94W83 Lennox Furnace Control Board Replaces 103085-02 103085-03

Description

94W83 Furnace Control Board for Lennox Gas Furnaces — Replaces 103085-01, 103085-02, 103085-03, 81W11 & 1012-977A

The iFJF 94W83 is a single-stage furnace ignition control board for Lennox, Armstrong and Ducane gas furnaces. It is the board sold under Lennox catalog number 94W83, replaces Lennox part numbers 103085-01, 103085-02, 103085-03 and 81W11, and cross-references the Honeywell / UTEC number 1012-977A (1012-977A-I). It runs on an 18–30 VAC, 50/60 Hz control circuit, reuses the factory connector and mounting pins, and requires no programming.

The board sequences the whole light-off: it starts the inducer, powers the igniter, opens the gas valve at the right moment, proves flame through the sensor, and holds the blower off until the heat exchanger warms up. When it fails, the furnace usually tells you in one of three ways — the inducer runs and nothing else happens, the igniter glows but the gas valve never opens, or the burners light and drop out seconds later until the board locks out. Match the number printed on the board you are removing against the cross-reference table below before ordering: Lennox reused the same cabinet with more than one control.

Key Features

  • Five Lennox Numbers, One Board: Covers 94W83, 103085-01, 103085-02, 103085-03 and 81W11, so a single spare clears the superseded revisions of the same control.
  • Single-Stage Ignition Sequence: Drives inducer, igniter and gas valve in the correct order and proves flame by rectification before it lets the blower start.
  • 18–30 VAC Control Circuit: Runs on the standard Class II low-voltage supply already in the furnace — no transformer, adapter or field wiring change.
  • Fan Delay Built In: Holds the blower until the plenum is warm on a call for heat, then keeps it running to sweep the residual heat after the burner shuts down.
  • Factory-Matched Terminals: Spade terminals and the multi-pin connector mirror the original layout, so every lead seats back where it came off — no splicing, no drilling, no jumper wires.
  • No Programming: Nothing to flash or configure. Photograph the wiring, transfer the leads, and the board takes over on the next heating call.
  • Snap-In Mounting Pins: Sits on the same standoffs as the board it replaces, using the existing screw or pin pattern.
  • Bench-Checked Before Shipping: Every board is inspected before it leaves the warehouse. Backed by iFJF Quality Guarantee · Easy Returns · Wiring Support.

Compatibility / Fitment

The 94W83 board is fitted from the factory to the Lennox furnace series below, and to Armstrong and Ducane furnaces built on the same Lennox control platform. Model prefixes are a starting point — the part number printed on the board you are removing is the reliable check.
Furnace Series Brand Notes
80AF1DF Lennox 80% AFUE single-stage gas furnace, downflow / horizontal configurations
80AF1UH Lennox 80% AFUE single-stage gas furnace, upflow / horizontal configurations
92AF1DF Lennox Same board position on the 92 series platform
95AF1UH Lennox Same board position on the 95 series platform
Armstrong / Ducane Armstrong, Ducane Units built on the same Lennox control platform with a 1012-977A board

Wiring and terminal positions change between furnace generations, and Lennox shipped more than one control in the same cabinet over the years. If the connector on the new board does not match the harness in your unit, stop and send us a photo of the existing board with the part number visible — we will confirm the application before you install.

Specifications

Specification Value
Part Number 94W83
Cross-Reference 103085-01, 103085-02, 103085-03, 81W11, 1012-977A, 1012-977A-I
Component Type Furnace ignition control board (single-stage)
Control Voltage 18–30 VAC, 50/60 Hz
Functions Ignition timing, inducer control, gas valve, flame rectification, blower delay
Terminals Factory-matched spade terminals and multi-pin connector
Mounting Snap-in mounting pins / existing standoffs
Board Size Approx. 5.8" × 5" × 0.9" (147 × 127 × 23 mm)
Package Weight 3.7 oz (104 g)
Includes 1 × 94W83 furnace control board
Quality iFJF Quality Guarantee

Installation Tips

  1. Two supplies, not one. Switch off the furnace service switch and the breaker feeding the unit, then close the manual gas valve. The 24 VAC control circuit comes from the transformer inside the same cabinet, so the service switch alone is not enough.
  2. Photograph before you touch anything. One clear phone photo of the board with every lead in place beats any wiring diagram, especially the thermostat, gas valve and inducer leads.
  3. Mark the flame sensor lead. The flame sensor and the igniter both land on the board with single wires and are easy to swap. Label them as you pull them off.
  4. Handle by the edges. Static damages more boards than heat does. Touch the cabinet before picking the board up and keep your fingers off the pins and relay tops.
  5. Transfer the leads one at a time. Move each lead from the old board to the matching terminal on the new one before starting the next, instead of pulling them all off first.
  6. Watch the sequence on first start. Restore power and call for heat: inducer starts → igniter glows → gas valve opens → burners light → blower starts after the delay. If the burner lights and then drops out after a few seconds, clean or replace the flame sensor before assuming the board is at fault again.

Frequently Asked Questions

Q: What part numbers does the 94W83 furnace control board replace?

A: 94W83 is the Lennox catalog number for this board. It replaces Lennox 103085-01, 103085-02, 103085-03 and 81W11, and cross-references the Honeywell / UTEC number 1012-977A, printed on the box as 1012-977A-I. Distributor catalogs sometimes print these numbers with a revision suffix. Compare the number on the board you are removing with the cross-reference table on this page before ordering.

Q: Which Lennox furnaces use the 94W83 control board?

A: It is fitted from the factory to Lennox 80AF1DF, 80AF1UH, 92AF1DF and 95AF1UH series gas furnaces, and to Armstrong and Ducane furnaces built on the same Lennox control platform. Because manufacturers reuse one board across several model revisions, the part number printed on the old board is the reliable check, not the furnace model name alone.

Q: Is the 94W83 a single-stage or two-stage control?

A: It is a single-stage ignition control: one ignition sequence, one gas valve output and one blower delay per call for heat, rated for an 18-30 VAC, 50/60 Hz control circuit. If your furnace is a two-stage or modulating model, send us the model and serial number from the rating plate before ordering so we can confirm the correct board.

Q: My furnace inducer runs but the burners never light. Is the board bad?

A: A running inducer with no ignition points at the board or at the components it drives. Check in this order: the pressure switch tubing is clear and the switch closes, the igniter is not cracked and reads continuity, and the flame sensor is clean. If the igniter glows and the gas valve never opens, or the burners light and drop out within seconds until the board locks out, the control board is the usual cause. A board that will not start the inducer at all is a different fault - verify 24 VAC at the board terminals first.

Q: Do I need to rewire anything or program the new board?

A: No. The 94W83 is a plug-in replacement that reuses the existing terminal block, factory connector and mounting pins. There is nothing to flash, no harness to build and no splicing. Photograph the old wiring, move the leads across one at a time, and restore power.

Q: Is this a genuine Lennox board or an aftermarket replacement?

A: It is an iFJF aftermarket replacement built to the same fitment and function as the factory board. Lennox, Armstrong, Ducane and Honeywell part numbers are referenced for identification only and remain the property of their owners. It is covered by the iFJF Quality Guarantee, with Easy Returns and Wiring Support if the wiring does not line up.

📊 iFJF 94W83 vs the Dealership Board

Same board position, same single-stage sequence. The difference is what one spare covers — and whether you have to order it through an HVAC wholesaler with a contractor account.

Feature Dealership / OEM Counter iFJF 94W83
Numbers covered Sold as one current number; older revisions are superseded to it One board replaces 94W83, 103085-01, 103085-02, 103085-03 and 81W11
Control type Single-stage ignition control Single-stage ignition control
Control voltage 18–30 VAC, 50/60 Hz 18–30 VAC, 50/60 Hz
Terminal layout Factory layout Factory-matched layout, no rewiring
Programming required None None
Cross-reference support Counter staff look up the supersession Cross-reference table on this page, plus photo confirmation by email
Buying channel HVAC wholesale, contractor account often required Order direct, in stock and ready to ship

📦 Related Products & Guides

Working through a no-heat call? These are the furnace control boards our customers compare with the 94W83 most often.

Product Fits Price
50A55-843 Furnace Control Board Lennox & White-Rodgers gas furnaces $137.99
1012-925C Furnace Control Board Rheem, Ruud & Weather King HSI furnaces $179.99
031-01267-001A Furnace Control Board York, Luxaire & Coleman 120 V HSI furnaces $89.99
920915 Furnace Control Board Nordyne G7 / M7 furnaces — replaces 624742 $79.99

Browse the full range of HVAC control boards and electronics, or see every home & garden heating part we stock.

🔄 94W83 Cross Reference & Replacement Guide

Part Number Notes
94W83 Lennox catalog number — iFJF equivalent board
103085-01 Lennox control part number
103085-02 Lennox control part number
103085-03 Lennox control part number
81W11 Earlier Lennox / Honeywell number for the same board
1012-977A Honeywell / UTEC number
1012-977A-I UTEC number as printed on the box

Distributor catalogs also list the same board with a revision suffix (for example 81W1101 or 94W8301) — match the base number. OEM numbers are listed for identification only. The 94W83 is an ignition control board, not a blower or gas valve control: match the function and the part number of the board you are replacing, not just the furnace model.

Need a hand identifying your board? Send us a photo of the existing board with the part number visible and the model and serial numbers from the furnace rating plate, and our team will confirm the match before you order.
Email: support@ifjf.com
Backed by ISO 9001:2015 and IATF 16949:2016 quality management system certifications.

94W83 Lennox Furnace Control Board Replaces 103085-02 103085-03

Product form

SKU: FJ-CB-94W83

$93.99

      Description

      94W83 Furnace Control Board for Lennox Gas Furnaces — Replaces 103085-01, 103085-02, 103085-03, 81W11 & 1012-977A

      The iFJF 94W83 is a single-stage furnace ignition control board for Lennox, Armstrong and Ducane gas furnaces. It is the board sold under Lennox catalog number 94W83, replaces Lennox part numbers 103085-01, 103085-02, 103085-03 and 81W11, and cross-references the Honeywell / UTEC number 1012-977A (1012-977A-I). It runs on an 18–30 VAC, 50/60 Hz control circuit, reuses the factory connector and mounting pins, and requires no programming.

      The board sequences the whole light-off: it starts the inducer, powers the igniter, opens the gas valve at the right moment, proves flame through the sensor, and holds the blower off until the heat exchanger warms up. When it fails, the furnace usually tells you in one of three ways — the inducer runs and nothing else happens, the igniter glows but the gas valve never opens, or the burners light and drop out seconds later until the board locks out. Match the number printed on the board you are removing against the cross-reference table below before ordering: Lennox reused the same cabinet with more than one control.

      Key Features

      • Five Lennox Numbers, One Board: Covers 94W83, 103085-01, 103085-02, 103085-03 and 81W11, so a single spare clears the superseded revisions of the same control.
      • Single-Stage Ignition Sequence: Drives inducer, igniter and gas valve in the correct order and proves flame by rectification before it lets the blower start.
      • 18–30 VAC Control Circuit: Runs on the standard Class II low-voltage supply already in the furnace — no transformer, adapter or field wiring change.
      • Fan Delay Built In: Holds the blower until the plenum is warm on a call for heat, then keeps it running to sweep the residual heat after the burner shuts down.
      • Factory-Matched Terminals: Spade terminals and the multi-pin connector mirror the original layout, so every lead seats back where it came off — no splicing, no drilling, no jumper wires.
      • No Programming: Nothing to flash or configure. Photograph the wiring, transfer the leads, and the board takes over on the next heating call.
      • Snap-In Mounting Pins: Sits on the same standoffs as the board it replaces, using the existing screw or pin pattern.
      • Bench-Checked Before Shipping: Every board is inspected before it leaves the warehouse. Backed by iFJF Quality Guarantee · Easy Returns · Wiring Support.

      Compatibility / Fitment

      The 94W83 board is fitted from the factory to the Lennox furnace series below, and to Armstrong and Ducane furnaces built on the same Lennox control platform. Model prefixes are a starting point — the part number printed on the board you are removing is the reliable check.
      Furnace Series Brand Notes
      80AF1DF Lennox 80% AFUE single-stage gas furnace, downflow / horizontal configurations
      80AF1UH Lennox 80% AFUE single-stage gas furnace, upflow / horizontal configurations
      92AF1DF Lennox Same board position on the 92 series platform
      95AF1UH Lennox Same board position on the 95 series platform
      Armstrong / Ducane Armstrong, Ducane Units built on the same Lennox control platform with a 1012-977A board

      Wiring and terminal positions change between furnace generations, and Lennox shipped more than one control in the same cabinet over the years. If the connector on the new board does not match the harness in your unit, stop and send us a photo of the existing board with the part number visible — we will confirm the application before you install.

      Specifications

      Specification Value
      Part Number 94W83
      Cross-Reference 103085-01, 103085-02, 103085-03, 81W11, 1012-977A, 1012-977A-I
      Component Type Furnace ignition control board (single-stage)
      Control Voltage 18–30 VAC, 50/60 Hz
      Functions Ignition timing, inducer control, gas valve, flame rectification, blower delay
      Terminals Factory-matched spade terminals and multi-pin connector
      Mounting Snap-in mounting pins / existing standoffs
      Board Size Approx. 5.8" × 5" × 0.9" (147 × 127 × 23 mm)
      Package Weight 3.7 oz (104 g)
      Includes 1 × 94W83 furnace control board
      Quality iFJF Quality Guarantee

      Installation Tips

      1. Two supplies, not one. Switch off the furnace service switch and the breaker feeding the unit, then close the manual gas valve. The 24 VAC control circuit comes from the transformer inside the same cabinet, so the service switch alone is not enough.
      2. Photograph before you touch anything. One clear phone photo of the board with every lead in place beats any wiring diagram, especially the thermostat, gas valve and inducer leads.
      3. Mark the flame sensor lead. The flame sensor and the igniter both land on the board with single wires and are easy to swap. Label them as you pull them off.
      4. Handle by the edges. Static damages more boards than heat does. Touch the cabinet before picking the board up and keep your fingers off the pins and relay tops.
      5. Transfer the leads one at a time. Move each lead from the old board to the matching terminal on the new one before starting the next, instead of pulling them all off first.
      6. Watch the sequence on first start. Restore power and call for heat: inducer starts → igniter glows → gas valve opens → burners light → blower starts after the delay. If the burner lights and then drops out after a few seconds, clean or replace the flame sensor before assuming the board is at fault again.

      Frequently Asked Questions

      Q: What part numbers does the 94W83 furnace control board replace?

      A: 94W83 is the Lennox catalog number for this board. It replaces Lennox 103085-01, 103085-02, 103085-03 and 81W11, and cross-references the Honeywell / UTEC number 1012-977A, printed on the box as 1012-977A-I. Distributor catalogs sometimes print these numbers with a revision suffix. Compare the number on the board you are removing with the cross-reference table on this page before ordering.

      Q: Which Lennox furnaces use the 94W83 control board?

      A: It is fitted from the factory to Lennox 80AF1DF, 80AF1UH, 92AF1DF and 95AF1UH series gas furnaces, and to Armstrong and Ducane furnaces built on the same Lennox control platform. Because manufacturers reuse one board across several model revisions, the part number printed on the old board is the reliable check, not the furnace model name alone.

      Q: Is the 94W83 a single-stage or two-stage control?

      A: It is a single-stage ignition control: one ignition sequence, one gas valve output and one blower delay per call for heat, rated for an 18-30 VAC, 50/60 Hz control circuit. If your furnace is a two-stage or modulating model, send us the model and serial number from the rating plate before ordering so we can confirm the correct board.

      Q: My furnace inducer runs but the burners never light. Is the board bad?

      A: A running inducer with no ignition points at the board or at the components it drives. Check in this order: the pressure switch tubing is clear and the switch closes, the igniter is not cracked and reads continuity, and the flame sensor is clean. If the igniter glows and the gas valve never opens, or the burners light and drop out within seconds until the board locks out, the control board is the usual cause. A board that will not start the inducer at all is a different fault - verify 24 VAC at the board terminals first.

      Q: Do I need to rewire anything or program the new board?

      A: No. The 94W83 is a plug-in replacement that reuses the existing terminal block, factory connector and mounting pins. There is nothing to flash, no harness to build and no splicing. Photograph the old wiring, move the leads across one at a time, and restore power.

      Q: Is this a genuine Lennox board or an aftermarket replacement?

      A: It is an iFJF aftermarket replacement built to the same fitment and function as the factory board. Lennox, Armstrong, Ducane and Honeywell part numbers are referenced for identification only and remain the property of their owners. It is covered by the iFJF Quality Guarantee, with Easy Returns and Wiring Support if the wiring does not line up.

      📊 iFJF 94W83 vs the Dealership Board

      Same board position, same single-stage sequence. The difference is what one spare covers — and whether you have to order it through an HVAC wholesaler with a contractor account.

      Feature Dealership / OEM Counter iFJF 94W83
      Numbers covered Sold as one current number; older revisions are superseded to it One board replaces 94W83, 103085-01, 103085-02, 103085-03 and 81W11
      Control type Single-stage ignition control Single-stage ignition control
      Control voltage 18–30 VAC, 50/60 Hz 18–30 VAC, 50/60 Hz
      Terminal layout Factory layout Factory-matched layout, no rewiring
      Programming required None None
      Cross-reference support Counter staff look up the supersession Cross-reference table on this page, plus photo confirmation by email
      Buying channel HVAC wholesale, contractor account often required Order direct, in stock and ready to ship

      📦 Related Products & Guides

      Working through a no-heat call? These are the furnace control boards our customers compare with the 94W83 most often.

      Product Fits Price
      50A55-843 Furnace Control Board Lennox & White-Rodgers gas furnaces $137.99
      1012-925C Furnace Control Board Rheem, Ruud & Weather King HSI furnaces $179.99
      031-01267-001A Furnace Control Board York, Luxaire & Coleman 120 V HSI furnaces $89.99
      920915 Furnace Control Board Nordyne G7 / M7 furnaces — replaces 624742 $79.99

      Browse the full range of HVAC control boards and electronics, or see every home & garden heating part we stock.

      🔄 94W83 Cross Reference & Replacement Guide

      Part Number Notes
      94W83 Lennox catalog number — iFJF equivalent board
      103085-01 Lennox control part number
      103085-02 Lennox control part number
      103085-03 Lennox control part number
      81W11 Earlier Lennox / Honeywell number for the same board
      1012-977A Honeywell / UTEC number
      1012-977A-I UTEC number as printed on the box

      Distributor catalogs also list the same board with a revision suffix (for example 81W1101 or 94W8301) — match the base number. OEM numbers are listed for identification only. The 94W83 is an ignition control board, not a blower or gas valve control: match the function and the part number of the board you are replacing, not just the furnace model.

      Need a hand identifying your board? Send us a photo of the existing board with the part number visible and the model and serial numbers from the furnace rating plate, and our team will confirm the match before you order.
      Email: support@ifjf.com
      Backed by ISO 9001:2015 and IATF 16949:2016 quality management system certifications.

      Recently viewed products

      © 2026 iFJF Direct | Sitemap

        • American Express
        • Diners Club
        • Discover
        • Maestro
        • Mastercard
        • PayPal
        • Visa

        Login

        Forgot your password?

        Don't have an account yet?
        Create account