Products

Valve Seat Removal Tool for Symmons Temptrol TA10 TA4 T-35 — with Stem Seat Washer The Valve Seat Removal Tool is a specialized plumbing tool designed for Symmons Temptrol shower valves (models TA10, TA4, and T-35 A/B). When your Temptrol valve starts dripping, the culprit is almost always a worn seat and washer — and getting the old seat out without the right tool can turn a simple repair into a plumbing nightmare. This tool grips and extracts the valve seat cleanly, without damaging the valve body threads. Key Features Precision-Machined Splines: Hardened steel splines match Symmons seat geometry exactly — no slipping, no stripping. Complete Kit: Includes the removal tool plus replacement stem seat washers so you can complete the repair in one job. Ergonomic T-Handle: Comfortable grip provides the leverage needed to break free seats that have been in place for decades. Corrosion-Resistant Finish: Chrome-plated tool body resists rust even in wet plumbing environments. Professional Grade: Built for plumbers who use this tool daily — not a one-and-done disposable. Compatibility Brand Model Valve Type Symmons Temptrol TA10 Pressure-balancing shower valve Symmons Temptrol TA4 Standard shower valve Symmons T-35 A/B Tub/shower valve Frequently Asked Questions Q: How do I know if my Temptrol valve needs a new seat?A: If your shower drips constantly even when the handle is fully off, or if you feel water temperature fluctuations during use, the seat and washer are the most likely cause. Symmons Temptrol valves typically need seat replacement every 5-8 years. Q: Can I use a regular wrench instead of this tool?A: We strongly advise against it. The Symmons seat uses a specific spline pattern. Using pliers or a generic wrench risks stripping the seat, damaging valve body threads, or leaving pieces of the old seat inside the valve — turning a $30 repair into a $500+ valve replacement. Q: Does this come with instructions?A: The tool is intuitive for experienced DIYers. For step-by-step guidance, see our installation guide linked below. Key tip: always shut off the water supply before starting!Related Guides & Articles📖 How to Replace a Symmons Temptrol Valve Seat: Step-by-Step DIY

Read more less

Keep Your Best Friend Safe on Every Adventure The iFJF Vehicle Rear Seat Isolation Barrier Net is the must-have accessory for Jeep Wrangler owners who travel with their dogs. This heavy-duty pet divider creates a secure barrier between the cargo area and passenger cabin, protecting both your pet and your Wrangler's interior. Key Features Universal JK JL Fitment: Precisely designed for 2007-2021 Jeep Wrangler JK and JL Unlimited 4-door models. Compatible with both hardtop and soft top. Heavy-Duty Nylon Mesh: Durable, tear-resistant netting withstands even energetic dogs. Breathable material ensures proper airflow and visibility. Quick & Easy Installation: No drilling required. Attaches securely to factory grab handles, roll bar, and rear seat mounts with adjustable straps and heavy-duty buckles in under 10 minutes. Full-Width Coverage: Floor-to-ceiling barrier blocks access to the front cabin while allowing full use of cargo space. Safety Certified: Crash-test tested under simulated frontal collision at 30 mph. Contains dogs up to 80 lbs during emergency braking. Compatibility Make Model Year Range Trim Jeep Wrangler JK 2007-2018 Unlimited 4-Door Jeep Wrangler JL 2018-2021 Unlimited 4-Door Why Choose iFJF Pet Barrier? ✅ Distraction-Free Driving: Prevents your dog from jumping into the front seat — a major safety hazard on and off-road. ✅ Interior Protection: Keeps muddy paws, shedding fur, and slobber confined to the cargo area. ✅ Off-Road Ready: Extra-secure mounting stays in place during intense trail crawling and rough terrain. ✅ Lifetime Warranty: Backed by iFJF's satisfaction guarantee. Specifications Spec Detail Material Heavy-Duty Nylon Mesh Installation No-drill, tool-free, <10 min Fitment 2007-2021 Wrangler JK/JL Unlimited Frequently Asked Questions Q: Will this fit a 2-door Wrangler?A: This barrier is optimized for 4-door Unlimited models (JKU/JLU). It may fit 2-door models with some adjustment. Q: Can I use this with a soft top?A: Yes. Mounting points attach to the roll bar structure, identical on hardtop and soft top Wranglers. Q: How does the mesh hold up against chewing?A: The nylon mesh is tear-resistant but not chew-proof. For aggressive chewers, pair with a crate. Q: Will this fit my 2020 JL with factory subwoofer?A: Yes. The barrier mounts above cargo floor level and doesn't interfere with the factory subwoofer. Q: Is this crash-tested?A: Tested under simulated frontal collision at 30 mph. Designed for medium-to-large dogs up to 80 lbs. Q: Can I leave it installed permanently?A: Absolutely. Breathable mesh doesn't obstruct visibility. Many owners keep it as a cargo divider. 📚 Related Guides & Articles 📖 Best Jeep Wrangler JK/JL Accessories for Pet Owners

Read more less

W 719/45 Spin-On Oil Filter — Premium Filtration for VAG 2.0L TSI/TFSI Engines The iFJF W 719/45 Spin-On Oil Filter is a direct OEM-spec replacement for the 2.0L turbocharged engines found in Audi and Volkswagen vehicles from 2008-2019. Engineered to meet the stringent filtration requirements of direct-injection TSI/TFSI engines, this filter helps protect your turbocharger and engine bearings from oil contamination. Key Features OEM Cross Reference: Replaces 06J 115 561B, W 719/45, and equivalent Mann/Mahle filters. High-Efficiency Media: Multi-layer synthetic blend media captures particles down to 20 microns while maintaining full oil flow during cold starts. Silicone Anti-Drain Back Valve: Prevents dry starts by keeping oil in the filter when the engine is off — critical for turbocharger longevity. Bypass Valve: Integrated pressure relief ensures oil still reaches bearings if the filter becomes clogged. Spin-On Design: Tool-free hand installation — simple DIY oil change in under 30 minutes. Vehicle Compatibility Make Model Year Range Engine Audi A3 (8P/8V) 2008-2013 2.0L TFSI/TSI Audi A4 (B8) 2009-2016 2.0L TFSI Audi A5 (8T) 2010-2014 2.0L TFSI Audi Q3 (8U) 2015-2019 2.0L TFSI Audi TT (8J) 2009 2.0L TFSI VW Beetle, Jetta, Passat 2008-2019 2.0L TSI Why Oil Filtration Matters for TSI/TFSI Engines VAG's 2.0L TSI/TFSI is a high-output turbocharged direct-injection engine. The turbocharger spins at up to 200,000 RPM and relies on clean, pressurized oil for both lubrication and cooling. A clogged or low-quality oil filter starves the turbo of oil, leading to bearing failure — a $1,500+ repair. Our W 719/45 filter provides the consistent oil flow and filtration these engines demand. Frequently Asked Questions Q: Will this fit my 2012 Audi A4 2.0T?A: Yes! The W 719/45 is the correct filter for all B8 Audi A4 models with the 2.0L TFSI engine from 2009-2016. Q: Is this the same as the dealership filter?A: It meets or exceeds the same specifications (VW 502 00/505 00) as the OEM 06J 115 561B filter, at a fraction of the dealership price. Q: How often should I change the oil and filter?A: VW/Audi recommends every 10,000 miles or 12 months. We recommend every 5,000-7,500 miles for tuned or aggressively driven vehicles. Q: Does this have the anti-drain back valve?A: Yes. The silicone anti-drain back valve prevents oil from draining out of the filter when the engine is off, ensuring immediate oil pressure on startup.

Read more less

Fix ALL Your Refrigerator LED Lights in One Go If your Whirlpool or KitchenAid refrigerator has dark sections — main light out while side lights work, or vice versa — you need this complete 3-piece LED driver set. Most Whirlpool-family refrigerators with LED lighting use two different driver modules: W10515057 for the side lights and W10515058 for the main overhead light. Replace all of them at once and restore full illumination to your entire refrigerator. What's Included 2 × W10515057 Side Light Driver — Powers the LED strips on the sides of the fresh food compartment 1 × W10515058 Main Light Driver — Powers the primary overhead LED light Symptoms This Kit Fixes Main light out, side lights working — Failed W10515058 driver Side lights out, main light working — Failed W10515057 driver(s) All lights dim or flickering — Multiple aging drivers Intermittent lighting — Drivers failing under heat load Complete darkness — All drivers failed simultaneously (common after power surge) Compatibility Brand Refrigerator Type Models Whirlpool Side-by-side, French door, bottom-freezer Models with dual LED lighting zones (2010-2020) KitchenAid Side-by-side, French door Models with multi-zone LED interior lighting Maytag Side-by-side, French door Models with LED lighting systems Amana Side-by-side Select models with LED interior lights JennAir Built-in, freestanding Models with LED interior lighting systems Replaces Part Numbers: W10515057, W10515058, W10398007, PS11755866, AP6022533 Specifications Specification Detail Kit Contents 2 × W10515057 (side) + 1 × W10515058 (main) LED drivers Connector Type OEM-style plug-and-play — no cutting or soldering Input 120V AC from refrigerator control board Installation 15-20 minutes — tool-free on most models Testing Each driver individually tested for stable LED current output Why Replace All Drivers at Once? LED drivers in refrigerators age at similar rates. If one has already failed, the others are close behind. Replacing all drivers at the same time saves you from having to tear into your refrigerator again in a few months when the next one fails. Why Choose iFJF? Complete set — All three drivers in one purchase. No need to order separately Cost-effective — Bundle pricing saves money vs buying individual drivers One repair, all lights fixed — Don't come back to a dark fridge in 3 months Tested and matched — All drivers are pre-tested for stable, flicker-free output Simple install — Pop off the light cover, swap the driver, snap the cover back on Frequently Asked Questions Q: How do I know if I need the 3-piece set or just one driver?A: If only your side lights are out, you may just need W10515057. If only the main overhead light is out, you may just need W10515058. But if your fridge is more than 5 years old and one driver has failed, we recommend replacing all three — the others are likely near end-of-life. Q: Does this fit my Whirlpool side-by-side?A: Most Whirlpool side-by-side refrigerators manufactured between 2010-2020 with LED lighting use these exact driver modules. Check the part number on your existing driver to confirm: W10515057 or W10515058 should be printed on the module. Q: Are these genuine OEM Whirlpool parts?A: These are premium aftermarket replacements manufactured to OEM specifications. They provide identical voltage and current output to the original Whirlpool/KitchenAid drivers. Q: Is installation really tool-free?A: On most models, yes. The light panel cover snaps off, the driver unplugs, you plug in the new one, and snap the cover back. No screwdrivers, no wire stripping, no electrical work required. Q: What if the new driver doesn't fix my lights?A: If replacing the driver doesn't restore your lights, the issue may be with the main control board or the LED strip itself. However, the driver is the failure point in 90%+ of cases.

Read more less

Fix Your Refrigerator LED Lights — Simple Driver Replacement Are your refrigerator lights dimming, flickering, or not working at all? The LED driver module is the most common failure point in modern Whirlpool, KitchenAid, Maytag, and Amana refrigerators. Our W10515057 replacement LED light driver restores full brightness to your fridge and freezer lights in minutes — no tools, no wiring, just plug and play. Symptoms of a Failed LED Driver Lights won't turn on — Most common symptom of driver failure Flickering or pulsing — Driver can't maintain stable voltage to LEDs Dim lighting — LEDs are working but at reduced brightness Intermittent operation — Lights work sometimes, then go dark One section dark — Side lights work but main light doesn't (or vice versa) Compatibility — Fits These Brands Brand Models Whirlpool Side-by-side, French door, and bottom-freezer refrigerators with LED lighting (2010-2020) KitchenAid Side-by-side and French door models with LED interior lighting Maytag Side-by-side and French door refrigerators with LED lighting Amana Select side-by-side refrigerator models with LED lights JennAir Built-in and freestanding refrigerators with LED interior lighting Replaces Part Numbers: W10515057, W10398007, PS11755866, AP6022533, W10515058 Specifications Specification Detail Type LED constant-current driver module Input 120V AC from refrigerator main board Output Constant DC current for LED arrays Connector Plug-and-play OEM-style connector — no cutting or soldering Installation 5-10 minutes — completely tool-free on most models Installation — No Tools Needed Unplug the refrigerator or turn off the circuit breaker Locate the LED driver — usually behind the light panel at the top of the fresh food section or behind the control panel Disconnect the old driver — unplug the wire connectors (note their positions) Connect the new driver — plug the connectors into the matching ports Restore power and test — lights should illuminate at full brightness Why Choose iFJF? Exact replacement — Same form factor, connectors, and output as the OEM W10515057 Plug-and-play — No cutting, splicing, or soldering required Restores full brightness — Eliminates dim, flickering, or completely dark lights Tested output — Each driver is tested for stable LED current output Fast fix — Have your fridge lights working again in 10 minutes Frequently Asked Questions Q: How do I know if I need the driver or the LED boards themselves?A: If ALL lights are dim or not working, it's almost always the driver. If only one specific LED is out while others work, that individual LED board may be the issue. The driver is the most common failure point. Q: Does this replace W10515058 as well?A: W10515058 is the main light driver, while W10515057 typically drives the side lights. Some refrigerators use one or both. Check your refrigerator's parts diagram to confirm which driver(s) you need. Q: Is this an OEM Whirlpool part?A: This is an OEM-quality aftermarket replacement that meets or exceeds the specifications of the original W10515057 driver. It provides identical performance at a lower price. Q: Will this work with my KitchenAid French door refrigerator?A: Yes, if your KitchenAid refrigerator uses the W10515057 or W10398007 driver module. Most KitchenAid French door and side-by-side models from 2010-2020 with LED lighting use this driver. Q: My fridge lights are completely dead — will this fix it?A: In most cases, yes. The LED driver is the #1 cause of completely dead refrigerator lights. If replacing the driver doesn't fix the issue, the main control board may have failed — but that's much less common.

Read more less

Monitor Your Diesel Fuel Quality with iFJF Water in Fuel Sensor Water contamination in diesel fuel is a silent engine killer. Without a functioning water-in-fuel (WiF) sensor, you may not know that water has accumulated in your fuel system until expensive injector or pump damage has already occurred. The iFJF 904-438 Water in Fuel Sensor is a direct OEM-spec replacement that restores your vehicle's ability to detect water in the fuel supply and alert you through the dashboard warning light before damage happens. This sensor is compatible with 2011-2016 F-250, F-350, F-450, and F-550 Super Duty trucks equipped with the 6.7L Power Stroke diesel engine. It replaces part numbers 904-438, OEM BC3Z-9T321-A, and BC3Z9T321B. Made of premium materials that are extensively tested and durable, each package includes 1 water in fuel sensor. Important: The Water in Fuel sensor lets the Engine Control Unit (ECU) and/or dashboard lamp indicator know when water detection has occurred in the vehicle's fuel supply, helping you avoid extensive damage to the fuel system. If your "Water in Fuel" warning light stays on or fails to illuminate during self-test, your sensor may need replacement. Key Features Exact OEM Replacement: Manufactured to match the fit, form, and function of the Ford factory sensor. Replaces part number 904-438 and OEM numbers BC3Z-9T321-A and BC3Z9T321B without modifications. Critical ECU Communication: Lets the Engine Control Unit (ECU) and/or dashboard lamp indicator know when water detection has occurred in the vehicle's fuel supply to avoid extensive damage to the fuel system. Triggers the "Water in Fuel" warning light on your instrument cluster. Premium Quality Construction: Made of premium materials that are extensively tested for durability and reliability. Resistant to diesel fuel, biodiesel blends, and under-hood environmental conditions. Accurate Water Detection: Uses precision conductivity sensing to detect even small amounts of accumulated water at the bottom of the fuel filter housing where water naturally settles. Plug-and-Play Installation: Direct drop-in replacement for the factory sensor. Plugs into the existing wiring harness connector without splicing or modification. Prevents Costly Repairs: Early warning of water contamination helps you drain the separator before water reaches the high-pressure fuel pump and injectors—saving thousands in potential repair costs. Technical Specifications Specification Detail Product Type Water in Fuel (WiF) Sensor Part Number 904-438 OEM Numbers BC3Z-9T321-A, BC3Z9T321B Material Premium-Grade Materials, Extensively Tested Package Contents 1 x Water in Fuel Sensor Brand iFJF Vehicle Compatibility Year Make Model Engine 2011 – 2016 Ford F-250 Super Duty 6.7L Power Stroke Diesel 2011 – 2016 Ford F-350 Super Duty 6.7L Power Stroke Diesel 2011 – 2016 Ford F-450 Super Duty 6.7L Power Stroke Diesel 2011 – 2016 Ford F-550 Super Duty 6.7L Power Stroke Diesel Compatible with 2011-2016 Ford Super Duty trucks equipped with the 6.7L Power Stroke diesel engine. Verifies water detection in the primary fuel filter/water separator housing located on the frame rail under the driver's side. Always confirm your existing sensor part number before ordering. When to Replace Your WiF Sensor Constant Warning Light: The "Water in Fuel" light stays illuminated even after draining the separator and verifying fuel quality. No Self-Test: The warning light does not illuminate briefly during the key-on bulb check, indicating a faulty sensor or circuit. Intermittent Alerts: The warning light flickers or triggers randomly despite no water being present in the fuel system. Corrosion or Damage: Physical inspection reveals corrosion on the sensor probe, cracked housing, or damaged wiring connector. Preventative Maintenance: As part of a fuel system service when replacing the fuel filter and draining the water separator. Installation Tips Locate the fuel/water separator housing on the driver's side frame rail under the vehicle. Place a drain pan beneath the housing to catch any spilled fuel. Disconnect the electrical connector from the existing sensor by pressing the release tab. Unscrew and remove the old sensor from the bottom of the filter housing. Inspect the O-ring sealing surface on the housing for debris or damage; clean if necessary. Thread the new iFJF 904-438 sensor into the housing by hand to avoid cross-threading, then snug it gently—do not overtighten. Reconnect the electrical connector until it clicks into place. Turn the ignition to the ON position (without starting) and verify the "Water in Fuel" light briefly illuminates during the self-test. Frequently Asked Questions Why does my "Water in Fuel" light stay on even after draining the separator? If the light remains on after properly draining the water separator and confirming the fuel is clean, the sensor itself is likely faulty. The sensor probe may be coated with contaminants, corroded, or the internal electronics may have failed. Replacing the sensor with the iFJF 904-438 should resolve the issue. Will this fit my 2013 Ford F-350 6.7L Power Stroke? Yes, this sensor is a direct fit for all 2011-2016 Ford F-250, F-350, F-450, and F-550 Super Duty trucks equipped with the 6.7L Power Stroke diesel engine. It replaces Ford part numbers BC3Z-9T321-A and BC3Z9T321B. Can I drive with the Water in Fuel light on? It is not recommended. While the sensor itself being faulty does not immediately damage the engine, the light may also indicate actual water in your fuel system. Driving with water-contaminated fuel can destroy high-pressure injectors and the CP4 fuel pump—repairs exceeding $8,000-$12,000. Always drain the separator first; if the light persists, replace the sensor. How often should I drain the water separator? Ford recommends draining the diesel fuel conditioner module (DFCM) water separator monthly or at every oil change interval. More frequent draining is advisable if you fuel up at high-turnover stations in humid regions or use biodiesel blends, which tend to hold more suspended water. Related Power Stroke Parts FL2051S Oil Filter2011-2020 6.7L Power Stroke FD4615 Fuel Filter Combo2017-2019 6.7L 6.0L WIF Sensor2003-2007 6.0L Power Stroke

Read more less

385311641 Water Valve Kit — Fix RV Toilet Leaks & Weak Flushes The iFJF 385311641 Water Valve Kit is a complete replacement flush water valve assembly for Sealand 300, 310, and 320 series RV toilets. If your toilet is leaking water around the pedal area, flushing weakly, or failing to fill the bowl properly, this kit restores full function with all gaskets, seals, and mounting hardware included. Key Features Complete Assembly: Water valve, gaskets, seals, and screws included Precision Fit: Designed for Sealand 300/310/320 and Dometic pedal-flush toilets Leak-Free: Fresh EPDM seals ensure water-tight operation Quick Install: 15-20 minute DIY job from behind the toilet Corrosion Resistant: Brass valve core with UV-stabilized plastic housing Compatibility Brand Series Notes Sealand / Dometic 300 Series All height variants Sealand / Dometic 310 Series Ceramic & plastic bowl Sealand / Dometic 320 Series Elongated bowl Dometic Vacuflush Select models Product Specifications Specification Detail Brand iFJF SKU FJ-WVK01-WH Price $19.99 Category RV Toilet Parts Condition New Warranty 30-Day Satisfaction Guarantee Why Choose iFJF? At iFJF Direct, we supply premium replacement parts backed by responsive US-based customer support. Every product is manufactured to meet or exceed OEM specifications, giving you factory-quality performance at a better value. Fast shipping from our US warehouses gets your order to you quickly. Need help with fitment? Contact our team — we are here to help you get the right part the first time. Frequently Asked Questions Q: My toilet is leaking from the pedal area. Is this the right part?A: Yes. Water leaking around the flush pedal is the number one symptom of a failed water valve. This kit replaces the entire valve assembly. Q: Does this fit the Sealand 320 elongated bowl?A: Yes, it is compatible with the 320 series elongated bowl toilets plus the 300 and 310 standard bowls. Q: What is included in the kit?A: Water valve body, all internal seals and gaskets, mounting bracket, and screws. Q: How long does installation take?A: Most RV owners complete this repair in 15-20 minutes with basic tools. Related Products iFJF 385236096 Spring Cartridge Kit iFJF 385318162 Flush Ball & Shaft Kit

Read more less

Water-in-Fuel Sensor for 2003-2007 Ford 6.0L Power Stroke Diesel The iFJF Water-in-Fuel (WIF) Sensor is a direct OEM replacement for the notoriously failure-prone sensor on 2003-2007 Ford 6.0L Power Stroke engines. When your WIF light stays on even after draining the HFCM, chances are the sensor itself has failed — and this is the fix you need. Key Features Direct OEM Replacement: Replaces 6C3Z-9C264-A, 904-459, FWSS114 — exact fit for the HFCM (Horizontal Fuel Conditioning Module) on 6.0L Power Stroke engines. Plug-and-Play: 5-minute driveway installation. Unplug the old sensor, unscrew it, thread in the new one, reconnect the harness. Stops False Alerts: If your "Water in Fuel" light is on but you've already drained the HFCM and found no water, a failed sensor is the culprit. This replacement resolves the issue. Corrosion-Resistant: Sealed electronics prevent the internal corrosion that causes OEM sensors to fail after years of diesel fuel exposure. Vehicle Compatibility Make Model Year Range Engine Ford F-250 / F-350 / F-450 / F-550 Super Duty 2003-2007 6.0L Power Stroke V8 Ford E-350 / E-450 Super Duty 2003-2007 6.0L Power Stroke V8 Ford Excursion 2003-2005 6.0L Power Stroke V8 Symptoms of a Failed WIF Sensor "Water in Fuel" warning light stays on after draining the HFCM separator No water found in drained fuel, but light persists Intermittent WIF light that comes and goes randomly Engine enters reduced power/limp mode due to false water detection signal Installation Instructions Locate the HFCM on the driver-side frame rail under the cab. Unplug the electrical connector from the WIF sensor (the sensor on the bottom/side of the HFCM). Using an appropriate wrench, unscrew the old sensor counterclockwise. Have a small container ready — a small amount of diesel will drip out. Clean the sensor port threads on the HFCM housing. Thread the new sensor in by hand to avoid cross-threading, then tighten snugly with a wrench. Do NOT overtighten. Reconnect the electrical harness. Cycle the key ON (not start) — the WIF light should go out. If it doesn't, drain the HFCM to ensure there's no actual water present. Frequently Asked Questions Q: My WIF light is on but I drained the HFCM and found no water. Will this fix it?A: Most likely yes! The 6.0L WIF sensor is known to fail internally, causing a persistent false warning. This replacement sensor resolves the issue in 90%+ of cases. Q: Is this the same sensor used on the 6.4L Power Stroke?A: No. The 6.4L (2008-2010) uses a different WIF sensor design. This sensor is specifically for 2003-2007 6.0L engines. Q: Do I need to prime the fuel system after replacing the sensor?A: No. Replacing the WIF sensor does not introduce air into the fuel system. Simply install and go. Q: Will driving with the WIF light on damage my engine?A: If the light is due to a failed sensor (no actual water), it's safe to drive. However, the PCM may trigger reduced power mode, so we recommend replacing the sensor promptly.

Read more less

Product Overview The iFJF 18990035 Weber 44 IDF carburetor is a premium replacement for 1968-1979 Volkswagen Beetle, Super Beetle, and Transporter (Bus) models with the 1.6L air-cooled engine. Featuring dual 44mm throttle bores, this 2-barrel downdraft carburetor delivers significantly improved throttle response, horsepower, and tunability compared to the stock Solex carburetor. Complete with integrated air horn and striking golden finish. Key Features 44mm Dual Throttle Bores — 44mm barrels provide ample airflow for modified 1600cc engines, including those with bigger camshafts, ported heads, or increased displacement (1776cc, 1915cc). Direct Solex Replacement — Same downdraft configuration as the factory Solex 34 PICT carburetor. Bolts to the stock intake manifold center section. Complete Assembly with Air Horn — Includes integrated air horn for cleaner intake airflow and better filtration mounting. Genuine Weber IDF Design — Based on the legendary Weber IDF circuit with tunable idle jets, main jets, air correction jets, and emulsion tubes — giving you full control over fuel calibration. Golden Finish — Corrosion-resistant golden chromate coating that looks as good as it performs. Tunable Accelerator Pump — Adjustable pump stroke for customizing tip-in fuel delivery. Compatibility Year Model Engine 1968-1979 VW Beetle (Type 1) 1.6L 1584cc H4 1971-1979 VW Super Beetle 1.6L 1584cc H4 1968-1971 VW Transporter Type 2 (211/215/261/265) 1.6L 1584cc H4 1968-1974 VW Karmann Ghia 1.6L 1584cc H4 1968-1973 VW Type 3 (Fastback/Squareback) 1.6L 1584cc H4 (center mount only) Specifications Parameter Value OEM Part Numbers 18990035, 18990030, 18990.035V Carburetor Type 2-Barrel Downdraft (Weber IDF) Throttle Bore 44mm (x2) Venturi Size 36mm Mounting Pattern Standard IDF/Centro-Mount Choke None (performance carburetor) Fuel Inlet M10x1.0 Banjo Fitting Why Upgrade to Weber IDF? The factory Solex 34 PICT-3 carburetor was adequate when new but is now notorious for warped throttle bodies, clogged idle circuits, and difficult cold starts. The Weber IDF design has been the gold standard for air-cooled VW performance since the 1970s. It offers superior tunability with replaceable jets, a more robust accelerator pump circuit, and dramatically improved throttle response. Whether you're restoring a daily driver or building a weekend cruiser, this carburetor transforms how your vintage VW drives. Installation Tips Use new paper gaskets on both sides of the phenolic spacer block Set idle mixture screws at 1 turn out from seated as starting point Verify fuel pressure at 2.5-3.0 PSI — mechanical pumps may need a regulator Base idle speed: 850-900 RPM on air-cooled engines Check for vacuum leaks at intake boots and manifold end castings before tuning With a 009 mechanical advance distributor, set timing to 28-32° BTDC at 3000+ RPM Frequently Asked Questions Q: Will this fit my 1974 Super Beetle with stock engine?A: Yes. The 18990035 Weber 44 IDF is a direct bolt-on replacement for the stock Solex carburetor on your 1974 Super Beetle 1600cc. It bolts to the factory intake manifold center section. Q: Do I need to change my distributor when installing this carburetor?A: The Weber 44 IDF works well with both vacuum-advance (SVDA) and centrifugal-advance (009) distributors. If using a 009, make sure the vacuum port on the carb is capped. Q: Is this carburetor too big for a stock 1600cc engine?A: The 44 IDF is properly sized for stock to mild 1600cc engines when properly jetted. It comes pre-calibrated for 1600cc. If upgrading to 1776cc or larger, you may want to increase main jet sizes. Q: What air filter fits on this carburetor?A: The integrated air horn accepts standard IDF-style air filter assemblies. Low-profile oval filters (commonly available for Beetle engine bays) fit perfectly. Q: Does this carburetor work with dual carb setups?A: This carburetor is designed for single center-mount applications. For dual carb setups, consider dual 40 IDF or 44 IDF kits with appropriate manifolds. Q: Will I need to re-jet for my elevation?A: At elevations above 4,000 ft, you may want to reduce main jet size by 5-10 numbers. Below 4,000 ft, the factory jetting will work well.

Read more less

Product Overview WFCO WF-8955 MBA RV Converter Main Board 55 Amp - Direct Replacement. Engineered for reliable performance and precision fitment, this iFJF aftermarket part meets or exceeds OEM specifications for durability and function. Ideal for DIY mechanics and professional technicians alike. Key Features Direct Replacement Board: Exact match for WFCO WF-8955 MBA converter main board — no rewiring needed. 55 Amp Output: Reliable power conversion from 120V AC shore power to 12V DC for all RV systems. Smart Charging: Multi-stage battery charging protects your RV battery from overcharging. Built-in Protection: Overload, short circuit, and thermal protection for worry-free operation. Compatibility Year Make Model Engine/Notes See Description WFCO WF-8955 MBA RV Converter Main Board 55 Amp - Direct Fit ⚠️ Always verify fitment with your specific vehicle year, make, model, and engine before ordering. Contact our support team for compatibility questions. Specifications Specification Value Brand iFJF Product Type RV Electrical SKU FJ-JP-X-CB03 Price $167.99 USD Output 55 Amp / 12V DC Input 120V AC Why Choose iFJF? Quality Assurance: Every iFJF part undergoes rigorous quality inspection before shipping. Precision Engineering: Manufactured to tight tolerances for guaranteed fitment. Expert Support: Our team of diesel and automotive specialists is ready to help with any questions. Fast Shipping: Orders ship within 1-2 business days from our US warehouses. Frequently Asked Questions Q: Is this a direct replacement for the WFCO WF-8955?A: Yes. This is the main converter board for the WFCO WF-8955 MBA (Model with Built-in Accessories) power center. It replaces the original board without any wiring modifications. Q: What are symptoms of a failed RV converter?A: Common signs include: 12V lights dimming or flickering, battery not charging on shore power, buzzing or humming from the converter, circuit breakers tripping, and burning smell from the power center. Test output voltage — should be 13.2-14.4V DC. Q: Can I install this myself?A: Yes, if you're comfortable with basic electrical work. Disconnect all power (shore power AND battery), remove the converter cover, unplug the old board, swap in the new one, and reconnect. Always double-check connections before restoring power. Order your WFCO WF-8955 MBA RV Converter Main Board 55 Amp - today — fast shipping, expert support, and the quality you can trust from iFJF Direct. 📖 Related Guides & Articles 🔗 RV Generator Fuel Filter Replacement: Two Expert Methods Compared 🔗 RV Awning Sun Shade Review: iFJF 9'x7' Black Mesh Screen 🔍 Explore More Parts Looking for compatible parts? Browse our full selection of RV Parts & Accessories for your vehicle or equipment. iFJF Direct offers quality aftermarket parts with fast shipping. Related Guide Read: WFCO WF-8955 MBA RV Converter Board Replacement: Fix Dead Batteries and Flickering Lights in an Hour 📖 Related Guide: WFCO WF-8955 MBA Converter Board: Troubleshooting & Install Guide →

Read more less

Product Overview Complete diving board mounting bolt kit for two-hole residential pool diving boards. DB-TB-M compatible kit includes marine-grade 304 stainless steel bolts, nylon lock nuts, heavy-duty flat washers, and UV-resistant white bolt covers. Engineered for continuous pool chemical exposure, intense UV, and dynamic diving board loads season after season. Key Features Marine-Grade 304 Stainless — Bolts, lock nuts, and washers resist chlorine, salt, and chemical corrosion for permanent underwater installation. UV-Resistant White Covers — Molded polymer bolt covers maintain bright white appearance without yellowing or cracking in sunlight. Complete All-Inclusive Kit — Everything needed: 2 bolts, 2 lock nuts, 4 washers, 2 decorative covers. No separate hardware store trips. Two-Hole Board Compatible — Standard two-hole residential pattern fits SR Smith, Inter-Fab, and most aftermarket diving boards. Easy DIY Installation — All hardware included with instructions. Typical installation 30–45 minutes with basic socket set. Compatibility Make Model Year Range Notes Universal Two-Hole Residential Diving Boards Standard 6"/8"/10" Board Sizes SR Smith Residential Diving Boards All Models Two-Hole Mount Pattern Inter-Fab Residential Diving Boards All Models Two-Hole Mount Pattern Specifications Specification Value Bolt & Nut Material 304 Marine-Grade Stainless Steel Cover Material UV-Resistant Molded Polymer Cover Color White Mounting Pattern Two-Hole Standard (Residential) Kit Contents 2 Bolts + 2 Lock Nuts + 4 Washers + 2 Covers Frequently Asked Questions Q: What's included in the kit?A: Two 304 SS mounting bolts, two nylon lock nuts, four flat washers, and two white decorative bolt covers — everything for one board. Q: Will this fit my diving board?A: Fits standard two-hole residential boards from SR Smith, Inter-Fab, and most brands. Contact us with your board specs if unsure. Q: Will the hardware rust?A: No. 304 marine-grade stainless steel is specifically chosen for continuous pool water and chemical exposure. Q: How do I install it?A: Remove old hardware, align board, insert bolts from top, secure with washers and lock nuts below, snap on covers. 30–45 minutes. Q: When should I replace mounting hardware?A: Replace if you see rust, pitting, or corrosion — or if the board feels loose. Annual safety inspection recommended. Related Products Complete pool setup: Pool Filter Manual Air Relief Valve for Hayward filters, Diving Board Tread Replacement for grip safety, Pool Ladder Bumpers for wall protection.

Read more less

Windshield Washer Fluid Reservoir Cap for Jeep Wrangler JK, JL & Gladiator JT Replace your missing, cracked, or loose-fitting windshield washer fluid reservoir cap with this direct OEM replacement. Fits 2007-2018 Jeep Wrangler JK/JKU, 2018-2023 Jeep Wrangler JL/JLU, and 2020-2023 Jeep Gladiator JT models. A proper seal on your washer reservoir prevents fluid evaporation, keeps debris out of the system, and ensures your washer pump operates at full pressure when you need it most — whether clearing mud from a trail run or salt spray from winter driving. Key Features Direct OEM Replacement: Manufactured to match the original factory cap dimensions exactly — same snap-fit retention, same vent design, same sealing performance Secure Snap-Fit Design: Audible click confirms proper installation — won't vibrate loose on rough trails or at highway speeds UV-Resistant Polypropylene: Durable plastic construction resists cracking, fading, and warping from engine bay heat and direct sun exposure Proper Venting: Integrated vent prevents vacuum lock in the reservoir while keeping dirt, dust, and moisture out Universal JK/JL/JT Fit: One cap fits all 2007-2023 Jeep Wrangler and 2020-2023 Gladiator models — no need to worry about model year variations Compatibility Year Range Make Model 2007-2018 Jeep Wrangler JK / JKU 2018-2023 Jeep Wrangler JL / JLU 2020-2023 Jeep Gladiator JT Why Replace Your Washer Cap? A missing or broken washer fluid cap seems minor — until you're on the highway with a salt-covered windshield or on a dusty trail with zero visibility. An unsealed reservoir allows washer fluid to evaporate, dirt to contaminate the system, and can cause the washer pump to lose prime. This affordable replacement prevents those problems and takes 5 seconds to install. Frequently Asked Questions Q: Will this fit my 2015 JK Unlimited?A: Yes, this cap fits all 2007-2018 Wrangler JK and JKU models. The washer fluid reservoir cap design was unchanged throughout the entire JK production run. Q: Is this an exact OEM match?A: Yes, this cap matches the OEM Mopar part (55077249AB) in dimensions, material, and fit. It snaps securely and seals properly — indistinguishable from the original. Q: Does it fit the rear window washer reservoir?A: No, this is for the front windshield washer reservoir only. The JK rear washer reservoir (if equipped) uses a different cap design located in the rear cargo area. Q: Will this cap crack in cold weather?A: The polypropylene material is rated for temperatures from -40°F to 240°F, making it suitable for extreme cold climates without becoming brittle. It also withstands the engine bay heat of desert off-road driving. 📚 Related Guides & Articles Jeep Wrangler JK vs JL Parts Compatibility Guide Top 10 Jeep Wrangler Mods Under $50 Jeep Wrangler JK Common Problems & Fixes

Read more less

Product Overview The iFJF LR009705 Fuel Filter is a precision-engineered replacement for Land Rover LR3 and LR4 models equipped with the 2.7L TDV6 diesel engine. This high-efficiency filter removes water and microscopic contaminants from diesel fuel before it reaches your high-pressure common rail injection system — protecting injectors from catastrophic damage that can cost thousands to repair. Manufactured to IATF 16949 standards for reliable OEM-equivalent performance. Key Features OEM-Spec Filtration Efficiency: High-performance media captures particles as small as 3-5 microns — essential for protecting sensitive common rail injectors operating at 1,600+ bar. Integrated Water Separation: Specialized media removes emulsified water from diesel fuel, preventing injector corrosion and microbial growth in the fuel system. Direct Fit — No Modifications: Precision-engineered to match the factory LR3/LR4 filter housing exactly — no adapters, no modifications, no leaks. Replaces WJI500020 & LR009705: Cross-references to OEM Land Rover part numbers for guaranteed compatibility and performance. 2007-2009 Model Coverage: Fits Discovery 3 (LR3) and Discovery 4 (LR4) with the 2.7L TDV6 diesel engine. Vehicle Compatibility Make Model Years Engine Land Rover LR3 (Discovery 3) 2007-2009 2.7L TDV6 Diesel Land Rover LR4 (Discovery 4) 2007-2009 2.7L TDV6 Diesel OE Cross-Reference Brand Part Number Land Rover / Jaguar LR009705 Land Rover / Jaguar WJI500020 Why Quality Filtration Matters for TDV6 Engines The 2.7L TDV6 common rail diesel uses piezo-electric injectors operating at extremely high pressures (up to 1,600 bar). Any contamination — even microscopic particles or water droplets — can cause injector tip erosion, internal corrosion, and eventual failure. A single injector replacement can cost $800+. The LR009705 filter is your most important line of defense against fuel system damage. Frequently Asked Questions Q: Will this fit my 2008 LR3 HSE diesel?A: Yes. This filter fits all 2007-2009 Land Rover LR3 and LR4 models equipped with the 2.7L TDV6 diesel engine. Q: How often should the fuel filter be replaced?A: Land Rover recommends replacement every 30,000 miles or every other service interval. Replace annually if fuel quality is a concern. Q: Is this the same as OEM WJI500020?A: Yes. This filter replaces Land Rover part numbers LR009705 and WJI500020. Manufactured to meet or exceed OEM specifications. Q: Can I replace this myself?A: The fuel filter on the LR3/LR4 is accessible and DIY-friendly with basic tools. Always prime the fuel system after replacement by cycling the ignition 3-4 times before starting. Q: Will this filter water in diesel?A: Yes. The filter media is designed to separate both particulate contamination and emulsified water for complete fuel system protection. Related Products PU 936/1 X Fuel Filter for VW Audi 1.9/2.0 TDI

Read more less

Product Overview The WK 820/18 Fuel Filter is a premium-grade replacement fuel filter engineered to deliver OEM-level performance at an aftermarket price. Designed for Mercedes applications (2010-2020), this component ensures your engine receives proper filtration for optimal performance and longevity. Cross-References: 2009-2015, 2009-2020, 2010-2014, 2010-2015, 820/18, GLK200 Key Features & Benefits Superior Filtration: Advanced multi-layer media captures 99.9% of contaminants down to the rated micron level Maximum Fuel Flow: Engineered pleat design ensures unrestricted fuel delivery even under heavy load Corrosion-Resistant: Heavy-duty construction withstands diesel fuel additives and moisture Easy Installation: Direct fit replacement — no modifications needed for listed applications Quality Assured: Each unit undergoes rigorous quality control testing before shipment Vehicle Compatibility 📋 Cross-Reference Compatibility OEM Part Numbers 2009-2015, 2009-2020, 2010-2014, 2010-2015, 820/18, GLK200 Fitment Years 2010-2020 Vehicle Applications Mercedes Why Choose iFJF? At iFJF Direct, we specialize in providing diesel and heavy-duty vehicle owners with high-quality replacement parts at competitive prices. Our fuel filters are sourced from trusted manufacturers and backed by our commitment to quality and customer service. ✅ OEM-Spec Quality Without the OEM Price ✅ Fast Shipping from US Warehouses ✅ Dedicated Customer Support Team ✅ 30-Day Easy Returns Technical Specifications 📐 Technical Specifications Micron Rating 5-30 Micron (Application-Specific) Media Type High-Efficiency Cellulose/Synthetic Blend Water Separation ≥95% Efficiency (Where Applicable) Replacement Interval Per Vehicle Manufacturer Recommendations Package Includes 1x Fuel Filter (as shown in listing images) Frequently Asked QuestionsQ: How often should I replace this filter?A: For diesel engines, we recommend replacing it every 15,000-30,000 miles or every other oil change. Heavy-duty applications may require more frequent changes.Q: Will this fit my vehicle?A: Check the OEM part number cross-reference in the compatibility section. If your existing filter matches one of the listed part numbers, this filter fits.Q: What micron rating does this filter use?A: Manufactured to OEM specifications, typically 5-10 microns for diesel fuel systems.Q: Do you offer a warranty?A: Yes! All iFJF products come with our satisfaction guarantee. Contact us if you experience any issues. Q: How fast do you ship?A: Orders ship within 1-2 business days from our US warehouses. Typical delivery is 3-7 business days depending on your location.

Read more less

WK 853/3 X Fuel Filter — Precision Filtration for VW TDI Engines The iFJF WK 853/3 X Diesel Fuel Filter is a direct OEM-spec replacement for VW's 1.9L and 2.0L TDI engines found in the Beetle, Golf, Jetta, and Passat from 1999-2006. The integrated check valve prevents fuel from draining back to the tank, ensuring reliable cold starts every time. Key Features OEM Cross Reference: Direct replacement for 1C0127401, WK 853/3 X, and equivalent Mann/Mahle filters. Integrated Check Valve: Maintains fuel prime in the lines overnight — no more extended cranking on cold mornings. 4-Bar Pressure Rating: Designed for the PD (Pumpe Düse) unit injector fuel system used in VW TDI engines. Inline Design: Mounts in the factory fuel line bracket under the vehicle — straightforward replacement. 10 Micron Filtration: Protects expensive PD unit injectors from fuel contamination and wear. Vehicle Compatibility Make Model Year Range Engine VW Beetle TDI 1999-2006 1.9L ALH/BEW TDI VW Golf TDI 2000-2006 1.9L ALH/BEW TDI VW Jetta TDI 2000-2005 1.9L ALH/BEW TDI VW Passat TDI 2004-2005 2.0L BHW TDI Why the WK 853/3 X Check Valve Matters Unlike spin-on filters, inline fuel filters are part of the pressurized fuel circuit. The integrated check valve in the WK 853/3 X maintains system pressure when the engine is off. Without it, fuel drains back to the tank overnight, leading to extended cranking times and excessive starter wear. Always use a filter with a functioning check valve for these TDI engines. Frequently Asked Questions Q: Will this fit my 2003 Jetta TDI?A: Yes! The WK 853/3 X is the correct fuel filter for all 1999.5-2005 Jetta TDI models with the 1.9L ALH or BEW engine. Q: How often should the fuel filter be changed?A: VW recommends every 20,000 miles. We recommend every 15,000 miles if you use biodiesel blends above B5. Q: Does this filter have the thermostatic T-fitting?A: This filter body has the ports for the T-fitting. You'll reuse your existing thermostatic T-fitting (the plastic piece with fuel lines on top of the filter). Q: Will a bad check valve cause hard starting?A: Absolutely. If your TDI cranks for 5+ seconds before starting, especially after sitting overnight, a failed check valve in the fuel filter is the most common cause.

Read more less

Product Overview WS21X10003 Water Softener Rotor Position Switch - GE Compatible 7305150. Engineered for reliable performance and precision fitment, this iFJF aftermarket part meets or exceeds OEM specifications for durability and function. Ideal for DIY mechanics and professional technicians alike. Key Features Exact OEM Replacement: Direct fit for GE / SmartWater water softener models using WS21X10003. Reliable Switching: Precision micro-switch ensures accurate rotor position detection for proper regeneration cycles. Easy Installation: Plug-and-play replacement — no soldering or special tools required. Durable Construction: Built to withstand years of operation in humid water softener environments. Compatibility Year Make Model Engine/Notes See Description WS21X10003 Water Softener Rotor Position Switch - Direct Fit ⚠️ Always verify fitment with your specific vehicle year, make, model, and engine before ordering. Contact our support team for compatibility questions. Specifications Specification Value Brand iFJF Product Type Water Softener Parts SKU FJ-JP-X-SS10-CK Price $29.99 USD Why Choose iFJF? Quality Assurance: Every iFJF part undergoes rigorous quality inspection before shipping. Precision Engineering: Manufactured to tight tolerances for guaranteed fitment. Expert Support: Our team of diesel and automotive specialists is ready to help with any questions. Fast Shipping: Orders ship within 1-2 business days from our US warehouses. Frequently Asked Questions Q: Will this fit my water softener model?A: This rotor position switch is designed for GE / SmartWater water softeners. Check the compatibility list for your specific model. It replaces OEM part number WS21X10003. Q: What are signs of a bad rotor position switch?A: The water softener fails to regenerate, gets stuck mid-cycle, displays error codes, or the motor continues running without advancing the cycle. This switch tells the control board the rotor position. Q: Is professional installation required?A: While a handy homeowner can replace this part, we recommend professional installation if you're not comfortable working with water softener internals. Power off the unit and relieve water pressure before starting. Order your WS21X10003 Water Softener Rotor Position Switch - today — fast shipping, expert support, and the quality you can trust from iFJF Direct. 📖 Related Guides & Articles 🔗 Above Ground Pool Plumbing Parts Explained 🔗 DIY ABS Diesel Fuel Tank for Camper Vans 🔍 Explore More Parts Looking for compatible parts? Browse our full selection of Water Softener & Home Parts for your vehicle or equipment. iFJF Direct offers quality aftermarket parts with fast shipping.

Read more less

X77094 Pool Vacuum Hose Connector — Twist-Lock Replacement for Zodiac Cleaners The iFJF X77094 Pool Vacuum Hose Connector is a precision-engineered replacement for the twist-lock hose adapter used on Zodiac MX6, MX8, X7 Quattro, and compatible pool cleaners. When your original connector cracks, wears out, or no longer locks securely, this durable replacement gets your cleaner back to work. Key Features Exact Replacement for X77094: Direct fit for Zodiac Baracuda MX6, MX8, MX8 Elite, X7 Quattro pool cleaners. Twist-Lock Design: Secure, leak-free connection that won't accidentally disconnect during cleaning cycles. Durable ABS Construction: UV-resistant and chemical-resistant — won't crack or degrade from chlorine, salt, or sun exposure. Universal Hose Compatibility: Works with standard 1.5" pool vacuum hose sections and leaf catcher canisters. Tool-Free Install: Simply twist to lock onto your existing hose — no tools, clamps, or adhesives needed. Compatible Pool Cleaners Brand Model Part Number Zodiac MX6 X77094 Zodiac MX8 / MX8 Elite X77094 Zodiac X7 Quattro X77094 Universal Leaf Catcher Hose 1.5" Twist-Lock When to Replace Your Hose Connector Loose Connection: Hose keeps disconnecting from the cleaner or leaf catcher during operation. Visible Cracks: Hairline cracks in the plastic body — these will only get worse. Air Leaks: Cleaner loses suction due to air entering through a worn connector seal. Stripped Threads: Twist-lock tabs are worn down and no longer hold securely. Frequently Asked Questions Q: Will this fit my Zodiac MX8 Elite?A: Yes! This connector is compatible with all Zodiac MX6, MX8, MX8 Elite, and X7 Quattro models that use the twist-lock hose system. Q: Can I use this with a non-Zodiac pool cleaner?A: If your cleaner uses a standard 1.5" twist-lock hose connection, this connector should work. It's also compatible with universal leaf catcher canisters. Q: Do I need any special tools?A: No tools required. Simply align the tabs, push in, and twist to lock. The entire replacement takes less than 30 seconds. Q: Is this the same as the OEM X77094 part?A: Yes. This is manufactured to the same specifications as the OEM Zodiac X77094 connector, at a significantly lower price point.

Read more less