Accessories

Product Overview The iFJF Low Pressure Electric Fuel Pump is a direct replacement for the factory fuel pump on Volvo Penta 4.3L V6, 5.0L V8, and 5.7L V8 marine engines from 1992 through 2006. This pump delivers a consistent 4-7 PSI of fuel pressure to the carburetor — the exact specification these engines require. Whether you're replacing a failed pump, keeping a spare onboard, or doing a complete fuel system refresh, this pump provides reliable marine-grade performance at a fraction of dealer pricing. Key Features Marine-Specific Application: Designed for the unique demands of marine environments — corrosion-resistant housing, sealed electrical connections, and consistent flow characteristics in rough water conditions. Correct Pressure Range: Delivers 4-7 PSI — the target pressure for carbureted Volvo Penta V6 and V8 engines. Too much pressure floods the carb; too little starves the engine at WOT. 12V Universal Fit: Standard two-wire positive/negative connection. Includes mounting bracket and pre-attached fuel line fittings for common 5/16-inch and 3/8-inch marine fuel hose. Replaces OEM 21608511: Direct interchange with Volvo Penta part number 21608511 and equivalent aftermarket pumps. Quiet Operation: Rubber-isolated mounting bracket minimizes vibration transfer to the hull — a common complaint with generic electric pumps. Compatibility Table Year Make Engine Fuel System 1992-2006 Volvo Penta 4.3L V6 (GL, GS, GSi) Carbureted 1992-2006 Volvo Penta 5.0L V8 (GL, Gi) Carbureted 1992-2006 Volvo Penta 5.7L V8 (GS, GSi) Carbureted Specifications Specification Value Part Number (OEM) 21608511 Voltage 12V DC Pressure Range 4-7 PSI Flow Rate 30+ GPH (Free Flow) Inlet/Outlet 5/16-inch or 3/8-inch Hose Barb Polarity Negative Ground Signs Your Fuel Pump Needs Replacement Hard starting — engine cranks but takes excessive time to fire, especially after sitting Stalling under load — engine dies when you throttle up from idle No-start after winter storage — old fuel varnish seizes the pump internals Intermittent fuel delivery — engine surges or cuts out randomly on the water Audible pump failure — no clicking sound from the pump when the ignition is turned on Installation Guide Disconnect the battery before starting. Remove the old pump from its mounting bracket (typically on the port side of the engine near the fuel filter/separator). Transfer the bracket or use the included one. Connect the fuel lines — pay attention to flow direction (arrow on the pump body). Wire the red lead to ignition-switched 12V and the black lead to a clean ground. Prime the system by cycling the ignition 3-4 times before starting. Check all connections for leaks before heading out on the water. Frequently Asked Questions Q: Will this work on a Mercruiser 4.3L?A: While Mercruiser and Volvo Penta use similar GM-based blocks, fuel pump specifications may differ. Verify your Mercruiser's required fuel pressure before purchasing. This pump is specifically spec'd for Volvo Penta applications. Q: Can I use this for fuel injection (EFI/MPI) engines?A: No! EFI systems require 35-60 PSI. This is a low-pressure pump (4-7 PSI) for carbureted engines only. Using it on an EFI engine will result in a no-start condition. Q: Is this Coast Guard compliant for marine use?A: This pump is designed for marine engine compartments and uses sealed, ignition-protected construction. Always verify compliance with your local marine safety regulations. Q: Should I replace the fuel filter at the same time?A: Yes — absolutely. A new pump paired with an old, clogged fuel filter will fail prematurely. Replace the water-separating fuel filter and any inline filters simultaneously. Q: How long do these pumps typically last?A: In marine applications with regular use and clean fuel, expect 5-8 years of reliable service. Ethanol-blended fuels and long storage periods shorten pump life — consider adding a fuel stabilizer for winter layup.

Read more less

Fuel Injector Return Line Kit for 1988-1994 Ford 7.3L IDI Diesel — 7312 Fix fuel leaks and restore proper injector operation on your 1988-1994 Ford 7.3L IDI diesel engine with this complete injector return line installation kit. The IDI engine's return line system uses braided hoses and plastic caps that degrade over time, causing air intrusion, hard starts, and fuel leaks. This comprehensive kit includes everything needed for a complete return line overhaul. Key Features Complete Installation Kit: Includes all return hoses, injector caps, sealing washers, hose clamps, and installation tool — everything for a full system refresh Viton-Equivalent Hose Material: Resistant to diesel fuel, biodiesel blends, and engine heat — won't swell or crack like original hoses Correct Hose Lengths Pre-Cut: Each hose section is cut to the exact length needed for your 7.3L IDI injector layout Includes Installation Tool: Specialized cap removal and installation tool prevents damage to injector nipples during service Stop Air Intrusion: New caps and hoses eliminate the air leaks that cause the IDI's notorious hard-start problems Compatibility Specification Detail Engine 7.3L IDI Diesel (Naturally Aspirated & Turbo) Years 1988, 1989, 1990, 1991, 1992, 1993, 1994 Vehicles F-250, F-350, F-Super Duty, E-Series Vans Kit Includes Hoses, Caps, Clamps, Washers, Tool Why This Kit Matters The Ford 7.3L IDI is legendary for reliability, but its Achilles' heel is the injector return line system. As the original plastic caps and braided hoses age, they develop micro-cracks that allow air into the fuel system. Since the IDI uses a mechanical injection pump that relies on fuel for cooling and lubrication, air intrusion causes hard starting, rough idle, and eventually pump damage. This return line kit addresses the root cause — not just the symptoms. Installation Overview Clean the injector area thoroughly to prevent debris from entering the fuel system Remove old return line caps using the included tool — avoid prying with screwdrivers Remove old hoses and discard all old clamps Install new sealing washers on each injector nipple Press new caps onto each injector using the installation tool Connect pre-cut hoses between caps following the correct routing pattern Secure each hose end with new clamps Prime the fuel system and check for leaks before starting Frequently Asked Questions Q: My 7.3L IDI is hard to start when it sits overnight — will this fix it?A: Very likely yes. The most common cause of hard cold starts on the IDI is air intrusion through degraded return line caps and hoses. This kit replaces every component of the return system. Q: Does this kit include the injector O-rings?A: This kit focuses on the return line system (caps, hoses, clamps, washers). Injector body O-rings are sold separately or included in injector seal kits. Q: Will this work on the 6.9L IDI (1983-1987)?A: This kit is configured for the 7.3L IDI (1988-1994). The 6.9L uses a different injector and cap configuration. Please verify fitment before ordering. Q: Do I need any special tools besides what's included?A: Basic hand tools (socket set, pliers) are sufficient. The kit includes the specialized cap installation tool. Having a fuel system primer is helpful for bleeding after installation. 🔗 Explore More from iFJF Find the right part for your vehicle or equipment: Browse All Products Fuel Filters Collection Auto Accessories

Read more less

Product Overview The iFJF Fuel Filter Heater Element (9J294) is a direct replacement for Ford part F2TZ-9J294-A, designed for the 6.9L and 7.3L IDI diesel fuel filter housing from 1983-1994. This heater element warms diesel fuel during cold starts to prevent fuel gelling and ensure smooth engine operation in winter conditions. Ideal for replacing a failed heater without buying the entire housing assembly. Key Features Heater Element Only: Replace just the failed heater element — no need to purchase the entire housing assembly. Direct plug-and-play replacement for F2TZ-9J294-A. Cold-Start Performance: Heats diesel fuel during cold weather starts to prevent wax crystal formation (gelling) and ensure fuel flows freely through the filter. IDI Diesel Coverage: Fits all 1983-1994 6.9L and 7.3L IDI naturally aspirated diesel engines — F150 through F350, Super Duty, and Econoline vans. Electrical Connector Compatible: Factory-style electrical connector plugs directly into the existing wiring harness — no splicing or modifications needed. Corrosion-Resistant Design: Built with corrosion-resistant materials to withstand diesel fuel exposure and under-hood environmental conditions. Specifications Specification Detail Part Number FJ-FORD04-01 OEM Reference F2TZ-9J294-A, E8TZ-9B249-A (Heater Element Only) Engine 6.9L IDI / 7.3L IDI (Naturally Aspirated) Function Diesel Fuel Pre-Heating for Cold Starts Fits 1983-1994 F150 F250 F350 Super Duty E150 E250 E350 F59 Note For naturally aspirated IDI only — not Powerstroke Warranty 12-Month Warranty Why Choose iFJF? A failed heater element means hard cold starts, rough idle when cold, and potential fuel gelling in freezing temperatures. If your IDI diesel cranks but struggles to fire on cold mornings, the heater element is a likely culprit — especially on trucks 30+ years old. Our replacement restores proper cold-start performance without replacing the entire housing. Frequently Asked Questions Q: Will this fit my 1989 F350 7.3L IDI?A: Yes. Direct replacement for the heater element in all 1983-1994 6.9L and 7.3L IDI fuel filter housings. Q: How do I know if my heater element is bad?A: Symptoms: hard cold starts, rough idle when cold, no voltage at the heater connector, or visible corrosion/burn marks on the element. Q: Can I install this without replacing the housing?A: Yes. This is the heater element only — it replaces the existing element in your current housing. No need to replace the entire assembly if only the heater has failed. Q: Does this fit the 7.3L Powerstroke?A: No. This is for the older IDI (Indirect Injection) diesel only — not the 1994.5+ Powerstroke. Q: Installation difficulty?A: Simple replacement. Remove the old element from the housing, install the new one, connect the wiring. Budget 15-30 minutes. Q: Do I need this for warm climates?A: Even in warm climates, the heater aids cold-start enrichment. If your truck starts hard when cold regardless of ambient temperature, the heater may still be the issue.

Read more less

Product Overview The iFJF Complete Fuel Filter Housing Kit is the all-in-one solution for rebuilding the fuel filter assembly on 1983-1994 Ford 6.9L and 7.3L IDI diesel engines. This comprehensive kit includes the housing header (F2TZ-9B249-A), heater element (F2TZ-9J294-A), and the bottom lower cap — everything needed to completely refresh your IDI fuel filtration system in one purchase. Key Features All-in-One Complete Kit: Includes housing header, heater element, and bottom lower cap — the three key components of the IDI fuel filter assembly in one box. Full OEM Compatibility: Replaces Ford F2TZ-9B249-A (header), F2TZ-9J294-A (heater), and E8TZ-9B249-A. Interchangeable with factory parts. 1983-1994 IDI Coverage: Fits all 6.9L and 7.3L IDI naturally aspirated engines — F150 through F350, Super Duty, Econoline vans, and F59 chassis. Corrosion-Resistant Aluminum: Upgraded aluminum construction resists rust and diesel fuel corrosion far better than the original steel components. Important Fitment Note: The F2TZ-9J294-A heater element is designed for naturally aspirated IDI engines. Not compatible with 1993 F250 7.3L turbo diesel (newer model). Verify your engine type before ordering. Specifications Specification Detail Part Number FJ-FORD04-ZH3 OEM Reference F2TZ-9B249-A, F2TZ-9J294-A, E8TZ-9B249-A Engine 6.9L IDI / 7.3L IDI (Naturally Aspirated Only) Material Aluminum Housing, Metal Heater Element Includes Housing Header, Heater Element 9J294, Bottom Lower Cap Fits F150 F250 F350 Super Duty E150 E250 E350 F59 1983-1994 Note Not for 1993+ 7.3L Factory Turbo Diesel Warranty 12-Month Warranty Why Choose iFJF? The IDI fuel filter assembly is one of the most failure-prone components on these aging diesel trucks. Corrosion, cracked housings, failed heater elements, and leaking caps all introduce air into the fuel system — causing hard starts, stalling, and power loss. Our complete kit replaces all three problem components at once for true peace of mind. Frequently Asked Questions Q: What does this complete kit include?A: The housing header, heater element (F2TZ-9J294-A), and the bottom lower cap — all three key components of the fuel filter assembly. Q: Will this fit my 1990 F350 7.3L IDI?A: Yes. Direct fit for all 1988-1994 7.3L IDI naturally aspirated diesel engines. Q: Why does it not fit the 1993 F250 7.3L Turbo?A: The factory turbo IDI (introduced 1993) used a different fuel filter configuration in some models. This kit is for naturally aspirated IDI engines. If you have a factory turbo, verify your filter base before ordering. Q: Is this a complete fuel filter replacement?A: This kit replaces the housing assembly — not the filter element itself. The fuel filter cartridge is sold separately and screws into this housing. Q: What are the symptoms that I need this kit?A: Fuel leaks at the filter assembly, air in fuel lines (engine sputters/stalls), diesel smell under hood, hard cold starts, and a non-functional fuel heater. Q: Installation difficulty?A: Intermediate. Requires basic hand tools and fuel line wrenches. Purge the fuel system after installation. Budget 1-2 hours. Q: How is this different from the FJ-FORD04-ZH1?A: The ZH3 includes the bottom lower cap in addition to the header and heater — making it the most complete kit available.

Read more less

Product Overview The iFJF Fuel Filter Housing Header is a direct replacement for the factory fuel filter header on 1983-1994 Ford 6.9L and 7.3L IDI diesel engines. Replaces Ford OEM part F2TZ-9B249-A (interchangeable with E8TZ-9B249-A). This is the housing header only — ideal if your heater element is still functional and you only need to replace a leaking or corroded housing. Includes cap and connector. Key Features Housing Header Only: For when your heater element is still working — replace just the leaking or corroded housing header and save money versus buying the full assembly. Direct OEM Fit: Replaces Ford F2TZ-9B249-A. Interchangeable with E8TZ-9B249-A. Same bolt pattern and fuel line connections as factory. 1983-1994 IDI Coverage: Fits all 6.9L (1983-1987) and 7.3L (1988-1994) IDI naturally aspirated diesel engines — F150 through F350, Super Duty, and Econoline vans. Aluminum Construction: Corrosion-resistant aluminum housing resists rust and diesel fuel degradation — a major upgrade over the factory steel unit. Includes Cap & Connector: Complete header assembly with cap and wiring connector — ready to bolt on and connect to your existing heater element. Specifications Specification Detail Part Number FJ-FORD04-SI OEM Reference F2TZ-9B249-A, E8TZ-9B249-A Engine 6.9L IDI (1983-1987) / 7.3L IDI (1988-1994) Material Aluminum Includes Housing Header, Cap, Connector (heater NOT included) Fits F150 F250 F350 Super Duty E150 E250 E350 F59 Warranty 12-Month Warranty Why Choose iFJF? After 30+ years, the factory fuel filter housing on IDI diesels often corrodes and leaks, introducing air into the fuel system and causing hard starts. If your heater element is still working, this housing-only option saves you money while solving the leak. For a complete rebuild including heater, see our FJ-FORD04-ZH1 kit. Frequently Asked Questions Q: Will this fit my 1986 F250 6.9L IDI?A: Yes. Direct fit for all 1983-1987 6.9L and 1988-1994 7.3L IDI naturally aspirated diesel engines. Q: Does this include the heater element?A: No. This is the housing header only (with cap and connector). If you need the heater element too, see our complete kit FJ-FORD04-ZH1 or separate heater FJ-FORD04-01. Q: Does this fit the Powerstroke?A: No. This is for the IDI diesel only. The 7.3L Powerstroke uses a different fuel filter system. Q: What are symptoms of a bad housing?A: Fuel leaking at the filter base, air intrusion (hard starting/stalling), diesel odor under hood. Q: Installation difficulty?A: Intermediate DIY. Basic hand tools and fuel line wrenches needed. Budget 1-2 hours with system bleeding.

Read more less

Product Overview The iFJF Fuel Filter Housing Header with Heater Element is a direct replacement for the factory fuel filter assembly on 1983-1994 Ford 6.9L and 7.3L IDI diesel engines. This complete kit includes the housing header (F2TZ-9B249-A) and heater element (F2TZ-9J294-A) — the two most failure-prone components of the OEM fuel filter system. Manufactured from corrosion-resistant aluminum, this assembly restores proper fuel filtration and cold-start performance. Key Features Complete Header + Heater Kit: Includes both the fuel filter housing header and the heater element — everything needed for a full rebuild of your IDI fuel filter assembly. Direct OEM Replacement: Replaces Ford F2TZ-9B249-A (housing header) and F2TZ-9J294-A (heater element). Interchangeable with E8TZ-9B249-A. 1983-1994 IDI Diesel Fitment: Compatible with all 6.9L (1983-1987) and 7.3L (1988-1994) IDI naturally aspirated diesel engines — F-Series trucks, Super Duty, and Econoline vans. Corrosion-Resistant Construction: Built from high-quality aluminum that resists rust and diesel fuel corrosion far better than the factory steel unit. Cold-Start Heater Element: Integrated fuel heater element warms diesel fuel during cold starts — critical for winter operation and preventing fuel gelling. Specifications Specification Detail Part Number FJ-FORD04-ZH1 OEM Reference F2TZ-9B249-A, F2TZ-9J294-A, E8TZ-9B249-A Engine 6.9L IDI (1983-1987) / 7.3L IDI (1988-1994) Material Aluminum Housing with Heating Element Includes Housing Header, Heater Element 9J294 Fits F150 F250 F350 Super Duty E150 E250 E350 F59 Warranty 12-Month Warranty Why Choose iFJF? The factory fuel filter housing on the IDI diesel is prone to corrosion, leaking, and heater element failure — especially after 30+ years of service. A leaking housing introduces air into the fuel system, causing hard starts, rough idle, and power loss. Our iFJF replacement kit solves both the housing and heater element in one purchase at a competitive price. Frequently Asked Questions Q: Will this fit my 1991 F250 7.3L IDI?A: Yes. Direct fit for all 1988-1994 7.3L IDI and 1983-1987 6.9L IDI naturally aspirated diesel engines. Q: Does this fit the 7.3L Powerstroke (1994.5+)?A: No. This is for the IDI (Indirect Injection) diesel only — not the 7.3L Powerstroke (direct injection) introduced in mid-1994. The Powerstroke uses a completely different fuel filter system. Q: Does this include the heater element?A: Yes. This complete kit includes both the housing header (F2TZ-9B249-A) and the heater element (F2TZ-9J294-A). Q: What are signs of a failing fuel filter housing?A: Fuel leaks at the filter housing, air in fuel lines (hard starting/stalling), diesel smell under the hood, and cold-start difficulty if the heater element fails. Q: Is this for turbo or non-turbo IDI?A: This fits naturally aspirated IDI engines. For factory turbo IDI (1993-1994), verify the filter base — some turbo models used a different configuration. Q: How difficult is the installation?A: Intermediate DIY. Requires basic hand tools and fuel line wrenches. Purge the fuel system after installation by cycling the key. Budget 1-2 hours. Q: Does this include the fuel filter itself?A: No. The fuel filter element is sold separately. This kit includes the housing header and heater element — the assembly that the filter screws onto.

Read more less

Product Overview The 904-210 F81Z-9J294-AA Diesel Fuel Filter Bowl Heating Heater 015321 Warm-Up Element for 1994-2004 International Trucks w/7.3L Diesel Engine is a premium-quality replacement part engineered to meet or exceed OEM specifications. Designed for durability, reliability, and perfect fitment, this iFJF product delivers professional-grade performance at an affordable price. Key Features High-Efficiency Filtration: Removes water and contaminants for maximum engine protection. Corrosion-Resistant: Built with materials that withstand diesel fuel and marine environments. Extended Service Life: High dirt-holding capacity extends service intervals. Protects Injection System: Clean fuel delivery prevents injector wear and extends engine life. Easy Replacement: Designed for quick filter changes with minimal downtime. Compatibility & Fitment Designed as a direct replacement for the following applications. ⚠️ Always verify your equipment model, year, and specifications before ordering. Make Model Year Notes Universal Various — See product title for fitment Technical Specifications Specification Detail Brand iFJF Condition New Fitment Type Direct Replacement Part Number 904-210, F81Z-9J294, 015321 Type Fuel Water Separator Micron Rating 30 Micron Why Choose iFJF? OEM-Grade Quality: Manufactured to strict tolerance standards for reliable performance Rigorous Testing: Every product undergoes quality inspection before shipping Fast Shipping: Orders processed within 1-2 business days from our US warehouses Expert Support: Technical assistance available for installation and troubleshooting Hassle-Free Returns: 30-day return policy for your peace of mind Frequently Asked Questions Q: How often should I replace this filter?A: For diesel applications, replace every 10,000-15,000 miles or annually. For marine, replace every 100 hours or seasonally. Q: How do I drain water from the separator?A: Locate the drain valve at the bottom of the filter housing. Place a container underneath and slowly open the valve until clean fuel appears. Q: Will this filter work with biodiesel?A: Compatible with diesel fuel blends up to B20 (20% biodiesel). Higher concentrations may require more frequent filter changes. Q: What micron rating does this filter have?A: This filter provides 30-micron filtration, effectively removing water and particulate contaminants. Q: Do I need to prime after changing the filter?A: Yes, prime the fuel system after replacement. Most housings have a manual primer pump. Crank engine in short bursts until it starts smoothly.

Read more less

Product Overview Get double the value with the iFJF 57180 Oil Filter Stopple Tool 2-Pack. This convenient two-pack gives you a spare for your service truck, shop, or as a gift for a fellow RAM Cummins owner. Each tool is precision-machined to seal the oil filter housing drain during oil changes on Dodge RAM 2500 and 3500 trucks with 5.9L and 6.7L Cummins diesel engines (2013-2018). Whether you're a professional diesel mechanic managing a fleet or a dedicated DIY owner, having two of these essential tools means you're always ready. Keep one in the garage and one in the truck for roadside oil changes, or share with your shop crew. Key Features Value 2-Pack: Two identical tools — keep a spare or share with a friend Precision Machined: CNC aluminum alloy construction ensures an exact OEM fit Leak-Free Seal: Stops oil flow from filter housing during filter changes — no more mess Corrosion Resistant: Anodized finish protects against oil, fuel, and road chemicals Diesel Essential: Must-have tool for anyone who changes their own Cummins oil OEM Compatible: Designed to match 05083285AA, MO285 specifications 📋 Compatibility Compatible Vehicles Dodge RAM 2500 5.9L Cummins (2003-2012) Dodge RAM 2500 6.7L Cummins (2007-2018) Dodge RAM 3500 5.9L Cummins (2003-2012) Dodge RAM 3500 6.7L Cummins (2007-2018) 📐 Specifications Specification Value Quantity 2 Pieces Part Number 57180 Material Aluminum alloy, anodized Thread M28 × 1.5 Application Cummins oil filter housing drain plug ❓ Frequently Asked Questions Q: Why buy a 2-pack?A: A 2-pack gives you a backup tool — keep one in your garage toolbox and one in your truck's service kit. It's also great value for professional shops where multiple techs need access. Q: Are both tools identical?A: Yes. Both tools are identical, precision-machined 57180 oil filter stopple plugs that fit all compatible RAM Cummins models. Q: Will these work on my 2016 RAM 2500 6.7L?A: Absolutely. These tools are designed for 2013-2018 RAM 2500/3500 models with the 6.7L Cummins, as well as earlier 5.9L models. Q: How do I use the stopple tool?A: After removing the oil filter cap (36mm socket), thread the stopple tool into the center drain port hand-tight. This seals the drain, allowing you to remove the old filter without oil spilling out. Q: Can I use this with aftermarket oil filters?A: Yes. The tool seals the housing drain port, which is the same regardless of which oil filter brand you use (Mopar, Fleetguard, Wix, etc.). Why Choose iFJF? iFJF delivers quality diesel maintenance tools at unbeatable value. Our 2-pack ensures you always have a clean, efficient oil change. Trusted by diesel owners across North America, iFJF is your go-to source for Cummins maintenance essentials.

Read more less

Product OverviewThe 816296Q2 is a 5/16-inch inline fuel filter designed for Mercury Marine outboard engines from 40HP to 400HP, including 2-stroke, 4-stroke EFI, and Verado supercharged models. This kit includes the 42-micron inline filter, replacement fuel line, and stainless steel hose clamps — everything needed for a complete in-line fuel filter service. Essential maintenance for protecting sensitive fuel injectors from debris.Key Features Complete Service Kit: Includes 42-micron inline filter element, 5/16" marine-grade fuel hose, and stainless steel hose clamps. Everything needed for one fuel filter service. Wide Mercury Compatibility: Fits Mercury 40-400HP outboards — 2-stroke (40-60HP), 4-stroke EFI (75-115HP), and Verado supercharged (150-400HP). 42-Micron Inline Protection: Catches rust, sediment, and debris from fuel tanks and lines before they reach the engine-mounted filter or injectors. Marine-Grade Materials: UV-resistant fuel hose rated for marine applications. Stainless steel clamps resist corrosion in saltwater environments. Meets USCG standards. Easy Inline Installation: Cut the old filter out, insert the new one with directional arrow facing the engine, secure with clamps. 5-minute job. Compatibility Engine Series HP Range Stroke Mercury 2-Stroke 40-60 HP 2-Stroke Mercury EFI 4-Stroke 75-115 HP 4-Stroke EFI Mercury Verado 150-400 HP 4-Stroke Supercharged Specifications Specification Value Part Number 816296Q2 Replaces 35-879885T, 35-816296-4, 879885Q Micron Rating 42 Micron Fuel Line Size 5/16" ID Kit Contents Filter + Fuel Hose + 2 SS Clamps Why Choose iFJFA clogged inline fuel filter causes lean running that can destroy outboard pistons in minutes — especially on Verado supercharged engines. iFJF 816296Q2 kits provide everything for a complete inline filter replacement at a fraction of dealer pricing. Replace annually for reliable outboard performance.Frequently Asked QuestionsQ: Does this kit include fuel line and clamps?A: Yes — complete kit: inline filter, 5/16" marine fuel hose, two stainless steel clamps.Q: Will this fit my Mercury 150HP Verado?A: Yes. Fits all Mercury 40-400HP: 2-stroke, 4-stroke EFI, and Verado supercharged outboards.Q: Where is this filter installed?A: In fuel line between primer bulb and engine. Arrow points toward engine. Secure with provided clamps.Q: Is 42-micron enough?A: Yes — pre-filter stage. Catches larger debris before engine-mounted filter or VST screen.Q: How often should I replace?A: Annually or every 100 hours. Inspect before each outing. Replace immediately if sediment visible.

Read more less

Electric Fuel Pump for 6.0L Powerstroke The SP114 Electric Fuel Pump for F250-F550 Super Duty 6.0L 2003-2007 Expre is a direct bolt-on replacement for the factory fuel pump on Ford 6.0L Powerstroke diesel engines. Provides consistent fuel pressure and flow rate essential for proper injector operation. Prevents hard starts, power loss, and injector damage caused by weak fuel delivery. Key Features Direct OEM Replacement: Drop-in fit for 2003-2007 Ford 6.0L Powerstroke F250-F550 Consistent Fuel Pressure: Maintains 45-65 PSI for proper HEUI injector operation Quiet Operation: Upgraded pump design reduces noise vs factory unit Complete Assembly: Includes pump, mounting bracket, and harness connector Prevents Injector Damage: Proper fuel delivery protects expensive HEUI injectors from failure Compatibility Vehicle Fitment: 2003-2007 Ford F-250/F-350/F-450/F-550 Super Duty 6.0L Powerstroke 2003-2007 Ford Excursion 6.0L Powerstroke 2003-2007 Chevrolet Express/GMC Savana 6.0L gas (verify fitment) Cross References: SP114, E2353, P76687M, Ford 4C3Z-9A317-CA, 4C3Z-9A317-DA Technical Specifications Pump Type Electric In-Line Fuel Pump Operating Pressure 45-65 PSI Flow Rate 40+ GPH at Rated Pressure Voltage 12V DC Inlet/Outlet Standard Quick-Connect Fittings Why Choose iFJF Direct Fast US Shipping: Orders ship from our US warehouse within 1 business day Quality Guaranteed: Every product inspected before shipping Expert Support: Diesel and pool specialists ready to help with fitment questions Trusted by Mechanics: 5,000+ positive reviews from professional technicians and DIYers Frequently Asked Questions Q: What are the symptoms of a failing 6.0L Powerstroke fuel pump?A: Common symptoms include: long crank times before starting, loss of power under load, rough idle, stalling, and diagnostic trouble codes (DTCs) P0087 (low fuel rail pressure) or P2291 (injector control pressure too low). Q: Is this a direct bolt-on replacement?A: Yes, this SP114 pump is a direct bolt-on replacement for the factory HFCM (Horizontal Fuel Conditioning Module) pump. It uses the same mounting bracket, electrical connector, and fuel line fittings. Q: Do I need to replace the filters at the same time?A: We strongly recommend replacing both fuel filters (HFCM frame-mounted filter and engine-mounted secondary filter) when replacing the pump. Contaminated filters can cause the new pump to work harder and fail prematurely. Q: Will this fix my hard-start issue?A: If your hard-start issue is caused by a weak fuel pump (low pressure), yes. However, hard starts on 6.0L Powerstrokes can also be caused by: failing FICM, leaking injector O-rings, HPOP issues, or glow plug problems. Proper diagnosis is recommended. Related Products FD4615 Fuel + FL2016 Oil Filter Combo Fuel Filter Cap 7.3L Powerstroke Fuel Filter 6.5L Diesel

Read more less

311401 Oil Filter & Housing Cap Kit — 2014-2020 Maserati Ghibli, Quattroporte, Levante 3.0L V6 The 311401 Oil Filter and Housing Cap Kit is a complete oil change solution for 2014-2020 Maserati Ghibli, Quattroporte, and Levante vehicles equipped with the 3.0L twin-turbo V6 (F160) engine. This kit includes both the high-efficiency oil filter cartridge element AND the replacement oil filter housing cap — because on these Maserati engines, the plastic OEM cap is notorious for cracking at the torque spec tabs, leading to oil leaks and low oil pressure warnings. Replace both in one job. Key Features Complete Oil Change Kit: Filter cartridge + replacement housing cap in one package — everything you need for a proper oil service. Upgraded Housing Cap: Reinforced construction addresses the weak point of the factory plastic cap that commonly cracks at the 25Nm torque tabs. High-Efficiency Filter Media: Multi-layer synthetic/cellulose blend captures particles down to 20 microns — protecting the F160's twin turbochargers from oil contamination. OEM-Spec Bypass Valve: Internal bypass valve opens at the correct pressure differential — ensures oil flow continues even if the filter is restricted (cold start protection). Pre-Lubed O-Rings: Factory-applied silicone lubrication on all sealing surfaces for proper installation and leak-free operation. Compatibility Year Make Model Engine 2014-2019 Maserati Ghibli 3.0L Twin-Turbo V6 (F160) 2014-2019 Maserati Quattroporte 3.0L Twin-Turbo V6 (F160) 2017-2020 Maserati Levante 3.0L Twin-Turbo V6 (F160) Frequently Asked Questions Q: Why do I need to replace the housing cap too?A: The factory Maserati oil filter housing cap is made of plastic with molded torque tabs. Over time and repeated oil changes, these tabs crack — especially if over-torqued. A cracked cap causes oil leaks, low oil pressure, and potential engine damage. Our replacement cap is reinforced to prevent this common failure. Q: What oil should I use with this filter?A: Maserati recommends 5W-40 full synthetic meeting API SN or ACEA C3 specifications. Brands commonly used include Pennzoil Platinum Euro, Mobil 1 ESP, and Shell Helix Ultra. Capacity: approximately 8.5 quarts with filter change. Q: Can I do this oil change myself or do I need a dealer?A: The F160 V6 oil change is more involved than a typical car due to undertray removal and filter housing access, but it's absolutely DIY-friendly with the right tools. You'll need a 36mm socket for the housing cap, a torque wrench (25Nm), and ramps or a lift. Dealer oil changes on these cars often run $400-500 — DIY saves $250+ per change.Related Guides & Articles📖 Maserati Ghibli Oil Change: DIY Guide — Save $250+ Per Service

Read more less

Product Overview Upgrade your vehicle with this premium fuel tank gas cap, precision-engineered for exact fitment and long-lasting performance. Designed as a direct replacement for CL, CLK, CLS, GLK (2001-2018), this aftermarket component meets or exceeds OEM specifications for durability, reliability, and ease of installation. Whether you're a professional mechanic or a weekend DIYer, this is the cost-effective alternative to dealership pricing. Key Features & Benefits Direct Bolt-On Fit: Precision-manufactured to factory tolerances — no modifications required for installation. Premium-Grade Materials: Constructed from high-strength materials with anti-corrosion treatment for maximum service life in all climates. OEM-Spec Engineering: Manufactured to match or exceed original equipment specifications — guaranteed compatibility and performance. Complete Replacement Kit: Includes all necessary hardware, seals, and gaskets for a complete installation. Quality Tested: Each unit passes multi-point inspection before shipment to ensure dependable, trouble-free operation. Vehicle Compatibility Attribute Specification Compatible Vehicles CL, CLK, CLS, GLK Year Range 2001-2018 Replaces OEM Part # Assembly, 2214700605, Mercedes, Replacement, Tether, cracked iFJF SKU FJ-CAP14-2214-02 Brand iFJF Technical Specifications Specification Detail Product Type Fuel Tank Gas Cap — Aftermarket Replacement Condition Brand New — Never Installed Construction Premium-grade materials — rust, corrosion & heat resistant Installation Type Direct bolt-on replacement — professional installation recommended Warranty 30-day satisfaction guarantee — hassle-free returns Why Choose iFJF Parts? OEM-Grade Quality: Every iFJF component is manufactured to meet or exceed factory specifications — no compromises on materials, tolerances, or durability. Multi-Point QC Inspection: Each unit undergoes rigorous quality testing before leaving our facility, ensuring reliable performance right out of the box. US-Based Inventory: Products ship from US warehouses — no 30-day overseas wait times. Most orders ship within 1-2 business days. Dedicated Support Team: Our automotive specialists are available to answer fitment questions and provide installation guidance. Risk-Free Purchase: 30-day hassle-free return policy — if it doesn't fit or you're not satisfied, we'll make it right. Installation Guidelines Verify Fitment: Check the compatibility table above and compare with your vehicle's year, make, model, and engine before ordering. Compare Parts: Before installation, compare the new part side-by-side with your old unit to confirm identical fitment. Surface Preparation: Clean all mounting surfaces thoroughly to ensure proper seating and seal integrity. Torque Specifications: Use the torque values specified in your vehicle's factory service manual — do not over-tighten. Professional Installation: While DIY-friendly, we recommend professional installation for safety and optimal results. Frequently Asked Questions Q: Will this fit my specific vehicle?A: Please verify using the compatibility table above. Match your vehicle's year, make, model, and engine. If you're still unsure, send us your VIN or vehicle details — we'll confirm compatibility within 24 hours. Q: Is this a genuine OEM part?A: This is a premium aftermarket replacement manufactured to OEM specifications. It delivers equivalent or better quality at a fraction of dealership pricing. Q: What tools do I need for installation?A: Most installations require only basic hand tools. We recommend checking your vehicle's service manual for any specialized tools needed for your specific application. Q: What's included in the package?A: The package includes the fuel tank gas cap and all necessary components as shown in product images. Hardware, seals, and gaskets are included where applicable. Q: How fast is shipping?A: Orders ship from our US warehouses within 1-2 business days. Standard delivery is typically 3-7 business days. Express shipping options are available at checkout. Q: What if it doesn't fit?A: We offer a 30-day hassle-free return policy. If the part doesn't fit or you're unsatisfied for any reason, contact us for a prepaid return label and full refund. 🔗 Related Products & Resources Complete your setup and get the most from your purchase: 📦 Browse All Fuel System 🛒 Shop All iFJF Parts 📖 Read Installation & Maintenance Guides ❓ Ask a Fitment Question 📚 Installation & Maintenance Guides 1965-1967 Mustang 200ci Inline-6 Carburetor Replacement Guide How to Tune an Autolite 1101 Carburetor on Classic Ford

Read more less

Product Overview Keep your Ford Power Stroke running clean with this complete fuel filter kit for 2003-2010 Ford Super Duty trucks. This kit includes both filters needed for a full fuel system service: the HFCM (Horizontal Fuel Conditioning Module) filter on the frame rail AND the engine-mounted secondary filter under the hood. 6.0L and 6.4L Power Stroke fuel injectors operate at extreme pressures and tight tolerances. Contaminated fuel is the #1 cause of injector failure — a $3,000+ repair. Regular fuel filter changes are the cheapest insurance you can buy for your Power Stroke. Key Features Complete 2-Filter Kit — Includes HFCM frame-rail filter + engine-mounted fuel filter OEM-Grade Filtration — Meets Ford spec WSS-M2C942-A for 6.4L and OEM specs for 6.0L Water Separation — HFCM filter includes water-stripping coalescing media Includes O-Rings — All necessary seals for leak-free installation 15,000-Mile Interval — Matches Ford's recommended service schedule Compatibility Year Make Model Engine 2003–2007 Ford F-250 / F-350 / F-450 / F-550 Super Duty 6.0L Power Stroke 2008–2010 Ford F-250 / F-350 / F-450 / F-550 Super Duty 6.4L Power Stroke 2003–2005 Ford Excursion 6.0L Power Stroke 2004–2010 Ford E-350 / E-450 6.0L Power Stroke Cross-Reference Brand HFCM Filter Engine Filter Motorcraft FD-4615 FD-4616 Ford OEM 3C3Z-9N184-CA 4C3Z-9N184-AA Racor PFF-5486 PFF-5487 Why Regular Fuel Filter Changes Matter 6.0L injectors fire at up to 26,000 PSI — any contamination is catastrophic Water in fuel leads to injector tip erosion and internal corrosion A clogged HFCM filter restricts fuel flow, causing low power and hard starting Neglected fuel filters are the #1 misdiagnosis that leads to unnecessary injector replacement Frequently Asked Questions Q: How often should I change both fuel filters?A: Every 15,000 miles or 12 months. If you tow heavy, idle frequently, or use biodiesel, change every 10,000 miles. Always replace both filters together — the HFCM and engine filter work in series. Q: What's the difference between 6.0L and 6.4L fuel filters?A: The frames and fuel systems use different part numbers, but this kit covers BOTH engines. The HFCM filter design is the same; the engine-mounted filter differs between 6.0L (round cartridge) and 6.4L (specific design). Q: Will this fit a 2006 F-350 6.0L?A: Yes — this kit fits ALL 2003-2007 6.0L and 2008-2010 6.4L Super Duty trucks including F-250 through F-550. Q: Does the kit include the water separator drain O-ring?A: Yes, the necessary O-rings for the HFCM filter housing cap and drain plug are included. Installation Tips Remove HFCM filter first (frame rail under driver's door) — have a drain pan ready Clean HFCM housing thoroughly before installing new filter Replace engine-mounted filter second — access from top of engine bay Cycle key ON (not start) 6-8 times for 30 seconds each to prime fuel system Start engine and check for leaks at both filter housings Related Products Cummins FF266 Fuel Filter — For Dodge Ram 6.7L Browse All Diesel Fuel Filters Related Blog Posts Power Stroke 6.0L vs 6.4L: Maintenance Guide

Read more less

Fuel Filter Cap for 1999-2003 Ford 7.3L Powerstroke - F81Z-9G270-BA Precision Fuel Filter Cap — OEM-Spec Fit Replace your worn or cracked fuel filter cap with this precision-engineered replacement for Ford 7.3L Powerstroke. Manufactured to exact OEM tolerances, this cap ensures a leak-proof seal that maintains proper fuel system pressure. Don't risk fuel leaks or air intrusion — a properly sealed filter cap is critical for reliable engine starting and operation. Key Features Leak-Proof Seal — Integrated O-ring groove ensures consistent sealing pressure across full temperature range OEM-Quality Construction — Manufactured to ISO/TS 16949 quality standards with 100% end-of-line testing Direct Fit — Precision-engineered to match OEM dimensions and mounting points — no modifications required Corrosion Resistant — Coated/plated components withstand diesel fuel, road salt, and moisture exposure Validated for Ford — Confirmed fitment across all listed applications Compatibility Make Engine Year Range Model Ford 7.3L Powerstroke 1999-2003 F-250/350/450/550 Super Duty Ford 7.3L Powerstroke 2000-2003 Excursion Always verify fitment using the cross-reference part numbers below or contact our support team. Cross-Reference Part Numbers Brand Part Number Ford F81Z-9G270-BA Motorcraft FD-4596 Alliant 1831193C91 Dorman 904-203 Specifications Specification Value Part Number Fuel Brand iFJF Product Type Fuel Filter Cap Application 7.3L Powerstroke Vehicle Make Ford Material Steel/Plastic Composite Country of Origin China (ISO Certified) Warranty 1 Year / Unlimited Mileage Installation Guide Professional installation is recommended. Always refer to your vehicle or engine service manual for specific torque specifications and priming procedures. Replace all O-rings and seals during filter service — never reuse old seals. Maintenance Schedule Inspect during every filter service for signs of wear, cracking, or corrosion. Replace immediately if any damage is detected. Frequently Asked Questions Q: Is this an OEM or aftermarket fuel filter cap? This is a high-quality aftermarket replacement cap manufactured to exact OEM specifications for 7.3L Powerstroke. It provides the same fit, seal, and durability as the factory cap at a fraction of the dealer price. Q: Does the cap come with a new O-ring? Yes, this fuel filter cap includes a new Viton O-ring pre-installed for a leak-free seal. We recommend replacing the O-ring every time the filter is serviced. Q: What causes a fuel filter cap to fail? Fuel filter caps commonly fail due to over-torquing during installation (which cracks the plastic), UV/heat degradation of the plastic material, or O-ring deterioration causing air leaks. Q: How tight should I torque the fuel filter cap? Typically 25-35 Nm depending on your specific vehicle. Always refer to your service manual for the exact torque specification. Over-tightening is a leading cause of cap failure. Q: Will a bad fuel filter cap cause starting problems? Yes. A cracked or poorly sealed fuel filter cap can allow air into the fuel system, causing hard starts, rough running, and loss of prime — especially after the vehicle sits overnight. Related Products 🔗 Ford Parts & Filters 🔗 All Diesel Fuel Filters | All iFJF Products Related Blog Posts 📖 Complete Guide: When to Replace Your Diesel Fuel Filter 📖 5 Warning Signs Your Fuel Filter Is Clogged 📖 Ford Powerstroke Fuel System Maintenance

Read more less

Premium Diesel Filtration — Engineered for Maximum Protection The 2017-2020 Chevy Silverado/GMC Sierra 2500HD 3500HD 6.6L Billet Aluminu is a critical maintenance component for diesel engine applications. Modern high-pressure common rail fuel systems operate at extreme pressures with micron-level tolerances — even microscopic contaminants can destroy injectors and high-pressure pumps costing thousands in repairs. This premium replacement filter delivers OEM-grade protection with multi-layer filtration media that traps 99.5% of harmful particles including dirt, rust, scale, and water while maintaining unrestricted fuel flow for rated horsepower output under all load conditions. Whether maintaining a Duramax-powered work truck, a Cummins RV generator, marine diesel, or commercial fleet equipment, the quality of your filtration directly determines engine life and reliability. Our filters are manufactured in IATF 16949-certified facilities and undergo rigorous multi-point inspection — burst pressure testing, micron rating verification, and leak testing — before reaching your door. Key Features & Benefits Multi-Layer Filtration: Synthetic-blend media captures 99.5% of contaminants including invisible sub-micron particles, abrasive dust, and emulsified water droplets that destroy injection systems. Heavy-Duty Construction: Reinforced steel canister with corrosion-resistant coating handles extreme pressure pulses from modern HPCR pumps without deformation or fatigue cracking. Precision-Matched Sealing: Nitrile/Viton gasket profile exactly matches OEM specifications — no leaks, no bypass, no installation frustration. Extended Service Life: High dirt-holding capacity extends service intervals without compromising efficiency, reducing total maintenance cost per mile. Pressure-Tested Quality: Every unit undergoes burst, micron, and leak testing. IATF 16949-certified manufacturing ensures consistent quality. Technical Specifications Specification Detail Filter Type Spin-On / Cartridge Diesel Filter Filtration Media Multi-Layer Synthetic/Cellulose Blend Efficiency Beta ≥ 200 (99.5% at Rated Micron) Gasket Material Nitrile Rubber with Anti-Stick Coating Pressure Rating Up to 200 PSI Burst / 150 PSI Operating Service Interval 15,000 Miles or 12 Months (Standard Duty) Frequently Asked Questions Q: Will this filter fit my specific vehicle or equipment?A: Please verify the OEM part number cross-reference and application list in the description. For definitive fitment confirmation, message us your VIN, engine code, or equipment model number and we will confirm compatibility same business day. Q: How often should this filter be replaced?A: For on-road diesel applications, replace every 15,000 miles or annually — whichever comes first. For off-road, marine, generator, or severe-duty applications, replace every 250 operating hours. Always refer to your OEM maintenance schedule. Q: Is this compatible with biodiesel blends?A: Yes, compatible with ULSD and biodiesel blends up to B20. For B20-B100 concentrations, we recommend reducing the change interval by 50% as biodiesel has higher solvent properties. Q: Why choose aftermarket over OEM dealer parts?A: Our filters are manufactured to the same or higher specifications at 40-70% less than dealership pricing. Same IATF 16949 certification, same filtration efficiency — better value with free shipping and returns. Q: What symptoms indicate a clogged or failing filter?A: Hard starting, loss of power under load, fuel pressure warning lights, excessive exhaust smoke, or rough idle. Preventive replacement is always far cheaper than fuel system repairs. Q: What is your warranty and return policy?A: iFJF offers 30-day hassle-free returns and 1-year warranty against manufacturing defects. Wrong part or defective? We ship a replacement or issue a full refund — no restocking fees, ever. Explore More from iFJF Looking for related parts and accessories? Browse our complete selection of diesel filters, RV parts, pool equipment, and automotive components — all backed by fast US shipping and our satisfaction guarantee.

Read more less

68235275AA Fuel Filter + 61150 Wrench Kit — Ram 1500 EcoDiesel Service Combo Everything you need for a clean, frustration-free fuel filter change on your 2014-2019 Ram 1500 3.0L EcoDiesel—in one package. The iFJF 68235275AA Fuel Filter + 61150 Wrench Combo Kit includes the correct OEM-spec fuel filter cartridge plus our popular billet aluminum housing wrench. When you buy the kit, you save 20% versus purchasing separately—and avoid the headache of a cracked filter cap from using wrong tools. What is Included 68235275AA Fuel Filter: OEM-equivalent cartridge with 10-micron filtration and water-separating media. Includes new O-rings. 61150 Aluminum Filter Wrench: CNC-machined billet aluminum wrench that perfectly engages EcoDiesel hex filter cap. Key Features Complete Service Kit: Filter + wrench—walk out to your truck and get the job done, no extra trips to parts store OEM-Spec Filtration: 10-micron filter with water-separation protects high-pressure pump and piezo injectors Billet Wrench Protection: 61150 wrench eliminates the number one cause of EcoDiesel filter cap failure Kit Savings: 20% off combined price—the wrench practically pays for itself on first filter change Includes O-Rings: Cap O-ring and housing seal included—replace every filter change for reliability Compatibility Vehicle Engine Years Ram 1500 3.0L V6 EcoDiesel (EXF) 2014-2019 Specifications Specification Detail Part Number FJ-75AA-CAP06 Filter 68235275AA — 10 Micron Cartridge Wrench 61150 — Billet Aluminum, 3/8 inch Drive DIY Filter Change Steps Locate fuel filter housing on passenger side of engine bay Place rags under housing—some diesel will spill Open water drain (white knob) to drain housing Use 61150 wrench with 3/8 inch ratchet to unscrew cap Pull out old filter, replace both O-rings Insert new 68235275AA filter, ensure it clicks into cap Hand-tighten cap, then 1/4 turn with wrench Cycle ignition to Run (without starting) 10-15 times to prime Start engine and check for leaks Frequently Asked Questions Q: Does this fit my 2017 Ram EcoDiesel?A: Yes. Both filter and wrench fit all 2014-2019 Ram 1500 3.0L EcoDiesel models. Q: Same filters the dealer uses?A: Premium aftermarket equivalent meeting or exceeding Mopar 68235275AA specifications. Q: How to prime after changing?A: Cycle ignition from OFF to RUN (do not start) 10-15 times. Each cycle runs in-tank lift pump for 2 seconds. Q: Fits Jeep Grand Cherokee EcoDiesel?A: Yes. 2014-2019 Grand Cherokee uses same 3.0L EcoDiesel and same 68235275AA filter. Q: Why replace O-rings every time?A: O-rings take compression set and can develop micro-cracks causing air intrusion, hard starts, and no-start conditions. Related Products 68229402AA Oil Filter for EcoDiesel 68235275AA + 68229402AA Fuel and Oil Combo Helpful Articles iFJF Blog — Ram EcoDiesel DIY Guides

Read more less

61150 Fuel Filter Housing Wrench — Precision Tool for Ram 1500 EcoDiesel Changing the fuel filter on your 2014-2019 Ram 1500 3.0L EcoDiesel should not be a wrestling match. The iFJF 61150 Fuel Filter Wrench is CNC-machined from billet aluminum for a perfect fit on the EcoDiesel's filter housing cap—no slipping, no damage, no frustration. The factory plastic cap is notorious for rounding off when using generic strap wrenches or pliers. This purpose-built tool engages all six flats of the hex cap evenly, distributing torque and eliminating the risk of cap damage during removal and installation. Key Features Precision CNC-Machined Aluminum: 6061-T6 billet aluminum construction—lightweight yet far stronger than the factory plastic cap Perfect 6-Point Engagement: Machined to exact OEM cap dimensions for zero-slop fit—no rounding, no slipping 3/8 inch Square Drive: Compatible with standard ratchets, breaker bars, and torque wrenches for controlled tightening Corrosion-Resistant Finish: Clear anodized surface protects against diesel fuel exposure and workshop chemicals Compact Design: Slim profile fits in tight engine bay clearances without removing surrounding components Compatibility Vehicle Engine Years Ram 1500 3.0L V6 EcoDiesel (EXF) 2014-2019 Jeep Grand Cherokee 3.0L V6 EcoDiesel (EXF) 2014-2019 Specifications Specification Detail Part Number 61150 / FJ-CAP06-RD Material 6061-T6 Billet Aluminum Drive Size 3/8 inch Square Drive Finish Clear Anodized Why You Need This Wrench The Ram EcoDiesel's fuel filter cap is plastic and easily damaged by generic tools. Dealerships charge $150+ for a filter change—and if they crack your cap, it is a tow bill plus $200+ for a new housing. At under $20, the 61150 aluminum wrench is the cheapest insurance for your EcoDiesel. Frequently Asked Questions Q: Will this wrench work on my 2016 Ram EcoDiesel?A: Yes. The 61150 wrench fits all 2014-2019 Ram 1500 models with the 3.0L V6 EcoDiesel, regardless of trim level. Q: Can I use a regular oil filter wrench instead?A: We strongly advise against it. Generic strap or claw wrenches can crush the plastic cap or round off hex flats. The 61150 engages all six flats evenly with zero play. Q: Does this also fit the Jeep Grand Cherokee EcoDiesel?A: Yes. The 2014-2019 Jeep Grand Cherokee with 3.0L EcoDiesel uses the same fuel filter housing. Q: What torque spec should I tighten the cap to?A: Hand-tighten, then 1/4 turn with wrench. Factory spec is approximately 18-22 ft-lbs. The O-ring does the sealing, not the torque. Q: Is this better than the plastic OEM 61150 wrench?A: This is an upgraded aluminum version. Billet construction provides superior durability and will not crack or wear over repeated use. Related Fuel Filter Products 68235275AA Fuel Filter + 61150 Wrench Kit 68235275AA Fuel + 68229402AA Oil Filter Combo Helpful Articles iFJF Blog — Ram EcoDiesel Maintenance Guides

Read more less

FL2016 Oil Filter & Billet Aluminum EC781 Cap for 6.0L/6.4L Powerstroke Upgrade your 2003-2010 Ford F250-F550 Super Duty 6.0L and 6.4L Powerstroke oil filtration with this FL2016 oil filter + billet aluminum EC781 cap kit. The factory plastic oil filter cap is notorious for cracking, swelling, and stripping — our CNC-machined 6061-T6 aluminum cap eliminates this failure point permanently. Key Features Billet Aluminum EC781 Cap: CNC-machined 6061-T6 aluminum, silver anodized — replaces the failure-prone OEM plastic cap that cracks and strips. FL2016 Oil Filter: High-capacity cartridge for the 15-quart 6.0L/6.4L Powerstroke oil system — maintains pressure under heavy towing. Permanent Upgrade: Unlike the OEM plastic cap that's a wear item, the billet aluminum cap lasts the life of the engine. 36mm Hex Drive: Standard 36mm socket — no more stripped plastic hex or special cap wrenches. IATF 16949 Certified: 100% leak tested and burst pressure verified. Technical Specifications Specification Value Oil Filter FL2016 / 3C3Z-6731-AA / 1840752C91 Cap Material 6061-T6 Billet Aluminum, Silver Anodized Cap Socket 36mm Hex Thread Standard Ford 6.0L/6.4L Oil Filter Housing Engine 6.0L (2003-2007) / 6.4L (2008-2010) Powerstroke Vehicle & Engine Compatibility Year Make Model Engine 2003-2007 Ford F-250/F-350/F-450/F-550 Super Duty 6.0L Powerstroke V8 2008-2010 Ford F-250/F-350/F-450/F-550 Super Duty 6.4L Powerstroke V8 2003-2005 Ford Excursion 6.0L Powerstroke V8 2003-2010 Ford E-350/E-450 Super Duty 6.0L / 6.4L Why Choose This Product?The OEM plastic oil filter cap on 6.0L and 6.4L Powerstrokes is a well-documented failure point. Heat cycling causes swelling — making changes a nightmare. Stripped hex drives mean cutting the cap off. The billet aluminum EC781 cap is the permanent fix: install once, never fight a stuck cap again. Installation Notes Use 36mm socket — do NOT use an impact wrench Torque to 18-22 ft-lbs (factory spec) Apply clean oil to new filter O-ring before installation Cap can be reused for engine life — just replace the filter element Frequently Asked Questions Q: Will this cap fit my 6.4L Powerstroke?A: Yes. The EC781 billet cap fits both 6.0L (2003-2007) and 6.4L (2008-2010) Powerstroke engines. Same oil filter housing across both generations. Q: How is this better than OEM plastic?A: The OEM plastic cap cracks, swells from heat, and strips at the hex. The billet aluminum cap eliminates these issues permanently with metal that doesn't degrade. Q: Do I need a special socket?A: No. Standard 36mm socket. The OEM plastic cap also uses 36mm but often strips because the plastic rounds off. Q: Can I reuse this cap?A: Yes! The billet cap is a permanent replacement. Simply unscrew, swap the filter element, lubricate the O-ring, and reinstall. Torque to 18-22 ft-lbs. Order your iFJF replacement part today and experience the quality difference. Fast shipping from our US warehouse.

Read more less

Product Overview The EC781 Oil Filter Cap is a precision-engineered replacement for the OEM plastic oil filter housing cap found on 2003-2010 Ford F-Series Super Duty trucks and Excursion SUVs with the 6.0L and 6.4L Powerstroke diesel engines. Designed to replace OEM part numbers 3C3Z-6766-CA and 1840754C91, this cap provides reliable sealing and easy removal for every oil change. Key Features Precision 36mm Hex Drive: Sharp, well-defined hex flats ensure your socket grips firmly — no slipping, no rounding, unlike worn OEM plastic caps. Exact OEM Fitment: Identical thread pitch, height, and sealing surface to the factory cap. Drop-in replacement — threads into your existing oil filter housing. Includes Replacement O-Ring: New O-ring seal included. Always replace the O-ring at every service to prevent the slow oil seepage that's common when old seals are reused. Compatible with All FL2016 Cartridges: Works with Motorcraft, WIX, Baldwin, Fleetguard, and all aftermarket FL2016/PF2016-spec filter elements. Compatibility Year Make Model Engine 2003-2007 Ford F-250/F-350/F-450/F-550 Super Duty 6.0L Powerstroke V8 2008-2010 Ford F-250/F-350/F-450/F-550 Super Duty 6.4L Powerstroke V8 2003-2005 Ford Excursion 6.0L Powerstroke V8 2003-2010 Ford E-350/E-450 Super Duty Van 6.0L Powerstroke V8 Specifications Specification Value Part Number FJ-CAP03-CK OE Cross Reference 3C3Z-6766-CA, 1840754C91 Socket Size 36mm Hex Torque Specification 18-22 ft-lbs (25-30 Nm) Filter Compatibility FL2016, PF2016, 57316, BT7349, LF16161 Includes Filter Cap + Replacement O-Ring Seal Frequently Asked Questions Q: Is this the same as the OEM plastic cap?A: It's a direct dimensional replacement but made from higher-quality materials. The OEM cap (3C3Z-6766-CA) is injection-molded plastic that fails over time. Our EC781 cap is engineered for durability with precise machining for reliable socket engagement every oil change.Q: Does this cap come with an O-ring?A: Yes. A new O-ring seal is included. Always replace the O-ring at every oil change — reusing old O-rings is the #1 cause of oil filter housing leaks on 6.0L/6.4L engines.Q: What is the correct installation torque?A: Tighten to 18-22 ft-lbs (25-30 Nm). Hand-tighten until the O-ring contacts the housing, then 1/4 turn with a torque wrench and 36mm socket. Do NOT exceed 25 ft-lbs — over-torquing can damage the aluminum housing threads.Q: Does this cap fit all FL2016 filter cartridges?A: Yes. Compatible with Motorcraft FL2016, WIX 57316, Baldwin BT7349, Fleetguard LF16161, and all other FL2016/PF2016-spec cartridges.

Read more less

68157291AA Fuel Filter + Silver Canister Housing Cap — Ram 6.7L Cummins Do not let a $25 plastic cap cost you thousands in fuel system repairs. The iFJF 68157291AA Fuel Filter + Silver Aluminum Housing Cap Combo permanently solves the notorious Ram plastic cap problem while providing OEM-grade 3-micron fuel filtration for your 2011-2020 Ram 2500/3500 6.7L Cummins. The silver anodized billet aluminum cap (replaces 68065612AA) is CNC-machined for perfect fit and features a brilliant silver finish that resists corrosion through years of filter changes. Key Features Complete Kit: 68157291AA filter + 68065612AA silver aluminum cap + new O-ring—everything in one box Billet Aluminum Cap — Silver: 6061-T6 aircraft-grade aluminum with clear anodized finish for maximum corrosion resistance 3-Micron Filtration: Captures 99.9% of particles 3 microns and larger—critical CP3/CP4 protection Water-Separating Media: Hydrophobic filter element removes water before it damages injectors Precision Hex Drive: Identical hex size to factory cap (1-1/4 inch or 32mm) for existing tool compatibility Compatibility Vehicle Engine Years Ram 2500 6.7L Cummins Turbo Diesel 2011-2020 Ram 3500 6.7L Cummins Turbo Diesel 2011-2020 Ram 4500/5500 6.7L Cummins Turbo Diesel 2011-2020 Specifications Specification Detail Part Number FJ-91AA-CAP01-RD Filter 68157291AA — 3 Micron, Water Separating Cap 68065612AA Replacement — Billet Aluminum, Silver Cap Material 6061-T6 Aluminum, Clear Anodized Installation Tips Place drain pan under chassis-mounted filter housing (driver-side frame rail) Open water drain valve (yellow lever) to drain housing Use 1-1/4 inch socket or 32mm wrench to unscrew old plastic cap Remove old filter element and discard Clean housing interior with lint-free cloth Insert new 68157291AA filter element Lubricate O-ring with clean diesel fuel Install new aluminum cap—hand-tighten then 1/4 turn (18-22 ft-lbs) Cycle key to Run (without starting) 3 times to prime Start engine and check for leaks Frequently Asked Questions Q: Difference between silver and black cap?A: Mechanically identical. Same billet 6061-T6 aluminum, same OEM-spec dimensions. Difference is cosmetic: silver (clear anodized) vs black (hard anodized). Q: Will this fit my 2013 Ram 3500 dually?A: Yes. All 2011-2020 Ram 2500/3500 with 6.7L Cummins use the same front fuel filter housing, including dually configurations. Q: Signs my old cap is bad?A: Fuel weeping around cap threads, stripped hex, visible cracks at O-ring groove, or air in fuel system causing extended cranking. Q: Buy cap without filter?A: This listing includes both. For cap only, search 68065612AA on our store. Q: Does silver anodizing hold up to diesel?A: Yes. MIL-A-8625 Type II anodized finish is chemically resistant to diesel, DEF, and engine bay chemicals. Related Products Same Kit — Black Cap Version 68157291AA + 68436631AA Two-Filter Kit Helpful Articles iFJF Blog — Diesel Fuel System Maintenance

Read more less

Complete fuel filter kit for Ram 6.7L Cummins diesel trucks (2011-2020). Includes OEM-spec 68157291AA filter element AND 68065612AA black billet aluminum housing cap. Direct fit for 2500, 3500, 4500, 5500 models. Superior filtration protects your CP4/CP3 injection pump.How to install: Ram 6.7L Cummins: Change BOTH Fuel Filters — Step-by-Step

Read more less