All Carburetors

Autolite 1100 / 1101 1-Barrel Carburetor — Complete Unit, Pre-Tuned & Ready to Run This is a fully assembled, pre-tuned Autolite 1100 carburetor — not a rebuild kit or individual parts. The iFJF Autolite 1100 delivers factory-spec performance for Ford's legendary 200 cubic inch (3.3L) inline-six engine found in 1963–1967 Mustangs, Falcons, Fairlanes, Comets, and Econoline vans. Each unit is pre-adjusted at the factory for the correct air-fuel mixture and idle speed, so you can unbolt your old carb, bolt this one on, and drive the same day. No tuning, no guesswork, no frustration. Key Features & Benefits Complete, Pre-Tuned Carburetor Forget sourcing gaskets, chasing rebuild parts, or spending hours trying to tune a worn-out core. This is a complete replacement carburetor — factory-adjusted for the 200ci inline-6. The throttle plate, choke mechanism, float, and all internal passages are brand new and calibrated to Ford's original specifications. Manual Choke — Period Correct Features the correct manual choke setup as used on 1963-1967 Ford 200ci six-cylinder engines. The choke cable attachment point matches the factory configuration, preserving the original driving experience and under-hood appearance. Direct Bolt-On Fitment The mounting flange, throttle linkage, fuel line connection, and vacuum port are in the exact same positions as the original Autolite 1100/1101. No adapter plates, no modified linkages, no custom fuel lines. Unbolt the old, bolt on the new, connect three things, and start. Technical Specifications Specification Detail Model iFJF Autolite 1100/1101 Carburetor Type 1-Barrel Downdraft Choke Type Manual Engine Ford 200ci (3.3L) Inline-6 Year Range 1963-1967 Venturi Size 1.20" (30.5mm) Mount Type 3-Bolt Flange Compatible Ford Models 1964½–1967 Ford Mustang 200ci 3.3L I6 1963–1967 Ford Falcon 200ci I6 1963–1967 Ford Fairlane 200ci I6 1963–1967 Mercury Comet 200ci I6 1963–1967 Ford Econoline Van 200ci I6 1965–1967 Ford Ranchero 200ci I6 Installation Disconnect the battery. Remove the air cleaner. Disconnect the fuel line at the carburetor inlet. Disconnect the manual choke cable, throttle linkage, and the vacuum advance line. Remove the three mounting nuts (1/2" wrench). Lift off the old carburetor and mounting gasket. Clean the intake manifold mounting surface thoroughly. Place the new gasket on the manifold studs. Position the new carburetor and tighten the mounting nuts evenly (12-15 ft-lbs). Reconnect the fuel line (use a flare nut wrench to avoid rounding the fitting), throttle linkage, choke cable, and vacuum line. Reconnect the battery. Crank the engine — it should start with minimal cranking. Let it warm up and check the idle speed (550-600 RPM in Drive for automatic, 600-650 RPM for manual). Tuning Notes Idle Mixture: The idle mixture screw is pre-set but can be fine-tuned. With the engine warm, turn the screw in until the RPM drops, then back out 1/2 turn. Final setting should produce the highest steady idle. Float Level: Pre-set from the factory. If adjustment is needed: with the top removed and gasket in place, the float should be 1-5/32" from the gasket surface. Frequently Asked Questions Is this carburetor really pre-tuned? Yes. Each unit is bench-tested for proper float level, throttle plate operation, and base mixture setting before packaging. Most installations require only a minor idle speed adjustment to account for differences in engine condition, altitude, and transmission type. Will this fit a 170ci engine? This carburetor is calibrated for the 200ci (3.3L) inline-6. While it physically bolts onto a 170ci manifold, the jetting and venturi size may be slightly rich for the smaller displacement. It will run but may need re-jetting for optimal fuel economy on a 170ci engine. Does this fit a 1968 or later 200ci? 1968 and later Ford 200ci engines used different emissions equipment and carburetor designs. This carburetor is optimized for 1963-1967 non-emissions applications. It may physically fit later engines but linkage and vacuum port configurations differ. What's the difference between the 1100 and 1101? The Autolite 1101 is essentially the same carburetor with a slightly larger venturi and different jetting for higher-output applications. This unit works for both 1100 and 1101 replacement applications on the standard 200ci engine. Related Products iFJF Weber 32/36 Rebuild Kit Carburetor & Fuel System Collection Classic Ford Parts Collection

Read more less

Product Overview High-quality replacement carburetor designed as a direct fit for Massey Ferguson TE20, TO20, and TO30 tractors with Continental Z120 4-cylinder gasoline engines (1946-1954). Manufactured to match OEM 181643M91 specifications, this carburetor delivers reliable cold starts, smooth idle, and consistent fuel delivery for your vintage workhorse. Key Features Precision Tuned: Pre-calibrated fuel mixture for optimal performance across the Continental Z120 RPM range — no bench tuning required out of the box. OEM-Spec Construction: Cast aluminum body with brass internals matches original equipment dimensions and mounting points for hassle-free bolt-on installation. Complete Assembly: Arrives fully assembled with gaskets, float, needle valve, and throttle linkage — everything needed for installation in one box. Smooth Cold Starts: Optimized choke circuit and accelerator pump ensure reliable cold-weather starts and crisp throttle response. Durable Materials: Corrosion-resistant brass float and stainless steel hardware for long service life in agricultural environments. Compatibility Make Model Engine Year Massey Ferguson TE20, TO20, TO30 Continental Z120 4-Cylinder 1946-1954 Specifications Specification Detail Part Number 181643M91 Fitment Massey Ferguson TE20/TO20/TO30 (1946-1954) Engine Continental Z120 4-Cylinder Gasoline Material Cast Aluminum Body / Brass Internals Type Updraft Carburetor Why Choose iFJF At iFJF Direct, we specialize in quality aftermarket parts for tractors, diesel trucks, and agricultural equipment. Every product is manufactured to strict quality standards and backed by our 1-year warranty. We ship from our US warehouse with fast, tracked delivery — so you can get your tractor back to work sooner. Frequently Asked Questions Q: Will this carburetor fit my Massey Ferguson TO35?A: No, this carburetor is specifically designed for TE20, TO20, and TO30 models with the Continental Z120 engine (1946-1954). The TO35 uses a different engine and carburetor design. Please verify your tractor model before ordering. Q: Does it come with gaskets and mounting hardware?A: Yes, the carburetor arrives as a complete assembly including base gasket, mounting studs, and all necessary hardware for installation. Q: Is tuning required after installation?A: The carburetor comes pre-calibrated for standard operating conditions. Minor idle mixture adjustment may be needed based on your altitude and local climate. Basic mechanical knowledge is sufficient for installation. Q: What is your return policy?A: We offer a 30-day return policy for unused items in original packaging. If you receive a defective product, contact us immediately for a replacement or full refund. Q: How fast is shipping?A: Orders ship within 1-2 business days from our US warehouse. Standard shipping takes 3-7 business days. Expedited shipping options are available at checkout. Q: Do you offer warranty?A: Yes, all iFJF products come with a 1-year warranty against manufacturing defects. If you experience any issues, our support team will resolve them promptly. Order with Confidence Ready to get your Ferguson running smoothly again? Add to cart now and enjoy free shipping on orders $50+. Questions about fitment? Contact our support team — we respond within 24 hours and are happy to verify compatibility for your specific tractor model.

Read more less

Product Overview High-quality aftermarket 0-4412S Carburetor Replacement — precision-engineered for reliable fuel/air metering and direct bolt-on fitment. Manufactured to meet or exceed OEM specifications at a fraction of dealer pricing. Key Features Precision Manufacturing: CNC-machined components ensure exact tolerances and smooth throttle response OEM-Spec Materials: Constructed from durable die-cast aluminum and corrosion-resistant components that withstand high temperatures and fuel exposure Direct Fitment: Designed as a direct bolt-on replacement — no modifications or adapters required for installation Flow-Tested: Each unit undergoes quality control testing to verify proper fuel and air metering calibration Complete Assembly: Comes fully assembled and pre-adjusted for out-of-the-box installation — saves hours of setup time Compatibility Information This carburetor & fuel system is designed to replace the factory original equipment on compatible vehicles. Please verify your vehicle's year, make, model, and engine specifications before ordering. Contact our support team if you need assistance confirming fitment for your specific application. Technical Specifications Specification Details Product Type Carburetor & Fuel System Condition New Aftermarket Installation Direct Bolt-On Replacement Warranty 1-Year Replacement Warranty Shipping Same-Day on Orders Before 2 PM EST Why Choose iFJF Direct? At iFJF Direct, we specialize in high-quality aftermarket automotive parts for gasoline and diesel engines. Every product is sourced from trusted manufacturers and backed by our satisfaction guarantee. We stock inventory in our US warehouse and ship same-day on orders placed before 2 PM EST. Installation Tips Always disconnect the battery before starting any fuel system work Use new gaskets and seals — reusing old gaskets is the #1 cause of vacuum leaks and poor idle Double-check all linkage connections and throttle operation before starting the engine Perform a final fuel leak check after installation with the engine running at idle and under throttle Allow a short break-in period for gaskets to fully seat before final tuning adjustments Frequently Asked Questions Q: Will this fit my vehicle?A: Please verify your specific year, make, model, and engine against the compatibility information listed in the product title. If unsure, contact our support team with your VIN. Q: Is this a genuine OEM part?A: This is a high-quality aftermarket replacement manufactured to OEM specifications. It offers equivalent or superior performance at significantly lower cost than OEM dealer parts. Q: Does this come pre-tuned?A: Yes, the unit comes pre-adjusted from the factory for typical applications. Minor idle mixture and speed adjustments may be needed for your specific engine setup and altitude. Q: What's included in the box?A: The complete assembly as shown in product images, mounting gasket(s), and basic installation instructions. Verify included components match your application before installation. Q: What is your return policy?A: 30-day return policy for unused items in original packaging. Defective products covered under 1-year warranty. See our Returns page for full details.

Read more less

Product Overview Marine Electric Choke for Mercruiser 2-Barrel MerCarb 4.3L V6 70125A-1. Engineered for reliable performance and precision fitment, this iFJF aftermarket part meets or exceeds OEM specifications for durability and function. Ideal for DIY mechanics and professional technicians alike. Key Features Direct OEM Replacement: Engineered to match original Mercruiser MerCarb 2-barrel specifications exactly. Electric Choke Operation: Automatic temperature-controlled choke for reliable cold starts every time. Marine-Grade Construction: Corrosion-resistant materials designed for harsh marine environments. Plug-and-Play Installation: Pre-calibrated from factory — bolt on and go. Compatibility Year Make Model Engine/Notes See Description Marine Electric Choke for Mercruiser 2-Barrel MerC Direct Fit ⚠️ Always verify fitment with your specific vehicle year, make, model, and engine before ordering. Contact our support team for compatibility questions. Specifications Specification Value Brand iFJF Product Type Marine Carburetor Parts SKU FJ-CRRK-7665-4.3 Price $49.99 USD Type Electric Choke Application Marine — Mercruiser MerCarb 2-Barrel Why Choose iFJF? Quality Assurance: Every iFJF part undergoes rigorous quality inspection before shipping. Precision Engineering: Manufactured to tight tolerances for guaranteed fitment. Expert Support: Our team of diesel and automotive specialists is ready to help with any questions. Fast Shipping: Orders ship within 1-2 business days from our US warehouses. Frequently Asked Questions Q: Is this compatible with my Mercruiser engine?A: This electric choke is designed for Mercruiser MerCarb 2-barrel carburetors commonly found on 3.0L 4-cylinder and 4.3L V6 marine engines. Verify your carburetor model number before ordering. Q: How does an electric choke work?A: The electric choke uses a bi-metallic spring heated by 12V current. When cold, the spring holds the choke plate closed for rich starting mixture. As it heats up (30-90 seconds), the spring expands and opens the choke plate for normal running. Q: What are symptoms of a bad electric choke?A: Hard cold starts requiring excessive cranking, engine stalling when cold, black exhaust smoke (overly rich), poor fuel economy, and choke plate not opening fully after warm-up. Order your Marine Electric Choke today — fast shipping, expert support, and the quality you can trust from iFJF Direct. 📖 Related Guides & Articles 🔗 Marine Fuel Water Separator Guide: Why Your Outboard Needs One 🔗 How to Rebuild Edelbrock 1406 and 1405 Carburetors 🔍 Explore More Parts Looking for compatible parts? Browse our full selection of Marine Carburetor Parts for your vehicle or equipment. iFJF Direct offers quality aftermarket parts with fast shipping.

Read more less

Product Overview High-quality aftermarket 1 BBL Carburetor — precision-engineered for reliable fuel/air metering and direct bolt-on fitment. Manufactured to meet or exceed OEM specifications at a fraction of dealer pricing. Key Features Precision Manufacturing: CNC-machined components ensure exact tolerances and smooth throttle response OEM-Spec Materials: Constructed from durable die-cast aluminum and corrosion-resistant components that withstand high temperatures and fuel exposure Direct Fitment: Designed as a direct bolt-on replacement — no modifications or adapters required for installation Flow-Tested: Each unit undergoes quality control testing to verify proper fuel and air metering calibration Complete Assembly: Comes fully assembled and pre-adjusted for out-of-the-box installation — saves hours of setup time Compatibility Information This carburetor & fuel system is designed to replace the factory original equipment on compatible vehicles. Please verify your vehicle's year, make, model, and engine specifications before ordering. Contact our support team if you need assistance confirming fitment for your specific application. Technical Specifications Specification Details Product Type Carburetor & Fuel System Condition New Aftermarket Installation Direct Bolt-On Replacement Warranty 1-Year Replacement Warranty Shipping Same-Day on Orders Before 2 PM EST Why Choose iFJF Direct? At iFJF Direct, we specialize in high-quality aftermarket automotive parts for gasoline and diesel engines. Every product is sourced from trusted manufacturers and backed by our satisfaction guarantee. We stock inventory in our US warehouse and ship same-day on orders placed before 2 PM EST. Installation Tips Always disconnect the battery before starting any fuel system work Use new gaskets and seals — reusing old gaskets is the #1 cause of vacuum leaks and poor idle Double-check all linkage connections and throttle operation before starting the engine Perform a final fuel leak check after installation with the engine running at idle and under throttle Allow a short break-in period for gaskets to fully seat before final tuning adjustments Frequently Asked Questions Q: Will this fit my vehicle?A: Please verify your specific year, make, model, and engine against the compatibility information listed in the product title. If unsure, contact our support team with your VIN. Q: Is this a genuine OEM part?A: This is a high-quality aftermarket replacement manufactured to OEM specifications. It offers equivalent or superior performance at significantly lower cost than OEM dealer parts. Q: Does this come pre-tuned?A: Yes, the unit comes pre-adjusted from the factory for typical applications. Minor idle mixture and speed adjustments may be needed for your specific engine setup and altitude. Q: What's included in the box?A: The complete assembly as shown in product images, mounting gasket(s), and basic installation instructions. Verify included components match your application before installation. Q: What is your return policy?A: 30-day return policy for unused items in original packaging. Defective products covered under 1-year warranty. See our Returns page for full details.

Read more less

1946-1966 VW Beetle Bus Ghia 30 PICT-1 Carburetor — 12V Electric Choke Restore smooth idle, reliable cold starts, and hesitation-free acceleration to your classic Volkswagen. This 30 PICT-1 carburetor is a direct bolt-on replacement for 1946–1966 Beetle, Bus, Karmann Ghia and Standard models running 1300–1600cc single-port air-cooled engines — built to OEM dimensions with a 12V electric choke and anti-dieseling fuel cutoff. Key Takeaways ✅ Exact OEM Replacement: Directly replaces OE part numbers 113129027H / 113129027F. ✅ Reliable Cold Starts: 12V electric choke gets your engine firing on the first crank. ✅ Anti-Dieseling Safety: Built-in fuel cutoff solenoid stops engine run-on when you switch off. ✅ Durable Build: Aluminum alloy body, brass floats and stainless steel throttle shafts. ✅ Factory Calibrated: Airflow tested and leak tested before shipping — bolt-on ready. Features & Benefits Feature Benefit (What It Means for You) 12V Electric Choke Automatic cold-start enrichment — fires on the first crank without endless pedal pumping. Fuel Cutoff Solenoid Shuts off fuel instantly at ignition-off, preventing after-run, dieseling and hot-start trouble. Single-Barrel Downdraft Design Classic round-bowl architecture delivers consistent fuel atomization from idle to full throttle. Aluminum Alloy Body Anti-corrosion coated housing stands up to heat, vibration and years of daily driving. Brass Floats & Stainless Steel Shafts Eliminates float warping, throttle shaft wear and vacuum leaks over time. Threaded Fuel Inlet Secure, leak-resistant fuel line connection — an upgrade over loose press-in fittings. Compatibility & Cross-Reference Replaces OEM Part Numbers: Interchange Part Number Brand FJ-CBRT-LDH106 iFJF 113129027H VW OEM 113129027F VW OEM Common Applications (1300 / 1500 / 1600cc Single-Port): VW Beetle (Bug) — 1950–1966 VW Karmann Ghia — 1956–1966 VW Transporter / Bus / Kombi — 1949–1966 VW Standard — 1946–1948 Dune Buggy / Sand Rail / Baja Bug — custom, single-port upright engine ⚠️ Before ordering: ① Single-port manifold only — not compatible with dual-port manifolds (34 PICT-3). ② Requires a 12V electrical system; unrestored 6V cars need a 6V choke element or step-down resistor. ③ Check your year range above. Specifications Part Number FJ-CBRT-LDH106 (iFJF) Carburetor Type 30 PICT-1, single-barrel downdraft OE Part Numbers 113129027H / 113129027F Choke 12V electric choke Fuel Cutoff Built-in solenoid valve Body Material High-grade aluminum alloy, anti-corrosion coated Float / Throttle Shaft Brass float / stainless steel shaft Engine Fitment 1300 / 1500 / 1600cc single-port air-cooled (Type 1 & Type 2) Quality Control Airflow calibrated & leak tested Includes 2 mounting studs, 1 base gasket, 1 plug screw Why Choose iFJF? iFJF is a professional automotive parts manufacturer with 10+ years of experience. We design and build replacement parts that match — and often exceed — OEM specifications, so you get reliable, factory-grade performance without dealership markup. 🔬 Factory Airflow Calibration: Every unit is airflow calibrated to deliver consistent idle and acceleration out of the box. 🔍 100% Leak Tested: Fuel systems are pressure-tested before packaging to ensure zero leaks in service. 🛡️ Premium Build Quality: Aluminum alloy body, brass floats and stainless steel shafts for long-term reliability. 💰 Factory-Direct Supply: Commercial-grade quality straight from the manufacturer — no middleman markup. 🛡️ 1-Year Warranty Included · 30-Day Easy Returns · Lifetime Support Not satisfied? Return it. Fails prematurely? We'll replace it — no receipt-hoarding, no dealership runaround. Frequently Asked Questions Q: Will this fit my 6V VW? A: This carburetor uses a 12V electric choke. If your car is an original 6V system (pre-1967), you'll need to reuse the original 6V choke element or add a 6V step-down resistor, otherwise the choke won't open properly. Q: Which years and models does it fit? A: It fits 1946–1948 VW Standard, 1950–1966 Beetle, 1956–1966 Karmann Ghia and 1949–1966 Transporter/Bus, matched to 1300cc, 1500cc and 1600cc single-port engines. Please double-check your OE part number and manifold type before ordering. Q: Will it fit a dual-port engine? A: No — this carburetor is designed for single-port manifolds only. It is not compatible with dual-port manifolds (34 PICT-3). Please confirm your manifold type before ordering. Q: What is included in the package? A: You get 1 × 30 PICT-1 carburetor, 2 × mounting studs, 1 × high-temperature base gasket and 1 × fuel line plug screw — everything needed for a bolt-on install. Q: Is installation difficult? A: It's a direct bolt-on replacement with the same mounting as the original unit. While pre-calibrated, minor idle and mixture adjustment may be needed to match your altitude and distributor timing — normal for any carburetor replacement. Q: Why should I trust an iFJF carburetor? A: Every iFJF carburetor is factory airflow calibrated and leak tested before shipping, built from heavy-duty materials, and backed by a 1-year warranty with fast US-based support — no dealership runaround. Package Includes 1 × 30 PICT-1 Carburetor (12V electric choke) 2 × Mounting Studs 1 × High-Temperature Base Gasket 1 × Fuel Line Plug Screw Common Problems with Aftermarket Carburetors — Solved by iFJF We analyzed verified customer reviews of OEM and aftermarket alternatives. Here's what VW owners keep complaining about — and how we fixed it: ❌ What Owners Complain About ✅ How iFJF Solved It "The metal feels soft — parts wear out fast."— Common complaint in aftermarket reviews → Heavy-duty materials throughout.High-grade aluminum alloy body, brass floats and stainless steel throttle shafts resist wear and corrosion far longer than soft-metal clones. "There was machining debris in the idle circuit."— Common complaint in aftermarket reviews → Factory cleaned, calibrated & leak tested.Every unit is airflow calibrated and pressure leak tested before packaging, so the idle circuit runs clean right out of the box. "The choke never worked on my car."— Common complaint (12V/6V confusion) → Clear 12V spec + pre-order checklist.We state the 12V electric choke requirement up front and list the 6V conversion options, so you order the right voltage the first time. 🔎 We read the 1-star and 2-star reviews so you don't have to. Every iFJF product is engineered to solve the real problems owners actually face — not just match a spec sheet. Factory Direct Supply & Wholesale — iFJF is a direct manufacturer of high-performance automotive replacement parts, backed by ISO 9001:2015 and IATF 16949:2016 quality management system certifications. Custom specifications and bulk orders are highly welcome. Contact us for exclusive dealer pricing and volume discounts. Email: support@ifjf.net

Read more less

Product Overview The iFJF Tractor Carburetor for Ford New Holland is a complete ready-to-install replacement for Marvel Schebler TSX785 and TSX695 style carburetors on classic Ford tractors from 501 through 2000 Series. Delivers reliable starting, smooth idle, and consistent fuel delivery at a fraction of rebuilding a 60-year-old original. Key Features Complete Assembly: Fully assembled and pre-adjusted install straight out of the box. No rebuilding needed. OEM-Style Design: Faithful reproduction of Marvel Schebler TSX785/TSX695 with modern manufacturing precision. Broad Compatibility: Fits 501, 541, 601/611/621/631/641/651/661/671/681, 701/741/771, 2000 (1962-64), 2030, 2031, 2110, 2111, 2120, 2130, 2131. Pre-Calibrated: Factory fuel/air mixture set for out-of-box performance. Minor idle adjustments for altitude. Premium Construction: Quality castings, brass floats, durable gaskets ethanol-blend fuel compatible. Cross Reference Number Source 310746 Ford/New Holland B8NN9510A Ford/New Holland 312954 Ford/New Holland 1103-0003 Aftermarket Reference TSX785/TSX695 Marvel Schebler Specifications Type Updraft carburetor, TSX style Mounting 2-bolt flange Fuel Gasoline (ethanol compatible) Installation Direct bolt-on replacement Frequently Asked Questions Q: Will this fit my 1963 Ford 2000 4-cylinder?A: Yes! Direct replacement for 1962-1964 Ford 2000 Series 4-cyl gas. Cross-references with 310746, B8NN9510A, 312954. Q: Is this an original Marvel Schebler?A: High-quality aftermarket reproduction to TSX785/TSX695 specs. Reliable bolt-on performance at significantly lower cost. Q: Does it come with a gasket?A: Yes, includes mounting flange gasket. Always replace the gasket with a new carburetor for proper seal. Q: Do I need to adjust it before use?A: Pre-adjusted to factory baseline. Minor idle speed/mixture adjustments may optimize for your specific tractor. Related Products You May Need Carburetor Rebuild Kit Replacement for 1999-2005 Yamaha XL XLT GP 800 1200 iFJF TPS APPS Throttle Position Sensor Fit 53031575 98-07 Dodge RAM 2500 3500 5. Timing Chain Locking Wedge Tool for Ford Lincoln Mercury 5.4L & 4.6L 3V — 2005-2 Related Guides & Resources Classic Tractor Carburetor Tuning Ford Tractor Maintenance Guide

Read more less

Product Overview Fix your Yamaha Banshee's notorious TORS (Throttle Override System) issues once and for all with this complete TORS Removal Kit. If your Banshee is stalling, idling erratically, or bogging at part-throttle, the TORS parking brake limiter is the most likely culprit. This kit eliminates the problematic TORS system and gives you direct carburetor control. Compatible with 1987-2006 Yamaha Banshee 350 (all years). This is the #1 recommended modification for any Banshee — even stock machines benefit from TORS removal. Key Features Complete Kit — Includes idle screws, carb caps, and throttle cable caps Eliminates Stalling & Erratic Idle — No more TORS-related electrical gremlins Adjustable Idle — Manual idle adjustment screws give you full control Quick Install — 30-minute bolt-on modification, no fabrication required OEM-Quality Materials — Billet aluminum caps with proper O-ring seals What Is TORS & Why Remove It? TORS (Throttle Override System) is an early electronic safety system that monitors throttle position vs. carburetor slide position. When the parking brake microswitch gets dirty, the TORS brain box cuts ignition — causing stalling, bogging, and refusal to rev. On 30+ year-old machines, the wiring, brain box, and parking brake switch are almost certainly malfunctioning. This kit replaces the electronic TORS caps with manual idle screws, giving you direct, mechanical control over idle speed and eliminating all TORS-related electrical failures. Note: This kit is intended for off-road/competition use only. Not for street-legal vehicles. Compatibility Vehicle Years Engine Yamaha Banshee 350 1987–2006 347cc 2-Stroke Twin Kit Contents Component Quantity Idle Adjustment Screws 2 Carburetor Caps (TORS Delete) 2 Thumb Throttle Cable Caps 2 O-Rings & Hardware Complete Frequently Asked Questions Q: Will this completely eliminate my stalling issue?A: If your stalling is TORS-related (the most common cause on Banshees), yes. The TORS brain box and parking brake switch are the #1 cause of intermittent stalling on Banshees. If stalling persists after TORS removal, check your reeds, coil, stator, and carb jetting. Q: Is this difficult to install?A: No — this is a straightforward 30-minute bolt-on install. Remove the stock TORS carb caps, install the new caps + idle screws, replace the throttle cable caps, adjust idle, and you're done. Basic hand tools only. Q: Do I need to re-jet after TORS removal?A: Not necessarily. TORS removal doesn't change airflow or fuel delivery — it just replaces the electronic caps with manual ones. However, if your Banshee has other mods (pipes, air filter, etc.), you should already be jetted accordingly. Q: Can I leave the TORS brain box connected after installing this?A: You can physically leave it in place, but it will no longer have any function. Some riders remove it entirely to clean up the wiring. Unplug the parking brake switch connector as well. Q: Is this legal for street use?A: No. TORS is a safety system, and removing it makes the vehicle for off-road/competition use only. Not street legal in any jurisdiction. Related Products Browse All ATV & Powersports Parts Related Blog Posts Yamaha Banshee Common Problems & Fixes

Read more less

Overview The iFJF 799584 Carburetor is a direct-fit replacement for Briggs & Stratton 09P700 series engines found on walk-behind lawn mowers. Precision-calibrated for optimal fuel delivery, this carburetor restores reliable starting, smooth idling, and consistent power for 140cc 550EX, 625EX, and 675EX engines. Pre-adjusted from the factory for true plug-and-play installation — no tuning required. Key Features OEM-Spec Replacement: Manufactured to match Briggs & Stratton 799584 specifications for exact fitment on 09P700 series 140cc engines used across multiple mower brands. Broad Mower Compatibility: Fits Husqvarna LC 121P, Toro 550EX, Troy-Bilt TB110, Craftsman 247.372370, and many other walk-behind mowers using the BS 140cc engine platform. Factory Pre-Calibrated: Fuel mixture and idle settings are pre-adjusted at the factory. Install, add fresh fuel, and start mowing immediately — no carburetor tuning needed. Complete Assembly: Includes all gaskets, float bowl, needle valve, and internal components. Ready to bolt on right out of the box — no parts to transfer. Improved Fuel Economy: Optimized jetting and clean fuel passages ensure efficient combustion and reduced fuel consumption compared to worn-out carburetors. Easy 15-30 Minute Install: Direct bolt-on design with matching throttle and choke linkage points. Requires only basic hand tools — screwdriver set and socket wrench. Compatibility Engine/Brand Model Spec Briggs & Stratton 09P702 550EX 140cc Briggs & Stratton 09P702 625EX 140cc Briggs & Stratton 09P702 675EX 140cc Briggs & Stratton 09P702 725EXi 140cc Husqvarna LC 121P Push Mower Toro 550EX 140cc Mower Troy-Bilt TB110 Push Mower Craftsman 247.372370 Push Mower Specifications Specification Value Part Number 799584 Engine Series Briggs & Stratton 09P700 Engine Displacement 140cc Fuel Type Gasoline (E10 Compatible) Choke Type Auto-Choke (Thermal) SKU FJ-CBRT-584 Why Choose iFJF? At iFJF Direct, we specialize in high-quality replacement parts backed by rigorous quality control. Each carburetor is individually tested for proper float operation and fuel flow before shipping. We stand behind every product with responsive customer support and a satisfaction guarantee. A new carburetor is often more cost-effective than rebuilding a corroded, gummed-up original — and gets your mower running right the first time. Frequently Asked Questions Q: Will this fit my Briggs & Stratton 550EX engine?A: Yes. This carburetor is compatible with all Briggs & Stratton 09P700 series engines, including the 550EX, 625EX, 675EX, and 725EXi 140cc models. Check your engine model number on the valve cover. Q: Does this carburetor come with gaskets?A: Yes. The carburetor arrives as a complete assembly including all necessary gaskets, float bowl, needle valve, and internal components. No parts to transfer from your old carburetor. Q: Do I need to adjust anything after installation?A: This carburetor comes pre-calibrated from the factory. In most cases, no additional adjustment is required. Simply install it, add fresh fuel, and start mowing right away. Q: My mower is hard to start — will a new carburetor fix this?A: Hard starting is one of the most common symptoms of a dirty or failing carburetor. Clogged jets, stuck floats, and deteriorated gaskets are the usual culprits. Replacing with a new 799584 carburetor typically resolves these issues. Q: How long does installation take?A: For most DIYers, installation takes 15-30 minutes. You'll need basic hand tools (screwdriver set, socket wrench) and a clean, well-lit work area. Q: Is this compatible with ethanol-blended fuel (E10)?A: Yes, the carburetor is compatible with E10 fuel. However, we recommend using fuel stabilizer or draining the carburetor if the mower will be stored for more than 30 days, as ethanol can cause varnish buildup in any small engine carburetor. Package Includes 1 x 799584 Carburetor for BS 09P702 550EX 625EX 675EX 140cc Engine | Complete with gaskets & hardware | Product support documentation

Read more less

Product Overview The iFJF 1806 Performer 600 CFM carburetor delivers the ideal balance of street performance and daily driveability for small block and mild big block V8 engines. Featuring electric choke, air valve secondaries, and non-EGR calibration, this 4-barrel square bore carburetor is pre-calibrated for a wide range of engines from 305 to 402 cubic inches. Whether you're upgrading from a worn-out factory carb or building a fresh engine, the 1806 delivers out-of-the-box performance. Key Features 600 CFM — Universal Sweet Spot — The most versatile CFM rating for street V8s. Works well on everything from mild 305s to warmed-up 400s without over-carbureting. Air Valve Secondary — The secondary air valve opens progressively based on airflow demand. No bog, no hesitation — just smooth, seamless power delivery. Electric Choke (12V) — Automatic choke with adjustable housing. Fast warm-up, consistent cold starts in any season. Non-EGR Design — No exhaust gas recirculation provisions. Perfect for pre-emissions vehicles, off-road applications, or engines with EGR delete modifications. Two-Piece Aluminum Construction — Fewer gasket surfaces than three-piece designs. Resists warping and fuel leaks better than pot metal castings. Pre-Calibrated & Flow Tested — Each carburetor is wet-flow tested on a calibration engine before packaging. Ready to run with minimal tuning. Compatibility Engine Family Displacement Typical Vehicles Chevy Small Block 305, 327, 350, 383, 400 Camaro, Chevelle, C10, Nova, Impala, Monte Carlo Ford Windsor/Cleveland 302, 351W, 351C, 400M Mustang, F-150, Bronco, Torino, Cougar Mopar LA/Magnum 318, 340, 360 Charger, Challenger, Dart, Duster, Ram, Dakota AMC V8 304, 360, 390, 401 Javelin, AMX, CJ, Wagoneer, Cherokee Buick/Olds/Pontiac V8 301-403 Square bore intake required Specifications Parameter Value Part Number 1806 CFM Rating 600 CFM Barrel Type 4-Barrel Square Bore Choke 12V Electric Secondary Type Air Valve (Adjustable) Body Material Die-Cast Aluminum (Two-Piece) EGR Non-EGR (No EGR Provisions) Why iFJF Performer 1806? The 600 CFM Performer has been the go-to street performance carburetor for decades. Our 1806 builds on that legacy with modern manufacturing precision. The air valve secondary design is inherently smoother than mechanical secondaries for street driving — you don't get the sudden "hit" that can break tires loose unexpectedly on wet pavement. Combined with the 12V electric choke, this is the set-it-and-forget-it carburetor that starts reliably and drives smoothly from cold mornings to hot summer afternoons. Frequently Asked Questions Q: Will this fit my 350 Chevy with an Edelbrock Performer intake?A: Yes. The 1806 has a standard square bore flange that matches the Edelbrock Performer, Performer RPM, and most other aftermarket intakes. Direct bolt-on — no adapter needed. Q: What's air valve secondary vs. vacuum secondary?A: Air valve secondaries use a spring-loaded flap above the secondary throttle plates. As airflow increases, the valve opens progressively — providing smoother engagement than mechanical secondaries and more precise control than pure vacuum secondaries. Q: Will this work with my TH350 automatic transmission?A: Yes. The throttle lever includes provisions for GM TH350, TH400, 700R4, and 200-4R kickdown cables. Ford AOD and C4/C6 linkages are also supported with the correct bracket. Q: Does non-EGR mean it won't pass emissions?A: Non-EGR carburetors are intended for pre-emissions vehicles (generally pre-1975), off-road vehicles, or vehicles where the EGR system has been removed. Not for use on emissions-controlled vehicles where EGR is required by law. Q: Can I use this on a marine engine?A: No. Marine engines require USCG-approved carburetors with specific safety features (sealed overflow, J-tube venting). Use only marine-rated carburetors on boats. Q: What timing should I run with this carburetor?A: For most small block Chevy engines, start with 10-12° initial timing and 34-36° total mechanical advance by 3,000 RPM. Adjust vacuum advance to provide 10-12° additional under light cruise.

Read more less

Product Overview The iFJF 1901 Thunder AVS2 500 CFM carburetor is the next evolution in the Thunder carburetor lineup, featuring enhanced annular flow boosters for even finer fuel atomization. With 12V electric choke, non-EGR calibration, and a clean satin finish, this 4-barrel is purpose-built for small cubic-inch V8 and V6 engines where crisp throttle response matters more than maximum CFM. Ideal for restomods, street rods, and daily drivers with 260-327 CID engines. Key Features AVS2 Annular Boosters — Second-generation annular discharge booster design with improved fuel distribution across all 8 discharge holes. Noticeably smoother idle and better tip-in response than first-gen designs. 500 CFM Precision Calibration — Calibrated specifically for 260-327 CID small block V8s. Avoids the tuning headaches of oversized carburetors on small engines. Electric Choke — 12V automatic choke with adjustable housing. Cold starts in any weather without a manual choke cable. Non-EGR Design — No EGR port or provisions. Ideal for pre-emissions vehicles, off-road builds, and engines with EGR systems removed. Satin Finish Aluminum — Clean, understated appearance that doesn't yellow or discolor. Resists fuel staining and corrosion. Quick-Change Secondary Metering — Swap secondary rods in under 60 seconds with a screwdriver — no carb removal needed. Compatibility Engine Displacement Best Match Chevy Small Block 262-327 CID Mild street cam, stock heads, dual-plane intake Ford Windsor 260-302 CID Stock to mild build, great for early Mustangs Jeep V8 304-360 CID Good for Jeep CJ/Wagoneer with square bore manifold AMC V8 290-304 CID Direct fit on square bore aftermarket intakes Specifications Parameter Value Part Number 1901 CFM Rating 500 CFM Barrel Type 4-Barrel Square Bore Choke 12V Electric Primary Jet 0.095" Secondary Jet 0.095" EGR Non-EGR Finish Satin Aluminum Why AVS2? The AVS2 upgrades the classic Thunder/Edelbrock design with annular flow boosters — the same technology used in high-end racing carburetors. Instead of a single fuel discharge point, each booster has 8 precision-drilled holes that create a cone-shaped fuel mist. The result is more complete combustion at part throttle, smoother transitions, and fuel atomization that rivals EFI at a fraction of the cost. Frequently Asked Questions Q: What's the difference between AVS and AVS2?A: The AVS2 uses annular discharge boosters (8-hole ring) instead of standard down-leg boosters, providing finer fuel atomization. This results in smoother idle, better throttle response, and improved part-throttle fuel economy. Q: Does non-EGR mean I can't use it on a street car?A: Non-EGR simply means the carburetor does not have exhaust gas recirculation ports. It works perfectly on street cars — especially pre-1975 vehicles that didn't have EGR or vehicles where EGR has been removed for off-road use. Q: Can I use this on a 350 Chevy?A: A 500 CFM carburetor may be slightly restrictive for a built 350 at high RPM. For stock or mild 350s, it will work but may limit top-end power. For performance 350+ builds, consider our 600-650 CFM options. Q: Does this come with a fuel line and filter?A: A 5/8"-20 inlet fitting is included. The fuel line and inline filter are sold separately — we recommend a 3/8" braided line with serviceable filter. Q: How do I set the idle mixture?A: Start both mixture screws at 2 turns out. With engine warm and choke fully open, turn each screw in slowly until RPM drops, then back out 1/2 turn. Adjust idle speed to 700-800 RPM.

Read more less

Product Overview The iFJF 1801 Thunder AVS 500 CFM 4-barrel carburetor is purpose-calibrated for small displacement V8 and V6 engines. With annular discharge boosters, electric choke, and the signature Thunder AVS tunability, this carburetor delivers crisp throttle response and excellent driveability on engines from 260 to 327 cubic inches. Perfect for street rods, compact V8s, and mild cruiser builds. Key Features 500 CFM — Right-Sized — Properly sized for smaller displacement engines (260-327 CID). Avoids the low-speed drivability issues caused by over-carbureting with larger 600-750 CFM carbs. Electric Choke — Automatic 12V electric choke provides hassle-free cold starts. Heats up in 1-2 minutes and opens progressively — no manual cable to route. Annular Discharge Boosters — Eight-hole booster rings deliver superior fuel atomization at low airflow rates, critical for small engines that spend most of their time at part throttle. Tool-Free Secondary Tuning — Change secondary metering rods in seconds through the top of the carburetor. No disassembly required. Aluminum Body — Lightweight, corrosion-resistant, and runs cooler than cast iron. Factory pre-calibrated and wet-flow tested. Compatibility Engine Displacement Application Notes Chevy Small Block 262, 267, 283, 305, 307 Best for mild-cam street engines Ford Small Block 255, 260, 289, 302 Ideal for Mustang, Falcon, early F-100 Buick V6 / V8 231, 252, 260, 300 Fits square bore intake manifolds Chevy V6 (4.3L) 262 Requires 4-barrel intake manifold Jeep V8 304 Good match for CJ and Wagoneer builds Specifications Parameter Value Part Number 1801 CFM Rating 500 CFM Barrels 4-Barrel Square Bore Choke 12V Electric Choke Booster Type Annular Discharge Primary Jet 0.086" (factory) Secondary Jet 0.092" (factory) Body Material Die-Cast Aluminum Why 500 CFM? Small engines don't need big carbs. A 305 with a 750 CFM carb will have sluggish throttle response, poor fuel economy, and a weak vacuum signal that makes tuning impossible. The 1801 is designed and calibrated specifically for 260-327 CID engines. You'll get crisp off-idle response, stable idle, and excellent part-throttle manners — the things you actually feel when driving. Frequently Asked Questions Q: Is 500 CFM enough for my 305 Chevy?A: Yes. A 305 at 5,500 RPM requires approximately 485 CFM at 100% volumetric efficiency. The 500 CFM rating is ideal — it provides enough airflow without the sluggish low-speed response of an oversized carb. Q: How do I wire the electric choke?A: Connect the choke's positive terminal to a 12V ignition-switched source (only powered when the key is ON). Do NOT connect to the coil positive terminal. The choke housing grounds through the carburetor body. Q: Can I adjust the choke?A: Yes. Loosen the three screws on the choke housing and rotate it to adjust the opening rate. Turn toward "rich" (clockwise) for slower opening in cold weather; toward "lean" (counterclockwise) for faster opening in warm climates. Q: Will this fit a 2-barrel to 4-barrel conversion?A: Yes, as long as you use a 4-barrel square bore intake manifold. You cannot bolt a 4-barrel carb to a 2-barrel intake without an adapter (not recommended). Q: Is this carb compatible with EGR?A: This carburetor does not have EGR provisions. It is designed for non-EGR applications or vehicles with EGR systems deleted (for off-road/racing use only).

Read more less

2-Barrel 350 CFM Carburetor with Electric Choke Upgrade your classic muscle car, hot rod, or street machine with this 350 CFM 2-barrel carburetor featuring an electric choke. Designed as a direct performance replacement for the Holley 0-80350 2300 series, this carburetor delivers precise fuel metering, crisp throttle response, and hassle-free cold starts with its factory-preset electric choke. The vibration-polished aluminum body provides both a stunning show-quality finish and corrosion resistance for years of reliable service. Key Features Factory-Preset Electric Choke: No more wrestling with manual choke cables — automatic adjustment for smooth cold starts and fast warm-up. Optimized Street Calibration: Calibrated for excellent street manners with crisp throttle response and smooth idle. 350 CFM Airflow: Perfectly sized for mild to moderate V8 engines (283-350ci) and spirited inline-6 applications. Vibration-Polished Finish: Show-quality polished aluminum body that resists corrosion and looks great on any engine. Complete Package: Includes carburetor, fuel filter, metering jets, throttle linkage, fuel line, and necessary hardware. Specifications Specification Detail CFM Rating 350 CFM Barrels 2-Barrel (2300-Style Flange) Choke Type Electric (12V, Factory Preset) Main Jet Size #61 Main Power Valve 8.5 Accelerator Pump Nozzle #28 Vacuum Ports 1 Timed Spark Port + 1 PCV Port Material Aluminum Body, Brass Internals Why Choose iFJF? Plug-and-Play Electric Choke: Just connect 12V switched ignition — the choke does the rest. No cables, no adjustments. Holley 2300 Pattern: Fits standard 2-barrel intake manifolds — broad compatibility with GM, Ford, Mopar, and AMC V8s. Show-Ready Appearance: Vibration-polished finish looks as good as it performs. Frequently Asked Questions Q: Will this fit my Chevy 350 small block?A: Yes, with a 2-barrel intake manifold using the standard 2300-series flange. Ideal for mild 283-350ci small block V8s. Q: Does the electric choke need a separate power source?A: Yes. Connect to 12V switched ignition (hot only in RUN). Use a fused circuit — do NOT connect to the ignition coil. Q: Is this carburetor ready to run out of the box?A: Factory baseline calibration with preset electric choke. Minor idle mixture and speed adjustments may be needed for your engine. Q: How does this compare to the Holley 0-80350?A: Direct replacement manufactured to the same 2300 flange and calibration specs at a more affordable price point. Q: What air cleaner fits this carburetor?A: Any air cleaner designed for a standard Holley 2300 2-barrel flange. Air horn diameter is standard 2-barrel dimensions. Related Products More Carburetors & Fuel System Parts

Read more less

1406 600 CFM Performer Carburetor — Electric Choke, 4-Barrel Square Bore The iFJF 1406 Performer carburetor is a precision-engineered 600 CFM 4-barrel square bore carburetor with automatic electric choke — a direct replacement for the legendary Edelbrock 1406. Designed for street performance and mild race applications on 350-454ci V8 engines, this carburetor delivers crisp throttle response, consistent fuel metering, and hassle-free cold starts every time. Key Features 600 CFM Flow Rating: Optimized for street performance V8 engines from 350 to 454 cubic inches. Delivers excellent throttle response with good fuel economy at cruise. Automatic Electric Choke: 12V heating element progressively opens the choke plate — no cables, no manual intervention. Just turn the key and go. 4-Barrel Square Bore: Direct bolt-on for Edelbrock Performer, Performer RPM, and most OEM and aftermarket square bore intake manifolds. Vacuum Air Valve Secondary: Demand-based secondary opening prevents bog while delivering full CFM when you need it. Far more street-friendly than mechanical secondaries. Externally Tunable: Idle mixture screws, metering rods, step-up springs, and accelerator pump all accessible without removing the carburetor. No EGR Provision: Clean design without exhaust gas recirculation ports — ideal for pre-emissions vehicles and off-road/racing applications. Technical Specifications Specification Value CFM Rating 600 CFM @ 1.5 inHg Barrel Configuration 4-Barrel, Square Bore Choke Type Automatic Electric (12V) Secondary Type Vacuum Air Valve (Adjustable) Fuel Inlet Single 5/8"-20 UNF Throttle Bore Prim 1-7/16" / Sec 1-11/16" Float Level 7/16" from bowl top (idle) Fuel Pressure 5.5 psi maximum 1405 vs 1406: Which Should You Choose? Feature 1405 (Manual Choke) 1406 (Electric Choke) Choke Control Cable (driver-operated) Automatic (12V heated) Best For Race cars, off-road, hot rods Daily drivers, street cars, cruisers Cold Start Driver sets choke, adjusts as engine warms Automatic — turn key and go Wiring Required No (mechanical cable only) Yes (12V ignition-switched source) Calibration Slightly richer for cold-start control Slightly leaner for fuel economy Tuning & Setup Choke Adjustment: Rotate the black choke housing to adjust choke plate closure at cold. More rotation clockwise = richer cold mixture. Mark the factory position before adjusting. Fast Idle: With engine cold, set fast idle to 1,500-1,800 RPM via the fast idle screw on the throttle linkage. Idle Mixture: Warm engine fully. Using vacuum gauge, adjust each idle screw for peak vacuum, then back out 1/8 turn from lean best idle. Accelerator Pump: Three holes on the pump arm for different pump shot volume. Top hole = largest shot (for engines that bog on tip-in). Step-Up Springs: Factory 5" Hg (silver) spring works for most street engines. Lower vacuum camshafts need softer springs (3" or 4" Hg). Frequently Asked Questions Q: Should I get the 1405 or 1406 for my truck?A: For a daily-driven truck or any vehicle you want to start easily in all weather, the 1406 (electric choke) is the better choice. The 1405 (manual choke) requires installing a choke cable through the firewall and manual adjustment every cold start — better suited to dedicated race/off-road vehicles. Q: Where do I connect the electric choke wire?A: Connect to a 12V ignition-switched source — typically the ignition coil positive terminal, an IGN terminal on the fuse block, or the alternator field wire. DO NOT connect to the coil negative or to a constant 12V source (will drain battery). Q: Will this fit my Quadrajet intake?A: Quadrajet (spread bore) intakes require a square bore to spread bore adapter plate. Alternatively, consider an aftermarket dual-plane square bore intake manifold for best results. Q: Does this carb work at high altitude?A: The 1406 runs slightly rich at altitude. Above 5,000 feet, step down 1-2 jet sizes (factory primary jets: .098", secondary: .095"). For altitudes above 7,000 feet, consider a calibration kit with altitude-specific rods and jets. Q: What's included in the box?A: Complete assembled carburetor, mounting gasket, throttle ball stud, throttle return spring bracket, installation manual, and tuning reference chart. Related Products iFJF 1405 600 CFM Performer Carb — Manual Choke — Same carb with cable-operated manual choke 18-7665 Marine Electric Choke — Choke assembly for Mercruiser marine applications Related Blog Posts Complete Guide: How to Rebuild Edelbrock 1406 and 1405 Carburetors How To Rebuild Edelbrock 1406 and 1405 Carburetors | Rebuild Kit Links 1965-1967 Mustang 200ci Inline-6 Carburetor Replacement Guide

Read more less

1405 600 CFM Performer Carburetor — Manual Choke, 4-Barrel Square Bore The iFJF 1405 Performer carburetor is a precision-engineered 600 CFM 4-barrel square bore carburetor designed as a direct replacement and performance upgrade for the Edelbrock 1405. Ideal for small-block and mild big-block V8 engines from 350 to 450+ cubic inches, this manual choke carburetor delivers crisp throttle response, consistent fuel metering, and trouble-free operation — whether you're cruising on the street, towing, or hitting the track. Key Features 600 CFM Flow Rating: Optimized for street performance and mild race applications on 350-454ci V8 engines. Ideal airflow for dual-plane intake manifolds. Manual Choke: Driver-controlled cold-start enrichment — eliminates the complexity of electric choke wiring and provides positive choke control in all weather conditions. 4-Barrel Square Bore Design: Direct bolt-on for Edelbrock Performer, Performer RPM, and most OEM square bore intake manifolds. No adapter required. Air Valve Secondary: Vacuum-operated secondary air valve opens progressively based on engine demand — no bog, no hesitation, just smooth power delivery. No EGR Provision: Clean, simple design without EGR ports — ideal for off-road, racing, or pre-emissions vehicles. For off-road and racing use only where emissions equipment is not required. Tunable Without Disassembly: Externally adjustable idle mixture screws and easily accessible metering rods and jets enable tuning without removing the carburetor from the manifold. Technical Specifications Specification Value CFM Rating 600 CFM @ 1.5 inHg Barrel Configuration 4-Barrel, Square Bore Choke Type Manual (cable-operated) Secondary Type Vacuum-Controlled Air Valve Fuel Inlet Single 5/8"-20 UNF Throttle Bore Diameter Primary 1-7/16", Secondary 1-11/16" Mounting Flange Square Bore (5-1/8" x 5-5/8") Finish Satin Silver / Natural Aluminum Recommended Fuel Pressure 5.5 psi maximum (regulator recommended) Compatibility Guide Engine Family Displacement Application Notes Small Block Chevy 305-400 ci Excellent match for mild 350 builds with dual-plane intake Small Block Ford 289-351 ci Ideal for 302/351W street performance Big Block Chevy 396-454 ci Suitable for mild street BBC — may be slightly small for high-RPM 454+ AMC V8 304-401 ci Popular upgrade for AMC 360/401 Chrysler LA/Magnum 318-360 ci Requires square bore intake or adapter Why Choose the 1405 Manual Choke Carburetor? The manual choke design offers several advantages over automatic chokes for performance applications. You get positive, immediate choke control without waiting for an electric element to heat up — essential for engines with aggressive camshafts that need precise cold-start enrichment. The manual cable setup also eliminates a potential failure point (burned-out electric choke) and reduces electrical load on your charging system. For race cars, off-road vehicles, and hot rods where simplicity is key, the manual choke 1405 is the go-to choice. Tuning Guide Idle Mixture: Start with both idle mixture screws 1.5 turns out. Warm engine fully. Adjust each screw for highest vacuum reading, then back out 1/8 turn for best idle quality. Idle Speed: Set curb idle to 700-800 RPM (manual trans) or 650-750 RPM (auto in drive). Verify timing is set correctly before adjusting carb. Metering Rods & Jets: Factory calibration works well for most 350-400ci street engines. For altitude (>5,000 ft), step down one jet size. For high-compression builds, step up one rod size richer. Secondary Air Valve: Adjust pre-load spring tension via the set screw on the passenger side. Lighter tension = earlier secondary opening. Too light = bog. Too heavy = sluggish top end. Float Level: Fuel level should be 7/16" from the top of the float bowl with the engine idling. Adjust via the external needle & seat assembly — no bowl removal needed. Fuel Pressure: Edelbrock-style carbs are sensitive to fuel pressure. Use a regulator set to 5.5 psi maximum. Higher pressure will force the needle off the seat and flood the engine. Frequently Asked Questions Q: What's the difference between the 1405 and 1406 carburetors?A: The 1405 uses a manual choke (cable-operated), while the 1406 uses an electric choke (automatic, 12V). The 1405 is preferred for race cars, off-road vehicles, and applications where the driver wants full choke control. The 1406 is better for daily drivers and street cars where automatic cold-start convenience is desired. Q: Do I need a square bore to spread bore adapter?A: If your intake manifold is a spread bore design (Q-jet pattern), yes. If it's a square bore (Holley/Edelbrock pattern), no. Most aftermarket dual-plane intakes (Edelbrock Performer, Weiand Action Plus, etc.) are square bore and accept this carburetor directly. Q: Will this carburetor work with my stock hood?A: The 1405/1406 has a relatively low profile compared to Holley double pumpers and Dominator carbs. In most applications with a stock or mild drop-base air cleaner, hood clearance is not an issue. Measure from the intake manifold carb pad to the hood for verification. Q: What fuel pump do I need?A: A standard mechanical fuel pump (5-7 psi) with a regulator set to 5.5 psi maximum is ideal. Electric pumps must also be regulated. Do NOT exceed 6.0 psi — these carbs are highly sensitive to over-pressurization. Q: Is this carburetor emissions-legal for street use?A: This carburetor does not have EGR provisions and is intended for off-road, racing, and pre-emissions (pre-1975) vehicles. Check your local emissions regulations before installing on a street-driven vehicle. Related Products iFJF 1406 600 CFM Performer Carburetor — Electric Choke — Same carb with automatic electric choke 18-7665 Marine Electric Choke for Mercruiser — Choke assembly for marine applications Related Blog Posts Complete Guide: How to Rebuild Edelbrock 1406 and 1405 Carburetors (Step by Step) How To Rebuild Edelbrock 1406 and 1405 Carburetors | Rebuild Kit Links 1965-1967 Mustang 200ci Inline-6 Carburetor Replacement Guide

Read more less

Product Overview Get your small engine running like new with the iFJF 594287 Carburetor Replacement Kit. This complete carburetor assembly is designed as a direct replacement for 796608 and 799248 engine carburetors, featuring a built-in thermostat choke for reliable cold starts. The kit includes all necessary gaskets and a new spark plug — everything you need for a complete fuel system refresh. A failing carburetor causes hard starts, poor idle, surging, and reduced power. Rather than rebuilding an old, worn-out unit, this brand new assembly offers a quick, cost-effective solution that gets your equipment back to full performance in under an hour. Key Features Complete Kit: Carburetor + thermostat choke + gaskets + spark plug — all in one box Thermostat Choke: Automatic choke adjusts based on engine temperature for reliable cold starts Pre-Calibrated: Factory-set fuel mixture — install and go, minimal adjustment needed Direct Bolt-On: Matches 594287 mounting pattern and linkage connections exactly Quality Construction: Precision-cast aluminum body with brass fuel fittings for durability 📋 Compatibility Compatible Engines Briggs & Stratton engines using 594287 carburetor 796608 engine series 799248 engine series Various generators, pressure washers, lawn tractors with compatible mounting 📐 Specifications Specification Value Part Number 594287 Replaces 796608, 799248 Choke Type Thermostat (automatic) Included Carburetor, gaskets, spark plug Material Aluminum body, brass internals ❓ Frequently Asked Questions Q: Will this fit my generator?A: If your generator uses a Briggs & Stratton engine with carburetor part numbers 594287, 796608, or 799248, this will fit. Check your engine model number on the engine shroud to confirm. Q: Does it come pre-adjusted?A: Yes. The carburetor is factory pre-set for the correct air-fuel mixture. Minor idle speed adjustment may be needed depending on your altitude and application. Q: What's included in the kit?A: The kit includes the carburetor assembly with thermostat choke, all mounting gaskets, and a compatible spark plug. Q: Do I need special tools to install?A: Basic hand tools (socket set, screwdrivers) are sufficient. No special carburetor adjustment tools required for most installations. Q: Why replace instead of rebuild?A: A new carburetor ensures all internal passages are clean and undamaged. Rebuilding an old carburetor can't fix internal corrosion or worn throttle shafts. New replacement is faster and more reliable.

Read more less

Product Overview Replacement choke pulloff vacuum brake for carbureted engines. Replaces CPA38, 101-492A, and CPA87. This vacuum-operated diaphragm controls the choke plate during cold starts — a failed pulloff causes hard starting, rough idle, black smoke, and poor cold drivability. Direct bolt-on replacement restores proper cold-start enrichment and smooth warm-up in under 15 minutes. Key Features OEM-Spec Vacuum Diaphragm — Manufactured to OEM specifications for consistent, reliable choke plate control during cold starts and warm-up. Direct Replacement — Replaces CPA38, 101-492A, CPA87 — bolts in place with no modifications, adapters, or fabrication. Smooth Cold Starts Restored — Eliminates hard starting, rough cold idle, black exhaust smoke, and stumbling on cold engines. Universal Carburetor Fit — Compatible with Rochester, Holley, and Carter carburetors using vacuum-operated choke pulloffs. 15-Minute Installation — Single vacuum line and two screws — typical install under 15 minutes with basic hand tools. Compatibility Make Model Year Range Notes GM / Chevrolet Rochester 2G / 4G 1960s–1980s CPA38 Style Pulloff Various Holley 2-Barrel / 4-Barrel Universal Vacuum Choke Pulloff Various Carter AFB / AVS Universal Vacuum Choke Pulloff Specifications Specification Value Part Numbers CPA38 / 101-492A / CPA87 Type Vacuum Diaphragm Choke Pulloff Connection Single Vacuum Port Mounting Standard 2-Screw Flange Frequently Asked Questions Q: How do I know if my choke pulloff is bad?A: Symptoms: hard cold starting, rough idle until warm, black exhaust smoke, choke plate doesn't open smoothly. Test: apply vacuum — rod should retract smoothly and hold. Q: Will this fit my carburetor?A: Fits most Rochester, Holley, and Carter carburetors with vacuum choke pulloff and standard 2-screw flange. Q: How do I install it?A: Remove old pulloff (2 screws + vacuum line), mount new unit, reconnect vacuum line. Under 15 minutes. Q: What's the difference between CPA38 and CPA87?A: Both are vacuum choke pulloffs with similar specs but slightly different linkage arms. This replacement is compatible with both. Q: Can a bad choke pulloff cause poor fuel economy?A: Yes. A stuck-closed choke makes the engine run rich constantly — wasting fuel and fouling plugs. Replacement can significantly improve MPG. Related Products Related carburetor parts: 4-Barrel Carburetor 500 CFM (9904 square flange), Carburetor Rebuild Kit for complete overhaul, and Fuel Filter Element for clean fuel delivery.

Read more less

Product Overview 3PCS Carb Rebuild Kit for 398729 396701 392061 9-37107 18-7222 18-7042 18 20 30 40 75HP Outboard Motors With Float — a direct-fit replacement carburetor engineered to restore proper fuel delivery and engine performance. Pre-calibrated and tested for reliable fuel metering across the RPM range — ideal for rebuilds, restorations, and troubleshooting. Key Features Direct Bolt-On: Pre-calibrated, ready to install — matches OEM mounting points, throttle linkage, and fuel inlet. Precision Fuel Metering: Factory-set air/fuel mixture for optimal idle, throttle response, and fuel economy. Durable Construction: Die-cast aluminum body with corrosion-resistant finish — handles ethanol-blended fuels. Complete Assembly: All internal components pre-assembled and tested — floats, jets, needles, gaskets. Versatile Application: Compatible with listed ATVs, UTVs, go-karts, dirt bikes, and small engine applications. Specifications Parameter Specification Type Standard Barrel Single Condition Brand New — Pre-Assembled Fuel Type Gasoline (E10 compatible) Installation Tips Clean surfaces: Remove old gasket material before install. Check float level: Verify float height matches specification. Prime fuel system: Fill float bowl before first start. Adjust idle mixture: Fine-tune at operating temperature. Use fresh fuel: Stale fuel is the #1 cause of carburetor problems. Frequently Asked Questions Q: Is this carburetor pre-tuned?A: Yes, factory baseline jetting. Fine-tuning may be needed for your altitude and engine mods. Q: Will this fit my engine?A: Check product title for compatible makes/models. Verify intake bolt pattern and throttle linkage match. Q: Do I need to re-jet for altitude?A: Above 3,000 ft, smaller main jets may be needed (1-2 sizes per 3,000 ft gain). Q: Does this come with gaskets?A: Yes, base gasket included. Most include O-rings and additional seals. Q: How do I break in a new carb?A: No special break-in. Install, prime, start, set idle. Re-check bolts after first heat cycle. Q: What fuel should I use?A: Fresh 87+ octane gasoline. Avoid >10% ethanol. Drain float bowl for storage or use fuel stabilizer. Shop with Confidence Get your engine running right. Ships fast from US warehouse. Contact support for fitment questions.

Read more less

Product Overview The iFJF Carburetor Rebuild Kit for 398729 396701 392061 9-37107 18-7222 18-7042 18 20 30 40 75HP Outboard Motors With Float is a premium aftermarket replacement engineered to meet or exceed OEM specifications. Replaces OEM part 18-7222 / 18-7042. Manufactured with precision tooling and quality materials, this direct-fit component restores factory function at a fraction of the dealership cost. Whether you are refreshing a daily driver, completing a restoration, or performing routine maintenance, this iFJF part delivers dependable performance backed by US-based customer support. Key Features Complete Rebuild Kit — Includes all gaskets, seals, O-rings, float, and needle & seat for a thorough carburetor refresh. Precision-Engineered Components — Manufactured to OEM tolerances for reliable fuel metering and smooth operation. Ethanol-Resistant Materials — Modern gasket compounds resist swelling and degradation from E10 ethanol-blended fuels. One Kit, Multiple OEM Numbers — Cross-references several original equipment part numbers for broad compatibility. DIY-Friendly Installation — Comprehensive kit with everything needed for a successful rebuild in 1-2 hours. Specifications Spec Value Replaces OEM 18-7222 / 18-7042 Brand iFJF Condition New Why Choose iFJF iFJF replacement parts are engineered to match or exceed OEM quality at a fraction of the price. Every component undergoes rigorous quality control before shipping. Our products are designed with the DIY mechanic in mind — direct fit, complete with all necessary hardware, and backed by responsive US-based customer support. Do not settle for no-name generic parts. Choose iFJF for quality you can trust. Installation Tips Remove the old carburetor — drain fuel, disconnect lines and linkage. Take reference photos first. Clean the mounting surface on the intake manifold to ensure a proper seal. Transfer any reusable hardware (throttle cable bracket, choke linkage) to the new carb. Mount the new carburetor with new gaskets. Tighten bolts evenly — do not overtighten. Reconnect fuel line and linkage. Prime the fuel system and check for leaks. Start the engine and allow it to warm up. Fine-tune idle mixture if needed. Frequently Asked Questions Q: Does this replace OEM part 18-7222?A: Yes. This aftermarket replacement is built to match or exceed the specifications of OEM part 18-7222. Direct bolt-on — no modifications required. Q: How difficult is the installation?A: Installation is rated as a DIY-friendly job for anyone with basic mechanical skills and common hand tools. Most customers complete the installation in 30-90 minutes. Professional installation is always an option if you are not comfortable with DIY auto repair. Q: What warranty is included?A: All iFJF products are backed by our satisfaction guarantee. If you experience any issues with fitment or quality, contact our US-based support team for a prompt resolution — replacement or refund. Q: How does this compare to the OEM part?A: Our aftermarket replacement is built to the same dimensional specifications as the OEM part using equivalent or upgraded materials. We focus on fixing known OEM weaknesses — like replacing plastic components with metal where the original design commonly fails. Related Products Carburetor Rebuild Kit Replacement for 1999-2005 Y Carburetor Honda TRX 400 FourTrax Sportrax TRX400X

Read more less

Product Overview The 1403 Performer 500 CFM 4-Barrel Carburetor Electric Choke Golden is engineered for diesel enthusiasts seeking improved engine performance and reliability. This complete delete solution removes restrictive EGR components, resulting in lower EGTs, cleaner intake airflow, and improved throttle response. **For off-road/competition use only.** Key Features ✓ Performance Improvement: Removes exhaust gas recirculation restrictions for lower EGTs, improved throttle response, and cleaner intake airflow. ✓ CNC-Machined Components: Precision-cut plates and plugs from billet aluminum ensure perfect sealing and corrosion resistance. ✓ Complete Hardware Kit: Includes all gaskets, bolts, O-rings, and plugs required for installation — no trips to the hardware store. ✓ Heavy-Duty Construction: Components rated for extreme diesel operating temperatures and pressures — built to last the life of your engine. ✓ Off-Road Use: Designed for competition and off-road vehicles where EGR systems are not required by regulation. Technical Specifications Material Billet 6061-T6 Aluminum Finish Natural / Anodized Components Plates, Plugs, Gaskets, Bolts, O-Rings Application Diesel Engine Performance Installation Professional Installation Recommended Usage Off-Road / Competition Only Why Choose iFJF? Quality Assurance: Every product undergoes rigorous quality inspection before shipping. USA-Based Inventory: Products ship from our US warehouse — no waiting for international freight. Expert Support: Our team knows diesel, automotive, and RV parts. Real answers from real people. Fair Pricing: Premium quality without the premium markup — direct value to you. Hassle-Free Returns: 30-day return policy. If it doesn't fit or meet your expectations, we'll make it right. Installation Tips Disconnect battery before starting Allow engine to cool completely Reference factory service manual for torque specs Replace all gaskets — never reuse old ones Professional installation recommended for this modification Frequently Asked Questions Q: What are the benefits of an EGR delete?A: EGR delete removes the exhaust gas recirculation system, which can reduce intake carbon buildup, lower EGTs, improve throttle response, and potentially increase fuel economy. These components are for off-road use only. Q: Is this legal for street use?A: No. EGR delete kits are intended for off-road, competition, and agricultural use only. They are not compliant with on-highway emissions regulations in the United States or Canada. Q: Do I need a tuner after installing this kit?A: Yes. After installing an EGR delete kit, you must reprogram the ECM with appropriate tuning to prevent check engine lights and ensure proper engine operation. Q: How difficult is the installation?A: Installation difficulty varies by vehicle. Most kits require 3-6 hours with basic hand tools. Professional installation is recommended. A factory service manual is helpful. Q: Will this void my warranty?A: Modifying emissions control systems may affect your factory warranty coverage. Check with your dealer or review the Magnuson-Moss Warranty Act for details. Q: What material are the block-off plates made from?A: Our plates are CNC-machined from billet 6061-T6 aluminum for superior strength, corrosion resistance, and perfect flatness for leak-free sealing. Related Products Related Blog Posts

Read more less

Product Overview The iFJF 1901R Quadrajet 4MV 750 CFM carburetor is a premium replacement for 1968-1973 Chevrolet and GMC trucks equipped with 327, 350, 396, 402, and 454 V8 engines. Featuring vacuum secondaries, manual choke, and a distinctive golden finish, this carburetor delivers the legendary Quadrajet spread-bore design in a brand new, ready-to-run package — no core charge, no rebuilding hassles. Key Features 750 CFM Spread-Bore Design — Small primaries for fuel economy and crisp part-throttle response; massive secondaries for full-throttle power when towing or hauling. Vacuum Secondary Operation — Secondaries open only when the engine demands it, preventing bogging and improving fuel economy compared to mechanical secondary carbs. Manual Choke — Cable-operated choke for reliable cold starts. Simple mechanical operation with no vacuum diaphragms or electrical connections to fail. Golden Chromate Finish — Corrosion-resistant coating that maintains its appearance and protects the aluminum body from fuel degradation and oxidation. Complete Assembly — Pre-calibrated and wet-flow tested. Includes base gasket and mounting hardware. Compatibility Year Make Models Engine 1968-1972 Chevrolet C10, C20, C30, K10, K20, K30 327, 350, 396, 402, 454 1973 Chevrolet C10, C20, C30, K10, K20 350, 454 1968-1972 GMC 1500, 2500, 3500, C15, C25, K15, K25 327, 350, 396, 402 1973 GMC 1500, 2500, C15, C25, K15, K25 350, 454 1968-1973 Chevrolet Suburban, Blazer 350, 396, 454 Specifications Parameter Value Part Number 1901R OEM Cross-Reference 7026202, 7026203, 7026210, 7027202, 7027203, 7042202 CFM Rating 750 CFM Barrel Configuration 4-Barrel (Spread Bore / Square Bore Compatible) Choke Type Manual Choke Secondary Vacuum-Operated Air Valve Body Material Die-Cast Aluminum (Golden Chromate) Why iFJF 1901R for Your Classic Truck? The Quadrajet was GM's workhorse carburetor for over two decades. But original units are now 50+ years old — warped air horns, leaking well plugs, and worn throttle shafts are common problems. Our 1901R gives you the legendary Quadrajet design with modern manufacturing: precision CNC-machined metering circuits, properly sealed well plugs, and a brand new casting that hasn't been through 50 years of heat cycling. The result is a carburetor that starts easier, idles smoother, and delivers the fuel economy these trucks were known for when new. Frequently Asked Questions Q: Will this fit my 1970 C10 with a 350?A: Yes, this is a direct replacement for your 1970 C10 350. The 1901R bolts to the factory Quadrajet intake manifold and uses the same throttle linkage and fuel line connection. Q: Do I need to change my intake manifold?A: No. The 1901R fits the factory cast iron Quadrajet intake manifold found on 1968-1973 GM trucks. No adapter needed. Q: How do I connect the throttle linkage?A: The throttle lever accepts the factory GM throttle cable and transmission kickdown cable (TH350/TH400). The geometry matches OEM specifications. Q: Is this carburetor good for towing?A: Absolutely. The Quadrajet's small primaries provide excellent fuel economy during cruise while the massive secondaries deliver full power for towing and hauling heavy loads. Q: Can I convert this to electric choke?A: This model is manual choke only by design. If you prefer electric choke, see our other Quadrajet-style options. Q: What fuel pressure do I need?A: 5-6 PSI maximum. Stock mechanical fuel pumps are ideal. If using an electric pump, install a regulator set to 5 PSI.

Read more less

Product Overview The iFJF 18990035 Weber 44 IDF carburetor is a premium replacement for 1968-1979 Volkswagen Beetle, Super Beetle, and Transporter (Bus) models with the 1.6L air-cooled engine. Featuring dual 44mm throttle bores, this 2-barrel downdraft carburetor delivers significantly improved throttle response, horsepower, and tunability compared to the stock Solex carburetor. Complete with integrated air horn and striking golden finish. Key Features 44mm Dual Throttle Bores — 44mm barrels provide ample airflow for modified 1600cc engines, including those with bigger camshafts, ported heads, or increased displacement (1776cc, 1915cc). Direct Solex Replacement — Same downdraft configuration as the factory Solex 34 PICT carburetor. Bolts to the stock intake manifold center section. Complete Assembly with Air Horn — Includes integrated air horn for cleaner intake airflow and better filtration mounting. Genuine Weber IDF Design — Based on the legendary Weber IDF circuit with tunable idle jets, main jets, air correction jets, and emulsion tubes — giving you full control over fuel calibration. Golden Finish — Corrosion-resistant golden chromate coating that looks as good as it performs. Tunable Accelerator Pump — Adjustable pump stroke for customizing tip-in fuel delivery. Compatibility Year Model Engine 1968-1979 VW Beetle (Type 1) 1.6L 1584cc H4 1971-1979 VW Super Beetle 1.6L 1584cc H4 1968-1971 VW Transporter Type 2 (211/215/261/265) 1.6L 1584cc H4 1968-1974 VW Karmann Ghia 1.6L 1584cc H4 1968-1973 VW Type 3 (Fastback/Squareback) 1.6L 1584cc H4 (center mount only) Specifications Parameter Value OEM Part Numbers 18990035, 18990030, 18990.035V Carburetor Type 2-Barrel Downdraft (Weber IDF) Throttle Bore 44mm (x2) Venturi Size 36mm Mounting Pattern Standard IDF/Centro-Mount Choke None (performance carburetor) Fuel Inlet M10x1.0 Banjo Fitting Why Upgrade to Weber IDF? The factory Solex 34 PICT-3 carburetor was adequate when new but is now notorious for warped throttle bodies, clogged idle circuits, and difficult cold starts. The Weber IDF design has been the gold standard for air-cooled VW performance since the 1970s. It offers superior tunability with replaceable jets, a more robust accelerator pump circuit, and dramatically improved throttle response. Whether you're restoring a daily driver or building a weekend cruiser, this carburetor transforms how your vintage VW drives. Installation Tips Use new paper gaskets on both sides of the phenolic spacer block Set idle mixture screws at 1 turn out from seated as starting point Verify fuel pressure at 2.5-3.0 PSI — mechanical pumps may need a regulator Base idle speed: 850-900 RPM on air-cooled engines Check for vacuum leaks at intake boots and manifold end castings before tuning With a 009 mechanical advance distributor, set timing to 28-32° BTDC at 3000+ RPM Frequently Asked Questions Q: Will this fit my 1974 Super Beetle with stock engine?A: Yes. The 18990035 Weber 44 IDF is a direct bolt-on replacement for the stock Solex carburetor on your 1974 Super Beetle 1600cc. It bolts to the factory intake manifold center section. Q: Do I need to change my distributor when installing this carburetor?A: The Weber 44 IDF works well with both vacuum-advance (SVDA) and centrifugal-advance (009) distributors. If using a 009, make sure the vacuum port on the carb is capped. Q: Is this carburetor too big for a stock 1600cc engine?A: The 44 IDF is properly sized for stock to mild 1600cc engines when properly jetted. It comes pre-calibrated for 1600cc. If upgrading to 1776cc or larger, you may want to increase main jet sizes. Q: What air filter fits on this carburetor?A: The integrated air horn accepts standard IDF-style air filter assemblies. Low-profile oval filters (commonly available for Beetle engine bays) fit perfectly. Q: Does this carburetor work with dual carb setups?A: This carburetor is designed for single center-mount applications. For dual carb setups, consider dual 40 IDF or 44 IDF kits with appropriate manifolds. Q: Will I need to re-jet for my elevation?A: At elevations above 4,000 ft, you may want to reduce main jet size by 5-10 numbers. Below 4,000 ft, the factory jetting will work well.

Read more less

Product Overview 40 IDF Carburetor for Weber 40mm Carb 2 Barrel Beetle Car Air Horn (Golden) — a direct-fit replacement carburetor engineered to restore proper fuel delivery and engine performance. Pre-calibrated and tested for reliable fuel metering across the RPM range — ideal for rebuilds, restorations, and troubleshooting. Key Features Direct Bolt-On: Pre-calibrated, ready to install — matches OEM mounting points, throttle linkage, and fuel inlet. Precision Fuel Metering: Factory-set air/fuel mixture for optimal idle, throttle response, and fuel economy. Durable Construction: Die-cast aluminum body with corrosion-resistant finish — handles ethanol-blended fuels. Complete Assembly: All internal components pre-assembled and tested — floats, jets, needles, gaskets. Versatile Application: Compatible with listed ATVs, UTVs, go-karts, dirt bikes, and small engine applications. Specifications Parameter Specification Type Weber IDF-Style Barrel 2-Barrel Condition Brand New — Pre-Assembled Fuel Type Gasoline (E10 compatible) Installation Tips Clean surfaces: Remove old gasket material before install. Check float level: Verify float height matches specification. Prime fuel system: Fill float bowl before first start. Adjust idle mixture: Fine-tune at operating temperature. Use fresh fuel: Stale fuel is the #1 cause of carburetor problems. Frequently Asked Questions Q: Is this carburetor pre-tuned?A: Yes, factory baseline jetting. Fine-tuning may be needed for your altitude and engine mods. Q: Will this fit my engine?A: Check product title for compatible makes/models. Verify intake bolt pattern and throttle linkage match. Q: Do I need to re-jet for altitude?A: Above 3,000 ft, smaller main jets may be needed (1-2 sizes per 3,000 ft gain). Q: Does this come with gaskets?A: Yes, base gasket included. Most include O-rings and additional seals. Q: How do I break in a new carb?A: No special break-in. Install, prime, start, set idle. Re-check bolts after first heat cycle. Q: What fuel should I use?A: Fresh 87+ octane gasoline. Avoid >10% ethanol. Drain float bowl for storage or use fuel stabilizer. Shop with Confidence Get your engine running right. Ships fast from US warehouse. Contact support for fitment questions.

Read more less