Description
iFJF 2-Piece Door Bushing Removal Tool & Hinge Liner Set for Jeep Wrangler JK/JL/Gladiator JT 2007-2021
The iFJF 2-Piece Door Bushing Removal Tool Set is the complete solution for servicing both sides of your Jeep Wrangler or Gladiator. Instead of buying a single tool and working one door at a time, this kit includes two professional-grade stainless steel removal tools — one for the driver side, one for the passenger side — plus replacement hinge liner pins. Service both doors in a single session and restore factory-smooth operation to every hinge on your Jeep.
Key Features
-
2-Piece Set — Both Doors Covered: Includes two stainless steel removal tools plus hinge liner pins. Service upper and lower hinges on both driver and passenger doors in one complete session. No need to buy additional tools or pins separately.
-
Heavy-Duty Stainless Steel Construction: Both removal tools are machined from high-grade stainless steel that withstands repeated hammer impacts without deforming. Built for years of use — service your own Jeep today and help a friend with theirs tomorrow.
-
Fixes All Common Door Problems: Addresses squeaky hinges, rattling door panels, loose-fitting doors, and difficult-to-close doors. All symptoms of worn, corroded, or swollen OE door hinge bushings.
-
Simple Hammer Installation: Align the tool at the top of the hinge, tap firmly with a standard hammer, and drive out the old bushing. Install the new liner pin with a rubber mallet. No press, no special tools, no mechanic experience needed.
-
Broad Vehicle Compatibility: Works across the entire modern Wrangler platform — JK, JKU, JL, JLU, and Gladiator JT from 2007 through 2021.
-
2-Year iFJF Warranty: Quality guaranteed. If anything goes wrong, we'll make it right.
Vehicle Fitment
-
Jeep Wrangler JK (2007-2018): 2-door, all trims
-
Jeep Wrangler JKU (2007-2018): 4-door, all trims
-
Jeep Wrangler JL (2018-2021): 2-door, all trims
-
Jeep Wrangler JLU (2018-2021): 4-door, all trims
-
Jeep Gladiator JT (2020-2021): All trims
-
NOT compatible: TJ (1997-2006), YJ (1987-1995), or any pre-JK models
Installation Guide
-
Support Both Doors: Open each door and place support underneath. Remove the hinge pins from both doors — keep track of which pin goes where.
-
Remove Old Bushings: For each hinge (4 total: upper/lower × left/right), place the iFJF removal tool at the top of the hinge and tap with a hammer until the OE bushing is fully driven out.
-
Clean Hinge Bores: Remove all rust, debris, and corrosion from each hinge bore. A wire brush and brake cleaner work well. Apply a light coat of grease or anti-seize lubricant.
-
Install New Hinge Liner Pins: Tap the fresh plastic hinge liner pins into place using a rubber mallet. Ensure they seat fully and evenly in each bore.
-
Reinstall Doors: Rehang both doors and reinsert the hinge pins. Test each door for smooth operation — they should open and close effortlessly with no squeaks or rattles.
Pro Tip: Mark each door's hinge pin position before removal (e.g., "DS-Upper") to ensure correct reinstallation. Protect your paint with a shop towel or cardboard under the hinge during hammering.
Why Two Tools Beat One
If you're servicing worn door bushings, the odds are high that both sides need attention. Door bushings wear at roughly the same rate, and corrosion doesn't pick favorites. Having two removal tools in one kit means you can complete the entire job — all four hinges — without sharing a single tool between sides. It also means you have a backup tool for future service or for helping a fellow Jeep owner in your off-road group. The value of a complete 2-tool kit versus buying two separate single-tool kits is significant, and you get everything you need in one box.
Package Includes
- 2 × Stainless Steel Door Bushing Removal Tools
- Complete Set of Hinge Liner Pins (for both doors)
- Installation Guide
Frequently Asked Questions
Does this kit include alignment pins?
No. This kit includes 2 removal tools and replacement hinge liner pins. If you need alignment pins for precise door reinstallation, those are available separately in our complete hinge service kit (FJ-JP-DR-GE-ZH4).
Will this work on the 4-door JKU and JLU?
Yes. The removal tools work identically on 2-door and 4-door configurations for both the JK and JL platforms. The hinge design is consistent across all body styles.
Can I use this on a 2022-2023 model?
The listing specifies 2007-2021 compatibility. While the hinge design has remained consistent, we recommend contacting our support team to verify fitment for 2022+ model years before purchasing.
How long does a full 2-door service take?
Most owners complete the full service (all 4 hinges, both doors) in 45-60 minutes. Heavily corroded bushings may require more hammer time, but the stainless steel tool is built to handle it.
📖 Related Installation Guides & Articles
