iFJF 322-3154 Fuel Filter for Cat 312E 320D2 320E 324E 329E Excavators
Overview The 322-3154 Fuel Filter is engineered for Caterpillar's mid-size excavator lineup — the machines that power construction, mining, and earthmoving operations worldwide. This spin-on filter provides dual-stage protection: particulate filtration plus water separation, ensuring clean fuel delivery to your Cat engine's high-pressure common rail injection system. Compatible with C4.4, C6.6, and C7.1 ACERT engines across the 312E through 329E series. Key Features Genuine CAT-Spec Filtration: 4-micron absolute rating protects high-pressure injectors from wear Water Separation: Integrated hydrophobic media strips emulsified water from diesel fuel Heavy-Duty Construction: Reinforced steel canister withstands high-vibration excavator environments Broad Excavator Coverage: Fits 312E, 315E, 320D2, 320E, 324E, 329E, and more Extended Service Life: 500-hour service interval under normal operating conditions Compatibility Table Equipment Engine Series Cat 312E Excavator C4.4 ACERT E-Series Cat 315E Excavator C4.4 ACERT E-Series Cat 320D2 Excavator C6.6 ACERT D2-Series Cat 320E Excavator C6.6 / C7.1 ACERT E-Series Cat 324E Excavator C7.1 ACERT E-Series Cat 329E Excavator C7.1 ACERT E-Series Cat 2384C/2484C Loader C6.6 ACERT C-Series Specifications Spec Value Part Number 322-3154 Filter Type Spin-On Fuel/Water Separator Micron Rating 4 micron absolute Thread Size M16 × 1.5 Service Interval 500 hours (normal) / 250 hours (severe duty) Why iFJF for Heavy Equipment? Every filter batch-tested for burst pressure and filtration efficiency per ISO 4548 Anti-drainback valve prevents dry starts after filter changes Save 40-60% vs CAT dealer pricing — same protection, smarter fleet management Bulk pricing for fleet and rental companies — contact us FAQ Q: Will this fit my Cat 320DL?A: The 320DL typically uses a different fuel filter configuration. This 322-3154 is designed for the D2 and E-series excavators. Check your operator's manual or contact us with your machine serial number for verification. Q: How often should I drain the water separator?A: Check the water-in-fuel (WIF) sensor daily. Drain any accumulated water immediately. Even small amounts of water can damage common rail injectors — the #1 cause of Cat fuel system failure. Q: Can I use this on Cat generators?A: Only if your generator set uses the same C4.4/C6.6/C7.1 engine platform and filter head. Always verify by part number cross-reference before ordering.
$179.99
iFJF 3316872.900 RV Refrigerator Control Panel for Dometic DM2672 DM2872
3316872.900 RV Refrigerator Control Panel for Dometic DM2672 & DM2872 — Restores ON/OFF, AUTO/GAS and Temperature Control The iFJF 3316872.900 eyebrow control panel is a direct plug-in replacement for the Dometic Americana II DM2672 and DM2872 two-way (120V AC / LP gas) RV refrigerators. It carries the ON/OFF button, the temperature up/down buttons, the AUTO/GAS mode selector and the AUTO and CHECK indicator lights, and it connects to the refrigerator's existing ribbon harness with no wire splicing and no soldering. This panel replaces Dometic part numbers 3316872.900 and 3316872900 — the same board written with and without the catalog dot. 📋 Key Takeaways ✅ Direct OEM Replacement: Replaces Dometic 3316872.900 / 3316872900 with the same footprint, the same connector keying and the same button positions as the original eyebrow board. ✅ Full Panel Function Restored: ON/OFF, temperature up and down, and the AUTO/GAS mode switch all work again, so the refrigerator can be set from the eye-level panel instead of a service call. ✅ Correct Indicator Behaviour: The AUTO lamp lights when the refrigerator runs on shore power and the CHECK lamp warns on a gas lockout — exactly as the Dometic Americana II control logic intends. ✅ Plug-and-Play Harness: The existing ribbon connector plugs straight into the new board; no cutting, crimping or soldering is required. ✅ ABS Housing with Sealed Button Membrane: The molded ABS carrier and the sealed membrane resist road vibration and interior cleaning chemicals. ✅ Fits 2-Way Americana II Fridges: Built for DM2672 and DM2872 models that run on 120V AC and LP gas. Features & Benefits Feature Benefit (What It Means for You) Dometic 3316872.900 fitment Bolt-in replacement for the failed eyebrow board, so the refrigerator keeps the panel layout the rest of the coach was built around. Three-function button set Power, temperature and AUTO/GAS mode are all on one panel again — no workaround switches and no guessing which mode the fridge is in. AUTO and CHECK indicators You can see at a glance whether the refrigerator is on AC power or has dropped into a gas fault, which shortens roadside troubleshooting. Sealed ribbon connector The factory-style connector keeps the signal path to the lower power board stable under vibration, preventing intermittent button response. ABS carrier and membrane overlay Resists UV fade, cracking and cleaning sprays, so the printed legends stay readable season after season. Plug-and-play install About 15–20 minutes with a screwdriver — disconnect power, swap the board, reconnect the harness and test every mode. Compatibility & Cross-Reference Replaces OEM Part Numbers: Interchange Part Number Brand 3316872.900 Dometic 3316872900 Dometic Fits These Refrigerators: Brand Model Power Configuration Dometic DM2672 2-Way (120V AC / LP Gas) Dometic DM2872 2-Way (120V AC / LP Gas) Common Applications: Class A motorhomes with a Dometic Americana II DM2872 refrigerator — the 8 cu. ft. two-door model Fifth wheels and travel trailers with a Dometic Americana II DM2672 refrigerator — the 6 cu. ft. two-door model Any DM2672 or DM2872 coach whose eyebrow board is dead, flickering or refusing to change mode Specifications Part Number 3316872.900 (also listed as 3316872900) Component Type Front interface (eyebrow) control panel with circuit board Power Configuration 2-Way — 120V AC / LP Gas Control Circuit 12V DC Controls ON/OFF, temperature up/down, AUTO / GAS mode selection Indicators AUTO, CHECK Housing Material ABS plastic with sealed button membrane Item Weight 5.3 oz (150 g) Package Dimensions 9.65 × 1.97 × 1.57 in (24.5 × 5.0 × 4.0 cm) Warranty iFJF Quality Guarantee Signs the 3316872.900 Panel Has Failed The eyebrow panel lights are out, dim or flickering while the refrigerator still cools Buttons do not respond, or the temperature setting will not change The refrigerator will not switch between AUTO (AC) and GAS The CHECK lamp stays on after a gas lockout and the panel cannot be reset The panel works only after a sharp tap on the housing — a classic cracked-solder symptom Before replacing the board, confirm 12V DC is present at the refrigerator and check the fuse on the lower power board — a blown fuse can make a healthy eyebrow panel look dead. Installation Tips Isolate all three power sources: unplug from shore power, disconnect the 12V DC battery feed and shut off the LP gas at the tank. Remove the eyebrow trim: the panel surround is held by clips or screws at the top edge of the refrigerator. Photograph the connector: take a picture of the ribbon cable orientation before unplugging it from the old board. Swap the board: release the old 3316872.900 panel, seat the new one in the same opening and reconnect the harness. Reinstall the trim and restore power: turn on LP gas, reconnect 12V DC, then plug into shore power. Test every mode: cycle ON/OFF, raise and lower the temperature setpoint, and confirm the AUTO and CHECK lamps behave correctly in both AC and GAS. Why Choose iFJF 🛡️ Quality Guarantee · Easy Returns · Wiring Support Not satisfied? Return it. Fails prematurely? We'll replace it — no receipt-hoarding, no dealership runaround. Our control boards are built to match the OEM footprint, connector keying and button legends, so the replacement drops into the same opening without drilling, filing or adapter harnesses. Every unit is produced under an ISO 9001:2015 and IATF 16949:2016 certified quality management system, and every shipment is checked for panel fit and connector alignment before it leaves the warehouse. 🔌 Connector-Verified: Each board is checked against the original ribbon connector so it seats fully on the first attempt. 🛡️ Vibration-Ready Build: ABS carrier and sealed membrane are chosen for the constant road vibration an RV appliance sees. 💰 Factory-Direct Supply: The same fit and function as the OEM board without dealership parts-counter markup. Looking for a different Dometic eyebrow panel? Check out the 3316995900 control panel kit for RM2354 RM2454 RM2554 DM2663 here → 🛒 Frequently Bought Together: 3850964036 Refrigerator Button Panel Kit — the eyebrow board for Dometic RM1350, RM3762 and RM3962 2-way refrigerators 2932771021 / 2932771039 Control Panel Kit — the panel used on DM2652, DM2852, RM2351 and RM2551 models 📂 Browse More: All Electronics Products → Frequently Asked Questions Q: Will the 3316872.900 control panel fit my Dometic DM2672 refrigerator? A: Yes. The 3316872.900 eyebrow control panel is the direct replacement for the Dometic Americana II DM2672 and DM2872 two-way refrigerators. Match the part number printed on your existing board or in the refrigerator's parts list before ordering — these are the only two models this panel is built for. Q: What symptoms mean the 3316872.900 panel has failed? A: Replace the 3316872.900 panel when the eyebrow lights are out or flickering, the buttons no longer respond or will not change the temperature setting, the refrigerator refuses to switch between AUTO and GAS, or the CHECK lamp will not clear. A panel that only responds after a tap on the housing is a failing board as well. Q: Is 3316872.900 the same part as 3316872900? A: Yes. 3316872.900 and 3316872900 are the same Dometic part number written with and without the catalog dot. Both refer to the two-way eyebrow control panel used on the DM2672 and DM2872 Americana II refrigerators, and this board replaces either number. Q: How difficult is it to install the 3316872.900 control panel? A: The 3316872.900 control panel is a plug-and-play replacement that takes about 15–20 minutes with a screwdriver. Unplug shore power, disconnect the 12V DC battery feed, shut off the LP gas at the tank, remove the eyebrow trim, photograph and unplug the ribbon connector, swap the board, then reconnect everything and test AUTO and GAS modes. Q: Will the 3316872.900 panel fix a refrigerator that runs but will not cool? A: No. The 3316872.900 panel only restores the user interface — power, temperature setting, mode selection and the AUTO/CHECK lamps. If the buttons work but the refrigerator does not cool on either AC or gas, the fault is more likely in the lower power board, the heating element or the cooling unit rather than the eyebrow panel. Q: What is included with the 3316872.900 control panel kit? A: The kit includes the assembled 3316872.900 eyebrow control panel with its circuit board and printed button membrane. It plugs into the refrigerator's existing ribbon harness, so no soldering, crimping or adapter harness is needed; the original mounting hardware is reused. Factory Direct Supply & Wholesale — iFJF is a direct manufacturer of high-performance automotive and outdoor filtration systems and RV replacement electronics. Custom specifications and bulk orders are highly welcome. Contact us for exclusive dealer pricing and volume discounts. Backed by ISO 9001:2015 and IATF 16949:2016 quality management system certifications. Email: support@ifjf.com
$67.99
iFJF 34 PICT-3 Carburetor for 1971-1979 VW Beetle Super Beetle — 1600cc Dual Port Electric Choke
34 PICT-3 Carburetor for 1971-1979 VW Beetle & Super Beetle — 1600cc Dual Port Restore your classic Volkswagen's performance with this 34 PICT-3 reproduction carburetor from iFJF Direct. Precision-engineered for the 1600cc dual port air-cooled engine, this carburetor delivers the smooth idle, crisp throttle response, and reliable cold starts your vintage VW deserves. Key Features Exact 34 PICT-3 Reproduction: Manufactured to replicate the original Solex 34 PICT-3 specifications — bolt pattern, venturi sizing, and jetting match OEM specifications for the 1600cc dual port engine. 12V Electric Choke: Pre-installed automatic electric choke ensures reliable cold starts. Connect to a switched 12V ignition source for hands-free warm-up enrichment. Improved Throttle Response: Precision-machined throttle shaft and venturi provide crisp, immediate throttle response — a noticeable upgrade over worn 50-year-old original carbs. Complete Ready-to-Install: Arrives fully assembled with electric choke, mounting gasket, and baseline adjustments set for immediate startup and driving. Classic VW Compatibility: Fits 1971-1979 Beetle, Super Beetle, 1973-1974 Thing, and 1971-1974 Karmann Ghia with 1600cc dual port engines. Compatibility Make Model Years Engine Volkswagen Beetle 1971-1979 1600cc Dual Port Volkswagen Super Beetle 1971-1979 1600cc Dual Port Volkswagen Thing (Type 181) 1973-1974 1600cc Dual Port Volkswagen Karmann Ghia 1971-1974 1600cc Dual Port Specifications Specification Value Carburetor Type 34 PICT-3 (Solex reproduction) Choke Type 12V Electric (automatic) Engine 1600cc Dual Port Air-Cooled Replaces Part # 113129031K, 34PICT-3 Barrels Single barrel, progressive Why Choose iFJF Direct? Our 34 PICT-3 reproduction is built to tight tolerances using quality materials that stand up to modern ethanol-blended fuels. Every unit is inspected before shipping. Satisfaction guaranteed. Frequently Asked Questions Q: Will this fit my VW Beetle?A: This 34 PICT-3 carburetor fits 1971-1979 Volkswagen Beetle and Super Beetle with the 1600cc dual port engine. It also fits 1973-1974 VW Thing and 1971-1974 VW Karmann Ghia with the same engine configuration.Q: Is this a genuine Solex carburetor?A: This is a high-quality reproduction of the Solex 34 PICT-3 carburetor, manufactured to OEM specifications. It provides the same fit, function, and performance as the original at a more accessible price point.Q: Does it come with the electric choke?A: Yes — this carburetor includes the 12V electric choke assembly pre-installed. Simply connect the choke wire to a 12V switched ignition source for automatic cold-start enrichment.Q: Is it pre-adjusted out of the box?A: The carburetor comes with baseline settings that should allow the engine to start and run. Fine-tuning of idle speed, idle mixture, and choke adjustment will be needed for optimal performance on your specific engine.Q: What gaskets are included?A: The carburetor includes the base gasket for mounting to the intake manifold. We recommend also replacing your intake manifold gaskets and fuel line during installation for best results. Order today and get your classic VW running right. Free shipping on orders $50+.
$253.99
iFJF 34117 Waste Ball Valve Seal Kit for Aqua Magic Style II, Style Lite, Style Plus RV Toilets
Overview The iFJF 34117 Waste Ball Valve Seal Kit is a direct replacement for the critical sealing component in Aqua Magic Style II, Style Lite, and Style Plus RV toilets. The waste ball valve seal creates the watertight barrier between your toilet bowl and the black water holding tank — when it fails, you get persistent odors, water leakage, and an unpleasant living environment in your RV or camper. Over time, the factory rubber seal hardens, cracks, or loses elasticity due to exposure to chemicals, temperature extremes, and mechanical wear from the flush ball mechanism. This affordable seal kit restores a tight, odor-free seal without the expense of replacing the entire toilet assembly ($200-400 for a new RV toilet). Installation takes about 30 minutes with basic hand tools. Key Features Direct OEM Replacement — Compatible with Aqua Magic Style II, Style Lite, Style Plus, and related Thetford RV toilet models Stops Odors & Leaks — Restores the water seal that prevents black tank odors from entering your RV living space Durable Rubber Construction — Manufactured from chemical-resistant rubber compound that withstands RV toilet chemicals and holding tank treatments Complete Kit — Includes ball valve seal, O-rings, and necessary gaskets for a thorough rebuild DIY-Friendly — Replace in approximately 30 minutes with basic hand tools; no special plumbing skills required Save $200+ — A $10-15 seal kit vs. $200-400 for a new RV toilet assembly Technical Specifications Specification Details Part Number 34117 Compatible Toilets Thetford Aqua Magic Style II, Style Lite, Style Plus Material Chemical-Resistant Rubber Compound Includes Waste Ball Valve Seal, O-Rings, Gaskets Installation Time Approx. 30 Minutes Compatibility Toilet Model Compatibility Aqua Magic Style II ✅ Direct Fit Aqua Magic Style Lite ✅ Direct Fit Aqua Magic Style Plus ✅ Direct Fit Other Thetford Residential-Style RV Toilets ✅ May Fit — Verify Design Installation Guide Turn Off Water — Shut off water supply to the RV toilet Empty & Clean Bowl — Flush and thoroughly clean the toilet bowl and flush ball area Remove Old Seal — Access the waste ball valve area (typically by removing the toilet from the floor flange or accessing through the bowl), extract the old hardened seal Clean Seal Groove — Remove all debris, mineral deposits, and old seal residue from the seal groove Install New Seal — Press the new iFJF 34117 seal into the groove, ensuring even seating around the entire circumference Reassemble & Test — Reinstall toilet if removed, restore water, fill bowl, and check for leaks and proper seal operation FAQ Q: How do I know if my waste ball valve seal needs replacement?A: Signs of a failing seal include: water in the toilet bowl draining slowly or not holding at all, persistent sewer odors in the RV bathroom, visible cracking or hardening of the rubber seal (visible when looking at the flush ball area), or the toilet requiring more frequent water refills to maintain the bowl seal. Q: Can I replace the seal without removing the toilet from the floor?A: On most Aqua Magic models, the seal is accessible from above after removing the flush ball mechanism — the toilet does not need to be removed from the floor flange. However, access is tight and removing the toilet (just two floor bolts) can make the job significantly easier. Q: How long should an RV toilet ball valve seal last?A: With regular use, expect 2-5 years from a quality seal. Factors that shorten seal life include: frequent use of harsh chemical holding tank treatments, extreme temperature swings (winter storage freeze-thaw cycles), and failure to maintain water in the bowl (a dry seal cracks faster). Q: Will this stop my toilet from holding water?A: If the water loss is caused by a worn ball valve seal, yes. If the toilet bowl itself is cracked or the flush ball is damaged, those are separate issues requiring different repairs. The majority of "toilet won't hold water" complaints in RV toilets are seal-related. Q: Do I need any special lubricant for the new seal?A: We recommend applying a thin coat of silicone-based plumber's grease or Thetford-approved seal lubricant to the new seal before installation. This protects the rubber, ensures smooth flush ball operation, and extends seal life. Never use petroleum-based lubricants as they degrade rubber. Q: Is this the same as Thetford part 34117?A: Yes. This aftermarket seal is manufactured to the same specifications as Thetford OEM part 34117 and provides equivalent fit and durability at a more accessible price point. Q: Can I use chemical treatments with this seal?A: Yes. The seal material is formulated to resist standard RV holding tank chemicals. For maximum seal longevity, avoid pouring undiluted chemicals directly onto the seal. Add treatments to the holding tank through the toilet bowl with water running. Q: What if the new seal still doesn't hold water?A: If the problem persists after installing a new seal, check: (1) The flush ball surface for scratches or damage that prevents sealing, (2) Proper seal seating in the groove (fully pressed in, no twists), (3) The toilet bowl itself for hairline cracks. The flush ball may also need replacement if heavily scratched. 📚 Related Guides & Articles iFJF Guides & Resources — Expert Tips, Installation Tutorials & Buying Guides
$39.99
iFJF 349-5327 12V Fuel Extraction Pump for Perkins 804C-33 & CAT
349-5327 12V Electric Fuel Extraction Pump for Perkins & CAT Diesel Engines When the fuel transfer pump on your Perkins or Caterpillar engine fails, the machine doesn't run — period. This 12V electric fuel extraction pump is a direct replacement for the 349-5327 OEM unit found on Perkins 800 Series and CAT compact diesel engines. Designed for generators, compact construction equipment, marine auxiliary engines, and industrial power units — anywhere a Perkins 800-series or equivalent CAT engine provides the power. 🔌 12V Electric — Self-Priming: This is an electric fuel pump, not a mechanical lift pump. It requires 12V DC power (typically from the engine's electrical system or a dedicated circuit). Self-priming design eliminates the need for manual bleeding in most installations. Key Features Direct OEM Replacement — Engineered as a bolt-on replacement for Perkins 349-5327 and MP10325 fuel transfer pumps. Matches OEM mounting pattern, fuel line connections, and electrical connector specifications. 12V DC Electric Operation — Self-priming electric pump delivers consistent fuel flow regardless of engine RPM — unlike mechanical pumps that lose efficiency at low idle. Critical for generators that run at constant RPM but need reliable starting fuel delivery. Wide Cross-Reference Coverage — Replaces 349-5327, MP10325, 232-5877, 228-9130, 228-9129, and many more. Compatible with Perkins 804C-33, 804C-33T, 804D-33, 804D-33T, 422E, 432D, 3044C, 259B3, 279C, 279C2, 289C engine models. Corrosion-Resistant Construction — Aluminum pump body with stainless steel internal components. Designed to withstand the vibration, heat, and fuel chemistry of diesel engine compartments in generator enclosures, engine bays, and machinery frames. Pre-Set Output Pressure — Factory-calibrated output pressure matches Perkins/CAT fuel system specifications. No regulator adjustment needed for standard installations. Compatibility Engine Family Models Typical Applications Perkins 800 Series 804C-33, 804C-33T, 804D-33, 804D-33T Generators, compact wheel loaders, telehandlers, mobile compressors Perkins 400 Series 422E, 432D Compact excavators, skid steers, aerial work platforms Perkins 3000 Series 3044C Marine auxiliary engines, industrial power packs CAT Compact 259B3, 279C, 279C2, 289C Compact track loaders, multi-terrain loaders Cross-Reference Part Numbers Brand Part Numbers Perkins (OEM) 349-5327, MP10325 CAT 232-5877, 228-9130, 228-9129 Specifications Specification Value Voltage 12V DC Pump Type Electric diaphragm / gear pump Fuel Compatibility Diesel (standard and biodiesel up to B20) Mounting Direct bolt-on — matches OEM mounting pattern Self-Priming Yes Why This Pump Fails and When to Replace Electric fuel pumps in industrial and generator applications fail for predictable reasons: (1) Contaminated fuel — running without a properly maintained primary filter allows debris to score the pump's internal surfaces. (2) Water in fuel — causes internal corrosion on the electric motor windings and check valves. (3) Continuous operation — generator pumps that run for thousands of hours between services experience normal brush/motor wear. (4) Voltage issues — low battery voltage or poor ground connections cause the pump motor to overheat. If your engine cranks but won't start, or starts and then dies after a few seconds, test the fuel pump output before replacing injection components. Frequently Asked Questions Q: How do I confirm this pump fits my Perkins engine?A: Check your engine's data plate for the model number. If it's an 804C-33, 804C-33T, 804D-33, 804D-33T, 422E, 432D, or 3044C — or a CAT 259B3/279C/279C2/289C — this pump is compatible. Visually compare the mounting flange, fuel line positions, and electrical connector to the product images before ordering. Q: Is this a mechanical or electric pump?A: This is a 12V electric pump. It requires a 12V DC power supply. It is NOT a mechanical lift pump driven by the engine camshaft. Most Perkins 800-series engines use electric lift pumps — verify your engine's configuration before ordering. Q: Do I need to bleed the fuel system after installation?A: This pump is self-priming, so in most installations it will draw fuel and purge air on its own. For stubborn air locks (common after a complete system drain), loosen the injection pump inlet fitting until fuel appears, then tighten and attempt to start. Never use starting fluid on a diesel engine. Q: What causes these pumps to fail — and how do I prevent it?A: Water contamination and dirty fuel are the top two killers. Always maintain your primary fuel filter/water separator. Check for water in the fuel system monthly if the equipment is stored outdoors or runs seasonally. A fuel pressure gauge on the output side can warn you of declining pump performance before it fails completely. Product Overview 349-5327 12V Fuel Extraction Pump for Perkins 804C-33 & CAT is a premium-quality replacement component engineered for exact fitment and reliable performance. Manufactured to meet or exceed OEM specifications using high-grade materials, this part delivers dependable service life for your equipment. Why Choose iFJF Direct iFJF Direct specializes in premium replacement parts for diesel trucks, RVs, marine, pool & spa, and automotive applications. Every product is backed by our commitment to quality, fast US-based shipping, and responsive customer support. We source directly from IATF 16949-certified manufacturers to bring you OEM-equivalent quality at competitive prices.
$79.99
iFJF 350157 Union Kit for Pentair SuperFlo Pool & Spa Pumps — with Gasket | iFJF
Product Overview The 350157 Union Kit for Pentair SuperFlo Pool & Spa Pumps — with Gasket | iFJF is a precision-engineered replacement part designed to restore proper function and stop leaks in your pool or spa equipment. Manufactured to meet or exceed OEM specifications, this component delivers reliable, long-lasting performance at a fraction of the dealer price. Pool equipment operates in a harsh environment — constant exposure to chlorinated water, UV radiation, temperature swings, and pressure cycles. When seals, O-rings, and internal components degrade, the result is leaks, poor filtration, and higher operating costs. Key Features OEM-Spec Precision: Manufactured to exact dimensional tolerances for guaranteed fit without modifications. Chemical-Resistant Materials: EPDM, Viton, or chemical-grade polymers resist degradation from chlorine, bromine, salt, and UV. Extended Service Life: Premium materials deliver 2-3x the service life of economy alternatives. Easy DIY Installation: Straightforward replacement with basic hand tools — most jobs take 15-30 minutes. Value Pack Savings: Multi-pack options available — stock up and save vs buying singles when applicable. Compatibility Specification Detail Brand Pentair Pool & Spa Replaces Part # 350157, SW-21-350, 21063-350-000 Material EPDM Rubber / Engineered Polymer Application Residential & Light Commercial Pool/Spa When to Replace Visible Leaks: Water seeping from connections or housings = failed seal or gasket Decreased Performance: Reduced flow, poor filtration = worn internal components Unusual Noise: Grinding or squealing = worn bearings, gears, or impellers Age: Rubber seals should be replaced every 2-3 years as preventive maintenance Hard/Cracked Rubber: O-rings that feel hard or show surface cracks no longer seal properly Installation Tips Turn Off Equipment: Switch off at circuit breaker before working on pool equipment. Release Pressure: Open air relief valve on filter to release system pressure. Clean All Surfaces: Remove old gasket material and debris — clean surface = proper seal. Use Proper Lubricant: Silicone-based pool lube only. NEVER use petroleum jelly — it destroys EPDM. Tighten Evenly: Cross-pattern tightening for multi-bolt connections. Test Before Full Operation: Run briefly and check all connections. Frequently Asked Questions Q: Does this fit my SuperFlo VS pump?A: Yes. Fits all Pentair SuperFlo pumps: VS (variable speed), single-speed, two-speed, and high-performance models. Replaces OEM part numbers 350157, SW-21-350, and 21063-350-000. Q: What is included in the kit?A: One 2-inch union connector nut (threaded half), one 2-inch union tailpiece (slip half), and one EPDM gasket/O-ring. Single union set for one pump port. Most SuperFlo pumps need two kits (suction and discharge). Q: How do I stop my pump from leaking at the union?A: Common causes: 1) Over-tightening crushes gasket (hand-tighten + 1/4 turn only) 2) Old hardened gasket (replace every 3 years) 3) Misaligned pipe stress (support plumbing within 12 inches of pump) 4) Cracked union nut from freeze damage or overtightening. Q: Can I install without cutting plumbing?A: If replacing existing same-type union: yes. Unscrew old nut, swap gasket, reconnect. If tailpiece (glued half) needs replacement, you will need to cut and re-glue PVC pipe using primer and cement rated for pool/spa applications. Related Products Shop All Pool & Spa Parts → Pool Filter Cartridges & Grids → Related Guides & Articles Pool Filter Maintenance: Complete Seasonal Guide → How to Fix Common Pool Pump Problems →
$37.99
iFJF 3514635 3585502 Rear Wheel Bearing Kit for Polaris Ranger 400-900 4x4
3514635 3585502 Rear Wheel Bearing Kit — Polaris Ranger 400-900 4x4 The 3514635 3585502 Rear Wheel Bearing Kit is a complete rear wheel bearing replacement set engineered for Polaris ATV and UTV models. Restore smooth wheel rotation, eliminate grinding noise, and fix excessive wheel play with this direct-fit bearing kit. Whether you're servicing a workhorse Ranger or prepping for the trail, fresh bearings mean safer, more predictable handling — and no seized hubs in the backcountry. Key Features Complete Replacement Set: Includes all bearings, seals, and snap rings needed for a full rear wheel bearing service — both sides. Precision-Ground Races: Heat-treated chrome steel (GCr15) bearings with precision-ground races for smooth rotation and long service life under heavy loads. Double-Lip Seals: Upgraded double-lip rubber seals keep water, mud, and sand out significantly better than single-lip seals — critical for ATV/UTV use. Pre-Packed Grease: Bearings come pre-packed with high-temp, water-resistant lithium complex grease — ready to install out of the box. Direct OEM Replacement: Matches Polaris part numbers 3514635 and 3585502 exactly — no modifications needed. Compatibility Make Model Engine Years Polaris Ranger 400 400cc 2010-2014 Polaris Ranger 500 500cc 2005-2018 Polaris Ranger 700 700cc 2005-2010 Polaris Ranger 800 800cc 2010-2014 Polaris Ranger 900 900cc 2013-2019 Polaris Worker 500 4x4 500cc Various Frequently Asked Questions Q: How do I know if my wheel bearings need replacement?A: Common symptoms: grinding or humming noise from the wheel area that changes with speed, excessive wheel play when you rock the tire side-to-side, uneven tire wear, or the wheel feeling "loose" during turns. To test: jack up the ATV, grab the tire at 12 and 6 o'clock, and rock it — any play indicates worn bearings. Q: Can I replace just one side?A: We recommend replacing both sides at the same time. Bearings wear at similar rates, and if one side is gone, the other is usually not far behind. This kit includes components for both sides. Q: What tools do I need for this job?A: You'll need a bearing press or a bearing driver kit, snap ring pliers, socket set, torque wrench, and a dead blow hammer. A hydraulic press makes the job straightforward. Without one, you can use the freezer/heat method (freeze bearings, heat hub with a heat gun), but a press is strongly recommended.Related Guides & Articles📖 ATV Wheel Bearing Replacement: Step-by-Step DIY Guide
$53.99
iFJF 35610 Metal Hook Hanger Replacement for Hose and Outdoor Decorative Suspension — Heavy Duty
Overview The iFJF 35610 Metal Hook Hanger is a heavy-duty utility hook designed for reliable outdoor and indoor suspension applications. Whether you need to organize garden hoses, hang outdoor decorations, suspend tools in the garage, or create an organized storage solution in your shed or workshop, this versatile metal hook delivers the strength and durability you need. Constructed from heavy-gauge steel with a corrosion-resistant finish, the 35610 hook withstands outdoor exposure, workshop abuse, and the weight of heavy items without bending or breaking. The universal mounting design fits most standard wall surfaces with appropriate hardware (mounting screws sold separately based on your wall material). Key Features Heavy-Duty Steel Construction — Built from thick-gauge steel for dependable load-bearing capacity without bending under weight Corrosion-Resistant Finish — Protective coating resists rust and oxidation for reliable outdoor and damp-environment use Versatile Applications — Ideal for garden hoses, outdoor decorations, garage tool storage, extension cords, ladders, and more Universal Mounting — Pre-drilled mounting holes accept standard screws or bolts for secure attachment to wood, drywall (with anchors), or concrete (with appropriate fasteners) Curved Hook Design — Wide opening and deep curve securely hold items without slipping off, even in windy outdoor conditions Multi-Pack Flexibility — Use individually for focused storage or combine multiple hooks for organized wall storage systems Technical Specifications Specification Details Part Number 35610 Material Heavy-Gauge Steel with Corrosion-Resistant Finish Application Indoor/Outdoor Suspension, Hose Storage, Utility Hanging Mounting Pre-Drilled Holes — Screws Sold Separately Finish Corrosion-Resistant Coating Recommended Uses Garden hose storage and organization Outdoor decorative item suspension (wind chimes, planters, bird feeders) Garage tool and extension cord hanging Workshop and shed organization RV and camper exterior accessory mounting Bicycle, ladder, and bulky item wall storage FAQ Q: What is the weight capacity of this hook?A: When properly mounted into a stud or solid backing, this heavy-gauge steel hook can support approximately 25-40 lbs (11-18 kg). For drywall installations, always use appropriate wall anchors rated for your intended load. The limiting factor is usually the mounting surface and hardware, not the hook itself. Q: Are mounting screws included?A: Mounting screws are not included, as the appropriate fastener depends on your mounting surface — wood screws for studs, toggle bolts or anchors for drywall, concrete anchors for masonry, etc. The pre-drilled holes accommodate standard #8 or #10 screws. Q: Can this be used outdoors in all weather conditions?A: Yes. The corrosion-resistant finish is designed for outdoor exposure to rain, humidity, and temperature fluctuations. For coastal or extreme environments, periodic inspection and touch-up of the finish is recommended to maintain appearance and rust resistance. Q: Will this hold a heavy, water-filled garden hose?A: Yes. A standard 50-foot garden hose (approximately 8-10 lbs dry, slightly more when water remains in the hose) is well within the hook's capacity. Ensure the hook is mounted into a stud or solid wood backing for the most secure installation. Q: How deep is the hook opening?A: The hook features a generous deep curve design that securely cradles items. The exact dimensions vary by production batch — refer to the product photos for scale reference. The opening accommodates standard garden hoses, extension cords, and most tool handles comfortably. Q: Can I use this indoors as a coat or bag hook?A: Absolutely. While designed for utility use, the clean metal finish works well for indoor coat hooks, bag hooks, mudroom organization, or decorative hanging applications. The heavy-duty construction easily handles coats, backpacks, and bags. Q: Is this sold individually or in a multi-pack?A: This listing is for one individual hook. For organizing multiple hoses, tools, or creating a wall storage system, order the quantity needed. Many customers purchase 3-6 hooks for a complete garage or shed organization project. Q: How does the finish hold up to UV exposure?A: The corrosion-resistant coating provides good UV protection for outdoor use. Over extended years of direct sunlight, some fading of the finish is normal but does not affect structural integrity. For longest finish life in sunny climates, occasional application of a clear protective spray coating can help. 📚 Related Guides & Articles iFJF Guides & Resources — Expert Tips, Installation Tutorials & Buying Guides
$49.99
iFJF 35mm Rear Wheel Bearing Greaser Tool for Polaris RZR Ranger Sportsman General
Product Overview Service your Polaris 35mm rear wheel bearings the professional way — without removing the hub assembly. This purpose-built bearing greaser tool injects fresh grease directly into the bearing cavity through a standard zerk fitting, pushing old, contaminated grease out the opposite side in a complete flush. Designed for Polaris RZR, Ranger, Sportsman, and General models with 35mm rear bearings. A single bearing replacement costs $80-150 in parts plus 2-3 hours of labor. This tool pays for itself the first time you use it. Key Features 35mm Precision Fit — CNC-machined for an exact, leak-free seal on Polaris 35mm rear wheel bearing hubs. Won't slip or spray grease during the injection process. No Hub Removal Required — Jack up, remove the wheel and axle nut, slide the greaser over the bearing hub, and pump. No hub disassembly, no press work, no bearing removal. Complete service in 5-10 minutes per side. Complete Grease Flush — The tool forces fresh grease through the bearing from one side while pushing old, contaminated grease (with water, mud, and metal particles) out the other side. True flush, not just a top-off. CNC-Machined 6061-T6 Aluminum — Anodized for corrosion resistance and built to withstand repeated shop use. Includes O-ring seals and a standard grease gun zerk fitting. Broad Polaris Compatibility — Fits all Polaris models using 35mm rear wheel bearings: RZR 800/900/1000/XP/Turbo/Pro (2008+), Ranger 500-1000 (2013+), Sportsman 500-1000 (2009+), General 1000 (2016+). Compatibility / Fitment Brand Model Series Years Bearing Size Polaris RZR 800 / 900 / 1000 / XP / Turbo / Pro 2008-Present 35mm ID Polaris Ranger 500 / 570 / 700 / 800 / 900 / 1000 / XP 2013-Present 35mm ID Polaris Sportsman 500 / 570 / 700 / 850 / 1000 2009-Present 35mm ID Polaris General 1000 / XP 2016-Present 35mm ID Technical Specifications Specification Value Bearing Size Compatibility 35mm Inner Diameter Material 6061-T6 Aluminum (Anodized) Grease Fitting Standard Zerk (1/8" NPT) Kit Contents Greaser Body, O-Ring Seals, Zerk Fitting, Instructions Service Time Per Side 5-10 Minutes Why Choose This Polaris rear wheel bearings are exposed to water, mud, sand, and extreme loads — and they're not cheap to replace. A single OEM bearing assembly costs $80-150, and installation requires a hydraulic press and 2-3 hours of labor. Regular greasing with this tool flushes out contaminants before they cause pitting and failure, easily doubling bearing service life. At $40, it pays for itself on the first bearing you save. Trail riders especially benefit — a quick grease job before a multi-day ride prevents the dreaded "bearing howl" 50 miles from the truck. Related Products More in Ford F-Series & Powerstroke: 6PK2060 Part 6PK2120 Part V10 Part Browse all Polaris Parts — Tools and accessories for Polaris ATV/UTV Shop All iFJF Parts — Complete product catalog Frequently Asked Questions Q: Will this work on my Polaris RZR 1000 XP?A: Yes. The RZR 1000 XP and all RZR 1000 variants (including Turbo and Pro XP) use 35mm rear wheel bearings. This greaser fits all RZR 1000 models from 2014 to present. Q: How often should I grease my rear wheel bearings?A: Every 500 miles under normal riding conditions. After any significant water crossing or mud riding. Before and after multi-day trail rides. More frequent greasing = longer bearing life — grease is cheap, bearings are not. Q: Does this work on front wheel bearings too?A: No — this is specifically designed for 35mm rear wheel bearings. Front hubs on Polaris models use different bearing sizes and configurations that require a different greaser tool. Q: Can I over-grease and damage the bearing seals?A: No — the tool design allows excess grease to exit the opposite side of the bearing, flushing old grease out rather than building pressure. The bearing seals are designed to allow this controlled grease exit path. Q: What type of grease should I use?A: Use a high-quality NLGI #2 lithium-complex or synthetic grease rated for wheel bearings. Marine-grade grease is recommended if you frequently ride through water or in wet conditions. Avoid mixing grease types — if unsure, flush completely and start fresh. Q: How do I know if my bearings are already too far gone?A: If you hear grinding, feel roughness when rotating the hub by hand, or see rust-colored grease leaking from the seal, the bearing is already damaged. Greasing can't reverse existing pitting or spalling — but it can prevent it in healthy bearings. Order with Confidence Fast shipping from our US warehouse. Dedicated customer support team ready to answer your questions. Click Add to Cart to get your order started today. Related Guides & Articles Check out these helpful resources from the iFJF blog: Golf Cart Bearing — Club Car Wheel Hub Bearing Replacement DIY Guide
$39.99
iFJF 36 Sq.ft Pool Filter Grille Assembly 59023500 | Replaces DEX3620DC DEX3600DA | iFJF
Product Overview 36 Sq.ft Pool Filter Grille Assembly 59023500 | Replaces DEX3620DC DEX3600DA | is a premium-quality replacement component engineered for exact fitment and reliable performance. Manufactured to meet or exceed OEM specifications using high-grade materials, this part delivers dependable service life for your equipment. Key Features Precision Fit: Engineered to exact OEM dimensions for leak-free, drop-in installation. Chemical Resistant: Made from high-grade materials that resist chlorine, bromine, and ozone degradation. Direct Replacement: No modifications required — simply remove the old part and install this one. Durable Construction: Premium materials prevent cracking, warping, and compression set over time. Cost-Effective: Get OEM-equivalent quality at a fraction of dealer pricing. Specifications Specification Detail Brand iFJF Product Type Pool Filter Condition New Replaces Part # 59023500 Warranty 12 Months Why Choose iFJF Direct iFJF Direct specializes in premium replacement parts for diesel trucks, RVs, marine, pool & spa, and automotive applications. Every product is backed by our commitment to quality, fast US-based shipping, and responsive customer support. We source directly from IATF 16949-certified manufacturers to bring you OEM-equivalent quality at competitive prices. Frequently Asked Questions Q: Will this fit my pool/spa model?A: Please verify your multiport valve model number against the specifications listed. This part is designed for HiFlow-compatible valves. Contact us with your valve model if you need help confirming fitment. Q: What material is this made from?A: This component is manufactured from high-grade, chemical-resistant materials engineered to withstand constant exposure to chlorine, bromine, and ozone in pool and spa environments. Q: How do I install this part?A: Installation is straightforward — remove the old component and replace with this direct-fit part. We recommend using silicone-based lubricant on gaskets and O-rings during installation for optimal sealing. Q: How long will this last?A: With proper maintenance and balanced water chemistry, these components typically provide 3-5 years of reliable service. Inspect annually for signs of wear. Q: Is this an OEM part?A: This is a premium aftermarket replacement manufactured to match OEM specifications. It provides equivalent performance at a more affordable price point.
$383.00
iFJF 385230325 Vacuum Breaker Kit for Sealand Traveler Toilets — Hand Sprayer
385230325 RV Toilet Vacuum Breaker Kit — Hand Sprayer — Stop Leaks & Prevent Backflow A leaking vacuum breaker on your RV toilet doesn't just waste water — it can siphon contaminated water back into your fresh water system, cause odors, and damage your bathroom floor. The iFJF 385230325 Vacuum Breaker Kit is the correct dual-port replacement for Dometic/Sealand Traveler and VacuFlush toilets equipped with a hand sprayer. Unlike single-port alternatives, this kit includes the dedicated sprayer connection port — no adapters, no leaks, no compromises. Complete kit includes vacuum breaker body, integrated dual-seal check valve, all O-rings and gaskets, and stainless steel mounting hardware. Measures 3.25" L × 1.73" W × 3.65" H for exact drop-in fit. Key Features Hand Sprayer Compatible: Dual-port design with dedicated sprayer connection — no T-fittings or adapters that create leak points. Specifically for toilets WITH a hand sprayer. Complete Kit: Vacuum breaker body (3.25"L × 1.73"W × 3.65"H), dual-seal check valve, all O-rings, gaskets, and stainless steel hardware — everything needed. Backflow Prevention: Dual-seal check valve prevents contaminated water from siphoning back into your fresh water plumbing. Meets ABYC and RVIA code requirements. Durable Materials: High-impact ABS body withstands years of vibration from road travel. Nitrile seals resist holding tank chemicals and marine sanitation products. DIY-Friendly: 20-30 minute installation with basic hand tools. 1/2" NPT connections match factory plumbing. Compatibility Brand Series Models / Notes Dometic / Sealand Traveler 110, 111, 210, 211, 510, 511 (with hand sprayer) Dometic / Sealand VacuFlush All models with hand sprayer attachment ⚠️ Not Sure Which Kit? If there's a coiled hose behind your toilet connected to the breaker → this is your kit. No hose → order 385316906 (no sprayer). Specifications Specification Detail Part Number 385230325 Dimensions 3.25"L × 1.73"W × 3.65"H Material ABS Body / Nitrile Seals / Stainless Steel Hardware Connection 1/2" NPT — Dual Port (Water Inlet + Sprayer) Check Valve Dual-Seal, Integrated Symptoms of a Failed Vacuum Breaker Water leaking or spraying from behind the toilet pedestal — especially when the hand sprayer is used Continuous slow drip from the breaker housing Bowl fails to hold water after flushing Sewage odor near the toilet (backflow through failed check valve) Reduced sprayer pressure or water hammer when flushing Installation Steps Shut off water supply to the toilet. Flush to relieve system pressure. Disconnect the hand sprayer hose and water supply line from the old breaker. Remove the old vacuum breaker (typically 2 screws or threaded collar). Clean mounting surface and inspect for cracks or damage. Install new breaker with supplied gaskets — 2-3 wraps of Teflon tape on threaded connections. Reconnect sprayer hose and water line, turn on supply, test all connections for leaks. Why Choose iFJF? iFJF vacuum breaker kits are manufactured to OEM Dometic/Sealand specifications with upgraded nitrile seals for extended service life — especially important in hot climates where rubber seals degrade faster. US-based support and fast shipping from our American warehouse. Related Products Frequently Asked Questions Q: Does this fit toilets without a hand sprayer?A: No. If your Sealand/Dometic toilet does NOT have a hand sprayer, you need the 385316906 (single-port) vacuum breaker kit. This 385230325 has a dedicated sprayer port. Q: How long does installation take?A: 20-30 minutes. Accessing the back of the toilet in tight RV bathrooms is typically the most time-consuming part. A compact mirror and headlamp make it easier. Q: Do I need thread sealant or Teflon tape?A: Yes. Apply 2-3 wraps of Teflon tape to male threaded connections. Do not use pipe dope or liquid sealants — they can degrade the nitrile seals. Q: Why does my breaker leak only when I use the hand sprayer?A: This is a classic sign of a failed check valve inside the vacuum breaker. The sprayer back-pressures the system, and a worn seal can't hold. Replacement is the fix. Q: Will this stop sewage odors?A: If the odor is from backflow through a failed vacuum breaker — yes. If caused by a failed floor flange seal or holding tank vent, those may need separate repair. 📚 Related Guides & Articles Complete Onan Quiet Diesel RV Generator Tune-Up Why You Need a Bluetooth Kill Switch for Your RV or Truck
$27.99
iFJF 385310076 Duckbill Valve for Sealand S&T Vacuum Pumps — Single Replacement
385310076 Duckbill Valve — Single Replacement for Sealand Vacuum Pumps When your Sealand VacuFlush toilet loses vacuum or cycles constantly, the culprit is almost always a worn duckbill valve. This iFJF 385310076 single replacement duckbill valve is manufactured from premium nitrile rubber and sized for all Sealand S-Series and T-Series vacuum generator pumps. Ideal for boat and RV owners who need to replace one failed valve or build a spare parts kit — without buying a full rebuild kit. Key Features Premium Nitrile Rubber: Withstands chemical exposure from holding tank treatments and mineral buildup — outlasts generic silicone valves. Single Valve Purchase: Buy exactly what you need. No waste, no unused parts. OEM-Spec Dimensions: Precise lip geometry ensures complete one-way seal. Drops into S12D, S24D, S32D, T12, T24, T32 without modification. Silicone Grease Included: Pre-lubricated for easy installation without tearing. Universal S-Series/T-Series Fit: Compatible with all Sealand vacuum generator pumps. Compatibility Series Models S-Series S12D, S24D, S32D, S115A, S12, 52A, S32 T-Series T12, T24, T32 VHT/VG VHT12, VHT24, VG4, VG5 Specifications Spec Value Part Number 385310076 Material Premium Nitrile Rubber Valve Type One-Way Duckbill Check Valve Quantity 1 (Single Pack) Includes Valve + Silicone Grease Packet When to Buy a Single Valve vs. 2-Pack Buy Single: Inlet valve failed but outlet still good. Building a spare parts kit for cruising or camping. Troubleshooting to isolate which valve is the problem. Buy 2-Pack: Both valves are original and over 2 years old. Complete pump rebuild recommended. Pump cycles every few minutes. Symptoms of Failed Duckbill Valves Pump runs continuously without building pressure Weak or incomplete flushes Pump cycles every few minutes without flushing Foul odor from vacuum tank area Hissing sound near pump during operation Installation Tips Turn off power at breaker. Open pump housing (4-6 screws). Note orientation: tapered beak must face toward holding tank. Remove old valve carefully. Clean mounting surfaces thoroughly. Apply included silicone grease to valve lip and press into place. Reassemble housing, restore power, test with 3-4 flushes. Check for vacuum hold — pump should not cycle within 2 minutes of idle. Frequently Asked Questions Q: How do I identify which valve is bad?A: Listen near each valve while pump runs. Hissing = leak at that valve. Vacuum bleeds immediately after pump stops = inlet valve failure. Pump slow to build vacuum but holds once achieved = outlet valve issue. Q: Should I buy one valve or the 2-pack?A: If both valves are original and over 2 years old, buy the 2-pack for a complete rebuild. If one failed prematurely (chemical damage, debris), a single replacement is sufficient. Q: How often should duckbill valves be replaced?A: Every 2-3 years under normal use. Liveaboards and full-time RVers should replace annually. Holding tank chemicals accelerate rubber degradation — inspect valves during annual maintenance. Q: Will non-OEM valves work as well as original?A: Our premium nitrile valves match OEM specifications and dimensions. Many marine mechanics report our nitrile compound outlasts OEM rubber in chemically-treated systems. Q: Can I install this myself?A: Absolutely. The job takes 15-20 minutes with basic hand tools (screwdriver). No specialized marine or RV knowledge required. Watch our installation video for step-by-step guidance. Q: What happens if I install it backward?A: The pump won't build vacuum because the valve will be forced open instead of sealed. The tapered beak MUST face toward the holding tank (away from the vacuum pump). If installed backward, simply flip it around. Related Products 📚 Related Guides & Articles Complete Onan Quiet Diesel RV Generator Tune-Up Marine Fuel Water Separator Guide: Why Your Outboard Needs One
$19.99
iFJF 385310076 Duckbill Valve Kit for Sealand S&T Vacuum Pumps — 2-Pack Complete Rebuild
385310076 Duckbill Valve Kit — Complete Sealand Vacuum Generator Rebuild (2-Pack) When your Sealand VacuFlush toilet loses vacuum or cycles constantly, worn duckbill valves are almost always the cause. These one-way rubber check valves degrade from waste chemicals and mineral buildup. The iFJF 385310076 Duckbill Valve Kit includes two premium nitrile valves sized for all Sealand S-Series and T-Series vacuum generators. Rebuild your pump in under 30 minutes and restore factory vacuum performance. Key Features Complete 2-Pack Value: Both inlet and outlet valves needed for a proper pump rebuild. Replace both while you have the housing open. Premium Nitrile Rubber: Resists chemical attack from holding tank treatments — outlasts generic silicone valves by 2-3x in chemical-rich environments. Universal S&T Fit: Compatible with S12D, S24D, S32D, T12, T24, T32, and VHT/VG series vacuum generators. OEM-Dimension Match: Precise lip geometry ensures complete one-way seal — no vacuum loss between flushes. Includes Silicone Grease: Pre-applied lubrication prevents tearing during installation and ensures a perfect seal. Compatibility Pump Series Models S-Series S12D, S12DAB, S24D, S32D, S115A, S12, 52A, S32 T-Series T12, T24, T32 VHT/VG VHT12, VHT24, VG4, VG5 Specifications Spec Value Part Number 385310076 Material Premium Nitrile Rubber Valve Type One-Way Duckbill Check Valve Quantity 2 (Inlet + Outlet) Includes 2x Valves + Silicone Grease Packet Symptoms of Failed Duckbill Valves Pump runs continuously without building pressure Weak or incomplete flushes — bowl doesn't clear completely Pump cycles every few minutes without anyone flushing Foul odor from vacuum tank area Hissing sound near pump housing during operation Vacuum gauge shows pressure bleed-down Installation Guide Turn off power at breaker. Locate vacuum generator pump. Remove pump housing cover (4-6 screws depending on model). Note orientation: tapered beak faces toward holding tank on both valves. Remove old valves carefully — they may be brittle. Clean mounting surfaces with a rag. Apply included silicone grease to the lip of each new valve. Press new valves firmly into their seats. Ensure full perimeter contact. Reassemble housing, tighten screws evenly. Restore power. Test with 3-4 flushes. Verify pump shuts off and vacuum holds for 2+ minutes. Frequently Asked Questions Q: How do I know which valve is bad — inlet or outlet?A: Listen near each valve while pump runs — hissing indicates a leak at that valve. Vacuum bleeding immediately after pump stops suggests inlet valve failure. Slow to build vacuum but holds once achieved points to outlet valve wear. When in doubt, replacing both is recommended. Q: How often should duckbill valves be replaced?A: Replace every 2-3 years under normal recreational use. Liveaboards and full-time RVers should replace annually. If you use formaldehyde-based holding tank chemicals, inspect every 6 months — chemicals accelerate rubber degradation significantly. Q: Why buy the 2-pack instead of single valves?A: Both valves wear at similar rates. If one has failed, the other is likely close behind. Replacing both saves you from opening the pump housing again in a few months — and costs less than two single purchases. Q: Will these fit my older Sealand pump?A: Yes. The 385310076 duckbill valve fits all S-Series and T-Series Sealand/Dometic vacuum generators dating back to the 1990s. The design has not changed. Q: Can I do this repair myself?A: Absolutely. This is a 20-30 minute DIY job requiring only a screwdriver. No plumbing or electrical expertise needed. We include step-by-step instructions in every kit. Q: What happens if I install a valve backward?A: The pump will run continuously but never build vacuum — the valve will be forced open instead of sealing. The tapered beak MUST face toward the holding tank. If you make this mistake, simply open the housing and flip the valve around. Related Products 📚 Related Guides & Articles Complete Onan Quiet Diesel RV Generator Tune-Up Marine Fuel Water Separator Guide: Why Your Outboard Needs One 📖 Related Guide: VacuFlush Toilet Seal Replacement: Step-by-Step Install Guide →
$25.99
iFJF 385310681 Flush Ball & Shaft Cartridge Kit for Sealand Dometic VacuFlush Toilets
385310681 Flush Ball & Shaft Cartridge Kit — Complete Sealand Toilet Rebuild A sticky, hard-to-flush, or leaking toilet bowl can ruin any boating trip or RV vacation. The iFJF 385310681 kit replaces the entire flush mechanism in Dometic Sealand Traveler and VacuFlush foot-pedal toilets with plastic pedals. This complete cartridge assembly includes a Teflon-coated flush ball, stainless steel shaft, dual lip seals, O-rings, and mounting clip — everything needed for a smooth, odor-free flush restoration. Key Features Complete Cartridge Assembly: Includes flush ball, stainless steel shaft, dual lip seals, O-rings, and retaining clip — no need to piece together individual parts from multiple sources. Teflon-Coated Flush Ball: Ultra-smooth Teflon surface ensures effortless flush action with minimal foot pressure — no more sticky, hard-to-press pedals. Designed for Plastic-Pedal Toilets: Specifically engineered for Dometic/Sealand foot-pedal toilets with plastic pedal arms (not metal). Verify your pedal type before ordering. Odor-Tight Dual Lip Seals: New high-performance lip seals create a positive barrier that prevents holding tank odors from entering the bathroom. Stainless Steel Shaft: Corrosion-resistant shaft won't rust or seize — ensures years of smooth operation in the humid marine/RV bathroom environment. Compatibility Brand Series Pedal Type Models Dometic / Sealand Traveler Foot Pedal (Plastic) 110, 111, 210, 211, 510, 511 Dometic / Sealand VacuFlush Foot Pedal (Plastic) 147, 148 Specifications Spec Value Part Number 385310681 Ball Material Polymer Core with Teflon Coating Shaft Material Stainless Steel Seal Type Dual Lip — Odor-Tight Design Kit Contents Flush Ball, Shaft, Lip Seals, O-Rings, Retaining Clip Symptoms You Need This Kit Foot pedal is stiff or requires excessive force to flush Flush ball sticks in the open position (allowing odors to escape) Bowl loses water between uses — slow drain into holding tank Loose, wobbly, or rattling foot pedal Flush ball doesn't return to closed position after releasing pedal Water visible around the flush ball seal when bowl is filled Installation Guide Turn off water supply to toilet. Disconnect water line. Remove toilet from floor flange (typically 2 bolts through the base). Access the cartridge assembly from the bottom of the toilet bowl. Remove the retaining clip securing the old cartridge. Slide the old cartridge out of the bore. Thoroughly clean the cartridge bore — remove all old grease, mineral deposits, and debris. Apply a thin coat of silicone grease (included) to the new lip seals. Slide the new 385310681 cartridge into the bore. Ensure proper orientation and alignment. Secure with the new retaining clip. Reinstall toilet onto floor flange. Reconnect water, turn on supply, and test flush operation with 5-6 cycles. Frequently Asked Questions Q: Does this fit metal pedal or plastic pedal toilets?A: This kit is specifically designed for plastic-pedal Dometic/Sealand toilets. Verify your pedal material before ordering — metal-pedal toilets use a different cartridge assembly. Q: How long does this cartridge typically last?A: With normal use, expect 5-7 years of service life. Avoid abrasive bowl cleaners (Comet, Ajax) which can scratch the Teflon coating and accelerate seal wear. Use liquid toilet bowl cleaners instead. Q: Is this a DIY job or do I need a professional?A: This is a moderately involved DIY project — expect 45-90 minutes for your first time. The toilet must be removed from the floor flange to access the cartridge. Having a second person to help lift the toilet makes the job much easier. Q: What's the most common installation mistake?A: Not cleaning the cartridge bore thoroughly enough. Old grease and mineral deposits can prevent the new seals from seating properly, causing immediate leaks. Take the extra 5 minutes to clean the bore completely. Q: My flush ball sticks — do I need the whole kit or just lubrication?A: If lubrication temporarily fixes the sticking, you may only need to clean and re-grease the existing assembly. If the problem returns quickly or the Teflon coating is visibly worn/scratched, replace the entire cartridge. Q: Will this stop holding tank odors in my bathroom?A: Yes, if the odor is entering through the toilet bowl. The dual lip seals in this kit create an airtight barrier between the bowl and holding tank. Combine with a properly functioning vent system for complete odor elimination. Related Products Pairs with this part: Flush Ball Shaft RV Part Related Products Water Valve Kit for Sealand 300/310/320 RV Toilets — 385311641 13168 RV Toilet Water Valve Kit for Aqua Magic IV Toilets 34117 Waste Ball Valve Seal Kit for Aqua Magic Style II RV Toilet Related Guides & Articles Complete Onan Quiet Diesel RV Generator Tune-Up Best Water Separator Fuel Filter for Diesel & Marine Engines Diesel Fuel Filter Replacement: The Complete Guide 📖 Related Guide: VacuFlush Toilet Seal Replacement: Step-by-Step Install Guide →
$34.99
iFJF 385311462 RV Toilet Bowl Seal Kit for Dometic & Vac-UFlush Toilets
Overview The iFJF 385311462 RV Toilet Rubber Bowl Leak Seal Kit is the permanent fix for that annoying toilet bowl leak that wastes water and creates unpleasant odors in your RV. If your toilet bowl won't hold water between flushes or you smell sewer gas seeping through, this seal kit replaces both the rubber bowl seal and flush ball seal — restoring a watertight barrier without expensive shop visits. Compatible with most popular Dometic/SeaLand pedal-flush and Vac-UFlush toilet models (see compatibility chart below). Built from high-quality sealing rubber that matches or exceeds OEM material specs. No special tools required — most RV owners complete the swap in under 15 minutes. Key Features Dual-Seal Design — Includes both rubber bowl seal (7" x 2" x 1/16") and flush ball seal (7" x 1-5/8" x 1/4") for a complete leak solution in one kit. Watertight Shutoff — Precision-molded rubber creates a tight seal against the water outlet pipe, stopping the slow drain-down that wastes fresh water between flushes. Odor Elimination — Blocks sewer gas from entering the RV interior through a leaking toilet seal. 15-Minute DIY Install — Simple plug-and-play replacement with no special tools or plumbing skills required. Saves $100+ in dealer labor fees. OEM-Spec Rubber — Manufactured from durable, flexible rubber compound that resists cracking, hardening, and chemical breakdown from RV holding tank treatments. Compatibility / Fitment Toilet Series Compatible Models Pedal Flush (Dometic/SeaLand) 506+, 511H, 547+, 548+, 706, 709, 748, 749, 806, 808, 847, 848, 1147, 1148, 2010, 2011, 5006, 5047, 5048, 5049 Vac-UFlush (Dometic/SeaLand) 168, 606, 647, 648, 1006, 1008, 1047, 1048, 1049, 1106, 5146, 5148, 5149 Replaces OEM Part # 385311462, 385310677 — direct replacement NOT compatible with Dometic 300, 310, 320 series toilets or Thetford cassette toilets. Specifications Specification Details Bowl Seal Dimensions 7" diameter x 2" wide x 1/16" thick Ball Seal Dimensions 7" diameter x 1-5/8" wide x 1/4" thick Material High-quality sealing rubber Package Includes 1x Rubber Bowl Seal, 1x Rubber Flush Ball Seal OEM Part Numbers 385311462, 385310677 Why Choose iFJF Every RV owner knows a leaking toilet means wasted fresh water on the road and an unpleasant living space. Dealership replacement charges can run $150-250 — this seal kit gives you OEM-quality parts at a fraction of the cost, with a straightforward install you can complete at the campsite. Frequently Asked Questions Q: How do I know if my toilet bowl seal is leaking?A: The #1 symptom is the toilet bowl losing water between flushes. If you fill the bowl, walk away, and come back to find it nearly empty, the bowl seal is failing. You may also notice a faint sewer odor around the toilet area. Q: Will this fit my Dometic 310 toilet?A: No. This seal kit is NOT compatible with Dometic 300, 310, or 320 series toilets. It is designed for the older pedal-flush model numbers listed in the compatibility chart. Check the model number sticker inside your toilet before ordering. Q: How long does installation take?A: Most RV owners complete the swap in 15 minutes with basic hand tools (screwdriver and wrench). No plumbing skills needed. Q: Does this kit include both seals I need?A: Yes. The package includes one rubber bowl seal and one rubber flush ball seal. Replacing both at once ensures a complete, long-lasting fix. Q: What's your warranty?A: All iFJF products come with a 12-month warranty against manufacturing defects. Contact us for a free replacement or full refund. Stop that toilet leak today — ships from iFJF warehouse within 1 business day. Product Overview 385311462 RV Toilet Bowl Seal Kit for Dometic & Vac-UFlush Toilets is a premium-quality replacement component engineered for exact fitment and reliable performance. Manufactured to meet or exceed OEM specifications using high-grade materials, this part delivers dependable service life for your equipment.
$23.99
iFJF 385311462 VacuFlush Toilet Seal Kit for Dometic Sealand 110 111 210 510 — Teflon
Product Overview Stop bowl water loss and sewer odors with this upgraded Teflon-faced toilet seal kit for Dometic Sealand VacuFlush toilets. Designed for models 110, 111, 210, and 510 — common in higher-end RVs, boats, and marine applications — this kit replaces both the 385311462 and 385310677 seal assemblies. The Teflon-faced polymer disk with raised alignment groove outperforms standard rubber seals, maintaining its shape through thousands of flush cycles and creating an odor-tight seal that lasts significantly longer. Key Features Upgraded Teflon-Faced Disk — Unlike standard rubber seals that develop compression set (permanent flattening), the Teflon surface resists deformation through thousands of flush cycles, maintaining a consistent seal. Raised Alignment Groove — Precision-molded groove centers the seal on the VacuFlush ball valve for even wear distribution and consistent sealing pressure around the entire circumference. Complete Seal Kit — Includes Teflon-faced seal disk, mounting ring, O-rings, and silicone lubricant packet — no additional parts needed for a complete rebuild. Direct OEM Replacement — Exact replacement for Dometic/Sealand part numbers 385311462 and 385310677. Same dimensions, same fit, upgraded material. Marine & RV Compatible — Works in both recreational vehicle and marine (boat/yacht) installations with VacuFlush toilet systems. Compatibility / Fitment Brand Series Models Replaces Part # Dometic / Sealand VacuFlush 110, 111, 210, 510 385311462, 385310677 Technical Specifications Specification Value Part Numbers 385311462, 385310677 Seal Material Teflon-Faced Polymer Disk Kit Contents Seal Disk, Mounting Ring, O-Rings, Silicone Lube Compatible Flush Type VacuFlush (Vacuum Flush) Installation Time 30-45 Minutes Why Choose This VacuFlush toilets are premium systems — and their seals demand premium materials. Standard rubber seals on these toilets often fail within 1-2 years, letting bowl water drain into the holding tank (creating sewer gas path) and allowing odors to enter the living space. The Teflon-faced design in this kit addresses both failure modes: it maintains its shape (no compression set) and creates a superior gas-tight barrier. Marine boat owners especially benefit, as salt air accelerates rubber degradation significantly. Related Products More in Plumbing & Bath: 13168 RV Part Browse all RV Plumbing Parts — Complete selection of seals and repair components Shop All iFJF Parts — Our full product catalog Frequently Asked Questions Q: Will this fit my VacuFlush 510 Plus series?A: Yes. The 510 series (including 510 Plus) uses this exact seal kit. The seal interface is common across all 110, 111, 210, and 510 VacuFlush toilet models from Dometic/Sealand. Q: How is Teflon better than the standard rubber seal?A: Teflon-faced seals resist compression set — the permanent flattening that causes rubber seals to lose their shape. This means a consistent seal over many more flush cycles. Teflon also has a lower coefficient of friction, reducing wear on the flush ball surface. Q: Why is my toilet bowl water dropping within hours?A: When the VacuFlush seal fails, water slowly drains from the bowl into the holding tank. This also creates an open path for sewer gases to enter the bathroom. Replace the seal to fix both issues simultaneously. Q: How often should I replace the VacuFlush seals?A: Under normal RV use, every 2-3 years. In marine (saltwater) environments or full-time liveaboard use, every 1-2 years. Replace sooner if you notice the bowl losing water or detect sewer odors. Q: Does this kit include the silicone lubricant?A: Yes. A packet of silicone lubricant is included. Apply lightly to the Teflon seal surface during installation — this helps the seal bed in and ensures smooth flush ball operation from day one. Q: Can I install this myself or do I need a tech?A: DIY-friendly with basic mechanical skills. Budget 30-45 minutes. Key steps: shut off water, flush to empty bowl, remove toilet from flange, replace seal components, reassemble, test with 4-5 flushes. Order with Confidence Fast shipping from our US warehouse. Dedicated customer support team ready to answer your questions. Click Add to Cart to get your order started today. Related Guides & Articles Check out these helpful resources from the iFJF blog: RV Maintenance — Complete Diesel Truck & RV Maintenance Schedule 2026 RV Generator Guide — Cummins Onan RV Generator Maintenance Guide 2026 Related Guide Read: RV VacuFlush Toilet Bowl Seal Replacement: Fix That Leak and Stop the Constant Pump Cycling 📖 Related Guide: VacuFlush Toilet Seal Replacement: Step-by-Step Install Guide →
$25.99
iFJF 385311653 RV Toilet Seal Kit for Dometic 300 310 320 — Includes 385311652 Hardware
Product Overview Fix your leaking, wobbling RV toilet in one repair with this complete seal kit for Dometic 300, 310, and 320 series gravity-flush toilets — the most popular RV toilet lineup in North America. This kit includes the 385311653 closed-cell foam floor seal to stop water and odor leaks at the base AND the 385311652 stainless steel mounting hardware kit (bolts, washers, nuts) to eliminate toilet wobble caused by corroded or stripped fasteners. One kit, one repair, problem solved. Key Features Complete Seal + Hardware Kit — Includes both the 385311653 closed-cell foam floor seal AND the 385311652 stainless steel bolt kit — everything you need for a complete toilet base repair. Closed-Cell Foam Construction — Unlike open-cell foam that acts like a sponge, closed-cell foam creates a true water barrier that won't wick moisture or absorb odors over time. Stainless Steel Hardware — The 385311652 bolts, washers, and nuts are stainless steel — they won't rust or corrode in the humid RV bathroom environment, unlike the factory carbon steel fasteners. Perfect Fit for Dometic 300/310/320 — Precision-cut to match the Dometic gravity-flush toilet base flange exactly. Same seal interface on the standard 300, low-profile 310, and elongated 320 models. DIY-Friendly Installation — 30-45 minute job with basic hand tools. No special plumbing skills required. Full instructions included. Compatibility / Fitment Brand Series Type Common Models Dometic 300 Standard Height, Gravity Flush Dometic 300 Dometic 310 Low Profile, Gravity Flush Dometic 310 Dometic 320 Elongated Bowl, Gravity Flush Dometic 320 Technical Specifications Specification Value Seal Part Number 385311653 Hardware Part Number 385311652 Seal Material Closed-Cell Foam Hardware Material Stainless Steel Flush Type Gravity Flush Installation Time 30-45 Minutes Why Choose This RV dealers charge $150-250 for this simple repair. This kit gives you everything needed to do it yourself in under an hour. The factory carbon steel bolts on Dometic toilets are notorious for rusting solid in the humid bathroom environment — our stainless steel hardware eliminates this problem permanently. The closed-cell foam seal won't degrade or absorb moisture like cheap open-cell alternatives. If your toilet is leaking at the base, rocking when you sit, or emitting sewer odors, this kit is the definitive fix. Related Products More in Plumbing & Bath: 13168 RV Part Browse all RV Plumbing Parts — Seals, valves, and repair kits Shop All iFJF Parts — Complete inventory Frequently Asked Questions Q: Does this fit the Dometic 310 low-profile model?A: Yes. The 385311653 seal interface is identical across all three Dometic gravity-flush models — the standard-height 300, low-profile 310, and elongated 320. The bolt pattern and flange design are the same. Q: How do I remove rusted factory bolts?A: If the original carbon steel bolts are heavily rusted, spray them with penetrating oil (PB Blaster or WD-40) and let sit for 15 minutes. Use a 6-point socket (not 12-point) to avoid rounding. If the bolt head snaps, the toilet will lift off the broken stud — remove the remainder with vice grips from underneath. Q: How tight should I torque the new bolts?A: Hand-tighten until the toilet feels firmly seated, then turn an additional 1/4 turn with a wrench. DO NOT overtighten — excessive torque can crack the ceramic toilet base or deform the plastic flange. The foam seal does the sealing work, not bolt pressure. Q: What are the signs my toilet seal needs replacement?A: Watch for: water pooling around the toilet base after flushing, a persistent sewer odor near the toilet (even with the fan running), the toilet rocks or wobbles when you sit, visible water staining on the floor around the base, and corroded or stripped mounting bolts. Q: Can I reuse the old bolts if they look okay?A: We strongly recommend replacing the bolts with the new stainless steel hardware included in this kit. Factory bolts that look okay externally may be heavily corroded inside the flange — and carbon steel will eventually rust. Stainless hardware is a permanent upgrade. Q: Do I need to remove the toilet completely?A: Yes. The seal sits between the toilet base and the floor flange. You must lift the toilet off the floor to access and replace the old seal. Shut off the water supply, disconnect the water line, and remove the mounting bolts to lift the toilet. Order with Confidence Fast shipping from our US warehouse. Dedicated customer support team ready to answer your questions. Click Add to Cart to get your order started today. Related Guides & Articles Check out these helpful resources from the iFJF blog: RV Maintenance — Complete Diesel Truck & RV Maintenance Schedule 2026 RV Generator Guide — Cummins Onan RV Generator Maintenance Guide 2026
$25.99
iFJF 385311658 Flush Ball Ring Seal for Dometic 300/310/320 RV Toilet — Bowl Seal Kit
385311658 Flush Ball Ring Seal — Complete Dometic Bowl Seal Kit Slow bowl water loss or faint sewage odor in your RV bathroom almost always points to a worn flush ball seal ring. The iFJF 385311658 is an exact-replacement seal for the critical junction between the flush ball and toilet bowl in Dometic 300, 310, and 320 series gravity-flush toilets. Made from durable, chemical-resistant polymer, this seal restores the water-tight and odor-proof barrier in under 30 minutes — no tools required, installed entirely from above the bowl. Key Features Exact OEM Fit: Precision-molded to Dometic specifications for 300, 310, and 320 series toilets — drops into the seal groove without modification or trimming. Dual-Seal Function: Creates a positive water barrier to keep bowl water from draining into the holding tank AND an odor seal to prevent sewage gases from entering the bathroom. Chemical-Resistant Polymer: Engineered to withstand formaldehyde-based and enzyme-based holding tank treatments — won't swell, soften, or degrade. Tool-Free Installation: The only Dometic toilet repair that requires zero tools — accessed and replaced entirely from above the bowl in 20-30 minutes. Budget-Friendly Maintenance: The most affordable Dometic toilet seal on the market — replace prophylactically every 2 years for peace of mind. Compatibility Brand Series Toilet Type Dometic 300, 310, 320 Gravity-Flush (All Models) Specifications Spec Value Part Number 385311658 Material Chemical-Resistant Polymer Seal Type Flush Ball Ring / Bowl Seal Installation Tool-Free — Above Bowl Access Includes Seal Ring + Installation Grease Symptoms of a Failed Bowl Seal Bowl water drains completely within 1-2 hours of flushing Holding tank odor noticeable near toilet (especially on hot days) Mineral buildup or black residue visible around flush ball opening Toilet requires multiple flushes to clear waste (insufficient bowl water) Gurgling sounds from toilet when not in use Installation Guide (Tool-Free!) Turn off water supply to toilet. Flush and hold pedal to drain bowl completely. Step on flush pedal and hold open to expose the seal ring in the bowl opening. Use fingers or a plastic pry tool to lift the old seal ring out through the bowl — it sits in a groove around the opening. Clean the seal groove thoroughly with a rag — remove all mineral deposits and old grease. Apply a thin coat of included silicone grease to the new seal ring. Press the new seal firmly into the groove. Ensure it's fully seated all the way around. Release pedal, turn water on, fill bowl, and check for water retention. Frequently Asked Questions Q: My bowl is dry every morning — is this the fix?A: Yes, this is the classic symptom of a failed flush ball seal. The seal can no longer hold water in the bowl, so it slowly drains into the holding tank overnight. Replace the seal ring to restore water retention. Q: Do I need to remove the toilet from the floor?A: No. Unlike many RV toilet repairs, the flush ball seal is installed entirely from above the bowl. Simply hold the pedal open and access the seal groove through the bowl opening. No dismounting required. Q: How often should the flush ball seal be replaced?A: Replace every 2-3 years under normal use, or at the first sign of bowl water loss. If you full-time RV or use harsh holding tank chemicals, inspect annually. The seal is inexpensive — proactive replacement prevents odor problems. Q: Will this stop the holding tank odor in my bathroom?A: Yes, if the odor is coming through the toilet bowl. A worn seal allows tank gases to bypass the flush ball. Combined with good tank vent maintenance, a new seal eliminates bathroom odors. Q: Why does my seal keep failing quickly?A: Frequent seal failures usually indicate mineral buildup from hard water or abrasive chemical treatments. Use a water softener if you have hard water, and consider enzyme-based tank treatments instead of formaldehyde-based products. Q: Is this genuine Dometic or aftermarket?A: This is a high-quality aftermarket replacement manufactured to Dometic OEM specifications. It matches the exact dimensions and material properties of the factory seal at a significantly lower cost. Related Products Pairs with this part: Related Products 385311462 RV Toilet RV Part 13168 RV Toilet Water Valve Kit for Aqua Magic IV Toilets 385316906 Vacuum Breaker RV Part Related Guides & Articles Complete Onan Quiet Diesel RV Generator Tune-Up Best Water Separator Fuel Filter for Diesel & Marine Engines Diesel Fuel Filter Replacement: The Complete Guide
$19.99
iFJF 385314349 RV Toilet Water Valve Kit for Sealand Traveler & VacuFlush Pedal Flush
385314349 RV Toilet Water Valve Assembly — Complete Replacement Kit A constantly running RV toilet wastes fresh water — the most precious resource when boondocking. The iFJF 385314349 replaces the complete water inlet valve on Dometic Sealand Traveler and VacuFlush foot-pedal toilets. This full valve body assembly includes an integrated check valve, inlet screen, and mounting flange — everything needed for a leak-free repair in under 30 minutes. Key Features Complete Assembly: Valve body, built-in anti-siphon check valve, inlet screen, and mounting flange — no need to piece together individual parts. Wide Fitment: Compatible with Sealand Traveler models 110, 111, 210, 211, 510, 511 and VacuFlush models 147, 148 with foot-pedal flush. Built-In Check Valve: Prevents back-siphoning of toilet water into the fresh water system — meets plumbing code requirements for RV applications. Quick-Connect Fittings: Tool-free push-to-connect water line connections — no wrenches needed for plumbing connections. Chemical-Resistant Construction: Seals and body materials withstand RV antifreeze, holding tank chemicals, and hard water mineral deposits. Compatibility Brand Series Models Sealand / Dometic Traveler 110, 111, 210, 211, 510, 511 Sealand / Dometic VacuFlush 147, 148 (foot-pedal models) Specifications Spec Value Part Number 385314349 Valve Type Diaphragm Water Inlet Valve Connection Type Quick-Connect Push Fittings Includes Valve Body, Check Valve, Inlet Screen, Mounting Flange, Hardware Symptoms of a Failing Water Valve Water runs continuously or trickles into toilet bowl when not in use Very weak flush — water barely enters bowl when pedal pressed No water at all when pedal is pressed Water leaking from valve body or connections Unusual hissing or vibrating sounds during flush cycle Toilet fills slowly — taking 30+ seconds for normal water level Installation Guide Shut off RV water supply (turn off pump and disconnect city water connection). Flush toilet to relieve any remaining line pressure. Disconnect water line from valve inlet — press quick-connect release tab and pull. Remove mounting screws securing old valve to toilet base. Install new 385314349 valve assembly. Align mounting holes and tighten screws. Push water line into quick-connect fitting until it clicks — no tools required. Turn water supply back on. Cycle flush pedal several times to purge air. Inspect all connections for leaks. Adjust if needed. Frequently Asked Questions Q: My toilet keeps running — will this fix it?A: Yes, if water is continuously flowing into the bowl even when the pedal isn't pressed, the internal valve diaphragm has failed. Replacing the complete valve assembly is the proper repair. Q: Does this fit the Traveler 511 toilet?A: Yes. The 385314349 fits all Sealand Traveler series models (110, 111, 210, 211, 510, 511) with push-to-connect water fittings. Q: Do I need special tools?A: No. The quick-connect fittings are tool-free. You'll only need a screwdriver for the mounting screws. Complete installation typically takes 20-30 minutes. Q: Will this work with my well water / hard water system?A: Yes. The valve is designed to handle mineral-heavy water. The built-in inlet screen catches sediment and can be cleaned periodically to maintain flow rate. Q: Is this valve anti-siphon?A: Yes. The integrated check valve prevents backflow into your fresh water system, meeting RVIA plumbing standards for toilet water supply connections. Q: What causes water valve failure in RV toilets?A: The most common causes are mineral scale buildup jamming the diaphragm, chemical degradation of internal seals from holding tank treatments, freeze damage in un-winterized systems, and simple wear from years of use. Related Products Pairs with this part: Related Products Water Valve Kit for Sealand 300/310/320 RV Toilets — 385311641 13168 RV Toilet Water Valve Kit for Aqua Magic IV Toilets 385311462 RV Toilet RV Part Related Guides & Articles Complete Onan Quiet Diesel RV Generator Tune-Up Best Water Separator Fuel Filter for Diesel & Marine Engines Diesel Fuel Filter Replacement: The Complete Guide 📖 Related Guide: VacuFlush Toilet Seal Replacement: Step-by-Step Install Guide →
$25.99
iFJF 385316906 Vacuum Breaker Kit for Sealand Traveler Toilets — No Sprayer
385316906 Vacuum Breaker Kit for Sealand Traveler Toilets — Leaking Stopped, No Sprayer Stop your Sealand Traveler RV toilet from leaking with this OEM-grade vacuum breaker repair kit (part number 385316906). Designed specifically for Traveler series toilets WITHOUT the hand sprayer hookup, this kit replaces the worn internal seals and components that cause water leaks, backflow issues, and inconsistent flushing. Whether you're dealing with a slow drip that won't stop or water backing up into the bowl, this kit provides a complete, lasting repair at a fraction of the cost of a new toilet. Key Features OEM-Spec 385316906 Replacement: Manufactured to exact Sealand/Dometic specifications for a guaranteed fit on Traveler series toilets without the hand sprayer option Complete Sealing Kit: Includes vacuum breaker, o-rings, gaskets, check valve components, and all internal seals needed for a full rebuild Stops Water Leaks: Addresses the two most common leak sources — the vacuum breaker seal failure (leaks at the back of the toilet) and check valve deterioration (water leaking into the bowl) Prevents Backflow: Restores proper one-way water flow, preventing contaminated bowl water from siphoning back into your RV's fresh water system DIY-Friendly Installation: Clear, illustrated instructions included — most RV owners complete this repair in 30-45 minutes with basic hand tools Compatibility Brand Model Series Part Number Configuration Sealand Traveler 385316906 Without hand sprayer hookup Dometic Traveler 385316906 Without hand sprayer hookup Important: This kit is for Traveler models WITHOUT the hand sprayer. If your toilet has a hand sprayer attachment, you need kit 385230325 instead (available in our store). Common Symptoms This Kit Fixes Water leaking from the back of the toilet onto the bathroom floor Water slowly filling the bowl when the toilet is not in use Weak or inconsistent flush performance Water hammer or chattering noise during flush cycle Water backing up or gurgling in the bowl after flushing Why Fix Instead of Replace? A new Sealand Traveler toilet costs $400-700. This vacuum breaker kit addresses the most common failure point for under $25. The Traveler series is known for durable ceramic bowls and robust pedal mechanisms — the vacuum breaker is typically the first and only component that fails. Replacing it restores full function and extends your toilet's life by years. This is the same repair a mobile RV tech would perform, and you can do it yourself in under an hour. Frequently Asked Questions Q: How do I know if my Traveler toilet needs this part vs the 385230325 kit?A: Check if your toilet has a hand sprayer attachment (a small hose coming from the back of the toilet with a spray nozzle). If NO sprayer → order this 385316906 kit. If YES sprayer → order our 385230325 kit. The vacuum breaker design is different for each configuration. Q: Can I install this myself, or do I need a mobile RV tech?A: Most RV owners can install this kit themselves. You'll need basic tools: Phillips screwdriver, adjustable wrench, and possibly needle-nose pliers for small o-rings. Turn off the water pump and relieve pressure before starting. Allow 30-45 minutes for first-time installation. Q: Will this stop my toilet from running intermittently?A: If your toilet's water valve cycles on and off while not in use, the vacuum breaker seal is likely the culprit. Replacing it with this kit typically resolves intermittent cycling. If the issue persists after installation, the water valve itself may need replacement. Q: Are these genuine Sealand parts?A: This is an OEM-grade aftermarket kit manufactured to Sealand/Dometic specifications. The materials, dimensions, and tolerances match the original parts. It's functionally identical to the OEM kit at a more accessible price point. Q: How often should the vacuum breaker be replaced?A: There's no fixed replacement interval — replace it when symptoms appear (leaking, backflow, weak flush). In full-time RV use, expect 3-5 years from a vacuum breaker. In occasional/seasonal use, they can last 5-8 years. 📚 Related Guides & Articles RV Toilet Maintenance: Fixing Leaks and Odors Sealand vs Dometic: RV Toilet Parts Compatibility Guide
$23.99
iFJF 387874 Power Stabilizer Switch Harness for Lippert RV — 5th Wheel
Product Overview The 387874 Power Stabilizer Switch Harness for Lippert RV — 5th Wheel Camper is a premium-quality aftermarket replacement part engineered for 3878 Lippert diesel engines vehicles. Designed to meet or exceed OEM specifications, this Switch delivers exceptional performance, durability, and reliability for compatible models owners who demand the best for their vehicles. Key Features Precision Engineering: Manufactured to exact OEM specifications using advanced CNC machining and rigorous quality control processes for perfect fitment every time. Premium Materials: Constructed from high-grade materials selected for maximum durability, corrosion resistance, and long service life under demanding conditions. Direct Fit Installation: Designed as a direct bolt-on replacement with no modifications required — simply remove the old part and install this one using basic hand tools. Quality Certified: Backed by IATF 16949 certified manufacturing standards, ensuring consistent quality and reliability across every unit produced. Comprehensive Warranty: Covered by iFJF's standard warranty against manufacturing defects, with dedicated customer support available to answer your questions. Compatibility Specification Details Vehicle Make Lippert Vehicle Models compatible models Year Range 3878 Engine diesel engines Part Number 387874 Power Stabilizer Switch Harness for Lippert RV — 5th Wheel Camper Replaces OEM OEM specifications Why Choose iFJF Direct? At iFJF Direct, we specialize in providing diesel enthusiasts and professional mechanics with premium aftermarket parts that deliver genuine value. Every product we sell is carefully selected for quality, tested for performance, and backed by our commitment to customer satisfaction. Whether you're maintaining a daily driver, building a competition truck, or servicing a fleet, iFJF has the parts you need with the quality you can trust. Frequently Asked Questions Q: Will this fit my 3878? A: This Switch is specifically designed for 3878 Lippert compatible models with the diesel engines. Always verify your vehicle's exact year, make, model, and engine specification match the compatibility information above before ordering. Q: Is professional installation required? A: Installation difficulty varies by vehicle and skill level. For most applications, this is a direct bolt-on replacement that can be completed with basic hand tools. We always recommend consulting a certified mechanic if you are unsure about any installation procedure. Q: What's included with my purchase? A: Your purchase includes the Switch as shown. Please review the product images and description carefully. If additional hardware or gaskets are required for installation, they are included where noted. Q: What is your shipping and delivery policy? A: iFJF Direct offers fast worldwide shipping. Orders are typically processed within 1-2 business days. Shipping times vary by destination. Free shipping is available on qualifying orders. Contact our support team for specific delivery estimates to your location. Q: What warranty coverage do you provide? A: All iFJF products are warranted against manufacturing defects. Our warranty covers replacement or refund of defective products. Contact our support team with your order number to initiate a warranty claim. We pride ourselves on standing behind every product we sell. Order With Confidence When you order from iFJF Direct, you're getting more than just a Switch — you're getting our commitment to quality, reliability, and customer satisfaction. Every product is backed by our warranty and supported by our knowledgeable customer service team. Order yours today and experience the iFJF difference! Related Guides & Articles Check out these helpful resources from the iFJF blog: RV Maintenance — Complete Diesel Truck & RV Maintenance Schedule 2026 RV Generator Guide — Cummins Onan RV Generator Maintenance Guide 2026
$57.99
iFJF 38920-TR0-A02 Battery Current Sensor for Honda CR-V Civic Acura ILX RDX
Product Overview The 38920-TR0-A02 Battery Current Sensor for Honda CR-V Civic Acura ILX RDX is engineered to exact OEM specifications for guaranteed fit and reliable performance. Whether restoring, upgrading, or replacing a worn factory part, this component delivers the quality that professional mechanics and serious DIYers demand. Key Features Premium Construction: High-grade materials selected for durability in demanding automotive applications. Direct Bolt-On Fit: Uses factory mounting points — no cutting, welding, or fabrication required. Corrosion Resistant: Protected against rust and environmental degradation. OEM or Better: Meets or exceeds factory specifications for fit, finish, and performance. Compatibility Specification Detail Make Honda, Acura Models CR-V, Civic, ILX, RDX Installation Bolt-On (No Fabrication) Installation Verify fitment against your vehicle year/make/model/engine. Allow vehicle to cool completely before beginning. Remove old component, saving hardware unless new hardware is included. Clean mounting surfaces thoroughly. Install using factory torque specifications. Test fit and function before returning to service. Frequently Asked Questions Q: What are symptoms of a bad battery current sensor?A: Check engine light with battery/charging codes (P154A, P154B, P1554-P1557). Other symptoms: battery not charging properly, overnight battery drain, intermittent electrical issues, auto start-stop malfunction, inaccurate battery state-of-charge on dash. Q: Does this fit my 2014 Honda CR-V?A: Yes. Direct OEM-spec replacement for 2012-2016 CR-V (all trims). Also fits 2012-2015 Civic (all trims), 2013-2020 Acura ILX, and 2013-2018 Acura RDX. Verify original part number is 38920-TR0-A02. Q: Will I need to reset or calibrate after installation?A: Yes. Disconnect battery for 10 minutes after install, reconnect, start engine and idle 15 minutes with all accessories off. This allows ECM to relearn sensor parameters. Some models may need scan tool to clear battery management adaptation values. Q: Is this plug-and-play?A: Yes. Sensor mounts on battery negative terminal and connects to existing wiring harness with factory connector. No cutting, splicing, or modification. 10mm socket — 5-minute job for most DIYers. Related Products Browse All iFJF Products → Related Guides & Articles iFJF Blog — Tips, Guides & Product Updates → 📖 Related Guide: Honda Accord 2.4L Air Filter Replacement Guide: CA10467 vs OEM — Read our in-depth maintenance guide for step-by-step instructions.
$67.99
iFJF 39010200 Tank Clamp O-Ring for Pentair Clean & Clear Plus / FNS Plus DE Filters
Product Overview The 39010200 Tank Clamp O-Ring for Pentair Clean & Clear Plus / FNS Plus DE Filters is a precision-engineered replacement part designed to restore proper function and stop leaks in your pool or spa equipment. Manufactured to meet or exceed OEM specifications, this component delivers reliable, long-lasting performance at a fraction of the dealer price. Pool equipment operates in a harsh environment — constant exposure to chlorinated water, UV radiation, temperature swings, and pressure cycles. When seals, O-rings, and internal components degrade, the result is leaks, poor filtration, and higher operating costs. Key Features OEM-Spec Precision: Manufactured to exact dimensional tolerances for guaranteed fit without modifications. Chemical-Resistant Materials: EPDM, Viton, or chemical-grade polymers resist degradation from chlorine, bromine, salt, and UV. Extended Service Life: Premium materials deliver 2-3x the service life of economy alternatives. Easy DIY Installation: Straightforward replacement with basic hand tools — most jobs take 15-30 minutes. Value Pack Savings: Multi-pack options available — stock up and save vs buying singles when applicable. Compatibility Specification Detail Brand Pentair Pool & Spa Replaces Part # 39010200 Material EPDM Rubber / Engineered Polymer Application Residential & Light Commercial Pool/Spa When to Replace Visible Leaks: Water seeping from connections or housings = failed seal or gasket Decreased Performance: Reduced flow, poor filtration = worn internal components Unusual Noise: Grinding or squealing = worn bearings, gears, or impellers Age: Rubber seals should be replaced every 2-3 years as preventive maintenance Hard/Cracked Rubber: O-rings that feel hard or show surface cracks no longer seal properly Installation Tips Turn Off Equipment: Switch off at circuit breaker before working on pool equipment. Release Pressure: Open air relief valve on filter to release system pressure. Clean All Surfaces: Remove old gasket material and debris — clean surface = proper seal. Use Proper Lubricant: Silicone-based pool lube only. NEVER use petroleum jelly — it destroys EPDM. Tighten Evenly: Cross-pattern tightening for multi-bolt connections. Test Before Full Operation: Run briefly and check all connections. Frequently Asked Questions Q: Which Pentair filter models does this fit?A: Compatible with: Clean & Clear Plus cartridge filters (CCP320, CCP420, CCP520), FNS Plus DE filters (FNS Plus 24, 36, 48, 60), and Nautilus FNS DE filters. Any Pentair filter using screw-type tank clamp band with 39010200 seal. Q: How often should I replace the tank O-ring?A: Every 2-3 years under normal residential use. Replace sooner if: water seeping from tank seam, O-ring feels hard/flattened, visible cracks, or O-ring stretched and no longer fits snugly. Commercial pools should replace annually. Q: Do I need lubricant for the new O-ring?A: Yes! Apply silicone-based pool lubricant (Magic Lube or similar) generously to entire O-ring before installation. Helps ring seat properly, prevents pinching, extends seal life. NEVER use petroleum jelly — it degrades EPDM rubber. Q: My filter still leaks after replacing — what now?A: Check: 1) O-ring groove is clean 2) Tank halves properly aligned 3) Clamp band tightened evenly (alternating sides) 4) Spring on clamp has tension 5) Tank rim not cracked or warped from overtightening. Related Products Shop All Pool & Spa Parts → Pool Filter Cartridges & Grids → Related Guides & Articles Pool Filter Maintenance: Complete Seasonal Guide → How to Fix Common Pool Pump Problems →
$39.99
iFJF 3949238 Washer Lid Switch for Whirlpool Kenmore Sears Roper — AP3100001 Replacement
Product Overview When your top-load washer fills with water but refuses to agitate or spin, the lid switch is the #1 suspect. The iFJF 3949238 (AP3100001) is a direct OEM-spec replacement safety interlock switch for Whirlpool-manufactured washing machines sold under the Whirlpool, Kenmore, Sears, Roper, Estate, Inglis, and Crosley brands. This 3-wire plunger-actuated switch tells the control board the lid is securely closed — enabling the motor to run for spin and agitation cycles. A failed switch typically means the washer fills with water but does nothing else. This 10-minute repair restores full function without a costly service call. Key Features 3-Wire Pre-Terminated Connector — Plug-and-play design with the correct OEM-style connector preinstalled. No cutting, splicing, or crimping required — just unplug the old, plug in the new. Wide Brand Coverage — Compatible with top-load washers from Whirlpool, Kenmore (Sears), Roper, Estate, Inglis, and Crosley — all manufactured by Whirlpool Corporation using the same lid switch design. UL-Recognized Safety Interlock — This is a critical safety component that prevents the washer motor from running with the lid open. A properly functioning lid switch is essential for safe operation. Plunger-Actuated Mechanism — The physical plunger is depressed by the lid striker, closing the circuit. Simple, reliable mechanical operation — no electronics to fail. 10-Minute DIY Repair — Two screws and one connector. No disassembly beyond removing the top panel (usually 2 spring clips or screws). Saves $150+ service call fees. Compatibility / Fitment Brand Type Notes Whirlpool Top-Load Washers Direct and belt drive models Kenmore Top-Load (Sears) Whirlpool-manufactured units (model # starts with 110) Roper Top-Load Whirlpool-built economy brand Estate / Inglis Top-Load Whirlpool-built budget brands Crosley Top-Load Whirlpool-manufactured models Technical Specifications Specification Value Part Number 3949238 (AP3100001) Wire Configuration 3-Wire with OEM Connector Actuation Plunger (Mechanical) Function Safety Interlock (Lid Closed = Motor Enabled) Installation Time 10-15 Minutes Why Choose This A service call to diagnose and replace a lid switch typically costs $150-250. This exact OEM-spec replacement switch costs a fraction of that and takes 10 minutes to install with a basic screwdriver. The symptoms of a failed lid switch are unmistakable — the washer fills normally but sits there without agitating or spinning. Before you call a repairman or consider replacing your machine, try this $16 fix. Nearly every "washer fills but won't spin" complaint traces back to this $16 part. Backed by iFJF's quality guarantee. Related Products More in Home Appliances: Threaded Inlet Strainer Pool Part Browse all Appliance Parts — Washers, dryers, and more Shop All iFJF Parts — Complete product catalog Frequently Asked Questions Q: My washer fills with water but won't agitate or spin. Is this the fix?A: Very likely. On Whirlpool/Kenmore/Roper top-load washers, the lid switch must be closed (plunger depressed) for the motor to energize. If your washer fills normally but sits idle afterward, the lid switch is the most common cause. Replace the 3949238 to restore operation. Q: Will this fit my Kenmore 110 series washer?A: Yes. Kenmore model numbers starting with 110 are manufactured by Whirlpool and use this exact lid switch design. The 110-series prefix is the key identifier — if your Kenmore washer starts with 110, this switch fits. Q: How do I test if my lid switch is bad before ordering?A: Unplug the washer. Remove the top panel (typically 2 spring clips at the front corners). Locate the lid switch near the lid hinge. Use a multimeter on continuity mode — press the plunger in: should show continuity. Release: should show open circuit. If either test fails, replace the switch. Q: My washer runs with the lid open. Do I need this?A: YES — replace immediately. A washer that operates with the lid open has a failed (shorted) safety interlock, which is a significant safety hazard. The lid switch should prevent the motor from running when the lid is raised. Replace the 3949238 switch right away. Q: How difficult is installation?A: Easy DIY. Unplug the washer, remove the two spring clips holding the top panel (near the front corners), tilt the panel back, locate the lid switch near the hinge area, remove 2 screws, disconnect the wire connector, install the new switch, reassemble. Total time: 10-15 minutes. Q: Does this switch fit front-load washers?A: No. This is specifically for top-load washing machines with a lift-up lid mechanism. Front-load washers use a door lock assembly, which is a completely different part. Order with Confidence Fast shipping from our US warehouse. Dedicated customer support team ready to answer your questions. Click Add to Cart to get your order started today. Related Guides & Articles Check out these helpful resources from the iFJF blog: Pool Plumbing — Above Ground Pool Plumbing Parts Explained Pool Filter — Pool Filter Maintenance Guide
$19.99