477/613477 Series iFJF 699915 Fuel Solenoid Valve B&S

Read more less

Overview The iFJF 799584 Carburetor is a direct-fit replacement for Briggs & Stratton 09P700 series engines found on walk-behind lawn mowers. Precision-calibrated for optimal fuel delivery, this carburetor restores reliable starting, smooth idling, and consistent power for 140cc 550EX, 625EX, and 675EX engines. Pre-adjusted from the factory for true plug-and-play installation — no tuning required. Key Features OEM-Spec Replacement: Manufactured to match Briggs & Stratton 799584 specifications for exact fitment on 09P700 series 140cc engines used across multiple mower brands. Broad Mower Compatibility: Fits Husqvarna LC 121P, Toro 550EX, Troy-Bilt TB110, Craftsman 247.372370, and many other walk-behind mowers using the BS 140cc engine platform. Factory Pre-Calibrated: Fuel mixture and idle settings are pre-adjusted at the factory. Install, add fresh fuel, and start mowing immediately — no carburetor tuning needed. Complete Assembly: Includes all gaskets, float bowl, needle valve, and internal components. Ready to bolt on right out of the box — no parts to transfer. Improved Fuel Economy: Optimized jetting and clean fuel passages ensure efficient combustion and reduced fuel consumption compared to worn-out carburetors. Easy 15-30 Minute Install: Direct bolt-on design with matching throttle and choke linkage points. Requires only basic hand tools — screwdriver set and socket wrench. Compatibility Engine/Brand Model Spec Briggs & Stratton 09P702 550EX 140cc Briggs & Stratton 09P702 625EX 140cc Briggs & Stratton 09P702 675EX 140cc Briggs & Stratton 09P702 725EXi 140cc Husqvarna LC 121P Push Mower Toro 550EX 140cc Mower Troy-Bilt TB110 Push Mower Craftsman 247.372370 Push Mower Specifications Specification Value Part Number 799584 Engine Series Briggs & Stratton 09P700 Engine Displacement 140cc Fuel Type Gasoline (E10 Compatible) Choke Type Auto-Choke (Thermal) SKU FJ-CBRT-584 Why Choose iFJF? At iFJF Direct, we specialize in high-quality replacement parts backed by rigorous quality control. Each carburetor is individually tested for proper float operation and fuel flow before shipping. We stand behind every product with responsive customer support and a satisfaction guarantee. A new carburetor is often more cost-effective than rebuilding a corroded, gummed-up original — and gets your mower running right the first time. Frequently Asked Questions Q: Will this fit my Briggs & Stratton 550EX engine?A: Yes. This carburetor is compatible with all Briggs & Stratton 09P700 series engines, including the 550EX, 625EX, 675EX, and 725EXi 140cc models. Check your engine model number on the valve cover. Q: Does this carburetor come with gaskets?A: Yes. The carburetor arrives as a complete assembly including all necessary gaskets, float bowl, needle valve, and internal components. No parts to transfer from your old carburetor. Q: Do I need to adjust anything after installation?A: This carburetor comes pre-calibrated from the factory. In most cases, no additional adjustment is required. Simply install it, add fresh fuel, and start mowing right away. Q: My mower is hard to start — will a new carburetor fix this?A: Hard starting is one of the most common symptoms of a dirty or failing carburetor. Clogged jets, stuck floats, and deteriorated gaskets are the usual culprits. Replacing with a new 799584 carburetor typically resolves these issues. Q: How long does installation take?A: For most DIYers, installation takes 15-30 minutes. You'll need basic hand tools (screwdriver set, socket wrench) and a clean, well-lit work area. Q: Is this compatible with ethanol-blended fuel (E10)?A: Yes, the carburetor is compatible with E10 fuel. However, we recommend using fuel stabilizer or draining the carburetor if the mower will be stored for more than 30 days, as ethanol can cause varnish buildup in any small engine carburetor. Package Includes 1 x 799584 Carburetor for BS 09P702 550EX 625EX 675EX 140cc Engine | Complete with gaskets & hardware | Product support documentation

Read more less

iFJF 799727 Replacement Carburetor — Briggs & Stratton Intek 14-18HP When your riding mower's carburetor is beyond rebuilding — clogged beyond cleaning, corroded bodies, or warped from ethanol damage — a full replacement is faster, easier, and often more cost-effective than rebuilding. The iFJF 799727 carburetor is a direct bolt-on replacement for Briggs & Stratton Intek engines in the 14HP to 18HP range, pre-adjusted at the factory for reliable out-of-the-box performance. Key Features & Benefits Direct OEM Replacement Engineered to match Briggs & Stratton part numbers 799727, 698620, 791886, 690194, and 499153. No modifications, no adapter plates — unbolt the old carb and bolt this one on. All mounting holes, fuel line connections, and linkage points match the OEM layout exactly. Pre-Adjusted from the Factory Each carburetor is pre-set for the correct air-fuel mixture and idle speed before packaging. In most cases, you can install it and start mowing within the hour. Minor idle-speed fine-tuning may be needed for your specific engine, but major adjustments are rarely required. Complete with Gaskets & Fuel Filter Includes all mounting gaskets and an inline fuel filter — everything you need in one box. The fuel filter catches debris before it reaches your new carburetor, protecting your investment from day one. Technical Specifications Specification Detail Model iFJF 799727 Replaces OEM B&S 799727, 698620, 791886, 690194, 499153, 498061, 695412, 793224, 495935, 498051, 498059, 496796 Engine Family B&S Intek V-Twin & Single Horsepower Range 14HP – 18HP Included Carburetor, Gaskets, Fuel Filter Fuel Type Gasoline Compatible Equipment Craftsman YT & LT Series Riding Mowers (14-18HP Intek) Husqvarna YTH & LGT Series Tractors Poulan Pro Riding Mowers John Deere 100 Series (Intek-powered models) Murray Widebody Lawn Tractors Toro TimeCutter & Titan (select models) Snapper NXT & SPX Series Installation Guide Disconnect the battery and remove the spark plug wire for safety. Remove the air filter housing and disconnect the fuel line. Have a rag ready to catch fuel drips. Disconnect the governor linkage, choke linkage, and throttle cable from the old carburetor. Take a photo for reference. Remove the two carburetor mounting bolts and lift off the old carburetor. Clean the mounting surface. Install the new carburetor with the supplied gaskets. Tighten mounting bolts evenly. Reconnect all linkages in the same positions you photographed. Install the inline fuel filter. Reconnect the fuel line and battery, then start the engine. Let it warm up and check for smooth idle and throttle response. Why Choose iFJF? iFJF Direct delivers OEM-quality replacement parts at prices that make sense for the DIY owner. Our 799727 carburetor undergoes a multi-point quality inspection including float level, throttle plate operation, and fuel passage clearance before packaging. Ships fast from our US warehouse. Frequently Asked Questions Will this carburetor fit my Craftsman LT2000? If your Craftsman LT2000 has a Briggs & Stratton Intek engine in the 14-18HP range and the original carburetor part number matches one of the cross-references listed (799727, 698620, etc.), this carburetor will fit. Always verify your engine model number before ordering. Is this carburetor ready to run out of the box? Yes. It comes pre-adjusted from the factory. Install it, connect the linkages, and start the engine. You may want to fine-tune the idle speed screw after the engine warms up, but major mixture adjustments are typically not needed. Does this include the fuel solenoid? The carburetor includes the fuel solenoid mounting port. If your original carburetor had an anti-afterfire solenoid, you can transfer it from the old carburetor to this one. A new solenoid is not included. What's the difference between rebuilding and replacing? Rebuilding works well for carbs that are dirty but structurally sound. Replacement is better when the carburetor body is corroded, the throttle shaft bore is worn (causing vacuum leaks), or internal passages are permanently clogged. At iFJF's price point, replacement is often the more reliable long-term solution. Do I need any special tools? Basic hand tools are all you need: a socket set (typically 1/2" and 7/16"), flathead and Phillips screwdrivers, and needle-nose pliers for linkage clips. A can of carburetor cleaner is helpful for cleaning the mounting surface. Related Products iFJF 796184 Carburetor Rebuild Kit + Air Filter iFJF 845273 Carburetor B&S 611477/613477 iFJF 699915 Fuel Solenoid for B&S

Read more less

Overview The iFJF 800M4 Vent Float Repair Kit is a precision replacement component for 1-inch 800QT series backflow prevention valves. Designed to restore proper vent float operation in irrigation and plumbing systems, this kit includes all necessary seals and components to rebuild your 800M4 backflow valve assembly. Compatible with OEM part numbers 0887715, 887715, and RK 800M4-FR-V1, it provides a cost-effective alternative to full valve replacement. Key Features Exact Fit Replacement: Precision-molded to match the original 800M4 vent float specifications, ensuring a leak-free seal and reliable backflow prevention for irrigation systems. Complete Repair Kit: Includes all seals, gaskets, and float components needed for a full rebuild of the 800QT series 1-inch backflow valve vent assembly. Chemical-Resistant Materials: Constructed from durable elastomers that withstand chlorine, irrigation chemicals, fertilizers, and UV exposure for extended outdoor service life. Cost-Effective Rebuild: Save 60-80% compared to replacing the entire backflow preventer assembly. This repair kit pays for itself with a single use. Universal 1-Inch Compatibility: Works with 800QT, 800M4, and compatible 1-inch backflow preventer assemblies from major manufacturers including Febco and Watts. DIY-Friendly Install: Drop-in replacement design with no special tools required. Complete the repair in under 30 minutes with basic hand tools. Compatibility Brand Model Size Febco 800M4 1" Febco 800QT 1" Watts 800M4-FR 1" Specifications Specification Value OEM Part Numbers 0887715, 887715, RK 800M4-FR-V1 Valve Size 1 inch Valve Series 800QT / 800M4 Application Backflow Prevention Valve Material Chemical-Resistant Elastomer SKU FJ-TOOL155-800M4 Why Choose iFJF? At iFJF Direct, we specialize in high-quality replacement parts backed by rigorous quality control. Each repair kit component is manufactured to meet or exceed OEM specifications, ensuring reliable backflow prevention performance. We stand behind every product with responsive customer support and a satisfaction guarantee. Backflow valve failure can contaminate your water supply — trust a properly engineered repair kit for this critical safety device. Frequently Asked Questions Q: Does this fit all 1-inch backflow valves?A: This kit is specifically designed for Febco 800M4 and 800QT series 1-inch backflow prevention valves. It is also compatible with OEM part numbers 0887715 and 887715. Please verify your valve model before ordering. Q: How do I know if my vent float needs replacement?A: Common signs include water leaking from the vent, the valve failing annual backflow testing, or the float showing visible cracks or deterioration. If your backflow valve fails its annual test, the vent float is often the root cause. Q: Is this a complete rebuild kit for the entire valve?A: This is a vent float repair kit specifically. It includes all components needed to rebuild the vent float assembly — seals, gaskets, and the float itself. For a complete valve rebuild, additional kits may be needed. Q: Do I need a licensed plumber to install this?A: While many experienced DIYers can perform the repair, backflow prevention devices are part of your water safety system. We recommend having the valve professionally tested after repair to ensure compliance with local plumbing codes and to verify proper backflow prevention. Q: How often should backflow valves be serviced?A: Most municipalities require annual backflow testing. Internal components like the vent float typically need replacement every 3-5 years depending on water quality, chemical exposure, and frequency of use. A proactive replacement schedule prevents unexpected failures. Package Includes 1 x 800M4 Vent Float Repair Kit for 1" Backflow Valve | Complete seals & components | Product support documentation

Read more less

Overview The iFJF 80647-ZC00A Chrome Door Handle Keyhole Frame Cover is a precision-fit exterior trim piece for Nissan Titan (2004-2019) and Armada (2004-2015) models. This chrome bezel replaces a worn, faded, or missing keyhole frame on the driver's side exterior door handle, restoring your vehicle's appearance with a showroom-quality finish. Manufactured to OEM specifications, it directly replaces part numbers 80647-ZC00A and 80647-9FU0B. Key Features OEM-Spec Chrome Finish: Triple-layer chrome plating provides a mirror-like finish that matches factory trim and resists oxidation, peeling, and fading for years of service. Precision Nissan Fit: Engineered to exact specifications for seamless fitment on the driver's side exterior door handle keyhole area — no gaps, no loose fit. UV-Resistant Coating: Advanced UV-stabilized protective layer prevents yellowing and degradation from prolonged sun exposure, keeping your chrome looking fresh. Snap-On Installation: Factory-style clip design allows tool-free installation in seconds. No drilling, no adhesive, no modifications required — just align and press into place. Corrosion-Resistant: Base material is treated with anti-corrosion primer before triple chrome plating, ensuring durability through rain, snow, salt, and extreme temperatures. Cost-Effective Upgrade: Restore your vehicle's appearance at a fraction of dealership prices while getting the same OEM-quality look and fit. Compatibility Make Model Year Range Nissan Titan 2004-2019 Nissan Armada 2004-2015 Specifications Specification Value OEM Part Numbers 80647-ZC00A, 80647-9FU0B Position Driver Side Exterior Material ABS Plastic + Triple Chrome Plating Color Bright Chrome Installation Snap-On / Clip-On (No Tools) SKU FJ-CMBS-ZC00A Why Choose iFJF? At iFJF Direct, we specialize in high-quality replacement parts backed by rigorous quality control. This chrome keyhole cover is manufactured to meet or exceed OEM specifications for fit, finish, and durability. We stand behind every product with responsive customer support and a satisfaction guarantee. Don't let a missing or corroded keyhole cover detract from your vehicle's appearance — this simple upgrade makes a noticeable difference. Frequently Asked Questions Q: Will this fit both Titan and Armada?A: Yes. This chrome keyhole frame cover fits the driver's side exterior door handle on Nissan Titan (2004-2019) and Nissan Armada (2004-2015). It replaces OEM part numbers 80647-ZC00A and 80647-9FU0B. Q: How do I install this keyhole cover?A: Installation takes seconds — simply align the cover with the keyhole on your driver's side door handle and press firmly until it snaps into place. No tools, no adhesive, no modifications needed. Q: Will the chrome finish hold up in harsh weather?A: Yes. The triple-layer chrome plating and UV-stabilized coating are designed to withstand extreme temperatures, rain, snow, road salt, and direct sunlight without peeling, fading, or corroding. Q: Is this an OEM or aftermarket part?A: This is a high-quality aftermarket replacement manufactured to OEM specifications. It matches the fit and finish of the factory part at a significantly more affordable price point. Q: Does this include both driver and passenger sides?A: This listing is for the driver's side (left) keyhole frame cover only, as the passenger side typically does not have a keyhole on these Nissan models. Package Includes 1 x 80647-ZC00A Chrome Door Handle Keyhole Frame Cover (Driver Side) | Product support documentation

Read more less

Overview The iFJF 80670-3TA0D Interior Door Handle is a premium replacement for the passenger side (right) front or rear door on select Nissan models including Altima (2013-2018), Armada (2014-2015), Murano (2015-2021), Pathfinder (2013-2020), Titan (2014-2019), and Titan XD (2015-2021). Engineered with reinforced internal structure at the pivot point — the most common failure location — and OEM-spec mounting points, this handle restores smooth door operation and cabin aesthetics. Key Features Reinforced Pivot Construction: Internal ribbing and premium-grade ABS plastic provide superior strength at the pivot point where OEM handles commonly snap, especially in hot climates. Exact OEM Fit: Precision-molded to match factory dimensions and mounting points. Direct replacement for part numbers 80670-3TA0D and 80670-3TA0B with zero modification required. Factory-Matched Texture: Textured black grip surface exactly matches the original interior trim finish, maintaining your vehicle's factory appearance and feel. Complete Pre-Assembled Unit: Arrives fully assembled with the internal spring mechanism — no small parts to transfer from your broken handle. Ready to install out of the box. Standard 2-Bolt Mounting: Uses the factory two-bolt mounting pattern. Existing door panel hardware is fully reusable — no special fasteners needed. Fade-Resistant Finish: UV-stabilized black material maintains its color and won't discolor even with years of sun exposure through side windows. Compatibility Make Model Year Range Nissan Altima 2013-2018 Nissan Armada 2014-2015 Nissan Murano 2015-2021 Nissan Pathfinder 2013-2020 Nissan Titan 2014-2019 Nissan Titan XD 2015-2021 Specifications Specification Value OEM Part Numbers 80670-3TA0D, 80670-3TA0B Position Passenger Side (Right) Front/Rear Material Reinforced ABS Plastic Color Black (Textured) Mounting Type 2-Bolt Pattern SKU FJ-CMBS-3TA0D-R Why Choose iFJF? At iFJF Direct, we focus on addressing the real failure points that OEM parts miss. Our reinforced pivot design specifically targets the area where factory handles crack under repeated stress. Each unit undergoes dimensional verification to ensure plug-and-play fitment. We stand behind every product with responsive support and a satisfaction guarantee. Frequently Asked Questions Q: How do I know this is the correct side?A: The 80670-3TA0D is for the PASSENGER side (RIGHT). If you need the driver side (LEFT), please order part 80671-3TA0D. Always verify which door handle is broken before ordering. Q: What tools do I need for installation?A: A Phillips screwdriver, a plastic trim removal tool, and optionally a 10mm socket (for some models). Total installation time is typically 20-30 minutes per door with basic DIY skills. Q: Does this fit both front and rear doors?A: Yes. This handle is compatible with both front and rear passenger-side doors on all listed Nissan models, giving you flexibility for any door repair. Q: My door handle snapped at the pivot — is this a common issue?A: Extremely common on these Nissan models, especially in hot climates where repeated thermal expansion and contraction weakens the plastic pivot point over time. Our reinforced design directly addresses this known failure mode. Q: Do I need to transfer parts from my old handle?A: No. This handle arrives as a complete assembly with the internal spring pre-installed. Simply remove the old handle and bolt this one in place. Package Includes 1 x 80670-3TA0D Interior Door Handle (Passenger Side Right) | Pre-assembled with spring mechanism | Product support documentation

Read more less

Overview The iFJF 80671-3TA0D Interior Door Handle is a premium replacement for the passenger side (right) front or rear door on select Nissan models including Altima (2013-2018), Armada (2014-2015), Murano (2015-2021), Pathfinder (2013-2020), Titan (2014-2019), and Titan XD (2015-2021). Engineered with reinforced internal structure at the pivot point — the most common failure location — and OEM-spec mounting points, this handle restores smooth door operation and cabin aesthetics. Key Features Reinforced Pivot Construction: Internal ribbing and premium-grade ABS plastic provide superior strength at the pivot point where OEM handles commonly snap, especially in hot climates. Exact OEM Fit: Precision-molded to match factory dimensions and mounting points. Direct replacement for part numbers 80671-3TA0D and 80670-3TA0B with zero modification required. Factory-Matched Texture: Textured black grip surface exactly matches the original interior trim finish, maintaining your vehicle's factory appearance and feel. Complete Pre-Assembled Unit: Arrives fully assembled with the internal spring mechanism — no small parts to transfer from your broken handle. Ready to install out of the box. Standard 2-Bolt Mounting: Uses the factory two-bolt mounting pattern. Existing door panel hardware is fully reusable — no special fasteners needed. Fade-Resistant Finish: UV-stabilized black material maintains its color and won't discolor even with years of sun exposure through side windows. Compatibility Make Model Year Range Nissan Altima 2013-2018 Nissan Armada 2014-2015 Nissan Murano 2015-2021 Nissan Pathfinder 2013-2020 Nissan Titan 2014-2019 Nissan Titan XD 2015-2021 Specifications Specification Value OEM Part Numbers 80671-3TA0D, 80670-3TA0B Position Passenger Side (Right) Front/Rear Material Reinforced ABS Plastic Color Black (Textured) Mounting Type 2-Bolt Pattern SKU FJ-CMBS-3TA0D-L Why Choose iFJF? At iFJF Direct, we focus on addressing the real failure points that OEM parts miss. Our reinforced pivot design specifically targets the area where factory handles crack under repeated stress. Each unit undergoes dimensional verification to ensure plug-and-play fitment. We stand behind every product with responsive support and a satisfaction guarantee. Frequently Asked Questions Q: How do I know this is the correct side?A: The 80671-3TA0D is for the DRIVER side (LEFT). If you need the driver side (LEFT), please order part 80671-3TA0D. Always verify which door handle is broken before ordering. Q: What tools do I need for installation?A: A Phillips screwdriver, a plastic trim removal tool, and optionally a 10mm socket (for some models). Total installation time is typically 20-30 minutes per door with basic DIY skills. Q: Does this fit both front and rear doors?A: Yes. This handle is compatible with both front and rear passenger-side doors on all listed Nissan models, giving you flexibility for any door repair. Q: My door handle snapped at the pivot — is this a common issue?A: Extremely common on these Nissan models, especially in hot climates where repeated thermal expansion and contraction weakens the plastic pivot point over time. Our reinforced design directly addresses this known failure mode. Q: Do I need to transfer parts from my old handle?A: No. This handle arrives as a complete assembly with the internal spring pre-installed. Simply remove the old handle and bolt this one in place. Package Includes 1 x 80671-3TA0D Interior Door Handle (Driver Side Left) | Pre-assembled with spring mechanism | Product support documentation

Read more less

Overview The iFJF 813402 50mm Awning Bracket is a heavy-duty gusseted mounting solution for roof-top awnings on vehicles with 50mm crossbars. Compatible with Thule Profession, WingBar, AeroBar, and Rhino heavy-duty T-slot systems, these powder-coated steel brackets provide a secure, rattle-free foundation for your vehicle-mounted awning. The gusseted design adds structural rigidity, preventing flex and vibration during off-road and highway use. Key Features Gusseted Heavy-Duty Design: Triangular gusset reinforcement provides superior lateral stability compared to flat brackets, preventing awning sag and vibration on rough terrain. Universal 50mm Compatibility: Precision-engineered to fit all 50mm crossbars including Thule Profession, WingBar, AeroBar, Rhino heavy-duty, and most aftermarket roof racks with T-slot channels. Corrosion-Resistant Powder Coat: Black powder-coated steel provides excellent weather resistance for year-round outdoor use, from desert heat to coastal salt air. T-Slot Ready Hardware: Includes stainless steel T-bolts, T-nuts, and washers for complete installation. Hardware slides directly into crossbar channels. Dual Clamping Points: Extended bracket design provides dual clamping points per bracket, ensuring your awning stays securely mounted even at highway speeds. Low-Profile Aesthetics: Sleek black powder-coated finish complements any vehicle color and roof rack setup without adding excessive height or visual bulk. Compatibility Make Model Year/Type Thule Profession Bar 50mm Thule WingBar 50mm Thule AeroBar 50mm Rhino Heavy Duty Bar 50mm Universal T-Slot Crossbars 50mm Specifications Specification Value Bracket Width 50mm Material Steel + Black Powder Coat Compatibility T-Slot Channel Crossbars Package 2 Brackets + Mounting Hardware SKU FJ-ZJ-813402 Why Choose iFJF? At iFJF Direct, we specialize in high-quality replacement parts backed by rigorous quality control. Each component is manufactured to meet or exceed OEM specifications, ensuring reliable performance and long service life. We stand behind every product with responsive customer support and a satisfaction guarantee. Frequently Asked Questions Q: Will these brackets fit my Thule WingBar?A: Yes. These brackets are specifically designed for 50mm crossbars including all Thule bar types. They use the T-slot channel for secure, rattle-free mounting. Q: What is the advantage of gusseted brackets?A: Gusseted brackets feature a triangular reinforcement between the mounting plate and vertical support. This dramatically reduces lateral movement and vibration compared to flat L-brackets, making them ideal for off-road use and heavier awnings. Q: Do these come with mounting hardware?A: Yes. Each pair includes stainless steel T-bolts, T-nuts, flat washers, and lock washers — all corrosion-resistant for outdoor use. Q: Can I install these on aftermarket crossbars?A: Yes, as long as your crossbars have a standard T-slot channel and are approximately 50mm wide. These brackets work with most aftermarket roof racks. Package Includes 1 x iFJF 813402 50mm Awning Bracket Gusseted Awning Holder Compatible with Thule Rhino Heavy Duty Bar | Installation hardware as shown | Product support documentation

Read more less

Overview The iFJF 8183061 Tire Machine Mount Head 5-Pack is a set of nylon plastic replacement duck heads for Coats tire changers. Compatible with Coats models 5030 through 7665 (all baseline series), this mount head replaces OEM part numbers 8183061, 183061, 8182960, 182960, 8183060, 183060, 8182788, and 182788. The nylon construction protects alloy and custom wheels from scratching during tire mounting and demounting — a critical consideration for high-end wheel service. Key Features Wheel-Safe Nylon Material: High-density nylon is tough enough for daily shop use but softer than wheel materials (aluminum, chrome, clear coat), preventing scratches on expensive wheels. 5-Pack Shop Value: Five mount heads provide months of continuous shop use at a fraction of single OEM replacement cost. Keep spares on hand to eliminate downtime. Broad Coats Compatibility: Fits virtually all Coats baseline tire changer models — 5000, 6000, and 7000 series — covering the most common machines in North American tire shops. Precision CNC-Molded: CNC-machined mold ensures exact dimensional tolerance for smooth bead handling without binding or excessive wear on the mount/demount head. Quick-Change Design: Standard quick-release mounting allows tool-free replacement in under 30 seconds, minimizing machine downtime during busy shop hours. Professional-Grade Durability: Engineered for high-volume tire shops processing 50+ tires daily. Nylon formulation resists chipping and cracking under heavy use. Compatibility Make Model Year/Type Coats 5030/5040/5050 BaseLine Coats 5060/5065 BaseLine Coats 6050/6060/6065 BaseLine Coats 7050/7055/7060/7065 BaseLine Coats 7660/7665 BaseLine Specifications Specification Value Replaces OEM 8183061, 183061, 8182960, 182960, 8183060, 183060, 8182788, 182788 Material High-Density Nylon Pack Size 5 Pieces (Black) Application Tire Mount/Demount Duck Head SKU FJ-TOOL124-5 Why Choose iFJF? At iFJF Direct, we specialize in high-quality replacement parts backed by rigorous quality control. Each component is manufactured to meet or exceed OEM specifications, ensuring reliable performance and long service life. We stand behind every product with responsive customer support and a satisfaction guarantee. Frequently Asked Questions Q: Which Coats models does this fit?A: This mount head fits all baseline Coats models: 5030, 5040, 5050, 5060, 5065, 6050, 6060, 6065, 7050, 7055, 7060, 7065, 7660, and 7665. Compare your existing duck head to product images if unsure. Q: Will this scratch customer wheels?A: No. The nylon material is specifically chosen because it is softer than aluminum, chrome, and clear coat. It provides the rigidity needed for tire mounting while being gentle on wheel finishes. Q: How long does one head last?A: In a busy shop (30-50 tires/day), each nylon head lasts 2-4 weeks depending on tire types and operator technique. This 5-pack provides months of service with spares always ready. Q: How do I install the new mount head?A: Most Coats machines use a quick-release pin or bolt. Remove the old head, align the new one in the bracket, and secure with original hardware. Takes less than 30 seconds. Package Includes 1 x iFJF 8183061 TC183061 Tire Machine/Changer Mount Head Nylon Plastic Replacement for Coats 8182960 182960 8183060 183060 183060 (5 Pack Black) | Installation hardware as shown | Product support documentation

Read more less

Overview The iFJF 830472P002 RV Awning Arm Slider Catch Kit is a direct replacement for Dometic A&E 8500 and 9000 series manual patio awnings. This 2-pack includes precision-molded UV-stabilized slider catches that secure the awning arm in the closed/travel position, preventing rattling and accidental deployment during transit. Tool-free snap-in installation makes this one of the quickest RV maintenance items you'll ever do. Key Features Exact Fit Replacement: Designed specifically for Dometic A&E 8500 and 9000 series manual awnings. Matches OEM part 830472P002 dimensions for a secure, rattle-free travel lock. 2-Pack Complete Kit: Includes two slider catches — enough for both awning arms. Replacing both sides ensures even tension, smooth operation, and balanced wear. UV-Stabilized Polymer: High-impact resistant material with UV inhibitors prevents yellowing, brittleness, and cracking from years of sun exposure on the side of your RV. Secure Travel Lock Function: Properly functioning slider catches prevent awning arms from rattling or partially deploying during highway travel, protecting both the awning fabric and your vehicle. Tool-Free Snap-In Install: Simply snap the new catch into the existing channel on the awning arm. No tools, no drilling, no adhesives — complete both sides in under 5 minutes. Smooth Channel Action: Precision molding ensures the catch glides smoothly along the awning arm channel without binding, making setup and takedown effortless every time. Compatibility Make Model Year/Type Dometic/A&E 8500 Series Manual Patio Awning Dometic/A&E 9000 Series Manual Patio Awning Specifications Specification Value OEM Part Number 830472P002 Material UV-Stabilized High-Impact Polymer Pack Size 2 Slider Catches Compatibility A&E 8500 & 9000 Awnings SKU FJ-HL05-P002 Why Choose iFJF? At iFJF Direct, we specialize in high-quality replacement parts backed by rigorous quality control. Each component is manufactured to meet or exceed OEM specifications, ensuring reliable performance and long service life. We stand behind every product with responsive customer support and a satisfaction guarantee. Frequently Asked Questions Q: How do I know if I need new slider catches?A: If your awning arm rattles during travel, the catch is cracked or chipped, or the awning arm won't stay locked in the closed position, your slider catches need immediate replacement. Q: Does this fit both 8500 and 9000 series?A: Yes. The 830472P002 slider catch is compatible with both Dometic A&E 8500 and 9000 series manual patio awnings, which share the same arm design across both series. Q: How long do these catches typically last?A: With UV-stabilized polymer, expect 3-5 years under normal conditions. RVs stored outdoors in intense sun may need earlier replacement. Inspect annually during spring de-winterization. Q: Why replace both sides?A: Replacing both catches ensures equal tension and wear. If one side has failed, the other is likely close behind. The 2-pack lets you service both arms in one session. Package Includes 1 x iFJF 830472P002 RV Awning Arm Slider Catch Kit Compatible with A&E 8500 9000 (2 Slider Catch) | Installation hardware as shown | Product support documentation

Read more less

Overview The iFJF 830644 Deluxe Awning Handle is a premium replacement lift handle for Dometic and A&E 8500/9000 series manual RV patio awnings. Molded from durable polyethylene with an ergonomic morphological grip design, this handle makes raising and lowering your RV awning effortless while providing a comfortable, secure hold even in wet conditions. Key Features Ergonomic Morphological Grip: The handle shape follows the natural curve of your hand, distributing pressure evenly across your palm to reduce fatigue during awning setup and takedown. Durable Polyethylene Construction: High-density polyethylene resists cracking, fading, and UV deterioration while remaining lightweight and comfortable to handle. Smooth Polished Finish: The polished surface prevents splinters and rough spots even after years of outdoor exposure, making it comfortable for bare-hand use in any weather. Universal Awning Fit: Designed to fit Dometic and A&E 8500/9000 series manual awnings, covering the vast majority of RV patio awnings on the road today. Direct OEM Replacement: Replaces the original Dometic/A&E deluxe handle (830644) with identical fitment and improved material durability. Lightweight Design: At just a few ounces, this handle adds no meaningful weight to your awning assembly while providing years of reliable, comfortable service. Compatibility Make Model Year/Type Dometic/A&E 8500 Series Manual Patio Awning Dometic/A&E 9000 Series Manual Patio Awning Specifications Specification Value Part Number 830644 Material High-Density Polyethylene Type Deluxe Awning Lift Handle Compatibility A&E 8500 & 9000 SKU TOOL85-CK Why Choose iFJF? At iFJF Direct, we specialize in high-quality replacement parts backed by rigorous quality control. Each component is manufactured to meet or exceed OEM specifications, ensuring reliable performance and long service life. We stand behind every product with responsive customer support and a satisfaction guarantee. Frequently Asked Questions Q: Will this handle fit my Dometic awning?A: Yes. This deluxe handle is designed for Dometic and A&E 8500 and 9000 series manual patio awnings — the most common RV awnings on the market. If your awning arm has a hook/pin at the bottom, this handle will work. Q: My old handle cracked — will this last longer?A: Our high-density polyethylene formulation includes UV stabilizers that significantly extend outdoor lifespan. The smooth polished finish resists stress cracking better than textured alternatives. Q: Is this difficult to install?A: Not at all. Simply slide the handle onto the awning arm rod and it's ready to use — no tools, fasteners, or adhesives needed. Installation takes seconds. Q: Does this include the rafter rivet?A: This SKU is for the handle only. If you need both the handle and the rafter rivet, see our combo kit (SKU FJ-TOOL85-HL02-1) which includes both items. Package Includes 1 x iFJF 830644 Deluxe Handle for A&E Awning Lift | Installation hardware as shown | Product support documentation

Read more less

Overview The iFJF 830644 Deluxe Handle & 830463P Awning Rafter Rivet combo kit provides everything needed to restore smooth, secure awning operation on Dometic and A&E 8500/9000 series RV awnings. This kit bundles our premium polyethylene ergonomic deluxe lift handle with a heavy-duty steel-aluminum rafter rivet for the awning arm pivot joint. Purchase both commonly replaced awning components in one convenient, cost-saving package. Key Features Complete Awning Hardware Kit: Includes 1x Deluxe Lift Handle (830644) and 1x Rafter Rivet (830463P) — the two most commonly replaced awning components bundled together for convenience and savings. Ergonomic Handle: Morphological grip design conforms to your hand for comfortable, secure awning operation. Smooth polyethylene finish resists splintering and UV degradation. Heavy-Duty Rafter Rivet: Steel-aluminum construction with thick mandrel provides the strength needed for the awning arm pivot. Corrosion-resistant for long outdoor service life. Self-Piercing Design: The rafter rivet is engineered for easy installation through most awning arm materials without pre-drilling in the majority of applications. Complete A&E Compatibility: Fits all Dometic and A&E 8500 and 9000 series manual patio awnings, covering 90%+ of RV awnings on the road today. Bundle Value: Purchasing the combo kit is more economical than buying the handle and rivet separately, and ensures you have all parts for a complete awning arm service. Compatibility Make Model Year/Type Dometic/A&E 8500 Series Manual Patio Awning Dometic/A&E 9000 Series Manual Patio Awning Specifications Specification Value Handle Part 830644 Rivet Part 830463P Handle Material High-Density Polyethylene Rivet Material Steel-Aluminum Package 1 Handle + 1 Rafter Rivet SKU FJ-TOOL85-HL02-1 Why Choose iFJF? At iFJF Direct, we specialize in high-quality replacement parts backed by rigorous quality control. Each component is manufactured to meet or exceed OEM specifications, ensuring reliable performance and long service life. We stand behind every product with responsive customer support and a satisfaction guarantee. Frequently Asked Questions Q: What's included in this combo kit?A: The kit includes 1x Deluxe Awning Lift Handle (830644) and 1x Awning Rafter Rivet (830463P) — everything needed for common awning arm repairs on A&E 8500/9000 awnings. Q: How do I install the rafter rivet?A: Align the rivet through the awning arm pivot hole. Use a standard pop rivet tool to set it in place. The steel-aluminum construction is compatible with any standard rivet gun available at hardware stores. Q: Why buy the combo vs separately?A: The combo kit is priced lower than purchasing individually. Additionally, if you're servicing your awning arm, both parts often need replacement simultaneously — having them together saves a second order and shipping cost. Q: Do I need the rafter rivet if only my handle is damaged?A: The rafter rivet secures the awning arm pivot joint. If you notice the arm is loose, wobbles, or the existing rivet shows corrosion, it should be replaced along with the handle for a complete, lasting repair. Package Includes 1 x iFJF 830644 Deluxe Handle with 830463P Awning Rafter Rivet Replacement for A&E 8500 9000 (1 Rafter Rivet&1 Handle Lift) | Installation hardware as shown | Product support documentation

Read more less

Overview The iFJF 8318084 Washer Lid Switch is a direct replacement for Whirlpool, Kenmore, Maytag, KitchenAid, and other top-load washing machines. This safety interlock switch detects when the washer lid is closed, allowing the spin cycle to engage. Compatible with OEM part numbers AP3180933, PS886960, WP8318084, and AP6012742, this switch addresses the #1 cause of washing machines that fill with water but won't agitate or spin. Key Features OEM-Equivalent Performance: Manufactured to match Whirlpool OEM specifications (WP8318084) for reliable lid detection and spin cycle engagement. Meets all safety interlock requirements. Broad Brand Compatibility: Fits Whirlpool, Kenmore, Maytag, KitchenAid, Roper, Estate, Inglis, and Amana top-load washers using the WPL 8318084 switch design. 3-Wire Plug-and-Play: Standard 3-terminal wiring harness connector for direct plug-in installation. No wire cutting, splicing, or soldering required — simply unplug old and plug in new. Resolves Key Symptoms: Fixes most common washer issues: won't spin, stops mid-cycle, fills but won't agitate, or lid locks but won't start. The lid switch is the #1 cause of all these symptoms. High-Cycle Rated: Switch mechanism is rated for thousands of open/close cycles, ensuring years of reliable daily operation in household laundry use. Safety Certified: Meets UL and CSA safety standards for appliance lid interlock switches, providing proper spin basket braking when the lid is opened. Compatibility Make Model Year/Type Whirlpool Various Top-Load 1990s-2010s Kenmore Various Top-Load 1990s-2010s Maytag Various Top-Load 2000s-2010s KitchenAid Various Top-Load 2000s-2010s Amana Various Top-Load 2000s-2010s Specifications Specification Value OEM Part Numbers 8318084, AP3180933, PS886960, WP8318084, AP6012742 Connector Type 3-Wire Harness Application Washer Lid Safety Switch Voltage 120V AC Certification UL / CSA Safety Listed SKU FJ-CMBS-8318084 Why Choose iFJF? At iFJF Direct, we specialize in high-quality replacement parts backed by rigorous quality control. Each component is manufactured to meet or exceed OEM specifications, ensuring reliable performance and long service life. We stand behind every product with responsive customer support and a satisfaction guarantee. Frequently Asked Questions Q: How do I know my lid switch is bad?A: Common symptoms: washer won't spin, washer agitates but stops before spinning, washer won't start at all, or stops mid-cycle. Test with a multimeter — it should show continuity when the lid is closed and open when the lid is raised. Q: Is this the same as OEM WP8318084?A: Yes. This switch is manufactured to the same specifications as Whirlpool OEM part WP8318084. It's a direct fit, plug-and-play replacement with no modifications needed. Q: Do I need to cut any wires?A: No. The switch features a standard 3-wire connector that plugs directly into your washer's existing wiring harness. Simply unplug the old switch and plug in the new one. Q: What tools are needed?A: Typically just a Phillips screwdriver and a flathead screwdriver to release cabinet clips. Most installations take 20-40 minutes. The switch is accessible from the top of the washer under the control panel. Q: My washer fills but won't spin — is this the fix?A: If your washer fills with water but doesn't start spinning, the lid switch is the most likely cause. The switch directly controls spin cycle activation as a safety interlock. Package Includes 1 x iFJF 8318084 Washer Lid Switch AP3180933 PS886960 WP8318084 AP6012742 For Whirlpool | Installation hardware as shown | Product support documentation

Read more less

iFJF 8333A9021 AC Hard Start Device — Coleman RV Air Conditioners If your RV air conditioner struggles to start — dimming the lights, tripping the breaker, or refusing to run on a portable generator — the iFJF 8333A9021 hard start device is the solution. This compact capacitor gives your Coleman AC compressor the extra torque it needs during startup, reducing the electrical surge and letting your air conditioner run smoothly on 30-amp campground power, smaller generators, or even inverter systems. Installation takes 15 minutes with basic tools and no specialized HVAC knowledge. Key Features & Benefits Reduces Startup Current Draw The hard start device stores electrical energy and releases it during compressor startup, reducing the momentary current spike by up to 50%. This means your AC starts reliably on 30-amp service, won't trip the breaker, and can run on a 2,000-2,500 watt portable generator that previously couldn't handle the startup load. Compatible with Coleman 8000 & 11000 Series Engineered for all Coleman 8000 series rooftop AC units as well as 11,000 BTU and 13,500 BTU and 15,000 BTU models. Also works with many other RV rooftop AC brands — the universal 3-terminal design fits most single-phase compressor setups. Check your AC's wiring diagram before installation to confirm compatibility. 15-Minute DIY Installation Includes detailed wiring instructions. The device connects to the compressor's Run, Start, and Common terminals — the same three terminals you'll find on almost every RV rooftop AC compressor. No refrigerant handling, no special tools. Just a screwdriver and basic wiring knowledge. Protects Your AC Compressor Hard starts don't just make the AC easier to start — they reduce wear on the compressor by shortening the inrush current duration. A compressor that struggles to start runs hotter and wears faster. The iFJF 8333A9021 helps extend your air conditioner's service life. Technical Specifications Specification Detail Model iFJF 8333A9021 Application RV Rooftop Air Conditioner Compatibility Coleman 8000 Series, 11K/13.5K/15K BTU Voltage 120V AC Connection Type 3-Terminal (Run / Start / Common) Installation Time ~15 Minutes Compatible RV AC Models Coleman Mach 3, Mach 3+, Mach 8, Mach 10, Mach 15 Coleman 8000 Series (all BTU ratings) Coleman 11000 BTU Rooftop Units Coleman 13500 BTU Rooftop Units Coleman 15000 BTU Rooftop Units Many Dometic & Advent RV AC units (universal fit) Installation Instructions Turn off ALL power to the RV. Unplug from shore power and turn off the generator. The AC capacitor stores high voltage — wait 5 minutes for it to discharge after disconnecting power. Remove the AC shroud (typically 4 screws) to access the compressor and capacitor terminals. Identify the three compressor terminals: Run (R), Start (S), and Common (C). They're usually labeled on the compressor or can be identified from the original capacitor wiring. Connect the hard start device wires: Red to Start, White to Run, Black to Common. Use the included crimp connectors for secure, vibration-resistant connections. Secure the device inside the AC housing with the included mounting bracket or heavy-duty zip ties. Reinstall the shroud, restore power, and test. The AC should start more quickly and with less electrical noise than before. Why Choose iFJF? iFJF Direct understands the RV lifestyle. Our 8333A9021 hard start device is built to handle the heat, vibration, and temperature extremes of rooftop RV installations. Every unit is tested before shipping, and we stand behind it with a satisfaction guarantee. Enjoy cooler camping, quieter generator operation, and a longer-lasting AC unit. Frequently Asked Questions Will this let me run my AC on a 2000-watt generator? In most cases, yes. A 2,000-watt generator typically can't handle the startup surge of a 13,500 BTU RV air conditioner (which can spike to 3,000+ watts momentarily). The hard start device reduces this startup surge, often enabling a 2,000 or 2,200-watt generator to successfully start and run a 13,500 BTU AC unit. Actual results depend on generator quality and ambient temperature. Can I install this myself or do I need an HVAC tech? This is a DIY-friendly installation if you're comfortable with basic wiring. The device connects to the compressor's three terminals using simple spade connectors. No refrigerant work is involved. If you're not confident with electrical work, any RV technician can install it in under 30 minutes. Will this hard start device work with my Dometic AC? While designed and tested primarily for Coleman units, the iFJF 8333A9021 uses universal 3-terminal connections compatible with most single-phase RV AC compressors, including many Dometic, Advent, and Atwood models. Check your compressor terminal layout before ordering. Does the hard start capacitor need to be replaced periodically? Hard start capacitors are durable components rated for thousands of cycles. Under normal RV use, expect 5+ years of reliable service. If you notice the AC struggling to start again after years of use, the capacitor may be wearing out and a replacement is recommended. Can I use this on a home window AC unit? Technically, the iFJF 8333A9021 can work with any 120V single-phase compressor having accessible Run/Start/Common terminals. However, it is specifically designed for the RV rooftop environment and form factor. For home AC applications, check the capacitor's voltage and microfarad (µF) rating against your unit's specifications. Related Products iFJF 93866 RV Water Heater Thermal Cutoff Kit iFJF Bluetooth Battery Isolator Switch iFJF Extended Run Gas Cap for Generators

Read more less

Overview The iFJF 835257Q1 Propeller Engine Replacement Kit is a comprehensive solution for Mercury and Mariner outboard engines (1984+) in the 75-125 HP range. This kit includes all essential components for propeller hub and drivetrain service, providing everything needed to replace worn or spun propeller components. Engineered to OEM specifications, this kit helps restore smooth power delivery and eliminate propeller hub slip. Key Features Complete Service Kit: Includes propeller hub components, thrust washer, and all necessary hardware for a full propeller drive system service on Mercury/Mariner 75-125 HP outboards. Eliminates Hub Slip: Worn hub components cause power loss through propeller slip. This kit restores direct power transfer from engine to water for maximum performance and fuel efficiency. Marine-Grade Materials: All components manufactured from corrosion-resistant materials suitable for both freshwater and saltwater marine environments. Precision Fit: Engineered to exact Mercury/Mariner specifications for proper spline engagement and thrust surface alignment. No modification or adjustment needed. Cost-Effective Rebuild: Save hundreds compared to purchasing a complete propeller assembly. This kit addresses the most common wear points that cause performance issues. Wide Model Coverage: Compatible with Mercury and Mariner outboards from 1984+, covering 75 HP through 125 HP models with standard propeller hub design. Compatibility Make Model Year/Type Mercury 75-125 HP 1984+ Mariner 75-125 HP 1984+ Specifications Specification Value Part Number 835257Q1 Engine HP Range 75-125 HP Year Compatibility 1984+ Application Propeller Hub Service Material Marine-Grade Corrosion Resistant SKU FJ-TOOL161 Why Choose iFJF? At iFJF Direct, we specialize in high-quality replacement parts backed by rigorous quality control. Each component is manufactured to meet or exceed OEM specifications, ensuring reliable performance and long service life. We stand behind every product with responsive customer support and a satisfaction guarantee. Frequently Asked Questions Q: Will this kit fit my 1990 Mercury 90 HP?A: Yes. This kit is compatible with Mercury and Mariner 75-125 HP outboard engines from 1984 forward, including 1990 90 HP models. Q: What are signs of a spun propeller hub?A: Key symptoms: engine revs increase but boat speed doesn't, a burning rubber smell near the propeller, or the engine hits the rev limiter at lower-than-normal speeds. A spun hub means the propeller isn't gripping the driveshaft. Q: Is this a complete propeller replacement?A: No. This is a propeller hub/drivetrain service kit that addresses the internal hub components. It's designed to restore a propeller with a spun or worn hub rather than replacing the entire propeller. Q: Can I install this myself?A: Yes, with basic mechanical skills and common tools. You'll need a prop wrench to remove the propeller first. Many boaters perform this service at home; however, professional installation is recommended for those unfamiliar with marine drivetrain systems. Package Includes 1 x iFJF 835257Q1 Propeller Engine Replacement Kit For Mercury/Mariner1984+ 75hp 1978+ 90hp 115hp 1994+ 125hp Replaces Mercury 835257K1 | Installation hardware as shown | Product support documentation

Read more less

iFJF 845273 Replacement Carburetor — Briggs & Stratton 611477 / 613477 Series The iFJF 845273 is a complete replacement carburetor for Briggs & Stratton 611477 and 613477 series engines found on lawn mowers, pressure washers, tillers, and other outdoor power equipment. If your engine surges, stalls under load, or refuses to start despite fresh fuel and a clean spark plug, a worn carburetor is the likely culprit. Our direct-fit replacement bolts on in minutes and comes pre-adjusted for reliable operation right out of the box. Key Features & Benefits OEM-Spec Replacement Engineered to match B&S part numbers 845273, 842097, 844172, and 845032. The throttle and choke linkage mounting points, fuel inlet position, and mounting bolt pattern are identical to the OEM carburetor — no modifications, no adapter plates, no frustration. Complete Kit — Carburetor + Fuel Filter + Gaskets Includes the carburetor, mounting gaskets, and an inline fuel filter. The filter catches debris before it reaches your new carburetor, protecting your investment from the first start. Everything arrives in one box. Pre-Adjusted Fuel Mixture Factory-set for the correct air-fuel ratio on B&S 611477 and 613477 engines. Minor idle-speed adjustment may be needed for your specific application, but you won't need to mess with the mixture screws. Technical Specifications Specification Detail Model iFJF 845273 Replaces OEM B&S 845273, 842097, 844172, 845032 Engine Series B&S 611477, 613477 Included Carburetor, Gaskets, Fuel Filter Fuel Type Gasoline Common Applications Briggs & Stratton 611477 Series Walk-Behind Mowers B&S 613477 Series Self-Propelled Mowers Pressure Washers (B&S powered) Rotary Tillers & Cultivators Generators with B&S 550-650 Series Engines Lawn Edgers & Leaf Blowers Installation Disconnect spark plug wire. Turn fuel valve OFF or clamp the fuel line. Remove the air filter housing. Disconnect the throttle linkage and governor spring. Remove mounting bolts and lift off old carburetor. Clean the mounting surface. Install new carburetor with gaskets. Tighten bolts evenly. Reconnect linkages and install the inline fuel filter (arrow pointing toward carburetor). Restore fuel, reconnect spark plug, and start. Let warm up and adjust idle if needed. Frequently Asked Questions How do I know if my engine is a 611477 or 613477 series? The engine model number is stamped on the metal blower housing or valve cover. Look for a string like "12H802" or "126M02" — the first two digits indicate cubic inches (12), and the "H8" or "M0" prefix helps identify the series. You can also search your engine's full model number on the Briggs & Stratton website to confirm series compatibility. Does this carburetor come with a new primer bulb? The primer bulb is typically part of the air filter housing, not the carburetor itself. If your primer bulb is cracked or not working, it may need to be replaced separately. The carburetor does include the primer port for connection. Can I use this on a Craftsman mower? Yes, if your Craftsman mower has a B&S 611477 or 613477 series engine. Many Craftsman, Husqvarna, and MTD mowers use these engines. Always verify the engine model number rather than the mower brand/model. Will a new carburetor fix hard starting? In most cases, yes — if the hard starting is caused by a clogged or worn carburetor. If hard starting persists after replacement, check the spark plug, ignition coil, and valve clearances. Fresh fuel and a clean air filter also help significantly. Related Products iFJF 799727 Carburetor B&S Intek 14-18HP iFJF 796184 Carburetor Rebuild Kit + Air Filter iFJF 699915 Fuel Solenoid Valve

Read more less

Overview The iFJF 84905-47010 Trunk Rear Hatch Liftgate Door Handle Switch is a direct-fit replacement for select Toyota and Lexus vehicles. This exterior handle/switch assembly controls the electronic trunk/hatch release mechanism, replacing a faulty, cracked, or non-responsive OEM switch. Compatible with OEM part number 84905-47010, this replacement restores convenient keyless trunk access and resolves unresponsive rear hatch release button issues. Key Features Direct OEM Replacement: Manufactured to exact Toyota specifications (84905-47010), ensuring proper fitment, connector compatibility, and weather sealing for reliable operation. Integrated Electronic Switch: Built-in microswitch provides reliable electrical contact for the trunk/hatch release solenoid, sealed against moisture and dust ingress. Weather-Resistant Design: Rubber gasket seal and corrosion-resistant terminals protect against rain, car wash spray, road salt, and humidity exposure. Restores Keyless Trunk Access: A functioning tailgate release switch allows convenient trunk access without using the key fob or interior release — especially useful when hands are full. Complete Assembly: Includes the handle body, integrated switch module, wiring connector, and all mounting hardware. Ready to install right out of the box. Vehicle-Specific Engineering: Unlike universal switches, this part is engineered for the specific mechanical and electrical requirements of Toyota/Lexus rear hatch systems. Compatibility Make Model Year/Type Toyota Various Models 2010s Lexus Various Models 2010s Specifications Specification Value OEM Part Number 84905-47010 Function Trunk/Hatch Release Switch Connector Type Vehicle-Specific Plug Material ABS Plastic + Rubber Seal SKU FJ-CMBS-47010 Why Choose iFJF? At iFJF Direct, we specialize in high-quality replacement parts backed by rigorous quality control. Each component is manufactured to meet or exceed OEM specifications, ensuring reliable performance and long service life. We stand behind every product with responsive customer support and a satisfaction guarantee. Frequently Asked Questions Q: How do I know if my trunk release switch is bad?A: Common symptoms: exterior trunk/hatch release button does nothing, switch feels loose or spongy, rubber cover is cracked, or trunk only opens with key fob or interior release. If your key fob works but the exterior button doesn't, the switch is almost certainly the issue. Q: Is this difficult to install?A: Installation is typically straightforward: remove the interior trim panel on the hatch/trunk lid, unbolt the old switch, disconnect the wiring, connect the new switch, bolt in place, and replace trim. Most DIYers complete this in 30-45 minutes. Q: Will this fit my Toyota/Lexus?A: This switch replaces OEM part number 84905-47010. Verify this part number matches your vehicle's requirements before ordering. The number is typically printed on the old switch or found in your vehicle's parts catalog. Q: Does this come with a new gasket?A: Yes. The switch includes an integrated rubber weather seal/gasket to prevent water intrusion into the hatch/trunk lid, protecting the electrical connections from corrosion. Package Includes 1 x iFJF 84905-47010 Trunk Rear Hatch Liftgate Door Handle Switch Latch Cover Release Button Rubber Cover for 84840-21010 926-098 84840-47020 (Black) | Installation hardware as shown | Product support documentation

Read more less

Overview The iFJF 8508211 Trailer Brake Controller is a proportional electric brake control system designed for 1-4 axle trailers. Featuring a digital LED screen display and automatic leveling technology, this controller provides smooth, proportional braking based on your vehicle's actual deceleration rate. Compatible with most vehicles equipped with a 7-way trailer connector, it includes a manual override lever for emergency situations and pre-trip trailer brake testing. Key Features Proportional Braking Technology: Built-in accelerometer senses your vehicle's deceleration rate and applies trailer brakes proportionally — the harder you brake, the more braking force to the trailer for car-like stopping. Digital LED Display: Bright, easy-to-read screen shows real-time braking output level, connection status, and diagnostic codes. Simple push-button controls for precise gain adjustment. 1-4 Axle Support: Controls single, tandem, triple, and quad-axle trailers (up to 8 brake assemblies) — covering everything from small utility trailers to large campers and boat trailers. Automatic Leveling: Self-calibrates to mounting angle — no manual leveling knob required. Mount anywhere within 70 degrees of horizontal and it self-levels automatically. Manual Override Lever: Integrated slide lever applies trailer brakes independently of the vehicle — essential for trailer sway correction, pre-trip brake testing, and emergency stopping. Universal Vehicle Compatibility: Works with any vehicle equipped with a standard 7-way RV trailer connector. Compatible with both time-delay and proportional brake controller wiring harnesses. Compatibility Make Model Year/Type Universal All Vehicles 7-Way Connector Trailers Camper/Boat/Utility/Horse 1-4 Axles Specifications Specification Value Part Number 8508211 Control Type Proportional (Accelerometer) Display Digital LED Screen Axle Support 1-4 Axles (Up to 8 Brakes) Mounting Universal Bracket Included SKU FJ-CMBS-8508211 Why Choose iFJF? At iFJF Direct, we specialize in high-quality replacement parts backed by rigorous quality control. Each component is manufactured to meet or exceed OEM specifications, ensuring reliable performance and long service life. We stand behind every product with responsive customer support and a satisfaction guarantee. Frequently Asked Questions Q: What is proportional braking and why does it matter?A: Proportional braking uses an accelerometer to match trailer braking to your vehicle's deceleration. Unlike time-delay controllers with preset output, proportional controllers provide smoother stops, less brake wear, and safer emergency braking — especially with varying trailer loads. Q: Will this work with my truck's factory tow package?A: Yes. This controller works with any vehicle with a standard 7-way RV trailer connector. Most trucks with factory tow packages already have the connector and wiring. A vehicle-specific adapter harness (sold separately) enables plug-and-play installation. Q: How do I set the gain properly?A: Start with gain at 0. Drive about 25 mph on a flat dry road. Apply the manual override lever fully — the trailer brakes should lock up just before you come to a complete stop. If they lock too early, reduce gain. If they don't lock, increase gain. The digital display shows your setting in real time. Q: Can I mount this anywhere in the vehicle?A: Yes, within 70 degrees of horizontal thanks to automatic leveling. The included bracket allows under-dash, on-dash, or custom mounting. For best ergonomics, mount where the manual override lever is easily accessible while driving. Q: What happens if the trailer disconnects?A: The 8508211 continuously monitors the brake connection. If lost, the display shows a diagnostic code (typically 'n.c.' for no connection). The controller won't apply brakes if no trailer is detected, preventing unnecessary electrical load. Q: Does this work with electric-over-hydraulic (EOH) brakes?A: This controller is designed for standard electric trailer brakes. For EOH systems, check with your trailer manufacturer for controller compatibility requirements, as some EOH systems need specific controllers. Package Includes 1 x iFJF 8508211 Trailer Brake Controller Kit, Proportional Electric Trailer Brake Controller, Digital LED Screen Display with 1-4 Axles | Installation hardware as shown | Product support documentation

Read more less

Product Overview The 8508211 Proportional Electronic Trailer Brake Controller Digital LED Screen Display with 2 to 8 Braking System is a premium-quality replacement part engineered to meet or exceed OEM specifications. Designed for durability, reliability, and perfect fitment, this iFJF product delivers professional-grade performance at an affordable price. Key Features Proportional Braking: Advanced proportional technology applies braking force based on deceleration rate for smooth, controlled stops. Digital LED Display: Clear LED screen shows real-time braking output and system status for easy monitoring. Universal Compatibility: Works with 2 to 8 brake systems, covering most trailers, campers, and RVs. Easy Installation: Plug-and-play design with mounting bracket and hardware included for quick setup. Durable Construction: Built with high-grade electronic components for reliable long-term performance. Compatibility & Fitment Designed as a direct replacement for the following applications. ⚠️ Always verify your equipment model, year, and specifications before ordering. Make Model Year Notes Universal Various — See product title for fitment Technical Specifications Specification Detail Brand iFJF Condition New Fitment Type Direct Replacement Part Number 8508211 Type Proportional Electronic Brake Systems 2-8 Why Choose iFJF? OEM-Grade Quality: Manufactured to strict tolerance standards for reliable performance Rigorous Testing: Every product undergoes quality inspection before shipping Fast Shipping: Orders processed within 1-2 business days from our US warehouses Expert Support: Technical assistance available for installation and troubleshooting Hassle-Free Returns: 30-day return policy for your peace of mind Installation Guide Mount the controller in an accessible location near the driver. Connect wiring harness to vehicle brake controller port or hardwire per included diagram. Secure all connections and test brake output with manual override. Calibrate by driving and braking normally. Fine-tune gain for your specific trailer weight. ⚠️ Professional installation recommended. Always test before towing. Frequently Asked Questions Q: Is this brake controller compatible with my vehicle?A: Yes, this proportional brake controller works with most vehicles that have a standard 7-pin trailer connector. It supports 2 to 8 brake systems and is compatible with electric and electric-over-hydraulic trailer brakes. Q: How do I calibrate the brake controller?A: Drive at approximately 25 mph on a flat surface and apply the manual override. Adjust gain until trailer brakes engage firmly without locking. The proportional sensor then automatically adjusts braking force during normal driving. Q: Does this work with electric-over-hydraulic brakes?A: Yes, this controller is compatible with both standard electric trailer brakes and electric-over-hydraulic systems. Select the appropriate mode during setup. Q: What's included in the package?A: The package includes the brake controller unit, mounting bracket, hardware kit, wiring harness, and installation manual. Q: What is the warranty period?A: iFJF offers a 12-month warranty against manufacturing defects. Contact our support team for warranty claims.

Read more less

Product Overview The 877LM 877MAX Keypad Opener For Liftmaster Sears Garage Door is a premium-quality replacement part engineered to meet or exceed OEM specifications. Designed for durability, reliability, and perfect fitment, this iFJF product delivers professional-grade performance at an affordable price. Key Features Security+ 2.0 Compatible: Works with Security+ 2.0 rolling code technology for enhanced security protection. Easy Programming: Simple setup — program in minutes with clear step-by-step instructions. Weather-Resistant Design: Built to withstand rain, sun, snow, and temperature extremes year-round. Wide Compatibility: Compatible with LiftMaster, Chamberlain, and Sears Craftsman openers (1993+). Backlit Keypad: Illuminated keys for easy use in low-light conditions. Compatibility & Fitment Designed as a direct replacement for the following applications. ⚠️ Always verify your equipment model, year, and specifications before ordering. Make Model Year Notes LiftMaster Various — Direct replacement Sears Various — Direct replacement Technical Specifications Specification Detail Brand iFJF Condition New Fitment Type Direct Replacement Part Number 877LM, 877MAX Type Wireless Keypad Technology Security+ 2.0 Why Choose iFJF? OEM-Grade Quality: Manufactured to strict tolerance standards for reliable performance Rigorous Testing: Every product undergoes quality inspection before shipping Fast Shipping: Orders processed within 1-2 business days from our US warehouses Expert Support: Technical assistance available for installation and troubleshooting Hassle-Free Returns: 30-day return policy for your peace of mind Frequently Asked Questions Q: Is this compatible with my garage door opener?A: Compatible with LiftMaster, Chamberlain, and Sears Craftsman openers manufactured after 1993 using Security+ or Security+ 2.0 technology. Check your opener's learn button color. Q: How do I program this keypad?A: Press and release the learn button on your garage door opener, then enter your desired 4-digit PIN on the keypad and press Enter within 30 seconds. The opener light will flash to confirm. Q: Is this keypad weatherproof?A: Yes, the keypad features a weather-resistant design with a protective slide cover to shield it from rain, sun, and snow. Q: Can I control multiple doors?A: Yes, you can program multiple opener codes to control up to 3 different garage doors or gates from this single keypad. Q: What battery does it use?A: The keypad uses a standard 9V battery (included), which typically lasts 1-2 years with normal use.

Read more less

Product Overview The 8838TM6 Universal Male Tank Sprayless Connector Contains 1/4"NPT with Thread Sealant Replacement for The Traditional Tank Fittings is a premium-quality replacement part engineered to meet or exceed OEM specifications. Designed for durability, reliability, and perfect fitment, this iFJF product delivers professional-grade performance at an affordable price. Key Features Sprayless Design: Prevents chemical spray-back during tank filling operations. Universal Compatibility: Fits standard 1/4" NPT male fittings. Thread Sealant Included: Pre-applied sealant for leak-free installation. Chemical-Resistant: Withstands agricultural chemicals and fertilizers. Easy Hand-Tightening: Ergonomic design for secure tool-free connection. Compatibility & Fitment Designed as a direct replacement for the following applications. ⚠️ Always verify your equipment model, year, and specifications before ordering. Make Model Year Notes Universal Various — See product title for fitment Technical Specifications Specification Detail Brand iFJF Condition New Fitment Type Direct Replacement Part Number 8838TM6 Type Sprayless Connector Thread 1/4" NPT Why Choose iFJF? OEM-Grade Quality: Manufactured to strict tolerance standards for reliable performance Rigorous Testing: Every product undergoes quality inspection before shipping Fast Shipping: Orders processed within 1-2 business days from our US warehouses Expert Support: Technical assistance available for installation and troubleshooting Hassle-Free Returns: 30-day return policy for your peace of mind Frequently Asked Questions Q: What is a sprayless connector?A: A specialized connector designed to prevent chemical splash-back when connecting to tank fill ports, protecting the operator during agricultural and industrial fluid transfer. Q: What size thread does it have?A: Features standard 1/4" NPT male thread for universal compatibility with most agricultural spray tanks. Q: Is thread sealant included?A: Yes, comes with pre-applied thread sealant for leak-free installation. Q: What chemicals is this resistant to?A: Constructed from chemical-resistant materials suitable for common agricultural chemicals, fertilizers, and pesticides. Q: Can I connect this without tools?A: Yes, the ergonomic design allows for hand-tightening. Use a wrench only for final snug if needed.

Read more less

iFJF 88624000 Pull-Down Spray Hose — Hansgrohe Kitchen Faucet Replacement When your Hansgrohe kitchen faucet spray head loses pressure, drips from the hose, or the hose shows signs of cracking and wear, don't replace the entire faucet — replace just the hose. The iFJF 88624000 pull-down spray hose is a direct replacement for Hansgrohe part numbers 88624000 and 95507000, restoring full water pressure and smooth spray head retraction. At a fraction of the OEM price, this hose gives your premium faucet a second life. Key Features & Benefits Direct Hansgrohe Replacement Compatible with all standard (non-Select) Hansgrohe pull-down kitchen faucets. The quick-connect fittings match the original exactly — no adapters, no leaks. Unscrew the old hose, click in the new one, and you're done in 10 minutes. Durable Braided Construction The hose features a reinforced braided nylon exterior over an inner tube rated for continuous hot and cold water use. The braided jacket resists kinking, abrasion, and the daily pull-down/push-up wear that eventually wears out factory hoses. 60-Inch Extended Reach At 60 inches, the hose provides ample length for filling pots, rinsing the sink, and cleaning around the kitchen. The weight-assisted retraction mechanism (reuse your existing weight) pulls the spray head smoothly back into the faucet spout. Technical Specifications Specification Detail Model iFJF 88624000 Replaces OEM Hansgrohe 88624000, 95507000 Length 60 inches Material Braided Nylon + Inner Tube Connection Quick-Connect / Threaded Compatibility Hansgrohe Standard Pull-Down Faucets Compatible Hansgrohe Faucet Lines Hansgrohe Allegro (standard, non-Select) Hansgrohe Talis (select models) Hansgrohe Metris (non-Select) Hansgrohe Focus (non-Select) Hansgrohe Cento Other standard Hansgrohe pull-down kitchen faucets Note: Does not fit Hansgrohe Select models with the button-controlled spray mode selector. Verify your faucet model before ordering. Installation Turn off water supply valves under the sink. Unscrew the spray head from the old hose. Pull the old hose out through the faucet spout. Disconnect the old hose from the supply line under the sink (quick-connect clip or threaded connection). Feed the new hose down through the faucet spout. Connect to the supply line fitting. Attach the spray head to the new hose. Reattach the weight (from the old hose) at the marked position. Turn water back on and test for leaks and smooth spray head operation. Frequently Asked Questions How do I know if this hose fits my Hansgrohe faucet? If your Hansgrohe faucet has a pull-down spray head (not a side spray) and is not a "Select" model with electronic spray mode switching, this hose will fit. The connecting fittings match the standard Hansgrohe quick-connect design used across most non-Select models. Does this hose include the spray head? No, this listing is for the replacement hose only. The spray head is sold separately if you need to replace that as well. Most Hansgrohe spray heads can be unscrewed and reattached to the new hose. Will this hose kink easily? The braided nylon jacket is specifically designed to resist kinking and tangling. The hose has enough flexibility to move freely inside the faucet body while maintaining full water flow even when pulled to its full 60-inch extension. Is this hose rated for hot water? Yes. The inner tube and braided jacket are rated for continuous use with water temperatures up to 160°F (71°C), making it suitable for standard kitchen hot water use. Related Products iFJF 88624000 Pull-Down Spray Hose Kitchen Parts Collection Faucet Parts Collection

Read more less

Product Overview The 893MAX G953EV-P2 Remote for LiftMaster Chamberlain Craftsman Garage Door Opener is a premium-quality replacement part engineered to meet or exceed OEM specifications. Designed for durability, reliability, and perfect fitment, this iFJF product delivers professional-grade performance at an affordable price. Key Features Security+ 2.0 Technology: Rolling code encryption prevents unauthorized access to your garage. Multi-Button Control: Control up to 3 garage doors or gate systems from a single remote. Long Range: Reliable operation up to 1,500 feet in open areas. Compact Design: Fits easily on your visor or keychain for convenient access. Easy Programming: Pairs with your opener in seconds using the learn button. Compatibility & Fitment Designed as a direct replacement for the following applications. ⚠️ Always verify your equipment model, year, and specifications before ordering. Make Model Year Notes LiftMaster Various — Direct replacement Chamberlain Various — Direct replacement Technical Specifications Specification Detail Brand iFJF Condition New Fitment Type Direct Replacement Part Number 893MAX, G953EV Type 3-Button Remote Technology Security+ 2.0 Why Choose iFJF? OEM-Grade Quality: Manufactured to strict tolerance standards for reliable performance Rigorous Testing: Every product undergoes quality inspection before shipping Fast Shipping: Orders processed within 1-2 business days from our US warehouses Expert Support: Technical assistance available for installation and troubleshooting Hassle-Free Returns: 30-day return policy for your peace of mind Frequently Asked Questions Q: Is this remote compatible with my opener?A: Compatible with LiftMaster, Chamberlain, and Sears Craftsman openers (1993+) with Security+ or Security+ 2.0 technology. Verify your opener's learn button color. Q: How do I program this remote?A: Press the learn button on your opener, then press and hold the desired button on the remote. The opener light will flash or you'll hear a click to confirm successful programming. Q: What is the range of this remote?A: Typical operating range is up to 1,500 feet in open areas. Range may vary based on local interference and building materials. Q: Can I program multiple doors?A: Yes, each button can be programmed to a different opener. Control up to 3 doors or gates from a single remote. Q: What battery does it use?A: The remote uses a CR2032 lithium coin battery (included). Battery life typically lasts 2-3 years.

Read more less

Product Overview The 8M0118177 892874T01 Fuel Pump Replacement for Mercury 30 40 50 60 HP Engine 4 Stroke Outboard is a premium-quality replacement part engineered to meet or exceed OEM specifications. Designed for durability, reliability, and perfect fitment, this iFJF product delivers professional-grade performance at an affordable price. Key Features Direct OEM Replacement: Engineered to exact specifications — no modifications required. Precision Fuel Delivery: Maintains correct fuel pressure for optimal engine performance. Marine-Grade Construction: Corrosion-resistant materials for harsh marine environments. Easy Installation: Drop-in replacement with all mounting points matching OEM. Quality Tested: Pressure-tested to ensure reliable operation out of the box. Compatibility & Fitment Designed as a direct replacement for the following applications. ⚠️ Always verify your equipment model, year, and specifications before ordering. Make Model Year Notes Mercury Various — Direct replacement Technical Specifications Specification Detail Brand iFJF Condition New Fitment Type Direct Replacement Part Number 8M0118177, 892874T01, 30 Type Electric Fuel Pump Application Marine Outboard Why Choose iFJF? OEM-Grade Quality: Manufactured to strict tolerance standards for reliable performance Rigorous Testing: Every product undergoes quality inspection before shipping Fast Shipping: Orders processed within 1-2 business days from our US warehouses Expert Support: Technical assistance available for installation and troubleshooting Hassle-Free Returns: 30-day return policy for your peace of mind Installation Guide Disconnect battery and relieve fuel system pressure. Remove old fuel pump assembly. Clean mounting surface thoroughly. Install new gasket and fuel pump, torque to OEM specs. Reconnect fuel lines and electrical connectors. Prime fuel system and check for leaks before starting. ⚠️ Professional installation recommended. Refer to service manual. Frequently Asked Questions Q: How do I know if my fuel pump needs replacement?A: Symptoms include: difficulty starting, engine sputtering at high speeds, loss of power under load, decreased fuel efficiency, and whining noise from the fuel tank. Q: Is this a direct bolt-on replacement?A: Yes, this fuel pump is engineered as a direct OEM replacement with matching mounting points, electrical connectors, and fuel line fittings. Q: Should I replace the fuel filter at the same time?A: Yes, we strongly recommend replacing the fuel filter when replacing the fuel pump. A clogged filter can cause premature pump failure. Q: What's included in the kit?A: The kit includes the fuel pump assembly with gaskets and O-rings. Some applications may require a separate fuel pump strainer. Q: Can I install this myself?A: Installation requires mechanical experience. Professional installation is recommended for most marine and automotive applications.

Read more less