Products

1478 Electric Choke Conversion Kit for Edelbrock 1405/1406 Carburetors The iFJF 1478 Electric Choke Kit converts your manual-choke Edelbrock 1405 (or replaces a worn electric choke on the 1406) to automatic 12V electric choke operation. No more fishing a choke cable through the firewall — just pump the gas once, turn the key, and the thermostatic choke element handles cold-start enrichment automatically. Key Features Direct Fit — Bolt-on replacement for Edelbrock 1405 and 1406 Performer Series carburetors 12V Electric Operation — Connect to any ignition-switched 12V source for automatic choke function Thermostatic Element — Bimetallic spring opens the choke plate progressively as the engine warms up Includes All Hardware — Choke housing, thermostatic element, fast idle cam, linkage, screws, and gasket Adjustable — Rotate the housing to fine-tune choke opening rate for your climate and engine setup Vacuum Pull-Off Compatible — Works with the existing internal vacuum piston on your 1405/1406 Compatibility Carburetor Model Application 1405 Performer (Manual Choke) Converts manual to electric choke 1406 Performer (Electric Choke) Replacement for worn/failed electric choke Installation Overview Remove the manual choke housing (3 screws) from the passenger side of the carburetor Install the new choke housing with the provided gasket Connect the fast idle linkage to the choke shaft Route the 12V wire to an ignition-switched power source Adjust the choke housing index to set the correct opening rate Frequently Asked Questions Q: Will this fit my 1405 carburetor? A: Yes — the 1478 kit is specifically designed as a direct bolt-on conversion for the Edelbrock 1405 manual choke carburetor. It also fits the 1406 as a replacement electric choke unit. Q: Where should I connect the 12V wire? A: Connect to a key-on 12V source such as the ignition coil positive terminal, the IGN terminal on the fuse box, or a switched 12V circuit. Do not connect to constant 12V — the choke element will drain the battery when the engine is off. Q: How do I adjust the choke? A: The choke housing has index marks. Rotate clockwise (richer) for colder climates or engines that need more warm-up enrichment. Rotate counter-clockwise (leaner) for warm climates. The factory setting (center mark) works well for most applications in temperate regions. Q: Do I need to re-jet after installing the electric choke? A: No. The choke only affects cold-start and warm-up enrichment. Once the engine reaches operating temperature, the choke is fully open and has zero effect on the main fuel circuit. Q: Can I install this without removing the carburetor? A: Yes — the choke housing is accessible on the passenger side of the carburetor and can be swapped with the carburetor installed on the engine. The job typically takes 15-30 minutes. 🔗 Related Products from iFJF 1405 Performer 600 CFM Carburetor 1406 Performer 600 CFM Carburetor 📚 Helpful Installation Guides 📖 Diesel Engine Cooling System Flush Guide 📖 GM Truck Tie Rod Upgrade Installation

Read more less

The iFJF EGR Basic Cooler Kit is a direct replacement solution for your 2003-2007 Ford 6.0L Powerstroke's EGR cooling system. Constructed from high-grade aluminum alloy with silicone connections, this kit offers excellent heat dissipation and corrosion resistance for long-term durability. Whether you're replacing a failed EGR cooler or doing preventative maintenance during your bulletproofing project, this kit provides OEM-level fitment at a fraction of dealer pricing. For off-road and competition use only. Key Features & Benefits Aluminum Alloy Construction: High-grade aluminum alloy with excellent heat dissipation properties — resists corrosion and rust for long service life. Silicone Hose Connections: Premium silicone hoses withstand extreme coolant temperatures and pressures without cracking or degrading. Direct OEM Replacement: Engineered to exact OEM specifications for straightforward bolt-on installation with no modifications. Complete Kit: Includes EGR cooler assembly, silicone hoses, gaskets, O-rings, and mounting hardware. Vehicle Compatibility Year Make Model Engine 2003-2007 Ford F-250/F-350 Super Duty 6.0L Powerstroke V8 Technical Specifications Material Aluminum Alloy + Silicone Type EGR Basic Cooler (Direct Replacement) Installation Time 3-5 Hours ⚠️ Important Legal Notice This product is intended for OFF-ROAD AND COMPETITION USE ONLY. It is NOT legal for use on public roads. NOT CARB compliant. Frequently Asked Questions Q: Is this a complete EGR cooler replacement?A: Yes. This kit includes the EGR cooler assembly, silicone hoses, gaskets, O-rings, and all hardware needed for a complete replacement. Q: What causes 6.0L EGR coolers to fail?A: The #1 cause is a clogged oil cooler. When the oil cooler clogs, coolant flow to the EGR cooler is restricted, causing it to overheat and rupture. Always diagnose your oil cooler health before replacing the EGR cooler. Q: Should I install a coolant filter at the same time?A: Absolutely. Installing a coolant filtration system while you're already working on the cooling system is highly recommended to prevent future oil cooler and EGR cooler failures. Related Products 6.0L EGR Cooler Kit (Standard) 6.0L Coolant Filtration System

Read more less

Product OverviewPrecision-engineered EGR block-off delete plug kit for 1985-1988 Chevy 305 TPI (5.0L) and 1987-1988 350 TPI (5.7L) engines in Camaro, Firebird, and C4 Corvette. These TPI engines are notorious for EGR passage clogging causing rough idle, hesitation, and hard hot starts. Our billet block-off plugs provide a permanent, leak-free solution. For off-road and competition use only. Key Features TPI-Specific Design: CAD-engineered to exact 305/350 TPI EGR port dimensions — no universal adapters needed. Billet Construction: Machined from solid billet aluminum — vastly superior to thin stamped steel plates that warp under heat. Resolves Common TPI Issues: Eliminates EGR-related rough idle, part-throttle hesitation, and carbon-clogged intake passages. Complete Plug Kit: Includes EGR valve block-off plug, EGR tube plug, and required gaskets for complete system removal. Compatibility Make Model Engine Year Chevrolet Camaro, Corvette 305 TPI (5.0L) 1985-1988 Chevrolet Camaro, Corvette 350 TPI (5.7L) 1987-1988 Pontiac Firebird, Trans Am 305/350 TPI 1985-1988 Specifications Specification Detail Material Billet Aluminum Application 305/350 TPI EGR Block-Off Fitment 1985-1988 Camaro/Firebird/Corvette Usage Off-Road / Competition Only ⚠️ Off-Road/Competition Use Only. Not CARB-compliant. Check local emissions regulations. Frequently Asked QuestionsQ: Will this fit my 1989 TPI engine?A: This kit is for 1985-1988 TPI engines. 1989+ TPI uses a different EGR mounting pattern. Q: Does installation require removing the intake manifold?A: No. The EGR valve is externally mounted. Basic hand tools, approximately 45-60 minutes. Q: Is an EGR simulator required?A: Yes, removing EGR will trigger a CEL. An EGR simulator or custom PROM chip is recommended. Q: What is your return policy?A: 30-day return policy for unused items in original packaging. Contact us for replacement or refund. Q: How fast is shipping?A: Ships within 1-2 business days from US warehouse. Standard: 3-7 days. Q: Do you offer warranty?A: Yes, 1-year warranty against manufacturing defects. Order with ConfidenceAdd to cart now — free shipping on orders $50+. Contact our support team within 24h for fitment questions.

Read more less

EGR Cooler & Valve Delete Kit — 2018-2019 Ford F-150 3.0L Powerstroke Diesel The iFJF EGR Delete Kit is precision-engineered for the 2018-2019 Ford F-150 equipped with the 3.0L Powerstroke V6 diesel engine. This complete kit eliminates EGR cooler and valve components with CNC-machined aluminum block-off plates and all necessary hardware for a clean installation. Key Features Aluminum Alloy Construction: Lightweight, corrosion-resistant CNC-machined block-off plates Complete Kit: Includes all block-off plates, gaskets, bolts, and hardware Precision Engineering: CNC-machined to exact tolerances for leak-free seal No More Leaking EGR Cooler: Eliminates common 3.0L Powerstroke EGR cooler failure points Cleaner Intake System: Prevents carbon and soot buildup in intake manifold Compatibility Year Make Model Engine 2018-2019 Ford F-150 3.0L Powerstroke V6 Diesel Technical Specifications Specification Detail Material Aluminum Alloy (6061-T6 Billet) Manufacturing CNC-Machined Kit Contents EGR Cooler Block-Off Plate, Valve Block-Off Plate, Gaskets, Bolts Surface Finish Polished / Anodized Why Delete the EGR on Your 3.0L Powerstroke? Prevent Carbon Buildup: EGR systems recirculate exhaust soot into the intake — deleting prevents carbon deposits Lower Intake Temperatures: Eliminating hot EGR gases reduces intake air temperature for denser air charge Improved Reliability: The 3.0L Powerstroke EGR cooler is a known failure point — delete and eliminate the risk Simplified Engine Bay: Removing EGR components frees up space and simplifies maintenance access Frequently Asked Questions Q: Will this fit my 2019 F-150 with the 3.0L diesel?A: Yes, this kit is specifically designed for 2018-2019 Ford F-150 models equipped with the 3.0L Powerstroke V6 turbo diesel engine. Q: Is tuning required?A: Yes, aftermarket ECM tuning is required after installation to prevent check engine lights and optimize engine operation. Q: Are installation instructions included?A: Yes, step-by-step installation guide with torque specs is included. Professional installation recommended. Q: What's included in the kit?A: EGR cooler block-off plate, EGR valve block-off plate, manifold gaskets, mounting bolts, and installation hardware. Q: Is this for off-road use only?A: Yes, this kit is intended for off-road and competition use only. Not CARB compliant. Related Products Explore more products from our EGR & DPF Delete Kits collection: All EGR & DPF Delete Kits — Browse our complete selection Fuel Filters & Water Separators — Protect your fuel system Oil Filters — Premium filtration for diesel engines

Read more less

Product Overview The iFJF EGR Delete Kit for 2011-2023 Ford 6.7L Powerstroke F-250, F-350 Super Duty is a complete solution to permanently eliminate the troublesome Exhaust Gas Recirculation (EGR) system. The factory EGR system routes hot, soot-laden exhaust gas back into the intake manifold — causing carbon buildup, reduced engine efficiency, and premature component wear. When the EGR cooler fails (a common issue on the 6.7L Powerstroke), it can leak coolant into the intake, risking catastrophic engine damage. Our kit completely removes the EGR valve(s) and cooler(s), replaces them with precision CNC-machined billet aluminum and stainless steel block-off components, and restores clean, unobstructed airflow to your engine. Every component is engineered for exact OEM fitment — no cutting, welding, or permanent modifications required. Key Features Complete EGR System Removal: Includes all block-off plates, delete pipes, gaskets, and hardware to fully eliminate the EGR valve and cooler from your 6.7L Powerstroke. CNC Billet 6061-T6 Aluminum Construction: Precision-machined from aerospace-grade aluminum — far stronger and more durable than cast alternatives. Black anodized finish for corrosion resistance. 304 Stainless Steel Components: Cooler delete pipes and block-off plates use 304-grade stainless steel where required for maximum heat tolerance and longevity. OEM-Grade Gaskets & Seals: Multi-layer steel (MLS) and high-temperature composite gaskets ensure a perfect, leak-free seal — no exhaust or coolant leaks after installation. Direct Bolt-On Installation: All components use existing mounting points and hardware locations. Average install time: 4-6 hours with basic hand tools. Prevents Coolant Contamination: By removing the EGR cooler from the coolant circuit, you eliminate the risk of coolant leaking into the intake — one of the most common 6.7L catastrophic failures. Compatibility Chart Year Make Model Engine Trim Notes 2011-2023 Ford F-250 Super Duty 6.7L Powerstroke V8 Turbo Diesel All trims (XL, XLT, Lariat, King Ranch, Platinum, Limited) 2011-2023 Ford F-350 Super Duty 6.7L Powerstroke V8 Turbo Diesel All trims; Single & Dual Rear Wheel 2011-2023 Ford F-450 Super Duty 6.7L Powerstroke V8 Turbo Diesel Chassis Cab & Pickup 2011-2023 Ford F-550 Super Duty 6.7L Powerstroke V8 Turbo Diesel Chassis Cab Specifications Specification Detail Material CNC Billet 6061-T6 Aluminum, 304 Stainless Steel, High-Temp MLS Gaskets Finish Black Anodized (Aluminum); Natural (Stainless Steel) Fitment Type Direct Bolt-On — No Modification Required Estimated Install Time 4-6 Hours (Professional); 6-8 Hours (DIY) Includes Hardware Yes — Complete Grade 10.9 bolt/washer/nut kit included Includes Gaskets Yes — MLS & high-temp composite gaskets Warranty 1-Year Limited Warranty Why Choose iFJF? Precision Engineering: Every component is reverse-engineered from OEM dimensions for guaranteed fit. No "universal fit" guesswork. Proven Materials: We use 6061-T6 billet aluminum and 304 stainless steel — not cheap cast pot metal that cracks under heat cycling. Complete Kit: Everything you need in one box. No extra parts to source, no trips to the hardware store. US-Based Support: Our diesel experts are available to answer installation questions. We actually know these trucks. Frequently Asked Questions Q: Will this kit fit my 2011 Ford F-250 6.7L Powerstroke?A: Yes. This kit is specifically designed for 2011-2023 Ford Super Duty trucks equipped with the 6.7L Powerstroke V8 turbo diesel engine, including F-250, F-350, F-450, and F-550 models. Q: Does installing an EGR delete require tuning?A: Yes — removing the EGR system will trigger a check engine light (CEL) unless the ECU is tuned to disable EGR-related DTCs. A custom tuner or EFI Live-compatible device is required. This kit includes the mechanical components only. Q: Will this void my factory warranty?A: Modifying the emissions system may affect your factory powertrain warranty coverage. We recommend consulting your dealer or warranty provider before installation. This product is intended for off-road/competition use. Q: How difficult is the installation?A: The installation is rated moderate to advanced. You'll need basic hand tools (socket set, wrenches, torque wrench), and mechanical experience with diesel engines is strongly recommended. Professional installation typically takes 4-6 hours. Q: What symptoms tell me my EGR cooler is failing?A: Common signs include: white smoke from the exhaust (coolant burning), unexplained coolant loss, coolant in the oil (milky oil appearance), rough idle, and P0401/P0402 error codes. If you notice these, your EGR cooler may already be leaking — immediate replacement or deletion is recommended. Q: Can I still pass emissions testing after installing this kit?A: This kit is designed for off-road and competition use only. Removing emissions equipment is not compliant with EPA/CARB regulations for on-road vehicles. Check your local and state regulations before purchase. Q: What other maintenance should I consider while installing this kit?A: While the intake is accessible, it's a great opportunity to clean the intake manifold, inspect turbo piping, and consider upgrading to a coolant filtration system. Check out our other 6.7L Powerstroke products for complete engine protection. Q: What's the difference between the EGR valve delete and EGR cooler delete?A: The valve delete blocks exhaust gases from entering the intake at the EGR valve port. The cooler delete removes the EGR cooler entirely from the coolant circuit — this is critical because a failed cooler can leak coolant into the intake and cause hydrolock. Our kit includes both. California Proposition 65 Warning: This product is intended for off-road/competition use only. Not CARB-compliant. Check local regulations before purchase.

Read more less

Replace your failing or failed EGR cooler with the iFJF EGR Cooler Kit, engineered specifically for the 2003-2007 Ford 6.0L Powerstroke. Constructed from premium aluminum alloy for superior heat dissipation and corrosion resistance, this direct-fit replacement kit includes everything needed for a complete EGR cooler service. The included silicone hoses provide enhanced durability over OEM rubber connections. For off-road and competition use only. Key Features & Benefits Premium Aluminum Alloy: Engineered for excellent heat dissipation and long-term corrosion resistance -- outlasts factory EGR coolers in demanding conditions. Silicone Hose Upgrade: High-temperature silicone hoses replace the failure-prone OEM rubber connections for improved reliability. Direct OEM Fitment: Manufactured to exact OEM specifications -- bolts directly into place with no modification or fabrication required. Complete Replacement Kit: Includes EGR cooler, silicone hoses, gaskets, O-rings, and all necessary mounting hardware. Vehicle Compatibility Year Make Model Engine 2003-2007 Ford F-250/F-350 Super Duty 6.0L Powerstroke V8 Technical Specifications Material Aluminum Alloy + Silicone Type EGR Cooler (Direct OEM Replacement) Heat Dissipation Excellent -- Aluminum Construction Installation Time 3-5 Hours Installation Guide Drain coolant before beginning. Remove the intake manifold for access to the EGR cooler. Disconnect coolant lines and unbolt the old cooler. Clean all mounting surfaces. Install the new cooler with fresh gaskets and O-rings. Reinstall the intake manifold with new gaskets (recommended -- not included). Refill and bleed the coolant system properly to prevent air pockets. Professional installation recommended. Budget 3-5 hours of shop labor. Why Choose iFJF? Better Than OEM: Upgraded aluminum alloy and silicone hoses provide superior durability compared to factory rubber connections and mild steel construction. Everything Included: No extra parts-store runs -- all gaskets, O-rings, and hardware come in the box. Lifetime Support: Our diesel specialist team is available for installation questions and technical guidance. Important Legal Notice This product is intended for OFF-ROAD AND COMPETITION USE ONLY. It is NOT legal for use on public roads in the United States. Installation may violate federal, state, and local emissions regulations. NOT CARB compliant. Frequently Asked Questions Q: How do I know if my EGR cooler has failed?A: Key symptoms include: white smoke from the exhaust (sweet-smelling), disappearing coolant with no visible leaks, coolant in the engine oil (milky oil), and excessive pressure in the degas bottle. A failed EGR cooler can hydro-lock your engine -- address it immediately. Q: Should I replace the oil cooler at the same time?A: Yes -- the oil cooler and EGR cooler failures are directly linked. A clogged oil cooler is usually what causes the EGR cooler to fail. Replacing the EGR cooler without addressing a clogged oil cooler will result in repeated failures. Q: Is this a difficult DIY job?A: It is an advanced DIY job. The intake manifold must be removed, which on a 6.0L requires patience and attention to detail. If you are comfortable with engine work, budget a full weekend. Otherwise, professional installation is recommended. Q: Do I need a tune after replacing the EGR cooler?A: If you are replacing with a stock-style cooler on a stock truck, no tuning is needed. If you are doing an EGR delete, an ECU tuner is required to disable EGR-related DTCs. Related Products 6.0L EGR Basic Cooler Kit 6.0L Coolant Filtration System

Read more less

Product Overview Upgrade your 2013-2014 Dodge Ram 6.7L Cummins with this professional-grade egr delete + cooler delete + throttle valve delete + exhaust pipe. Designed for the Ram 3500/4500/5500 Cab & Chassis, this kit delivers improved engine performance, reduced maintenance issues, and enhanced reliability. Whether you're a professional diesel mechanic or a DIY enthusiast, our precision-engineered components provide a bolt-on solution for your Dodge Ram truck. Key Features Precision Fit: Engineered specifically for 2013-2014 Dodge Ram 6.7L Cummins Ram 3500/4500/5500 Cab & Chassis — direct bolt-on installation with no modifications required. Heavy-Duty Construction: Built with industrial-grade materials to withstand extreme temperatures and pressures in high-performance diesel applications. Complete Kit: Includes all necessary hardware — gaskets, bolts, block-off plates, and installation components for a straightforward install. Performance Gains: Eliminates common failure points in the OEM EGR/exhaust system, improving exhaust flow, reducing EGTs (Exhaust Gas Temperatures), and enhancing throttle response. Corrosion Resistant: All components feature corrosion-resistant finishes to withstand road salt, moisture, and extreme weather conditions. Compatibility Year Make Model Engine 2013 Dodge/Ram 3500/4500/5500 Cab & Chassis 6.7L Cummins Diesel 2014 Dodge/Ram 3500/4500/5500 Cab & Chassis 6.7L Cummins Diesel Why Choose iFJF Direct? Quality Assurance: Every component undergoes rigorous quality control inspection before shipping — we stand behind our products. US-Based Support: Our team understands North American diesel trucks. Get expert support when you need it. Fast Shipping: Orders ship from our US warehouses within 1-2 business days. Lifetime Support: Need help with installation? Our diesel specialists are just a message away. Frequently Asked Questions Q: Is this kit compatible with my 2013 Dodge Ram Ram 3500/4500/5500 Cab & Chassis?A: Yes! This kit is designed as a direct bolt-on for 2013-2014 Dodge Ram 6.7L Cummins Ram 3500/4500/5500 Cab & Chassis. No modifications are required for installation on stock vehicles. Q: What tools do I need for installation?A: Basic hand tools including socket set (8mm-19mm), torque wrench, flathead and Phillips screwdrivers, and penetrating oil for rusted fasteners. Most experienced DIY mechanics can complete the installation in 2-4 hours. Q: Will this delete kit trigger a check engine light (CEL)?A: This is a hardware-only kit. For complete functionality, appropriate ECU tuning is recommended to prevent DTCs (Diagnostic Trouble Codes). Professional tuning services are available from third-party providers. Q: Are gaskets and hardware included?A: Yes — all necessary gaskets, bolts, block-off plates, and mounting hardware are included in the kit. We recommend having replacement exhaust manifold gaskets on hand if your vehicle has high mileage. Q: How does this compare to OEM parts?A: Our components are engineered to solve the known failure points in the OEM emissions system. By eliminating problematic EGR coolers, valves, and restrictive exhaust components, you'll experience improved reliability, better fuel economy, and reduced maintenance costs. Q: What material are the block-off plates made from?A: Block-off plates are CNC-machined from 6061-T6 billet aluminum (or 304 stainless steel where noted) — far superior to OEM cast components that are prone to cracking and leaking under heat cycling. Q: Do you offer a warranty?A: Yes! All iFJF Direct products come with a satisfaction guarantee. If you have any issues with fitment or quality, contact our support team for a replacement or refund. ⚠️ Off-Road Use Only: This product is intended for off-road and competition use only. Please check your local, state, and federal regulations before purchasing and installing emissions-related components. Related Products iFJF 2013-2014 6.7L Cummins Dodge Ram Cab & Chassis Throttle Valve Cooler Diesel iFJF 2013-2018 6.7L Cummins Diesel EGR Delete Kit for Cab & Chassis Dodge Ram iFJF 2013-2018 6.7L Dodge RAM 2500 3500 Cummins Diesel EGR Delete Cooler Throttl iFJF 2013-2018 6.7L Dodge Ram 2500 3500 Turbo Diesel Generic 4'' Exhaust Tube Pi

Read more less

Product Overview Upgrade your 2013-2018 Dodge Ram 6.7L Cummins with this professional-grade egr delete + cooler delete + throttle valve delete + exhaust pipe. Designed for the Ram 2500/3500, this kit delivers improved engine performance, reduced maintenance issues, and enhanced reliability. Whether you're a professional diesel mechanic or a DIY enthusiast, our precision-engineered components provide a bolt-on solution for your Dodge Ram truck. Key Features Precision Fit: Engineered specifically for 2013-2018 Dodge Ram 6.7L Cummins Ram 2500/3500 — direct bolt-on installation with no modifications required. Heavy-Duty Construction: Built with industrial-grade materials to withstand extreme temperatures and pressures in high-performance diesel applications. Complete Kit: Includes all necessary hardware — gaskets, bolts, block-off plates, and installation components for a straightforward install. Performance Gains: Eliminates common failure points in the OEM EGR/exhaust system, improving exhaust flow, reducing EGTs (Exhaust Gas Temperatures), and enhancing throttle response. Corrosion Resistant: All components feature corrosion-resistant finishes to withstand road salt, moisture, and extreme weather conditions. Compatibility Year Make Model Engine 2013 Dodge/Ram 2500/3500 6.7L Cummins Diesel 2014 Dodge/Ram 2500/3500 6.7L Cummins Diesel 2015 Dodge/Ram 2500/3500 6.7L Cummins Diesel 2016 Dodge/Ram 2500/3500 6.7L Cummins Diesel 2017 Dodge/Ram 2500/3500 6.7L Cummins Diesel 2018 Dodge/Ram 2500/3500 6.7L Cummins Diesel Why Choose iFJF Direct? Quality Assurance: Every component undergoes rigorous quality control inspection before shipping — we stand behind our products. US-Based Support: Our team understands North American diesel trucks. Get expert support when you need it. Fast Shipping: Orders ship from our US warehouses within 1-2 business days. Lifetime Support: Need help with installation? Our diesel specialists are just a message away. Frequently Asked Questions Q: Is this kit compatible with my 2013 Dodge Ram Ram 2500/3500?A: Yes! This kit is designed as a direct bolt-on for 2013-2018 Dodge Ram 6.7L Cummins Ram 2500/3500. No modifications are required for installation on stock vehicles. Q: What tools do I need for installation?A: Basic hand tools including socket set (8mm-19mm), torque wrench, flathead and Phillips screwdrivers, and penetrating oil for rusted fasteners. Most experienced DIY mechanics can complete the installation in 2-4 hours. Q: Will this delete kit trigger a check engine light (CEL)?A: This is a hardware-only kit. For complete functionality, appropriate ECU tuning is recommended to prevent DTCs (Diagnostic Trouble Codes). Professional tuning services are available from third-party providers. Q: Are gaskets and hardware included?A: Yes — all necessary gaskets, bolts, block-off plates, and mounting hardware are included in the kit. We recommend having replacement exhaust manifold gaskets on hand if your vehicle has high mileage. Q: How does this compare to OEM parts?A: Our components are engineered to solve the known failure points in the OEM emissions system. By eliminating problematic EGR coolers, valves, and restrictive exhaust components, you'll experience improved reliability, better fuel economy, and reduced maintenance costs. Q: What material are the block-off plates made from?A: Block-off plates are CNC-machined from 6061-T6 billet aluminum (or 304 stainless steel where noted) — far superior to OEM cast components that are prone to cracking and leaking under heat cycling. Q: Do you offer a warranty?A: Yes! All iFJF Direct products come with a satisfaction guarantee. If you have any issues with fitment or quality, contact our support team for a replacement or refund. ⚠️ Off-Road Use Only: This product is intended for off-road and competition use only. Please check your local, state, and federal regulations before purchasing and installing emissions-related components. Related Products iFJF 2013-2014 6.7L Cummins Dodge Ram Cab & Chassis Throttle Valve Cooler Diesel iFJF 2013-2014 6.7L Dodge Ram Cummins 3500 4'' Exhaust Tube Pipe/Cab & Chassis T iFJF 2013-2018 6.7L Cummins Diesel EGR Delete Kit for Cab & Chassis Dodge Ram iFJF 2013-2018 6.7L Dodge RAM 2500 3500 Cummins Diesel EGR Delete Cooler Throttl

Read more less

Product Overview Upgrade your 2013-2014 Dodge Ram 6.7L Cummins with this professional-grade egr delete + cooler delete + throttle valve delete. Designed for the Ram 3500/4500/5500 Cab & Chassis, this kit delivers improved engine performance, reduced maintenance issues, and enhanced reliability. Whether you're a professional diesel mechanic or a DIY enthusiast, our precision-engineered components provide a bolt-on solution for your Dodge Ram truck. Key Features Precision Fit: Engineered specifically for 2013-2014 Dodge Ram 6.7L Cummins Ram 3500/4500/5500 Cab & Chassis — direct bolt-on installation with no modifications required. Heavy-Duty Construction: Built with industrial-grade materials to withstand extreme temperatures and pressures in high-performance diesel applications. Complete Kit: Includes all necessary hardware — gaskets, bolts, block-off plates, and installation components for a straightforward install. Performance Gains: Eliminates common failure points in the OEM EGR/exhaust system, improving exhaust flow, reducing EGTs (Exhaust Gas Temperatures), and enhancing throttle response. Corrosion Resistant: All components feature corrosion-resistant finishes to withstand road salt, moisture, and extreme weather conditions. Compatibility Year Make Model Engine 2013 Dodge/Ram 3500/4500/5500 Cab & Chassis 6.7L Cummins Diesel 2014 Dodge/Ram 3500/4500/5500 Cab & Chassis 6.7L Cummins Diesel Why Choose iFJF Direct? Quality Assurance: Every component undergoes rigorous quality control inspection before shipping — we stand behind our products. US-Based Support: Our team understands North American diesel trucks. Get expert support when you need it. Fast Shipping: Orders ship from our US warehouses within 1-2 business days. Lifetime Support: Need help with installation? Our diesel specialists are just a message away. Frequently Asked Questions Q: Is this kit compatible with my 2013 Dodge Ram Ram 3500/4500/5500 Cab & Chassis?A: Yes! This kit is designed as a direct bolt-on for 2013-2014 Dodge Ram 6.7L Cummins Ram 3500/4500/5500 Cab & Chassis. No modifications are required for installation on stock vehicles. Q: What tools do I need for installation?A: Basic hand tools including socket set (8mm-19mm), torque wrench, flathead and Phillips screwdrivers, and penetrating oil for rusted fasteners. Most experienced DIY mechanics can complete the installation in 2-4 hours. Q: Will this delete kit trigger a check engine light (CEL)?A: This is a hardware-only kit. For complete functionality, appropriate ECU tuning is recommended to prevent DTCs (Diagnostic Trouble Codes). Professional tuning services are available from third-party providers. Q: Are gaskets and hardware included?A: Yes — all necessary gaskets, bolts, block-off plates, and mounting hardware are included in the kit. We recommend having replacement exhaust manifold gaskets on hand if your vehicle has high mileage. Q: How does this compare to OEM parts?A: Our components are engineered to solve the known failure points in the OEM emissions system. By eliminating problematic EGR coolers, valves, and restrictive exhaust components, you'll experience improved reliability, better fuel economy, and reduced maintenance costs. Q: What material are the block-off plates made from?A: Block-off plates are CNC-machined from 6061-T6 billet aluminum (or 304 stainless steel where noted) — far superior to OEM cast components that are prone to cracking and leaking under heat cycling. Q: Do you offer a warranty?A: Yes! All iFJF Direct products come with a satisfaction guarantee. If you have any issues with fitment or quality, contact our support team for a replacement or refund. ⚠️ Off-Road Use Only: This product is intended for off-road and competition use only. Please check your local, state, and federal regulations before purchasing and installing emissions-related components. Related Products iFJF 2013-2014 6.7L Dodge Ram Cummins 3500 4'' Exhaust Tube Pipe/Cab & Chassis T iFJF 2013-2018 6.7L Cummins Diesel EGR Delete Kit for Cab & Chassis Dodge Ram iFJF 2013-2018 6.7L Dodge RAM 2500 3500 Cummins Diesel EGR Delete Cooler Throttl iFJF 2013-2018 6.7L Dodge Ram 2500 3500 Turbo Diesel Generic 4'' Exhaust Tube Pi

Read more less

Product Overview Upgrade your 2013-2018 Dodge Ram 6.7L Cummins with this professional-grade egr delete + cooler delete + throttle valve delete. Designed for the Ram 2500/3500, this kit delivers improved engine performance, reduced maintenance issues, and enhanced reliability. Whether you're a professional diesel mechanic or a DIY enthusiast, our precision-engineered components provide a bolt-on solution for your Dodge Ram truck. Key Features Precision Fit: Engineered specifically for 2013-2018 Dodge Ram 6.7L Cummins Ram 2500/3500 — direct bolt-on installation with no modifications required. Heavy-Duty Construction: Built with industrial-grade materials to withstand extreme temperatures and pressures in high-performance diesel applications. Complete Kit: Includes all necessary hardware — gaskets, bolts, block-off plates, and installation components for a straightforward install. Performance Gains: Eliminates common failure points in the OEM EGR/exhaust system, improving exhaust flow, reducing EGTs (Exhaust Gas Temperatures), and enhancing throttle response. Corrosion Resistant: All components feature corrosion-resistant finishes to withstand road salt, moisture, and extreme weather conditions. Compatibility Year Make Model Engine 2013 Dodge/Ram 2500/3500 6.7L Cummins Diesel 2014 Dodge/Ram 2500/3500 6.7L Cummins Diesel 2015 Dodge/Ram 2500/3500 6.7L Cummins Diesel 2016 Dodge/Ram 2500/3500 6.7L Cummins Diesel 2017 Dodge/Ram 2500/3500 6.7L Cummins Diesel 2018 Dodge/Ram 2500/3500 6.7L Cummins Diesel Why Choose iFJF Direct? Quality Assurance: Every component undergoes rigorous quality control inspection before shipping — we stand behind our products. US-Based Support: Our team understands North American diesel trucks. Get expert support when you need it. Fast Shipping: Orders ship from our US warehouses within 1-2 business days. Lifetime Support: Need help with installation? Our diesel specialists are just a message away. Frequently Asked Questions Q: Is this kit compatible with my 2013 Dodge Ram Ram 2500/3500?A: Yes! This kit is designed as a direct bolt-on for 2013-2018 Dodge Ram 6.7L Cummins Ram 2500/3500. No modifications are required for installation on stock vehicles. Q: What tools do I need for installation?A: Basic hand tools including socket set (8mm-19mm), torque wrench, flathead and Phillips screwdrivers, and penetrating oil for rusted fasteners. Most experienced DIY mechanics can complete the installation in 2-4 hours. Q: Will this delete kit trigger a check engine light (CEL)?A: This is a hardware-only kit. For complete functionality, appropriate ECU tuning is recommended to prevent DTCs (Diagnostic Trouble Codes). Professional tuning services are available from third-party providers. Q: Are gaskets and hardware included?A: Yes — all necessary gaskets, bolts, block-off plates, and mounting hardware are included in the kit. We recommend having replacement exhaust manifold gaskets on hand if your vehicle has high mileage. Q: How does this compare to OEM parts?A: Our components are engineered to solve the known failure points in the OEM emissions system. By eliminating problematic EGR coolers, valves, and restrictive exhaust components, you'll experience improved reliability, better fuel economy, and reduced maintenance costs. Q: What material are the block-off plates made from?A: Block-off plates are CNC-machined from 6061-T6 billet aluminum (or 304 stainless steel where noted) — far superior to OEM cast components that are prone to cracking and leaking under heat cycling. Q: Do you offer a warranty?A: Yes! All iFJF Direct products come with a satisfaction guarantee. If you have any issues with fitment or quality, contact our support team for a replacement or refund. ⚠️ Off-Road Use Only: This product is intended for off-road and competition use only. Please check your local, state, and federal regulations before purchasing and installing emissions-related components. Related Products iFJF 2013-2014 6.7L Cummins Dodge Ram Cab & Chassis Throttle Valve Cooler Diesel iFJF 2013-2014 6.7L Dodge Ram Cummins 3500 4'' Exhaust Tube Pipe/Cab & Chassis T iFJF 2013-2018 6.7L Cummins Diesel EGR Delete Kit for Cab & Chassis Dodge Ram iFJF 2013-2018 6.7L Dodge Ram 2500 3500 Turbo Diesel Generic 4'' Exhaust Tube Pi

Read more less

Product Overview The iFJF EGR Delete Block Off Plate Kit is engineered for 1983-1997 Ford F-Series trucks and Broncos with the 5.0L (302) or 5.8L (351W) V8 engines. CNC-machined from 6061-T6 billet aluminum, these plates permanently seal the EGR ports on both the intake and exhaust manifolds. ⚠️ For off-road and competition use only — not street legal in emissions-controlled areas. Key Features CNC-Machined Billet Aluminum — Precision-cut 6061-T6 aluminum plates with a smooth sealing surface. Won't warp or crack like stamped steel alternatives. Complete Kit — Includes intake manifold block-off plate, exhaust manifold block-off plate, high-temperature graphite gaskets, and Grade 8 hardware. Eliminates Carbon Buildup — Removing the EGR system stops exhaust soot from entering your intake manifold, keeping intake ports and valves clean. Improved Throttle Response — Cleaner intake air charge = crisper throttle and more consistent idle quality. Corrosion-Resistant — Natural aluminum finish with protective clear anodizing. Won't rust like steel plates. Compatibility Vehicle Engine Years Ford F150 5.0L 302 / 5.8L 351W 1983-1997 Ford F250 5.0L 302 / 5.8L 351W 1983-1997 Ford F350 5.0L 302 / 5.8L 351W 1983-1997 Ford Bronco 5.0L 302 / 5.8L 351W 1983-1996 Specifications Spec Value Brand iFJF Material 6061-T6 Billet Aluminum Finish Clear Anodized Gasket Material High-Temperature Graphite Hardware Grade 8 Steel Bolts Use Off-Road / Competition Only Why Choose iFJF Generic EGR block-off kits often use thin stamped steel that warps and leaks. Our CNC-machined billet aluminum plates maintain a true flat surface for a leak-free seal. Every kit includes high-temperature graphite gaskets — not cheap paper gaskets that burn through after a few heat cycles. Designed by enthusiasts, for enthusiasts. Installation Instructions Disconnect the battery and allow the engine to cool completely. Locate the EGR valve — mounted on or near the intake manifold on the passenger side of the engine. Remove the EGR valve — disconnect vacuum line, unbolt from the intake manifold. Remove the EGR tube running to the exhaust manifold. Clean the mounting surfaces — use a gasket scraper and brake cleaner to remove old gasket material and carbon deposits. Install block-off plates — place the graphite gasket between the plate and manifold surface. Hand-tighten bolts, then torque to 15-18 ft-lbs in a cross pattern. Cap vacuum lines — plug any open vacuum ports left by the EGR system removal. Frequently Asked Questions Q: What is an EGR delete and why would I do it?A: EGR (Exhaust Gas Recirculation) routes exhaust back into the intake to reduce emissions. Over time, carbon buildup clogs the EGR valve and intake passages, causing rough idle, poor performance, and reduced fuel economy. Deleting it cleans up the intake path for improved throttle response — for off-road and competition use only. Q: Does this kit include everything I need?A: Yes. The kit includes aluminum block-off plates for both the intake manifold port and exhaust manifold port, plus high-temperature gaskets and Grade 8 hardware. Everything needed for a complete installation. Q: Will this trigger a check engine light?A: On OBD-I vehicles (pre-1996), typically no. On 1996-1997 OBD-II vehicles, removing the EGR system may trigger a P0401 code. This kit is intended for off-road use where emissions compliance is not required. Q: Does this fit the 5.0L and 5.8L?A: Yes. The plate pattern fits both the 5.0L (302) and 5.8L (351W) Windsor V8 engines found in 1983-1997 Ford trucks and Broncos. Always verify your EGR valve mounting pattern before ordering. Q: Is this for diesel or gas engines?A: This kit is for the GASOLINE 5.0L/5.8L V8 engines. Not for diesel applications. For 6.4L Powerstroke diesel EGR delete, see our separate diesel kit. Related Products EGR Valve Delete Kit for 6.4 Powerstroke Diesel EGR Delete Block Off for Ford Mustang 2.8L 4.9L 5.0L EGR Block Off Plate Kit for Toyota 20R 22RE

Read more less

Product OverviewCNC-machined billet aluminum EGR delete block-off plate kit for 1983-1997 Ford F-150, F-250, F-350, and Bronco with 4.9L 300 I6, 5.0L 302, 5.8L 351W, and 7.5L 460 engines. This kit eliminates the problematic EGR system that causes carbon buildup, rough idle, and reduced performance. Precision-cut for perfect sealing with included gaskets and hardware. For off-road and competition use only. Key Features Billet Aluminum: CNC-machined from 6061-T6 billet aluminum for superior strength and corrosion resistance — far more durable than stamped steel alternatives. Complete Kit: Includes block-off plate, high-temperature gasket, and Grade 8 mounting hardware — everything needed for a leak-free installation. Eliminates Carbon Buildup: By removing the EGR system, you prevent exhaust gas recirculation that causes intake manifold carbon deposits, rough idle, and throttle body contamination. Precision Fit: CAD-designed to exact OEM EGR valve mounting dimensions — no modification, drilling, or grinding required. Cleaner Engine Bay: Removes cluttered EGR vacuum lines, solenoid, and valve for a simplified, professional-looking engine compartment. Compatibility Make Model Engine Year Ford F-150, F-250, F-350, Bronco 4.9L 300 I6, 5.0L 302, 5.8L 351W, 7.5L 460 1983-1997 Specifications Specification Detail Material 6061-T6 Billet Aluminum Finish Natural Machined Includes Block-Off Plate + Gasket + Hardware Application EGR Valve Block-Off Usage Off-Road / Competition Only Why Choose iFJFAt iFJF Direct, we engineer performance solutions for enthusiasts who demand quality. Every product is CNC-machined to exact specifications and backed by our 1-year warranty. We ship from our US warehouse with fast, tracked delivery. ⚠️ Disclaimer: This product is intended for off-road and competition use only. It is not CARB-compliant and may not be legal for on-highway use in your jurisdiction. Frequently Asked QuestionsQ: Is this EGR delete kit street legal?A: No. EGR deletes are intended for off-road, racing, and competition use only. Removing emissions equipment may violate federal and state laws. Check local regulations before installation. Q: Will this trigger a check engine light?A: Yes, removing the EGR system will trigger a check engine light on OBD-I and OBD-II vehicles. An EGR simulator or custom ECU tune is recommended. Q: Do I need special tools?A: Basic hand tools — ratchet, socket set, gasket scraper. Installation takes approximately 30-60 minutes depending on engine bay access. Q: What is your return policy?A: We offer a 30-day return policy for unused items in original packaging. Contact us for a replacement or full refund if you receive a defective product. Q: How fast is shipping?A: Orders ship within 1-2 business days from our US warehouse. Standard shipping takes 3-7 business days. Expedited options available at checkout. Q: Do you offer warranty?A: Yes, all iFJF products come with a 1-year warranty against manufacturing defects. Order with ConfidenceReady to simplify your engine bay? Add to cart now and enjoy free shipping on orders $50+. Questions? Contact our support team — we respond within 24 hours.

Read more less

Product OverviewCNC-machined EGR delete block-off plate kit for 1996-2009 Chevrolet Silverado, Suburban, Tahoe, and GMC Sierra/Yukon with 4.3L V6 and 5.7L V8 CPI (Vortec) engines. The CPI engine's EGR system is a known failure point causing carbon-clogged intake passages and rough running. Our precision billet plate provides a permanent, leak-free block-off. For off-road and competition use only. Key Features CPI Engine Specific: CAD-engineered for 1996-2009 GM CPI (Vortec) platform — not a universal kit. Billet Aluminum: CNC-machined from solid 6061-T6 aluminum — superior to stamped steel plates. Carbon Buildup Solution: Permanently eliminates EGR carbon clogging causing the infamous Vortec rough idle and intake contamination. Complete Install Kit: Includes plate, high-temperature gasket, and Grade 10.9 hardware. Compatibility Make Model Engine Year Chevrolet/GMC Silverado/Sierra 1500/2500 4.3L V6, 5.7L V8 CPI 1996-2009 Chevrolet/GMC Suburban/Yukon/Tahoe 4.3L V6, 5.7L V8 CPI 1996-2009 Specifications Specification Detail Material 6061-T6 Billet Aluminum Application 4.3L/5.7L CPI EGR Block-Off Fitment 1996-2009 GM Trucks & SUVs Usage Off-Road / Competition Only ⚠️ Off-Road/Competition Use Only. Not CARB-compliant. Frequently Asked QuestionsQ: Will this work on my 5.3L Vortec?A: No. This kit is for 4.3L V6 and 5.7L V8 CPI engines from 1996-2009. 5.3L LM7/L59 uses a different EGR system. Q: Does removing EGR affect fuel economy?A: EGR delete typically has minimal impact on fuel economy when paired with a proper tune. Custom ECU tune recommended. Q: Return policy?A: 30-day return for unused items. Contact us for replacement or refund. Q: Shipping time?A: 1-2 business days from US warehouse. Standard: 3-7 days. Q: Warranty?A: 1-year warranty against manufacturing defects. Order with ConfidenceFree shipping on orders $50+. Contact us for fitment verification — we respond within 24 hours.

Read more less

Product Overview Upgrade your 2011-2023 Ford 6.7L Powerstroke with this professional-grade egr delete. Designed for the F-250/F-350/F-450 Super Duty, this kit delivers improved engine performance, reduced maintenance issues, and enhanced reliability. Whether you're a professional diesel mechanic or a DIY enthusiast, our precision-engineered components provide a bolt-on solution for your Ford truck. Key Features Precision Fit: Engineered specifically for 2011-2023 Ford 6.7L Powerstroke F-250/F-350/F-450 Super Duty — direct bolt-on installation with no modifications required. Heavy-Duty Construction: Built with industrial-grade materials to withstand extreme temperatures and pressures in high-performance diesel applications. Complete Kit: Includes all necessary hardware — gaskets, bolts, block-off plates, and installation components for a straightforward install. Performance Gains: Eliminates common failure points in the OEM EGR/exhaust system, improving exhaust flow, reducing EGTs (Exhaust Gas Temperatures), and enhancing throttle response. Corrosion Resistant: All components feature corrosion-resistant finishes to withstand road salt, moisture, and extreme weather conditions. Compatibility Year Make Model Engine 2011 Ford F-250/F-350/F-450/F-550 Super Duty 6.7L Powerstroke Diesel 2012 Ford F-250/F-350/F-450/F-550 Super Duty 6.7L Powerstroke Diesel 2013 Ford F-250/F-350/F-450/F-550 Super Duty 6.7L Powerstroke Diesel 2014 Ford F-250/F-350/F-450/F-550 Super Duty 6.7L Powerstroke Diesel 2015 Ford F-250/F-350/F-450/F-550 Super Duty 6.7L Powerstroke Diesel 2016 Ford F-250/F-350/F-450/F-550 Super Duty 6.7L Powerstroke Diesel 2017 Ford F-250/F-350/F-450/F-550 Super Duty 6.7L Powerstroke Diesel 2018 Ford F-250/F-350/F-450/F-550 Super Duty 6.7L Powerstroke Diesel 2019 Ford F-250/F-350/F-450/F-550 Super Duty 6.7L Powerstroke Diesel 2020 Ford F-250/F-350/F-450/F-550 Super Duty 6.7L Powerstroke Diesel 2021 Ford F-250/F-350/F-450/F-550 Super Duty 6.7L Powerstroke Diesel 2022 Ford F-250/F-350/F-450/F-550 Super Duty 6.7L Powerstroke Diesel 2023 Ford F-250/F-350/F-450/F-550 Super Duty 6.7L Powerstroke Diesel Why Choose iFJF Direct? Quality Assurance: Every component undergoes rigorous quality control inspection before shipping — we stand behind our products. US-Based Support: Our team understands North American diesel trucks. Get expert support when you need it. Fast Shipping: Orders ship from our US warehouses within 1-2 business days. Lifetime Support: Need help with installation? Our diesel specialists are just a message away. Frequently Asked Questions Q: Is this kit compatible with my 2011 Ford F-250/F-350/F-450 Super Duty?A: Yes! This kit is designed as a direct bolt-on for 2011-2023 Ford 6.7L Powerstroke F-250/F-350/F-450 Super Duty. No modifications are required for installation on stock vehicles. Q: What tools do I need for installation?A: Basic hand tools including socket set (8mm-19mm), torque wrench, flathead and Phillips screwdrivers, and penetrating oil for rusted fasteners. Most experienced DIY mechanics can complete the installation in 2-4 hours. Q: Will this delete kit trigger a check engine light (CEL)?A: This is a hardware-only kit. For complete functionality, appropriate ECU tuning is recommended to prevent DTCs (Diagnostic Trouble Codes). Professional tuning services are available from third-party providers. Q: Are gaskets and hardware included?A: Yes — all necessary gaskets, bolts, block-off plates, and mounting hardware are included in the kit. We recommend having replacement exhaust manifold gaskets on hand if your vehicle has high mileage. Q: How does this compare to OEM parts?A: Our components are engineered to solve the known failure points in the OEM emissions system. By eliminating problematic EGR coolers, valves, and restrictive exhaust components, you'll experience improved reliability, better fuel economy, and reduced maintenance costs. Q: What material are the block-off plates made from?A: Block-off plates are CNC-machined from 6061-T6 billet aluminum (or 304 stainless steel where noted) — far superior to OEM cast components that are prone to cracking and leaking under heat cycling. Q: Do you offer a warranty?A: Yes! All iFJF Direct products come with a satisfaction guarantee. If you have any issues with fitment or quality, contact our support team for a replacement or refund. ⚠️ Off-Road Use Only: This product is intended for off-road and competition use only. Please check your local, state, and federal regulations before purchasing and installing emissions-related components.

Read more less

Product Overview Upgrade your 2013-2018 Dodge Ram 6.7L Cummins with this professional-grade egr delete. Designed for the Ram 3500/4500/5500 Cab & Chassis, this kit delivers improved engine performance, reduced maintenance issues, and enhanced reliability. Whether you're a professional diesel mechanic or a DIY enthusiast, our precision-engineered components provide a bolt-on solution for your Dodge Ram truck. Key Features Precision Fit: Engineered specifically for 2013-2018 Dodge Ram 6.7L Cummins Ram 3500/4500/5500 Cab & Chassis — direct bolt-on installation with no modifications required. Heavy-Duty Construction: Built with industrial-grade materials to withstand extreme temperatures and pressures in high-performance diesel applications. Complete Kit: Includes all necessary hardware — gaskets, bolts, block-off plates, and installation components for a straightforward install. Performance Gains: Eliminates common failure points in the OEM EGR/exhaust system, improving exhaust flow, reducing EGTs (Exhaust Gas Temperatures), and enhancing throttle response. Corrosion Resistant: All components feature corrosion-resistant finishes to withstand road salt, moisture, and extreme weather conditions. Compatibility Year Make Model Engine 2013 Dodge/Ram 3500/4500/5500 Cab & Chassis 6.7L Cummins Diesel 2014 Dodge/Ram 3500/4500/5500 Cab & Chassis 6.7L Cummins Diesel 2015 Dodge/Ram 3500/4500/5500 Cab & Chassis 6.7L Cummins Diesel 2016 Dodge/Ram 3500/4500/5500 Cab & Chassis 6.7L Cummins Diesel 2017 Dodge/Ram 3500/4500/5500 Cab & Chassis 6.7L Cummins Diesel 2018 Dodge/Ram 3500/4500/5500 Cab & Chassis 6.7L Cummins Diesel Why Choose iFJF Direct? Quality Assurance: Every component undergoes rigorous quality control inspection before shipping — we stand behind our products. US-Based Support: Our team understands North American diesel trucks. Get expert support when you need it. Fast Shipping: Orders ship from our US warehouses within 1-2 business days. Lifetime Support: Need help with installation? Our diesel specialists are just a message away. Frequently Asked Questions Q: Is this kit compatible with my 2013 Dodge Ram Ram 3500/4500/5500 Cab & Chassis?A: Yes! This kit is designed as a direct bolt-on for 2013-2018 Dodge Ram 6.7L Cummins Ram 3500/4500/5500 Cab & Chassis. No modifications are required for installation on stock vehicles. Q: What tools do I need for installation?A: Basic hand tools including socket set (8mm-19mm), torque wrench, flathead and Phillips screwdrivers, and penetrating oil for rusted fasteners. Most experienced DIY mechanics can complete the installation in 2-4 hours. Q: Will this delete kit trigger a check engine light (CEL)?A: This is a hardware-only kit. For complete functionality, appropriate ECU tuning is recommended to prevent DTCs (Diagnostic Trouble Codes). Professional tuning services are available from third-party providers. Q: Are gaskets and hardware included?A: Yes — all necessary gaskets, bolts, block-off plates, and mounting hardware are included in the kit. We recommend having replacement exhaust manifold gaskets on hand if your vehicle has high mileage. Q: How does this compare to OEM parts?A: Our components are engineered to solve the known failure points in the OEM emissions system. By eliminating problematic EGR coolers, valves, and restrictive exhaust components, you'll experience improved reliability, better fuel economy, and reduced maintenance costs. Q: What material are the block-off plates made from?A: Block-off plates are CNC-machined from 6061-T6 billet aluminum (or 304 stainless steel where noted) — far superior to OEM cast components that are prone to cracking and leaking under heat cycling. Q: Do you offer a warranty?A: Yes! All iFJF Direct products come with a satisfaction guarantee. If you have any issues with fitment or quality, contact our support team for a replacement or refund. ⚠️ Off-Road Use Only: This product is intended for off-road and competition use only. Please check your local, state, and federal regulations before purchasing and installing emissions-related components. Related Products iFJF 2013-2014 6.7L Cummins Dodge Ram Cab & Chassis Throttle Valve Cooler Diesel iFJF 2013-2014 6.7L Dodge Ram Cummins 3500 4'' Exhaust Tube Pipe/Cab & Chassis T iFJF 2013-2018 6.7L Dodge RAM 2500 3500 Cummins Diesel EGR Delete Cooler Throttl iFJF 2013-2018 6.7L Dodge Ram 2500 3500 Turbo Diesel Generic 4'' Exhaust Tube Pi

Read more less

Product Overview Upgrade your 2013-2018 Dodge Ram 6.7L Cummins with this professional-grade egr delete. Designed for the Ram 3500/4500/5500 Cab & Chassis, this kit delivers improved engine performance, reduced maintenance issues, and enhanced reliability. Whether you're a professional diesel mechanic or a DIY enthusiast, our precision-engineered components provide a bolt-on solution for your Dodge Ram truck. Key Features Precision Fit: Engineered specifically for 2013-2018 Dodge Ram 6.7L Cummins Ram 3500/4500/5500 Cab & Chassis — direct bolt-on installation with no modifications required. Heavy-Duty Construction: Built with industrial-grade materials to withstand extreme temperatures and pressures in high-performance diesel applications. Complete Kit: Includes all necessary hardware — gaskets, bolts, block-off plates, and installation components for a straightforward install. Performance Gains: Eliminates common failure points in the OEM EGR/exhaust system, improving exhaust flow, reducing EGTs (Exhaust Gas Temperatures), and enhancing throttle response. Corrosion Resistant: All components feature corrosion-resistant finishes to withstand road salt, moisture, and extreme weather conditions. Compatibility Year Make Model Engine 2013 Dodge/Ram 3500/4500/5500 Cab & Chassis 6.7L Cummins Diesel 2014 Dodge/Ram 3500/4500/5500 Cab & Chassis 6.7L Cummins Diesel 2015 Dodge/Ram 3500/4500/5500 Cab & Chassis 6.7L Cummins Diesel 2016 Dodge/Ram 3500/4500/5500 Cab & Chassis 6.7L Cummins Diesel 2017 Dodge/Ram 3500/4500/5500 Cab & Chassis 6.7L Cummins Diesel 2018 Dodge/Ram 3500/4500/5500 Cab & Chassis 6.7L Cummins Diesel Why Choose iFJF Direct? Quality Assurance: Every component undergoes rigorous quality control inspection before shipping — we stand behind our products. US-Based Support: Our team understands North American diesel trucks. Get expert support when you need it. Fast Shipping: Orders ship from our US warehouses within 1-2 business days. Lifetime Support: Need help with installation? Our diesel specialists are just a message away. Frequently Asked Questions Q: Is this kit compatible with my 2013 Dodge Ram Ram 3500/4500/5500 Cab & Chassis?A: Yes! This kit is designed as a direct bolt-on for 2013-2018 Dodge Ram 6.7L Cummins Ram 3500/4500/5500 Cab & Chassis. No modifications are required for installation on stock vehicles. Q: What tools do I need for installation?A: Basic hand tools including socket set (8mm-19mm), torque wrench, flathead and Phillips screwdrivers, and penetrating oil for rusted fasteners. Most experienced DIY mechanics can complete the installation in 2-4 hours. Q: Will this delete kit trigger a check engine light (CEL)?A: This is a hardware-only kit. For complete functionality, appropriate ECU tuning is recommended to prevent DTCs (Diagnostic Trouble Codes). Professional tuning services are available from third-party providers. Q: Are gaskets and hardware included?A: Yes — all necessary gaskets, bolts, block-off plates, and mounting hardware are included in the kit. We recommend having replacement exhaust manifold gaskets on hand if your vehicle has high mileage. Q: How does this compare to OEM parts?A: Our components are engineered to solve the known failure points in the OEM emissions system. By eliminating problematic EGR coolers, valves, and restrictive exhaust components, you'll experience improved reliability, better fuel economy, and reduced maintenance costs. Q: What material are the block-off plates made from?A: Block-off plates are CNC-machined from 6061-T6 billet aluminum (or 304 stainless steel where noted) — far superior to OEM cast components that are prone to cracking and leaking under heat cycling. Q: Do you offer a warranty?A: Yes! All iFJF Direct products come with a satisfaction guarantee. If you have any issues with fitment or quality, contact our support team for a replacement or refund. ⚠️ Off-Road Use Only: This product is intended for off-road and competition use only. Please check your local, state, and federal regulations before purchasing and installing emissions-related components. Related Products iFJF 2013-2014 6.7L Cummins Dodge Ram Cab & Chassis Throttle Valve Cooler Diesel iFJF 2013-2014 6.7L Dodge Ram Cummins 3500 4'' Exhaust Tube Pipe/Cab & Chassis T iFJF 2013-2018 6.7L Cummins Diesel EGR Delete Kit for Cab & Chassis Dodge Ram iFJF 2013-2018 6.7L Dodge RAM 2500 3500 Cummins Diesel EGR Delete Cooler Throttl

Read more less

Product Overview The EGR Delete Kit & Exhaust Cap for 1996-2004 Ford Mustang is purpose-built for the Modular V8 platform that defined the SN95 and New Edge eras. Compatible with 4.6L 2V GT, 4.6L 4V SVT Cobra, and 5.4L GT500 engines, this kit eliminates the Exhaust Gas Recirculation system that introduces hot exhaust gases and carbon deposits into your intake — robbing power, fouling the throttle body, and increasing intake air temperatures. For off-road/competition use only. Key Features Complete EGR Block-Off Solution: Seals the EGR valve port on the intake manifold, the EGR tube port on the exhaust manifold, and the EGR vacuum port on the throttle body — three-point seal for a clean delete. CNC Billet 6061-T6 Aluminum Plates: Precision-machined block-off plates with laser-cut gaskets — no warping, no exhaust leaks. Steel Exhaust Cap: High-temperature steel cap for the exhaust manifold EGR tube port. Won't crack or leak under sustained exhaust gas temperatures (1,200°F+). Cleaner Intake System: No more exhaust soot and oily carbon deposits coating your throttle body, IAC valve, and intake manifold. Better idle quality and throttle response. Reduced Intake Air Temps: Stopping 500°F+ exhaust gases from entering the intake manifold lowers IATs — critical for supercharged and nitrous applications. Compatibility Year Make Model Engine 1996-2004 Ford Mustang GT (2V) 4.6L Modular V8 SOHC 1996-1998 Ford Mustang SVT Cobra (4V) 4.6L Modular V8 DOHC 1999-2001 Ford Mustang SVT Cobra (4V) 4.6L Modular V8 DOHC 2003-2004 Ford Mustang SVT Cobra (4V Supercharged) 4.6L Modular V8 DOHC SC 2005-2006 Ford Mustang GT500 (4V Supercharged) 5.4L Modular V8 DOHC SC Installation Notes ⚠️ Tuning Required: ECU reflash necessary to disable EGR DTCs. SCT X4, DiabloSport, or HP Tuners compatible. ⚠️ Off-Road Only: Not emissions-legal for on-road use in the United States. Installation time: 2-3 hours with basic hand tools. EGR tube removal on the exhaust manifold requires penetrating oil — these bolts are often seized after 20+ years. Frequently Asked Questions Q: Does this require a tune?A: Yes. Removing the EGR system on 1996-2004 Mustang Modular V8 engines will trigger a check engine light (P0401/P0402). You will need an SCT, DiabloSport, or custom tune to disable EGR-related DTCs. This kit includes hardware only.Q: Will this fit my 2003 Mustang GT 4.6L?A: Yes. This kit fits all 1996-2004 Mustang GT (2V), SVT Cobra (4V), and GT500 models with the 4.6L and 5.4L Modular V8 engines. Covers both SN95 (1996-1998) and New Edge (1999-2004) platforms.Q: What's included in the kit?A: Includes: EGR valve block-off plate (billet 6061-T6 aluminum), EGR tube exhaust manifold cap (steel), throttle body EGR port cap, all gaskets, and mounting hardware. Complete bolt-on kit.Q: Is this legal for street use?A: No. This EGR delete kit is for OFF-ROAD / COMPETITION USE ONLY. Removing emissions equipment from on-road vehicles is prohibited under EPA and CARB regulations. Check local laws before purchasing.

Read more less

Overview This Complete EGR Delete Kit eliminates the exhaust gas recirculation system on 1986-1995 Ford F-Series trucks and Broncos, removing a common failure point on high-mileage Ford pushrod engines. The kit includes precision-machined block-off plates and an exhaust manifold cap — everything needed to cleanly remove the EGR valve, EGR tube, and related vacuum components. By blocking exhaust gas from re-entering the intake manifold, this kit eliminates carbon buildup on intake valves, restores crisp throttle response, and simplifies the engine bay. ⚠️ Off-Road / Competition Use Only: EGR removal disables a federally mandated emissions control system. This product is intended exclusively for off-road vehicles, competition vehicles, and vehicles not registered for highway use. Not legal for sale or use in California or other states with emissions testing requirements. Key Features Complete Kit: EGR valve block-off plate + exhaust manifold cap + gaskets + hardware Precision CNC Machined: 6061-T6 billet aluminum plates with exact OEM port dimensions Stops Carbon Buildup: No more exhaust soot coating your intake manifold and valves Cleaner Engine Bay: Eliminates EGR valve, vacuum solenoid, and tubing — easier maintenance access Broad Ford Coverage: 2.8L V6, 4.9L I6, 5.0L V8, 5.8L V8, 7.5L V8 (1986-1995) Includes Exhaust Manifold Cap: Seals the EGR port on the exhaust side — no leaks, no welding Compatibility Table Brand Model Engine Year Range Ford F-150 4.9L I6 / 5.0L V8 / 5.8L V8 1986-1995 Ford F-250 4.9L I6 / 5.0L V8 / 5.8L V8 / 7.5L V8 1986-1995 Ford F-350 5.8L V8 / 7.5L V8 1986-1995 Ford Bronco 4.9L I6 / 5.0L V8 / 5.8L V8 1986-1995 Ford Ranger 2.8L V6 1986-1988 Specifications Spec Value Material 6061-T6 Billet Aluminum Finish Natural / Anodized Includes EGR Block-Off Plate, Exhaust Manifold Cap, Gaskets, Stainless Hardware Installation Bolt-on — no welding required Compliance For Off-Road / Competition Use Only Benefits of EGR Delete Eliminates Intake Carbon: EGR recirculates sooty exhaust into the intake, building carbon deposits over time. Removing it keeps your intake clean. Improved Throttle Response: Without exhaust gas diluting the intake charge, combustion is more efficient — especially at part throttle. Lower Intake Air Temps: Hot exhaust gas raises intake temperatures; blocking it helps maintain charge density. Simplified Diagnostics: Failed EGR valves cause rough idle, stalling, and check engine codes. Removal eliminates the variable. Installation Notes Basic hand tools required. Estimated install time: 1-2 hours. Includes detailed instructions. EGR valve removal may trigger a check engine light on OBD-I (pre-1996) vehicles — this is expected and does not affect driveability. Professional installation recommended. FAQ Q: Is this kit legal for street use?A: No. EGR removal disables a federally required emissions control system. This kit is for off-road vehicles, competition/race vehicles, and vehicles not registered for highway use only. Not CARB compliant — not for sale or use in California. Q: Will this cause a check engine light?A: On OBD-I vehicles (pre-1996), the check engine light may illuminate but does not affect engine operation. On OBD-II vehicles (1996+), EGR delete requires ECU tuning to prevent a persistent CEL and potential limp mode. Q: Does this fit the 5.0L HO Mustang engine?A: This kit is designed for truck intake manifolds (F-150/Bronco). The Mustang 5.0L HO uses a different EGR configuration. Check fitment before ordering. Q: What gaskets are included?A: The kit includes both the EGR valve block-off gasket and the exhaust manifold cap gasket. Both are high-temperature graphite composite rated for exhaust temperatures.

Read more less

Product Overview The EGR Delete Kit for 2004-2005 Duramax 6.6L LLY is engineered to eliminate the restrictive factory EGR system on 2004.5-2005 Chevrolet Silverado and GMC Sierra HD trucks with the 6.6L LLY Duramax diesel engine. By removing the EGR valve and cooler, this kit prevents carbon buildup, reduces exhaust gas temperatures (EGTs), and improves turbocharger response. All components are CNC-machined from premium aluminum and stainless steel for maximum durability under extreme heat cycling. ⚠️ IMPORTANT: This kit is intended for OFF-ROAD / COMPETITION USE ONLY. EGR delete modifications are not EPA/CARB compliant for on-road vehicles. ECU tuning is required to disable EGR-related diagnostic trouble codes (DTCs). Key Features Complete EGR Elimination — Block-off plate, high-flow intake elbow, and coolant reroute hose included to fully bypass the factory EGR cooler and valve assembly. CNC-Machined Aluminum Construction — Intake elbow precision-machined from 6061 aluminum with smooth internal walls for unrestricted airflow and 78.6% increased flow over factory. Nickel-Plated Steel Block-Off Plate — Corrosion-resistant nickel plating withstands exhaust temperatures up to 1,200°F without warping or cracking. Lower EGTs — Eliminating exhaust gas recirculation reduces combustion chamber temperatures by 100-200°F under load, protecting pistons and turbocharger. Prevents Carbon Buildup — Stops soot and carbon deposits from entering the intake manifold, keeping your intercooler and intake tract clean. Direct Bolt-On Fit — Designed as a direct replacement for factory components. No cutting, welding, or permanent modification required. Compatibility Chart Year Make Model Engine 2004.5-2005 Chevrolet Silverado 2500HD 6.6L LLY Duramax 2004.5-2005 Chevrolet Silverado 3500HD 6.6L LLY Duramax 2004.5-2005 GMC Sierra 2500HD 6.6L LLY Duramax 2004.5-2005 GMC Sierra 3500HD 6.6L LLY Duramax Package Includes Component Qty Material Nickel-Plated Steel Block-Off Plate 1 Nickel-Plated Steel High Flow Intake Elbow 1 6061 Billet Aluminum Coolant Bypass Hose (430mm) 1 Silicone, High-Temp Hose Clamps 2 Stainless Steel Bolts & Hardware Pack 7 Grade 10.9 Steel Intake Elbow O-Ring 1 High-Temp Rubber Specifications Specification Value Intake Elbow Material 6061 Billet Aluminum Block-Off Plate Nickel-Plated Steel Coolant Hose 430mm (17"), Silicone High-Temp Flow Increase Up to 78.6% Over Factory SKU ER-0030 Why Choose This Kit Proven Design — The standard EGR delete configuration for LLY Duramax engines. Thousands of owners have upgraded with this exact setup. Premium Materials — Nickel-plated steel and 6061 aluminum outlast plain steel and cast alternatives. Fast US Shipping — Ships from US warehouse. Most orders delivered in 3-7 business days. Frequently Asked Questions Q: Will this fit my 2004.5 LLY Duramax?A: Yes. Designed specifically for 2004.5-2005 Chevrolet Silverado 1500HD/2500HD/3500HD and GMC Sierra 1500HD/2500HD/3500HD with the 6.6L LLY Duramax diesel engine. Does NOT fit LB7, LBZ, or LMM engines. Q: Will this trigger a check engine light?A: Yes. Removing the EGR system will set DTCs (P0401-P0409). ECU tuning/delete tuning is required to disable EGR-related codes and prevent limp mode. Hardware only — tuning sold separately. Q: Is EGR delete legal for on-road use?A: EGR delete kits are for OFF-ROAD / COMPETITION USE ONLY. Not legal for on-road vehicles under EPA/CARB regulations. Check your local laws before purchasing. Q: How difficult is installation?A: Intermediate to advanced mechanical skills required. Expect 3-5 hours. Need sockets, wrenches, torque wrench, and ability to drain/refill coolant. Professional installation recommended. No instructions included. Q: Will this improve fuel economy?A: Many users report 1-3 MPG improvement after EGR delete with proper tuning, especially during highway cruising and towing. Results vary by driving habits and tune quality. Related Products High Flow Turbo Intake Elbow for LLY Duramax 3" Downpipe for 2004.5-2010 Duramax Complete EGR Delete Collection Warranty & Support 12-month warranty against manufacturing defects. Contact sales@ifjf.cn with your order number and vehicle details. Order today and eliminate EGR-related performance issues from your LLY Duramax!

Read more less

Product Overview The iFJF EGR Delete Kit for 2011-2019 Ford 6.7L Powerstroke F-250, F-350, F-450, F-550 Super Duty is a complete solution to permanently eliminate the troublesome Exhaust Gas Recirculation (EGR) system. The factory EGR system routes hot, soot-laden exhaust gas back into the intake manifold — causing carbon buildup, reduced engine efficiency, and premature component wear. When the EGR cooler fails (a common issue on the 6.7L Powerstroke), it can leak coolant into the intake, risking catastrophic engine damage. Our kit completely removes the EGR valve(s) and cooler(s), replaces them with precision CNC-machined billet aluminum and stainless steel block-off components, and restores clean, unobstructed airflow to your engine. Every component is engineered for exact OEM fitment — no cutting, welding, or permanent modifications required. Key Features Complete EGR System Removal: Includes all block-off plates, delete pipes, gaskets, and hardware to fully eliminate the EGR valve and cooler from your 6.7L Powerstroke. CNC Billet 6061-T6 Aluminum Construction: Precision-machined from aerospace-grade aluminum — far stronger and more durable than cast alternatives. Black anodized finish for corrosion resistance. 304 Stainless Steel Components: Cooler delete pipes and block-off plates use 304-grade stainless steel where required for maximum heat tolerance and longevity. OEM-Grade Gaskets & Seals: Multi-layer steel (MLS) and high-temperature composite gaskets ensure a perfect, leak-free seal — no exhaust or coolant leaks after installation. Direct Bolt-On Installation: All components use existing mounting points and hardware locations. Average install time: 4-6 hours with basic hand tools. Prevents Coolant Contamination: By removing the EGR cooler from the coolant circuit, you eliminate the risk of coolant leaking into the intake — one of the most common 6.7L catastrophic failures. Compatibility Chart Year Make Model Engine Trim Notes 2011-2023 Ford F-250 Super Duty 6.7L Powerstroke V8 Turbo Diesel All trims (XL, XLT, Lariat, King Ranch, Platinum, Limited) 2011-2023 Ford F-350 Super Duty 6.7L Powerstroke V8 Turbo Diesel All trims; Single & Dual Rear Wheel 2011-2023 Ford F-450 Super Duty 6.7L Powerstroke V8 Turbo Diesel Chassis Cab & Pickup 2011-2023 Ford F-550 Super Duty 6.7L Powerstroke V8 Turbo Diesel Chassis Cab Specifications Specification Detail Material CNC Billet 6061-T6 Aluminum, 304 Stainless Steel, High-Temp MLS Gaskets Finish Black Anodized (Aluminum); Natural (Stainless Steel) Fitment Type Direct Bolt-On — No Modification Required Estimated Install Time 4-6 Hours (Professional); 6-8 Hours (DIY) Includes Hardware Yes — Complete Grade 10.9 bolt/washer/nut kit included Includes Gaskets Yes — MLS & high-temp composite gaskets Warranty 1-Year Limited Warranty Why Choose iFJF? Precision Engineering: Every component is reverse-engineered from OEM dimensions for guaranteed fit. No "universal fit" guesswork. Proven Materials: We use 6061-T6 billet aluminum and 304 stainless steel — not cheap cast pot metal that cracks under heat cycling. Complete Kit: Everything you need in one box. No extra parts to source, no trips to the hardware store. US-Based Support: Our diesel experts are available to answer installation questions. We actually know these trucks. Frequently Asked Questions Q: Will this kit fit my 2011 Ford F-250 6.7L Powerstroke?A: Yes. This kit is specifically designed for 2011-2019 Ford Super Duty trucks equipped with the 6.7L Powerstroke V8 turbo diesel engine, including F-250, F-350, F-450, and F-550 models. Q: Does installing an EGR delete require tuning?A: Yes — removing the EGR system will trigger a check engine light (CEL) unless the ECU is tuned to disable EGR-related DTCs. A custom tuner or EFI Live-compatible device is required. This kit includes the mechanical components only. Q: Will this void my factory warranty?A: Modifying the emissions system may affect your factory powertrain warranty coverage. We recommend consulting your dealer or warranty provider before installation. This product is intended for off-road/competition use. Q: How difficult is the installation?A: The installation is rated moderate to advanced. You'll need basic hand tools (socket set, wrenches, torque wrench), and mechanical experience with diesel engines is strongly recommended. Professional installation typically takes 4-6 hours. Q: What symptoms tell me my EGR cooler is failing?A: Common signs include: white smoke from the exhaust (coolant burning), unexplained coolant loss, coolant in the oil (milky oil appearance), rough idle, and P0401/P0402 error codes. If you notice these, your EGR cooler may already be leaking — immediate replacement or deletion is recommended. Q: Can I still pass emissions testing after installing this kit?A: This kit is designed for off-road and competition use only. Removing emissions equipment is not compliant with EPA/CARB regulations for on-road vehicles. Check your local and state regulations before purchase. Q: What other maintenance should I consider while installing this kit?A: While the intake is accessible, it's a great opportunity to clean the intake manifold, inspect turbo piping, and consider upgrading to a coolant filtration system. Check out our other 6.7L Powerstroke products for complete engine protection. Q: What's the difference between the EGR valve delete and EGR cooler delete?A: The valve delete blocks exhaust gases from entering the intake at the EGR valve port. The cooler delete removes the EGR cooler entirely from the coolant circuit — this is critical because a failed cooler can leak coolant into the intake and cause hydrolock. Our kit includes both. California Proposition 65 Warning: This product is intended for off-road/competition use only. Not CARB-compliant. Check local regulations before purchase.

Read more less

Product Overview The iFJF EGR Delete Kit for 2011-2023 Ford 6.7L Powerstroke F-250, F-350, F-450, F-550 Super Duty is a complete solution to permanently eliminate the troublesome Exhaust Gas Recirculation (EGR) system. The factory EGR system routes hot, soot-laden exhaust gas back into the intake manifold — causing carbon buildup, reduced engine efficiency, and premature component wear. When the EGR cooler fails (a common issue on the 6.7L Powerstroke), it can leak coolant into the intake, risking catastrophic engine damage. Our kit completely removes the EGR valve(s) and cooler(s), replaces them with precision CNC-machined billet aluminum and stainless steel block-off components, and restores clean, unobstructed airflow to your engine. Every component is engineered for exact OEM fitment — no cutting, welding, or permanent modifications required. Key Features Complete EGR System Removal: Includes all block-off plates, delete pipes, gaskets, and hardware to fully eliminate the EGR valve and cooler from your 6.7L Powerstroke. CNC Billet 6061-T6 Aluminum Construction: Precision-machined from aerospace-grade aluminum — far stronger and more durable than cast alternatives. Black anodized finish for corrosion resistance. 304 Stainless Steel Components: Cooler delete pipes and block-off plates use 304-grade stainless steel where required for maximum heat tolerance and longevity. OEM-Grade Gaskets & Seals: Multi-layer steel (MLS) and high-temperature composite gaskets ensure a perfect, leak-free seal — no exhaust or coolant leaks after installation. Direct Bolt-On Installation: All components use existing mounting points and hardware locations. Average install time: 4-6 hours with basic hand tools. Prevents Coolant Contamination: By removing the EGR cooler from the coolant circuit, you eliminate the risk of coolant leaking into the intake — one of the most common 6.7L catastrophic failures. Compatibility Chart Year Make Model Engine Trim Notes 2011-2023 Ford F-250 Super Duty 6.7L Powerstroke V8 Turbo Diesel All trims (XL, XLT, Lariat, King Ranch, Platinum, Limited) 2011-2023 Ford F-350 Super Duty 6.7L Powerstroke V8 Turbo Diesel All trims; Single & Dual Rear Wheel 2011-2023 Ford F-450 Super Duty 6.7L Powerstroke V8 Turbo Diesel Chassis Cab & Pickup 2011-2023 Ford F-550 Super Duty 6.7L Powerstroke V8 Turbo Diesel Chassis Cab Specifications Specification Detail Material CNC Billet 6061-T6 Aluminum, 304 Stainless Steel, High-Temp MLS Gaskets Finish Black Anodized (Aluminum); Natural (Stainless Steel) Fitment Type Direct Bolt-On — No Modification Required Estimated Install Time 4-6 Hours (Professional); 6-8 Hours (DIY) Includes Hardware Yes — Complete Grade 10.9 bolt/washer/nut kit included Includes Gaskets Yes — MLS & high-temp composite gaskets Warranty 1-Year Limited Warranty Why Choose iFJF? Precision Engineering: Every component is reverse-engineered from OEM dimensions for guaranteed fit. No "universal fit" guesswork. Proven Materials: We use 6061-T6 billet aluminum and 304 stainless steel — not cheap cast pot metal that cracks under heat cycling. Complete Kit: Everything you need in one box. No extra parts to source, no trips to the hardware store. US-Based Support: Our diesel experts are available to answer installation questions. We actually know these trucks. Frequently Asked Questions Q: Will this kit fit my 2011 Ford F-250 6.7L Powerstroke?A: Yes. This kit is specifically designed for 2011-2023 Ford Super Duty trucks equipped with the 6.7L Powerstroke V8 turbo diesel engine, including F-250, F-350, F-450, and F-550 models. Q: Does installing an EGR delete require tuning?A: Yes — removing the EGR system will trigger a check engine light (CEL) unless the ECU is tuned to disable EGR-related DTCs. A custom tuner or EFI Live-compatible device is required. This kit includes the mechanical components only. Q: Will this void my factory warranty?A: Modifying the emissions system may affect your factory powertrain warranty coverage. We recommend consulting your dealer or warranty provider before installation. This product is intended for off-road/competition use. Q: How difficult is the installation?A: The installation is rated moderate to advanced. You'll need basic hand tools (socket set, wrenches, torque wrench), and mechanical experience with diesel engines is strongly recommended. Professional installation typically takes 4-6 hours. Q: What symptoms tell me my EGR cooler is failing?A: Common signs include: white smoke from the exhaust (coolant burning), unexplained coolant loss, coolant in the oil (milky oil appearance), rough idle, and P0401/P0402 error codes. If you notice these, your EGR cooler may already be leaking — immediate replacement or deletion is recommended. Q: Can I still pass emissions testing after installing this kit?A: This kit is designed for off-road and competition use only. Removing emissions equipment is not compliant with EPA/CARB regulations for on-road vehicles. Check your local and state regulations before purchase. Q: What other maintenance should I consider while installing this kit?A: While the intake is accessible, it's a great opportunity to clean the intake manifold, inspect turbo piping, and consider upgrading to a coolant filtration system. Check out our other 6.7L Powerstroke products for complete engine protection. Q: What's the difference between the EGR valve delete and EGR cooler delete?A: The valve delete blocks exhaust gases from entering the intake at the EGR valve port. The cooler delete removes the EGR cooler entirely from the coolant circuit — this is critical because a failed cooler can leak coolant into the intake and cause hydrolock. Our kit includes both. California Proposition 65 Warning: This product is intended for off-road/competition use only. Not CARB-compliant. Check local regulations before purchase.

Read more less

Product Overview The iFJF EGR Delete Kit for 2011-2023 Ford 6.7L Powerstroke F-250, F-350, F-450, F-550 Super Duty is a complete solution to permanently eliminate the troublesome Exhaust Gas Recirculation (EGR) system. The factory EGR system routes hot, soot-laden exhaust gas back into the intake manifold — causing carbon buildup, reduced engine efficiency, and premature component wear. When the EGR cooler fails (a common issue on the 6.7L Powerstroke), it can leak coolant into the intake, risking catastrophic engine damage. Our kit completely removes the EGR valve(s) and cooler(s), replaces them with precision CNC-machined billet aluminum and stainless steel block-off components, and restores clean, unobstructed airflow to your engine. Every component is engineered for exact OEM fitment — no cutting, welding, or permanent modifications required. Key Features Complete EGR System Removal: Includes all block-off plates, delete pipes, gaskets, and hardware to fully eliminate the EGR valve and cooler from your 6.7L Powerstroke. CNC Billet 6061-T6 Aluminum Construction: Precision-machined from aerospace-grade aluminum — far stronger and more durable than cast alternatives. Black anodized finish for corrosion resistance. 304 Stainless Steel Components: Cooler delete pipes and block-off plates use 304-grade stainless steel where required for maximum heat tolerance and longevity. OEM-Grade Gaskets & Seals: Multi-layer steel (MLS) and high-temperature composite gaskets ensure a perfect, leak-free seal — no exhaust or coolant leaks after installation. Direct Bolt-On Installation: All components use existing mounting points and hardware locations. Average install time: 4-6 hours with basic hand tools. Prevents Coolant Contamination: By removing the EGR cooler from the coolant circuit, you eliminate the risk of coolant leaking into the intake — one of the most common 6.7L catastrophic failures. Compatibility Chart Year Make Model Engine Trim Notes 2011-2023 Ford F-250 Super Duty 6.7L Powerstroke V8 Turbo Diesel All trims (XL, XLT, Lariat, King Ranch, Platinum, Limited) 2011-2023 Ford F-350 Super Duty 6.7L Powerstroke V8 Turbo Diesel All trims; Single & Dual Rear Wheel 2011-2023 Ford F-450 Super Duty 6.7L Powerstroke V8 Turbo Diesel Chassis Cab & Pickup 2011-2023 Ford F-550 Super Duty 6.7L Powerstroke V8 Turbo Diesel Chassis Cab Specifications Specification Detail Material CNC Billet 6061-T6 Aluminum, 304 Stainless Steel, High-Temp MLS Gaskets Finish Black Anodized (Aluminum); Natural (Stainless Steel) Fitment Type Direct Bolt-On — No Modification Required Estimated Install Time 4-6 Hours (Professional); 6-8 Hours (DIY) Includes Hardware Yes — Complete Grade 10.9 bolt/washer/nut kit included Includes Gaskets Yes — MLS & high-temp composite gaskets Warranty 1-Year Limited Warranty Why Choose iFJF? Precision Engineering: Every component is reverse-engineered from OEM dimensions for guaranteed fit. No "universal fit" guesswork. Proven Materials: We use 6061-T6 billet aluminum and 304 stainless steel — not cheap cast pot metal that cracks under heat cycling. Complete Kit: Everything you need in one box. No extra parts to source, no trips to the hardware store. US-Based Support: Our diesel experts are available to answer installation questions. We actually know these trucks. Frequently Asked Questions Q: Will this kit fit my 2011 Ford F-250 6.7L Powerstroke?A: Yes. This kit is specifically designed for 2011-2023 Ford Super Duty trucks equipped with the 6.7L Powerstroke V8 turbo diesel engine, including F-250, F-350, F-450, and F-550 models. Q: Does installing an EGR delete require tuning?A: Yes — removing the EGR system will trigger a check engine light (CEL) unless the ECU is tuned to disable EGR-related DTCs. A custom tuner or EFI Live-compatible device is required. This kit includes the mechanical components only. Q: Will this void my factory warranty?A: Modifying the emissions system may affect your factory powertrain warranty coverage. We recommend consulting your dealer or warranty provider before installation. This product is intended for off-road/competition use. Q: How difficult is the installation?A: The installation is rated moderate to advanced. You'll need basic hand tools (socket set, wrenches, torque wrench), and mechanical experience with diesel engines is strongly recommended. Professional installation typically takes 4-6 hours. Q: What symptoms tell me my EGR cooler is failing?A: Common signs include: white smoke from the exhaust (coolant burning), unexplained coolant loss, coolant in the oil (milky oil appearance), rough idle, and P0401/P0402 error codes. If you notice these, your EGR cooler may already be leaking — immediate replacement or deletion is recommended. Q: Can I still pass emissions testing after installing this kit?A: This kit is designed for off-road and competition use only. Removing emissions equipment is not compliant with EPA/CARB regulations for on-road vehicles. Check your local and state regulations before purchase. Q: What other maintenance should I consider while installing this kit?A: While the intake is accessible, it's a great opportunity to clean the intake manifold, inspect turbo piping, and consider upgrading to a coolant filtration system. Check out our other 6.7L Powerstroke products for complete engine protection. Q: What's the difference between the EGR valve delete and EGR cooler delete?A: The valve delete blocks exhaust gases from entering the intake at the EGR valve port. The cooler delete removes the EGR cooler entirely from the coolant circuit — this is critical because a failed cooler can leak coolant into the intake and cause hydrolock. Our kit includes both. California Proposition 65 Warning: This product is intended for off-road/competition use only. Not CARB-compliant. Check local regulations before purchase.

Read more less

Product Overview Solve two of the 6.4L Powerstroke's most persistent problems in one installation with the iFJF EGR Delete Plates & Bypass Exhaust Up-Pipes Kit. The factory EGR system on Ford's Navistar-built 6.4L is notorious for EGR cooler rupture (sending coolant into the intake), valve sticking, and carbon packing in the intake manifold. Simultaneously, the OEM up-pipes are prone to cracking at the bellows and flange welds. This kit eliminates the EGR system entirely while upgrading to heavy-duty bypass up-pipes — a complete reliability transformation for your 2008-2010 Super Duty. ⚠️ OFF-ROAD / COMPETITION USE ONLY: This product is intended for off-road, racing, and competition vehicles only. Removing emissions equipment from on-highway vehicles violates the Clean Air Act. Check local, state, and federal regulations before installation. Key Features Complete EGR System Delete: Includes all block-off plates, gaskets, and hardware to fully remove both EGR valves and EGR coolers from the 6.4L Powerstroke engine. Bypass Exhaust Up-Pipes: Heavy-duty T304 stainless up-pipes route exhaust directly to the turbocharger — eliminating the EGR circuit entirely and replacing the crack-prone OEM pipes. Prevents EGR Cooler Failure: Removes the EGR coolers that are infamous for internal rupture, which sends engine coolant directly into the intake manifold and cylinders. Eliminates Carbon Packing: Without EGR soot entering the intake, the intake manifold, intake valves, and swirl ports stay clean — maintaining proper airflow and performance. Lower Coolant Temperatures: Removing the EGR coolers from the cooling circuit reduces overall coolant system heat load, especially during towing. CNC-Machined Block-Off Plates: Precision-cut 6061-T6 aluminum plates with Viton O-ring grooves for leak-free sealing at all EGR port locations. Compatibility Year Make Model Engine 2008-2010 Ford F-250 / F-350 / F-450 / F-550 Super Duty 6.4L Powerstroke V8 Turbo Diesel Specifications Specification Detail Up-Pipe Material T304 Stainless Steel, Mandrel-Bent EGR Plate Material 6061-T6 Billet Aluminum, CNC-Machined O-Ring Type Viton (High-Temperature Rated, up to 400°F) Hardware Grade 8 Bolts, Stainless Steel Fasteners Fitment 2008-2010 Ford 6.4L Powerstroke Super Duty Installation Bolt-on, professional installation recommended (5-8 hours) Why Choose iFJF The 6.4L Powerstroke's EGR system represents one of the most catastrophic failure points in modern diesel history. When an EGR cooler ruptures — and they frequently do on stock trucks — coolant enters the combustion chamber and can hydrolock the engine. iFJF Direct's EGR delete kits are engineered as permanent solutions, not temporary fixes. Our bypass up-pipes are fabricated from 16-gauge T304 stainless with full-penetration TIG welds at every joint, and our block-off plates are CNC-machined to 0.001-inch flatness tolerance for perfect gasket sealing. Frequently Asked Questions Q: Will this kit fit my 2010 F-350 King Ranch 6.4L?A: Yes. This EGR delete kit with bypass up-pipes fits all 2008-2010 Ford Super Duty models with the 6.4L Powerstroke, regardless of trim level or cab configuration. Q: What are the signs of a failing EGR cooler?A: White smoke from the exhaust (especially under load), unexplained coolant loss with no visible external leaks, coolant in the engine oil (milky appearance on dipstick), and rising engine temperature under load are all warning signs. Q: Does this kit include both EGR coolers?A: Yes, the kit includes block-off plates for both the horizontal and vertical EGR coolers found on the 6.4L Powerstroke. All EGR circuit components are addressed. Q: Is a tuner required?A: Yes. An EGR-compatible tuner is required to disable EGR-related diagnostic trouble codes, prevent limp mode, and properly adjust fueling maps for EGR-deleted operation. Q: Can this be installed without removing the cab?A: EGR cooler and up-pipe access on the 6.4L is extremely tight. While cab-off installation is the shop standard, experienced DIY mechanics can complete the job cab-on with patience. Expect 8-12 hours for cab-on installation.

Read more less

Product Overview The iFJF EGR Delete Simulator provides a clean plug-and-play solution for 1986-1995 Ford trucks and SUVs when the EGR system has been removed for off-road applications. Simply connect it to your factory EGR wiring harness — it sends the correct closed-status signal to your ECU, preventing false Check Engine Light (CEL) triggers while keeping the diagnostic system active for real engine problems. Key Features Plug-and-Play Installation — OEM locking connector plugs directly into the factory EGR valve wiring harness. No cutting, splicing, or ECU tuning required. Installs in under 5 minutes. Keeps CEL Functional for Real Problems — Unlike cheap resistor mods, this simulator only suppresses the EGR-specific code (33/332). Your Check Engine Light stays available for all other diagnostic trouble codes — you won't miss a real engine problem. OEM-Grade Locking Connector — Factory-style locking tab ensures a secure, vibration-resistant connection even on rough terrain. No zip-tie-only solutions that work loose. Wide Compatibility — Covers the entire 1986-1995 Ford F-Series, Bronco, and Mustang lineup: 2.8L V6, 4.9L I6, 5.0L V8, 5.8L V8, and 7.5L V8 engines. Built for Off-Road Durability — Sealed and potted housing withstands mud, water, engine heat, and vibration. Battle-tested in desert racing and trail rig applications. Compatibility Make Model Years Engine Ford F-150 1986-1995 2.8L V6 / 4.9L I6 / 5.0L V8 / 5.8L V8 Ford F-250 1986-1995 4.9L I6 / 5.0L V8 / 5.8L V8 / 7.5L V8 Ford F-350 1986-1995 4.9L I6 / 5.0L V8 / 5.8L V8 / 7.5L V8 Ford Bronco 1986-1995 4.9L I6 / 5.0L V8 / 5.8L V8 Ford Mustang 1986-1993 2.8L V6 / 5.0L V8 Specifications Specification Detail Part Number IFJF-FORD-EGR-SIM Connector Type OEM Ford EGR position sensor (3-pin) Housing Material High-temperature ABS plastic Sealing Fully potted — waterproof & vibration-proof Installation Time Under 5 minutes (plug-and-play) Diagnostic Codes Suppresses 33 / 332 (EGR inoperative) Application Off-road / race track use only Why Choose iFJF? We manufacture our own EGR simulators with automotive-grade components — not re-badged generic electronics. Every unit is potted and sealed against moisture and vibration. If you're building a trail rig, race truck, or off-road Bronco, this is the same part our shop customers trust. Our Arizona-based support team knows these trucks inside and out. ⚠️ Warning: This device is intended for off-road / race track use only. Federal law prohibits removal or disabling of any emission control device on emission-applicable vehicles. The purchaser bears full responsibility for end-use decisions and all consequential liabilities. Installation Instructions Disconnect the wiring harness from your EGR valve position sensor. Clean the connector if needed (dielectric grease inside is normal — do not remove it). Firmly insert the EGR Delete Simulator into the harness until the locking tab clicks into place. Secure the simulator and harness to a solid mounting point using electrical tape or a zip tie. This prevents vibration-induced connection issues on rough terrain. Start the vehicle. The CEL should remain off. If illuminated, re-check the connection and re-seat the simulator. Complete Your EGR Delete Setup Need the block-off plate too? Our EGR Delete Simulator & Block Off Plate Kit bundles this simulator with a CNC billet aluminum plate that physically seals the EGR port — the complete mechanical + electronic solution in one box. Frequently Asked Questions Q: Will this trigger a Check Engine Light?A: No. The simulator sends the correct closed-position signal to the ECU. You may see stored code 33/332 during a scan, but these codes will NOT illuminate the CEL unless other unrelated codes are present. Q: Does this work on a California-emissions truck?A: This device is designed for off-road and racing applications only. It is not CARB-compliant and is not legal for on-road use in any state. Check your local regulations before installation. Q: Will this pass emissions inspection?A: No. A vehicle with the EGR system physically removed will fail visual and functional emissions testing. This product is intended for vehicles that are never driven on public roads. Q: Does this work on the 7.5L (460) engine?A: Yes. The EGR position sensor connector is the same across all 1986-1995 Ford truck gas engines — 2.8L V6, 4.9L I6, 5.0L V8, 5.8L V8, and 7.5L V8. Q: What's the difference between this simulator and a block-off plate?A: A block-off plate physically seals the EGR port on the intake manifold. This simulator plugs into the wiring harness to prevent the ECU from detecting the missing EGR valve. Most off-road builds use both: the plate for the mechanical side and the simulator for the electrical side. Q: How long does installation take?A: Under 5 minutes. It's a single plug-in connection — no tools required beyond something to secure the harness (zip tie or tape). Q: Do I need an ECU tune or programmer?A: No. This is 100% plug-and-play. The factory ECU accepts the simulator's signal as if the EGR valve were present and closed. No tuning or programming required. Q: What if it doesn't keep my CEL off?A: We offer a 30-day money-back guarantee. Most issues are connector-related — contact our support team first and we'll help troubleshoot. If it still doesn't work, return it for a full refund. 📖 Diesel maintenance schedule: when to replace fuel, oil & air filters →

Read more less