Off Road

Maximize Your Jeep's Interior Space The iFJF Mesh Top Roof Cargo Net transforms wasted ceiling space into functional overhead storage. Designed for Jeep Wrangler YJ, TJ, LJ, JK, JL, and Gladiator JT (1987–2021), this heavy-duty elastic mesh net secures jackets, blankets, camping gear, and everyday essentials above your head — keeping the cabin organized without sacrificing passenger comfort or legroom. Key Features High-Elasticity Mesh — Premium-grade 4-way stretch nylon mesh conforms to irregular cargo shapes while maintaining tension for a secure hold on pavement and off-road. Universal Wrangler Compatibility — Custom-fit design covers every Wrangler generation: YJ (1987–1995), TJ & LJ (1997–2006), JK 2-Door & 4-Door (2007–2018), JL 2-Door & 4-Door (2018–2021), and Gladiator JT (2020–2021). Quick Install & Secure Mounting — Heavy-duty adjustable straps with quick-release buckles attach to factory roll bars, sport bars, and hardtop mounting points in minutes. No drilling, no permanent modifications required. Durable All-Black Construction — UV-resistant black mesh and black hardware blend seamlessly with any interior color. Won't fade, sag, or stretch out over time. Off-Road Ready — Keeps gear firmly in place during trail rides, rock crawling, and daily commutes. Say goodbye to flying cargo on bumpy terrain. Multi-Purpose Design — Use as a roof cargo organizer, a rear-seat barrier to keep pets and children safely in the back, or roll up the rear window for fresh airflow with the built-in straps. Compatibility Model Generation Years Wrangler YJ 1st Gen 1987–1995 Wrangler TJ / LJ 2nd Gen 1997–2006 Wrangler JK (2-Door & 4-Door) 3rd Gen 2007–2018 Wrangler JL (2-Door & 4-Door) 4th Gen 2018–2021 Gladiator JT Pickup 2020–2021 Installation Guide Unfold the cargo net and identify the attachment straps (4–6 points depending on your model). Clip the front straps around the windshield frame or front sport bar crossmember. Secure the rear straps to the rear roll bar or sound bar — adjust strap length for a snug, taut fit. Route side straps to the side sport bars and tighten evenly across all points. Double-check all buckles are locked and the net sits flat with uniform tension. Load lightweight gear (jackets, blankets, soft bags) evenly across the net. For best results, avoid exceeding 15 lbs total. Frequently Asked Questions Q: Will this cargo net work with a hardtop installed? A: Yes. The net mounts to the roll bars and sport bars underneath the hardtop — it does not interfere with hardtop or soft top installation or removal. Q: How much weight can the net hold? A: We recommend a maximum load of 15 lbs (6.8 kg) distributed evenly. The net is designed for soft goods like clothing, blankets, and light camping gear — not heavy tools or recovery equipment. Q: Does it block rearview mirror visibility? A: When loaded with bulky items, the net may partially obstruct the rearview mirror. We recommend loading items toward the sides and keeping the center clear for maximum visibility. Q: Is it compatible with the factory Freedom Top panels on JK/JL? A: Absolutely. The net sits below the Freedom Top panels and does not affect panel installation, removal, or weather sealing. Q: Will the straps scratch or damage my roll bars? A: No. The straps feature smooth inner surfaces and quick-release buckles. They wrap securely around the roll bars without scratching or leaving marks.

Read more less

Product Overview Protect your Jeep's door locks and add a custom touch with these magnetic keyhole covers, designed specifically for the 2018-2024 Jeep Wrangler JL and Gladiator JT. The Black Flag design delivers a rugged, patriotic look while the weatherproof magnetic seal keeps moisture, dirt, and road salt out of your keyholes — preventing rust, freezing, and theft. Installation takes seconds with no tools or adhesive required. Key Features Strong Magnetic Hold: Built-in high-strength magnet holds the cover securely against the lock face at highway speeds and on rough trails. Weatherproof Protection: Silicone sealing pad creates a water-resistant barrier that keeps rain, snow, mud, and road salt out of your door locks. Premium Construction: High-quality resin body with UV-resistant finish — will not fade, crack, or yellow from sun exposure. Rubber-Coated Magnet: Soft rubber coating on the magnet prevents scratches on your Jeep's paint around the keyhole. Tool-Free Installation: Simply place the cover over the keyhole — the magnet does the rest. Remove and reinstall in seconds. Perfect OEM Fit: Precision-molded to match the exact contours of JL and JT door lock cylinders. Compatibility Year Make Model Trims 2018-2024 Jeep Wrangler JL (2-Door & 4-Door) Sport, Sport S, Sahara, Rubicon, 4xE, 392, Willys 2020-2024 Jeep Gladiator JT Sport, Sport S, Overland, Rubicon, Mojave, Willys Note: These covers protect the physical keyhole only. Keyless entry, remote start, and proximity key functions are unaffected. Specifications Specification Value Material High-Quality Resin + Rubber Seal Design Black Flag (Patriotic American Flag Pattern) Attachment Magnetic (rubber-coated, scratch-free) Weather Resistance Waterproof seal, UV-resistant finish Installation No tools, no adhesive, instant placement Installation Clean the keyhole area with a microfiber cloth to remove any dust or dirt Position the magnetic cover over the driver-side door keyhole The magnet will automatically align and hold the cover in place Repeat for the passenger-side door To remove, simply pull the cover off — no residue or marks left behind Why Choose iFJF iFJF Direct is a trusted source for Jeep Wrangler and Gladiator accessories. From keyhole covers to door hinge solutions, we stock hundreds of products designed specifically for the JL and JT platform. Fast shipping from US warehouses and responsive customer support mean you spend less time waiting and more time on the trail. Related Products Jeep Wrangler JL/JT Magnetic Keyhole Covers — Standard design option Jeep Door Bushing Removal Tool — Essential for door removal Jeep Wrangler JL Hood Latches — Keep your engine bay secure Jeep Tailgate Rubber Plug Set — Weatherproof your tailgate Frequently Asked Questions Q: Will these fit my 2024 Jeep Wrangler 4xE?A: Yes, these keyhole covers are compatible with all 2018-2024 Wrangler JL models including the 4xE plug-in hybrid. The keyhole design is identical across all JL trims. Q: Do these interfere with keyless entry or remote start?A: No. The covers only protect the physical keyhole. Your key fob proximity sensor, push-button start, keyless entry, and remote start all function normally with the covers installed. Q: Will they stay on at highway speeds?A: Yes, the high-strength magnet is engineered to hold securely at all driving speeds. Extensive testing confirms the covers stay in place even at 80+ MPH and on rough off-road terrain. Q: Do the covers cause any paint damage?A: No. The magnet is rubber-coated to prevent scratching, and the silicone seal is paint-safe. The covers leave no residue when removed. Q: Can I paint or customize these covers?A: The surface can be painted with automotive-grade spray paint. Lightly sand with 800-grit paper, apply plastic adhesion promoter, then paint in thin coats. Allow 24 hours to fully cure before installation. Q: Do these work on the tailgate lock?A: These covers are designed for the front door keyholes. The tailgate keyhole is a different shape and these covers may not fit properly. Q: Will they freeze to the lock in winter?A: The silicone gasket creates a barrier that prevents moisture from reaching the keyhole, actually reducing the chance of freezing compared to an uncovered lock. In extreme ice conditions, gently warm the cover with your hand before removal.

Read more less

Overview Enhance both safety and style on your Jeep Wrangler JL or Gladiator JT with the iFJF LED 3rd Brake Light Board. Equipped with 5 high-output LEDs behind a light-amplifying smoke lens this direct replacement delivers significantly brighter illumination than the factory incandescent unit — making you more visible to following traffic in all weather conditions. The black housing with smoke lens adds a custom aggressive look while plug-and-play design means installation takes just minutes with no wiring modifications required. Compatibility Year Make Model Configuration 2018-2023 Jeep Wrangler JL 2-Door and 4-Door (JLU) 2020-2023 Jeep Gladiator JT All Trims Key Features 5 High-Output LEDs: Superior brightness with instant-on response — illuminates faster than factory incandescent bulbs for improved reaction time from following drivers Light-Amplifying Smoke Lens: Specialized diffuse lens maximizes LED output while providing sleek smoked appearance True Plug-and-Play: Uses factory wiring connector — no cutting splicing or resistors required. Simply unplug old and plug in new Waterproof ABS Housing: Sealed construction prevents moisture intrusion eliminating common factory issue of water-fogged lenses Scratch-Resistant Surface: Special surface treatment resists scratches from keys fingernails and routine contact Black Housing Design: Aggressive blacked-out look replaces factory red housing for custom modern aesthetic Technical Specifications Specification Value Dimensions 6.3 x 2.4 x 1.8 Inches (160 x 61 x 46mm) LED Count 5 High-Output LEDs Lens Color Smoke (Dark Tinted) Housing Color Black ABS Material ABS Engineering Plastic (Waterproof) Installation Plug-and-Play Factory Connector Voltage 12V DC Standard Vehicle Electrical Installation Open the rear tailgate / swing gate on your Jeep Wrangler or Gladiator Locate the factory 3rd brake light assembly above the spare tire mount Remove factory mounting screws using Torx or Phillips screwdriver Disconnect factory wiring harness connector from back of brake light Connect iFJF LED brake light to factory wiring harness — it clicks into place Position new unit and secure with factory mounting screws Test brake light function by pressing brake pedal Installation time: 5-10 minutes. No special tools beyond basic screwdriver. Why Choose iFJF? Brighter Equals Safer: LED technology delivers significantly more light output than factory bulb giving drivers behind you more reaction time Jeep-Specific Design: Engineered exclusively for JL and JT platform — perfect fit factory connector no modifications needed Weatherproof Construction: Unlike factory units that can fog up the iFJF light is fully sealed against elements Instant Installation: The easiest upgrade you will ever do on your Jeep — plug-and-play in under 10 minutes FAQ Q: Will this fit my 2022 Jeep Wrangler JL Unlimited?A: Yes designed for all 2018-2023 Jeep Wrangler JL and JLU 2-door and 4-door models plus 2020-2023 Gladiator JT. Q: Is the smoke lens legal in all states?A: LED output is brighter than factory and meets DOT brightness standards but some states restrict tinted/smoked lenses for brake lights. Check local regulations. Q: Do I need to add resistors or modify wiring?A: No. True plug-and-play unit connects directly to factory wiring harness. No resistors relays or wiring modifications needed. Q: Will water get inside like factory unit?A: iFJF unit features fully sealed waterproof ABS housing preventing moisture intrusion — common upgrade over factory units known to fog up. Q: Does this work with factory spare tire carrier and backup camera?A: Yes designed as direct replacement and does not interfere with factory spare tire carrier or backup camera system. Q: Is light output significantly brighter than factory?A: Yes 5 high-output LEDs produce noticeably brighter more vivid illumination with faster on/off response time than factory incandescent bulb.

Read more less

Product Overview The iFJF Interior Door Grab Handle Inserts Cover Door Handle Trim Cover for Wrangler JK JKU 2011-2018 2 Door and 4 Door 2Pcs (Red Carbon Pattern) from iFJF is a precision-engineered aftermarket upgrade designed to deliver exceptional performance, durability, and value. Crafted from premium-grade materials, this interior accessory combines practical functionality with sleek aesthetics. Designed specifically for your vehicle, it provides a seamless OEM-quality fit while enhancing comfort, convenience, and organization. Vehicle Compatibility This product is designed for the following vehicles: Please verify compatibility with your specific vehicle year, make, model, and engine configuration before purchasing. Contact our support team if you need assistance confirming fitment for your application. Note: Professional installation is recommended. Verify fitment for your specific sub-model, cab configuration, and drivetrain (2WD/4WD) before ordering. Key Features Premium-Grade Materials: High-quality ABS plastic, carbon fiber pattern, or durable nylon construction Custom Vehicle-Specific Fit: Precision-molded to match your vehicle's interior contours exactly Easy Installation: No drilling or permanent modifications — installs in minutes with basic tools Enhanced Interior Aesthetics: Upgrades the look and feel of your cabin Practical Functionality: Adds storage, organization, or protection to high-wear areas Technical Specifications Specification Details Material High-quality ABS plastic with UV-resistant finish Exact Fit: Custom molded for Wrangler JK/JKU 2011-2018 models Easy Install: Direct replacement inserts - no modification required 2-Piece Set: Includes covers for both driver and passenger side grab handles Compatibility Jeep Wrangler JK (2011-2018) - 2 Door Jeep Wrangler JKU Unlimited (2011-2018) - 4 Door Installation Remove original grab handle screws (Torx T20) Detach original handle from mounting points Install new handle inserts in place Reinstall with original hardware Package Includes 2 × Door Grab Handle Inserts (Red Carbon Pattern) FAQ Q: Do I need special tools to install? A: You will need a Torx T20 bit to remove the original handles. Basic hand tools are sufficient. Q: Will this fit my 2007 Wrangler JK? A: No, these are designed for 2011-2018 JK/JKU models only. The handle design changed in 2011. Q: Is the carbon pattern real carbon fiber? A: This is a high-quality carbon pattern finish on durable ABS plastic for a premium look at an affordable price. Brand iFJF Condition New Warranty Contact iFJF Support for warranty details Installation Guide Clean Surface: Wipe the installation area thoroughly with isopropyl alcohol to remove all dirt and oils. Dry Fit: Test-fit the accessory before removing any adhesive backing to confirm alignment. Apply: Peel adhesive backing and carefully position the accessory. Press firmly for 30-60 seconds across the entire surface. Cure: Allow adhesive to cure for 24 hours before exposure to moisture or extreme temperatures. Recommended: Professional installation is always recommended for optimal results. Installation time varies by vehicle and experience level — typically 1-3 hours. Frequently Asked Questions Q: Does this come with installation hardware? A: Yes. The kit includes all necessary gaskets, bolts, nuts, and mounting hardware required for a complete installation. Q: Is professional tuning required after installation? A: For most applications, no tuning is required for basic operation. Contact our support team for vehicle-specific recommendations. Q: What is the warranty on this product? A: iFJF stands behind all products with comprehensive warranty coverage. Please contact our customer service team for specific warranty terms and conditions applicable to this product. Q: How long does shipping take? A: Most orders ship within 1-2 business days. Delivery times depend on your location and selected shipping method. You'll receive tracking information as soon as your order ships. Why Choose iFJF? Quality You Can Trust: Every iFJF product is manufactured to rigorous quality standards using premium materials and advanced production techniques. We don't cut corners — we engineer parts that perform and last. Direct-Fit Engineering: Our products are designed using precision CAD/CAM technology and verified against OEM specifications, ensuring a hassle-free installation that fits right the first time. Performance Proven: From daily drivers to track machines, iFJF parts deliver measurable improvements in horsepower, torque, throttle response, and overall driving experience. Exceptional Value: We offer premium-quality parts at competitive prices, giving you the best performance-per-dollar in the aftermarket industry. Dedicated Support: Our knowledgeable team is here to help — before, during, and after your purchase. Questions about fitment, installation, or performance? We've got answers. Fast, Reliable Shipping: We process and ship orders quickly from our US warehouses, so you spend less time waiting and more time enjoying your upgraded vehicle. Related Products Complete your build with these complementary iFJF products: All-Weather Floor Mats — Protect your interior with custom-fit durable floor liners Center Console Organizer Tray — Add even more storage and organization to your vehicle Seat Back Protector — Shield your seats from cargo, pets, and daily wear

Read more less

Interior Door Grab Handle Trim Inserts for 2011-2018 Jeep Wrangler JK & JKU Refresh the worn, scratched interior of your Jeep Wrangler JK with these precision-fit door grab handle trim inserts. Designed to cover the factory door pull handle recesses on 2011-2018 Wrangler JK and JKU models (both 2-door and 4-door), these trim covers instantly upgrade your interior appearance while protecting the original plastic from further wear. The peel-and-stick installation takes minutes — no tools, no drilling, no mess. Key Features Precision Fit for JK/JKU: Laser-measured to match the exact contours of 2011-2018 Wrangler JK door handle recesses — flush fit with no gaps or overhang Premium ABS Construction: High-quality ABS plastic with UV-resistant coating — won't fade, crack, or peel under extreme sun exposure or temperature swings Peel-and-Stick Installation: Pre-applied 3M automotive-grade adhesive backing — clean the surface, peel the liner, press firmly, done in under 5 minutes per door Protects Factory Trim: Covers existing scratches and protects the original door panel from further wear caused by rings, keys, and daily use 2-Piece Set: Includes both driver and passenger side inserts — complete interior upgrade in one package Compatibility Year Range Make Model Doors 2011-2018 Jeep Wrangler JK 2-Door & 4-Door (JKU) 2011-2018 Jeep Wrangler Unlimited JKU 4-Door Note: Not compatible with 2007-2010 JK models (different door panel design). For JL/JT models (2018+), different inserts are required. Why Upgrade Your JK Door Handles? The factory JK door panel around the grab handle area is a high-touch zone — every time you close the door, your fingers contact this surface. Over years of use, the soft-touch factory coating wears through, leaving behind an unsightly scratched and peeling surface. These trim inserts are the easiest, most affordable way to restore that factory-fresh look without replacing entire door panels. Frequently Asked Questions Q: Will these fit a 2015 JKU 4-door?A: Yes, these inserts are designed for all 2011-2018 Wrangler JK and JKU models, both 2-door and 4-door. The door grab handle recess is identical across all trim levels (Sport, Sahara, Rubicon). Q: Do they work on a 2008 JK?A: No. The 2007-2010 JK models have a different interior door panel design with a different handle recess shape. This product is specifically for 2011-2018 JK models with the updated interior. Q: How do I install these?A: 1) Clean the door handle recess thoroughly with alcohol wipes. 2) Dry completely. 3) Peel the red backing film from the insert. 4) Align carefully and press firmly for 30 seconds. For best adhesion, install at room temperature (above 60°F). Q: Will the adhesive damage my factory door panel?A: The 3M automotive adhesive is designed to bond securely while remaining removable without residue — unlike generic double-sided tape. If you ever need to remove the inserts, use a heat gun on low setting and peel slowly. Q: Are these available in different colors/finishes?A: Check our store for additional finish options including carbon fiber pattern, brushed aluminum, and matte black. Each option provides the same precision fit with a different aesthetic. 📚 Related Guides & Articles Jeep Wrangler JK vs JL Parts Compatibility Guide Top 10 Jeep Wrangler Mods Under $50 Jeep Wrangler JK Common Problems & Fixes

Read more less

iFJF Hood Latches Lock Catch Kit for Jeep Wrangler JK JKU 2007-2018 — Black Stainless Steel Eliminate hood flutter and upgrade security on your Jeep Wrangler JK with the iFJF Hood Latches Lock Catch Kit. The factory rubber hood latches on 2007-2018 Wranglers are a well-known weak point — they stretch over time, causing the hood to flutter at highway speeds and creating a distracting, unsettling driving experience. This kit replaces the factory latches with heavy-duty black stainless steel locking catches that hold the hood firmly in place while adding a layer of anti-theft protection. Engineered for direct bolt-on fitment with no drilling or modifications required. Key Features Eliminates Hood Flutter: The factory rubber latches stretch and weaken over time, causing the hood to visibly flutter at speeds above 55 MPH. This aluminum/stainless steel latch kit locks the hood down tight, eliminating the flutter completely — even at interstate speeds and in crosswinds. Anti-Theft Locking Mechanism: Each latch incorporates a keyed lock that prevents the hood from being opened without the key. This protects your battery, aftermarket accessories, and under-hood components from theft — a common concern for Jeep owners who leave their vehicles parked with the top off. Black Stainless Steel Construction: The black powder-coated finish provides corrosion resistance and a sleek, aggressive appearance that complements any JK color scheme. Unlike raw aluminum latches that oxidize, the black coating stays looking new through mud, snow, and sun exposure. Direct Bolt-On Installation: Uses the factory mounting holes — no drilling, no cutting, no modifications required. Each latch mounts in place of the OEM rubber unit using the existing hardware locations. Most owners complete the installation in under 30 minutes with basic hand tools. Adjustable Tension: The latch mechanism allows tension adjustment to achieve the perfect fit — tight enough to eliminate flutter, but not so tight that it's difficult to close the hood. Complete Pair: Includes both driver and passenger side latches with matching keys. Both sides lock independently for full security coverage. Vehicle Compatibility Jeep Wrangler JK (2-Door): 2007-2018 Jeep Wrangler JKU (4-Door): 2007-2018 Replaces factory rubber hood latches on all JK and JKU trim levels (Sport, Sahara, Rubicon, X, Freedom, Willys, etc.) Does NOT fit: 1997-2006 TJ/LJ models, 2018+ JL/JLU models (different latch design) Why Replace Your Factory Hood Latches? Jeep equipped every JK Wrangler from the factory with simple rubber T-handle hood latches. These latches work adequately when new, but the rubber compound degrades under UV exposure and repeated stretching. Within 2-3 years — or sooner in hot climates — the latches lose tension and the hood begins to flutter. At 65 MPH on the highway, the flutter is not just annoying; it can be genuinely alarming, with the hood visibly bouncing several inches. Over time, this movement wears the hood latch striker and can damage the hood itself. Beyond the flutter, factory latches offer zero security — anyone can open your hood. This iFJF locking latch kit solves both problems in one 30-minute upgrade that pays for itself in driving comfort and peace of mind. Package Includes 1 × Driver Side Black Stainless Steel Locking Hood Latch 1 × Passenger Side Black Stainless Steel Locking Hood Latch 2 × Matching Keys All Necessary Mounting Hardware Installation Guide Frequently Asked Questions How difficult is the installation? Very straightforward. Most customers complete both sides in 20-30 minutes with basic hand tools. The kit uses the factory mounting holes — remove the old rubber latch (2 bolts per side), bolt the new locking latch in place, adjust the tension, and you're done. No drilling required. Will these rust over time? No. The black powder-coated stainless steel construction provides excellent corrosion resistance. These latches are designed to withstand mud, rain, snow, salt, and sun exposure without rusting or fading. Can I use these on a 2019 JL Wrangler? No. This kit is specifically designed for the JK platform (2007-2018). The JL uses a completely different hood latch design and mounting pattern. We recommend verifying your model year before ordering. What happens if I lose the key? Keep your spare key in a safe place. If both keys are lost, the locks can be drilled out and replaced. Contact iFJF customer support for replacement lock cylinder options. Why Choose iFJF? iFJF specializes in premium aftermarket accessories for Jeep Wrangler and off-road vehicles. Our hood latch kit is tested in real-world conditions — highway miles, trail abuse, winter salt, desert heat — to ensure it performs when you need it. Backed by a satisfaction guarantee and responsive US-based customer support. Fast Shipping: Orders ship within 1-2 business days from our US warehouse. 🔗 You May Also Like iFJF Adjustable Roll Bar Fire Extinguisher Holder for Jeep Wrangler JK 2007 iFJF Adjustable Roll Bar Fire Extinguisher Holder for Jeep Wrangler JK 2007 iFJF 91-03 Jeep 91-01 Wrangler 93-01 Cherokee 91-92 Grand Cherokee 4.0L Exh iFJF 1991-1995 2.5L Jeep Wrangler YJ L4 Exhaust Header 📖 Related Installation Guides & Articles 📝 Ball joint removal/install on 2018 ram 4500/5500 diesel. 📝 How to Install a Bluetooth Kill Switch: Anti-Theft Battery Disconnect Guide 📝 Why You Need a Bluetooth Kill Switch for Your RV or Truck

Read more less

Stop Hood Flutter — Upgrade Your JL's Latches The factory hood latches on the 2018-2021 Jeep Wrangler JL are notorious for stretching over time, causing dangerous hood flutter at highway speeds and on rough trails. The iFJF Hood Latch Lock Catch is a direct-fit replacement that restores a tight, secure hold on your hood. Key Features Eliminates Hood Flutter: Stiffer, more durable latch mechanism than OEM. Hood stays planted even at 80+ mph or on washboard roads. Direct Bolt-On Replacement: Uses existing factory mounting points. No drilling or modifications needed. 15-minute install with basic hand tools. Premium Construction: High-grade reinforced polymer body with corrosion-resistant internal components for all-weather durability. Secure Locking Action: Positive-engagement latch with audible click confirms your hood is properly secured every time. Matte Black Finish: Sleek OEM-style appearance with UV-resistant coating that prevents fading. Compatibility Make Model Year Range Jeep Wrangler JL 2018-2021 Jeep Wrangler JLU 2018-2021 Jeep Gladiator JT 2020-2021 Why Replace Your Factory Latches? Wrangler JL owners consistently report hood flutter starting around 15,000-20,000 miles. The rubber latch components stretch and lose tension, causing the hood to visibly bounce at freeway speeds. Our upgraded latch uses a stiffer spring rate and durable polymer that resists stretching, giving you peace of mind for years. Installation Open hood and remove factory latch bolts (10mm socket, 2 per side) Remove old latch assembly Position new iFJF latch over factory holes Reinstall bolts and torque to 15 ft-lbs Close hood and verify secure engagement Specifications Spec Detail Material Reinforced Polymer + Steel Color Matte Black Package 1 Pair (Left + Right) Frequently Asked Questions Q: Difference between this and locking version?A: This is a direct replacement catch without key lock. For anti-theft protection, see our locking model (sold separately). Q: Will this fit a 2022+ JL?A: Designed for 2018-2021 model years. 2022+ may have different mounting — verify before ordering. Q: Does it come as a pair?A: Yes. Each order includes both left and right side latches. Q: DIY install possible?A: Yes! This is a beginner-friendly install. You only need a 10mm socket. Most owners finish in 15 minutes. Q: Will the black finish fade?A: UV-stabilized matte black finish tested for 5+ years of direct sun without fading. Q: Does this eliminate need for hood pins?A: For daily driving and light off-roading, yes. For extreme rock crawling, hood pins are still recommended as secondary safety. 📚 Related Guides & Articles 📖 Jeep Wrangler JL Hood Flutter Fix — Complete Guide

Read more less

Product Overview The iFJF Gear Shift Console Organizer Tray Box and Hanging Armrest Organizer Tray Combination Storage Box for 2018-2020 Wrangler JL (Hanging Storage Box) from iFJF is a precision-engineered aftermarket upgrade designed to deliver exceptional performance, durability, and value. Crafted from premium-grade materials, this interior accessory combines practical functionality with sleek aesthetics. Designed specifically for your vehicle, it provides a seamless OEM-quality fit while enhancing comfort, convenience, and organization. Vehicle Compatibility This product is designed for the following vehicles: Please verify compatibility with your specific vehicle year, make, model, and engine configuration before purchasing. Contact our support team if you need assistance confirming fitment for your application. Note: Professional installation is recommended. Verify fitment for your specific sub-model, cab configuration, and drivetrain (2WD/4WD) before ordering. Key Features Premium-Grade Materials: High-quality ABS plastic, carbon fiber pattern, or durable nylon construction Custom Vehicle-Specific Fit: Precision-molded to match your vehicle's interior contours exactly Easy Installation: No drilling or permanent modifications — installs in minutes with basic tools Enhanced Interior Aesthetics: Upgrades the look and feel of your cabin Practical Functionality: Adds storage, organization, or protection to high-wear areas Technical Specifications Specification Details Material High-quality ABS plastic with matte finish Anti-Slip Design: Rubberized pads prevent items from sliding Easy Install: Drop-in design - no tools or modification required Compatibility Jeep Wrangler JL (2018-2020) Jeep Wrangler JLU Unlimited (2018-2020) Storage Benefits Console Tray: Organizes phone, wallet, keys, sunglasses Hanging Organizer: Additional storage for small items within arm reach Divide Space: Prevents items from getting lost in deep console Package Includes 1 × Center Console Organizer Tray 1 × Hanging Armrest Storage Box FAQ Q: Will this fit my 2021 Wrangler JL? A: This organizer is designed for 2018-2020 JL models. The 2021+ console may have different dimensions. Q: Does it interfere with charging cables? A: No, the tray design allows cable routing for phone charging. Q: Is the hanging organizer removable? A: Yes, both pieces can be easily removed when needed. Brand iFJF Condition New Warranty Contact iFJF Support for warranty details Installation Guide Clean Surface: Wipe the installation area thoroughly with isopropyl alcohol to remove all dirt and oils. Dry Fit: Test-fit the accessory before removing any adhesive backing to confirm alignment. Apply: Peel adhesive backing and carefully position the accessory. Press firmly for 30-60 seconds across the entire surface. Cure: Allow adhesive to cure for 24 hours before exposure to moisture or extreme temperatures. Recommended: Professional installation is always recommended for optimal results. Installation time varies by vehicle and experience level — typically 1-3 hours. Frequently Asked Questions Q: Does this come with installation hardware? A: Yes. The kit includes all necessary gaskets, bolts, nuts, and mounting hardware required for a complete installation. Q: Is professional tuning required after installation? A: For most applications, no tuning is required for basic operation. Contact our support team for vehicle-specific recommendations. Q: What is the warranty on this product? A: iFJF stands behind all products with comprehensive warranty coverage. Please contact our customer service team for specific warranty terms and conditions applicable to this product. Q: How long does shipping take? A: Most orders ship within 1-2 business days. Delivery times depend on your location and selected shipping method. You'll receive tracking information as soon as your order ships. Why Choose iFJF? Quality You Can Trust: Every iFJF product is manufactured to rigorous quality standards using premium materials and advanced production techniques. We don't cut corners — we engineer parts that perform and last. Direct-Fit Engineering: Our products are designed using precision CAD/CAM technology and verified against OEM specifications, ensuring a hassle-free installation that fits right the first time. Performance Proven: From daily drivers to track machines, iFJF parts deliver measurable improvements in horsepower, torque, throttle response, and overall driving experience. Exceptional Value: We offer premium-quality parts at competitive prices, giving you the best performance-per-dollar in the aftermarket industry. Dedicated Support: Our knowledgeable team is here to help — before, during, and after your purchase. Questions about fitment, installation, or performance? We've got answers. Fast, Reliable Shipping: We process and ship orders quickly from our US warehouses, so you spend less time waiting and more time enjoying your upgraded vehicle. Related Products Complete your build with these complementary iFJF products: All-Weather Floor Mats — Protect your interior with custom-fit durable floor liners Center Console Organizer Tray — Add even more storage and organization to your vehicle Seat Back Protector — Shield your seats from cargo, pets, and daily wear

Read more less

Product Overview Upgrade your Jeep's door control with iFJF Retractable Door Limiting Straps in bold red. Factory door check straps are notorious for snapping under wind gusts or off-camber parking — leaving your door to swing freely into the fender or vehicle next to you. These high-strength polyester webbing straps provide controlled, reliable door limiting for 1996-2023 Wrangler CJ, YJ, TJ, JK, JL and 2021+ Gladiator JT models with a vibrant red color that demands attention. Key Features Universal Jeep Fitment: Designed for all Wrangler generations — CJ, YJ, TJ, JK, JL — plus the 2021+ Gladiator JT truck. Simple bolt-on installation using factory door check mounting points. High-Strength Polyester Webbing: Hand-woven strap rated for extreme tensile loads — significantly stronger than the factory rubber/plastic check strap that deteriorates from UV and weather exposure. Retractable Spring Design: Spring-loaded retraction keeps the strap tidy when the door is closed — no dangling or rattling while driving on or off-road. Bold Red Color: Vibrant red webbing with black stitching adds an aggressive, custom look that complements red-accented Jeep builds and makes a statement on the trail. Prevents Costly Door Damage: Stops the door at the correct opening angle, preventing over-extension that dents fenders, cracks hinges, or damages neighboring vehicles. Compatibility Make Model Years Jeep Wrangler CJ 1976-1986 Jeep Wrangler YJ 1987-1995 Jeep Wrangler TJ 1996-2006 Jeep Wrangler JK (2-Door & 4-Door) 2007-2018 Jeep Wrangler JL (2-Door & 4-Door) 2018-2023 Jeep Gladiator JT 2021+ Specifications Specification Details Material High-Strength Polyester Webbing Color Red with Black Stitching Pack Contents 2 x Door Limiting Straps (Front Pair) Installation Bolt-On — Uses Factory Door Check Mounting Points Why Choose iFJF Factory Jeep door checks are a known weak point — the plastic housing cracks, the rubber stretches, and eventually the door swings free into whatever is next to it. Our polyester webbing straps are a permanent fix that looks better than OEM. The vibrant red color makes a bold statement whether you're running doors on the trail or parked at a Jeep meet-up. 90-day satisfaction guarantee. Frequently Asked Questions Q: Do these completely replace the factory door check?A: Yes. These straps replace the entire factory door check assembly. Remove the old check strap from the door and body mounting points, then bolt these in using the same hardware. No drilling or permanent modification required. Q: Will the red color fade over time?A: The polyester webbing is UV-treated to resist fading from sun exposure. With normal use, the red color should remain vibrant for years. For maximum longevity, apply a UV protectant spray periodically if your Jeep is parked outdoors full-time. Q: Can I still remove my doors easily?A: Yes. Simply unbolt the strap from either the door or body side (one bolt) and the door functions as normal for door-off summer driving. Re-attach when you put the doors back on. Q: Are the red straps the same length as the black/orange version?A: Yes. Both color variants use identical strap length and mounting hardware. The only difference is the webbing color and accent stitching. Choose the style that matches your Jeep's personality. Q: How much door opening do these allow?A: The strap length is calibrated to the factory-designed door opening angle — approximately 75-80 degrees on most Wrangler models. This prevents over-extension while still providing full cabin access. Related Products Explore more from our full catalog. iFJF Direct offers thousands of quality replacement parts, tools, and accessories for your vehicle.

Read more less

Product Overview Upgrade your Jeep's door control with iFJF Retractable Door Limiting Straps. Factory door check straps are notorious for snapping under wind gusts or off-camber parking — leaving your door to swing freely into the fender, mirror, or the vehicle next to you. These high-strength polyester webbing straps provide controlled, reliable door limiting for 1996-2023 Wrangler CJ, YJ, TJ, JK, JL and 2021+ Gladiator JT models in a distinctive black and orange color combination. Key Features Universal Jeep Fitment: Designed for all Wrangler generations — CJ, YJ, TJ, JK, JL — plus the 2021+ Gladiator JT truck. Simple bolt-on installation using factory door check mounting points. High-Strength Polyester Webbing: Hand-woven strap rated for extreme tensile loads — significantly stronger than the factory rubber/plastic check strap that deteriorates from UV and weather exposure. Retractable Spring Design: Spring-loaded retraction keeps the strap tidy when the door is closed — no dangling or rattling while driving on or off-road. Stylish Two-Tone Color: Black base with orange accent stitching gives your Jeep a custom look that stands out at the trailhead or in the parking lot. Prevents Costly Door Damage: Stops the door at the correct opening angle, preventing over-extension that dents fenders, cracks hinges, or damages neighboring vehicles. Compatibility Make Model Years Jeep Wrangler CJ 1976-1986 Jeep Wrangler YJ 1987-1995 Jeep Wrangler TJ 1996-2006 Jeep Wrangler JK (2-Door & 4-Door) 2007-2018 Jeep Wrangler JL (2-Door & 4-Door) 2018-2023 Jeep Gladiator JT 2021+ Specifications Specification Details Material High-Strength Polyester Webbing Color Black with Orange Accent Stitching Pack Contents 2 x Door Limiting Straps (Front Pair) Installation Bolt-On — Uses Factory Door Check Mounting Points Why Choose iFJF Factory Jeep door checks are a known weak point — the plastic housing cracks, the rubber stretches, and eventually the door swings free into whatever is next to it. Our polyester webbing straps are a permanent fix that actually looks better than OEM. Each strap is hand-stitched with reinforced end loops for long-term durability on and off the trail. 90-day satisfaction guarantee. Frequently Asked Questions Q: Do these completely replace the factory door check?A: Yes. These straps replace the entire factory door check assembly. Remove the old check strap from the door and body mounting points, then bolt these in using the same hardware. No drilling or permanent modification required. Q: Will these work with tube doors?A: Tube doors typically use different mounting geometry than factory doors. While many customers have successfully adapted these straps, check your tube door's mounting hole spacing and bracket design before ordering. Q: Can I still remove my doors easily?A: Yes. Simply unbolt the strap from either the door or body side (one bolt) and the door functions as normal for door-off summer driving. Re-attach when you put the doors back on for the season. Q: How much door opening do these allow?A: The strap length is calibrated to the factory-designed door opening angle — approximately 75-80 degrees on most Wrangler models. This prevents over-extension while still providing full cabin access. Q: Are these better than the factory door checks?A: Yes. Factory door checks use plastic and rubber components that deteriorate from UV exposure, temperature cycling, and age. These polyester straps are inherently more durable and provide consistent, reliable door control year after year. Related Products Explore more from our full catalog. iFJF Direct offers thousands of quality replacement parts, tools, and accessories for your vehicle.

Read more less

Door Limit Strap Footman Loops for 2007-2023 Jeep Wrangler JK JL & Gladiator JT Don't let rusted footman loop brackets let your doors swing free. The iFJF Door Limit Strap Footman Loops are heavy-duty cold-forged steel replacements for the factory brackets on 2007-2023 Jeep Wrangler JK, JL, and Gladiator JT. These brackets anchor your door limit strap to the body, preventing the door from over-opening and damaging your paint, hinges, or body panels — especially critical in windy conditions or on tight trails. Black powder coated for maximum corrosion resistance, with smooth deburred edges and a complete 5-minute bolt-on installation. Includes both left and right brackets plus all mounting screws. Key Features Cold-Forged Steel: Far stronger than stamped steel factory brackets. Withstands repeated door-opening stress without bending or cracking. Black Powder Coat Finish: Maximum corrosion and rust resistance — built to outlast factory brackets that start rusting within a few seasons. 5-Minute Bolt-On Installation: Direct OE-style replacement. Remove old brackets, bolt in new ones with included screws, reattach limit strap. No drilling or modifications. Smooth Polished Edges: All edges deburred and polished for safe handling. No sharp edges to cut your hands or snag clothing during installation. Complete Kit: 2 footman loop brackets + 4 mounting screws included. Reuses Existing Straps: If your limit straps are still in good condition, you only need the brackets — no need to buy a full door check assembly. Vehicle Compatibility Year Make Model Notes 2007-2018 Jeep Wrangler JK (2-Door) All trims 2007-2018 Jeep Wrangler JKU (4-Door) All trims 2018-2023 Jeep Wrangler JL (2-Door) All trims 2018-2023 Jeep Wrangler JLU (4-Door) All trims 2020-2023 Jeep Gladiator JT All trims Specifications Specification Detail Material Cold-Forged Steel Finish Black Powder Coat Installation Bolt-On / No-Drill Installation Time ~5 Minutes Per Side Included 2 Brackets + 4 Screws Warranty 1-Year Replacement Installation Steps Open the door and locate the existing footman loop bracket on the door jamb. Remove the old bracket and mounting screws — if rusted, apply penetrating oil 5 minutes before. Align the new iFJF footman loop bracket over the factory mounting holes. Secure with the included screws — tighten firmly but do not over-torque. Reattach your existing door limit strap to the new bracket. Test door swing — full open and close to confirm strap engagement. Why Choose iFJF? iFJF footman loops are engineered for Jeep owners who demand durability beyond factory parts. Our cold-forged construction and premium powder coat finish are designed to withstand years of door cycling, UV exposure, and off-road conditions without the rust and bending issues common to OEM brackets. US-based support and fast shipping from our American warehouse. Related Products Tailgate Hinge CB Antenna & Flag Mount for JL JLU 1" Steering Wheel Hub Adapter Conversion Spacer Steering Wheel Quick Release Hub — Silver Frequently Asked Questions Q: Will these fit my 2018-2023 Wrangler JL?A: Yes. iFJF footman loop brackets are compatible with Wrangler JL and Gladiator JT in addition to the JK. These brackets have been confirmed to fit all 2007-2023 Wrangler models. Q: My factory footman loops are rusted. Can I replace just the brackets?A: Yes. This listing is for the brackets and screws only — the perfect solution if your limit straps are still in good condition but the mounting brackets are corroded or broken. Q: Do these brackets come with limit straps?A: No. This listing is for the brackets and screws only. Your existing door limit straps can be reused if they're in good condition. If your straps are also worn or torn, they'll need to be sourced separately. Q: Are these stronger than factory brackets?A: Yes. Cold-forged steel construction is significantly stronger than the stamped steel used in factory brackets. They resist bending even when a door is caught by a strong wind gust. Q: Will the powder coat rust eventually?A: The black powder coat provides excellent corrosion resistance. If the coating gets chipped during trail use, touch-up paint will prevent surface rust — just like any steel component on your Jeep. 📚 Related Guides & Articles How to install Tie Rods on your GM Truck OBS F-Series: How To Install Brake Pads & Rotor

Read more less

iFJF Door Bushing Removal Tool & Hinge Liner Rebuild Kit for Jeep Wrangler JK/JL/Gladiator JT 2007-2022 The iFJF Professional Hinge Rebuild Kit is the most comprehensive door bushing service solution in our lineup. Combining a heavy-duty stainless steel removal tool with a full set of plastic hinge liner pins, this kit gives you everything needed to completely rebuild the door hinges on your 2007-2022 Jeep Wrangler or Gladiator. Whether your doors are squeaking, rattling, sagging, or just not closing like they used to, this kit restores factory-smooth operation in a single afternoon of DIY work. Key Features Complete Hinge Rebuild Kit: One heavy-duty stainless steel removal tool plus a full set of replacement plastic hinge liner pins for a complete hinge bushing replacement. Nothing else to buy — everything needed is in the box. Fixes All Door Hinge Problems: Eliminates squeaky hinges, rattling door panels, loose/sagging doors, and difficult door closure. All symptoms trace back to worn, corroded, or swollen OE hinge bushings that this kit is designed to replace. Reusable Stainless Steel Tool: The removal tool is built from rugged stainless steel for long-term durability. Use it on your Jeep today, loan it to a friend tomorrow, and use it again in 5 years — the tool maintains its shape and function through repeated use. Updated 2007-2022 Coverage: This version of the kit extends compatibility through the 2022 model year, covering the latest JL and Gladiator JT models. The hinge design remained consistent, so the tool works across all years. Simple Hammer Installation: No press, no special tools, no mechanic required. Align the tool, tap with a standard hammer to drive out the old bushing, tap in the new plastic liner pin with a rubber mallet. It's that straightforward. 2-Year iFJF Warranty: Built to professional standards and backed by our quality guarantee. Vehicle Fitment Jeep Wrangler JK (2007-2018): 2-door, all trims Jeep Wrangler JKU (2007-2018): 4-door, all trims Jeep Wrangler JL (2018-2022): 2-door, all trims Jeep Wrangler JLU (2018-2022): 4-door, all trims Jeep Gladiator JT (2020-2022): All trims NOT compatible: TJ (1997-2006), YJ (1987-1995), or CJ models Installation Guide Remove Door Hinge Pins: Safely support the door (or have a helper hold it). Remove the hinge pins — note which position each pin came from. Drive Out Old Bushings: Place the iFJF removal tool over the top of each hinge. Tap firmly with a hammer until the OE liner pins are fully driven out of the hinge bore. Clean Hinge Bores: Remove all rust and debris from the hinge bores using a wire brush. Apply a light coat of grease or lubricant to the clean bore. Install New Liner Pins: Tap the new plastic hinge liner pins into each hinge bore using a rubber mallet. Ensure they are fully and evenly seated. Reinstall the Door: Rehang the door and reinsert hinge pins. Test for smooth, rattle-free operation. Protect Your Paint: Always place a shop towel, piece of cardboard, or rubber mat under the hinge area before hammering. A few seconds of protection prevents an accidental hammer slip from chipping your paint. The Real Cost of Ignoring Worn Hinge Bushings Door hinge bushings might seem like a minor, cosmetic issue, but ignoring them can lead to real problems. When bushings wear out, the door's weight shifts from the bushing surface to the steel hinge pin riding directly against the steel hinge bore — metal on metal. This accelerates wear on the hinge assembly itself, an expensive component to replace. A sagging door can also stress the door latch and striker, causing alignment issues that make the door difficult to close or, worse, prevent it from latching securely. Addressing worn bushings early with this kit protects your Jeep's more expensive components and ensures your doors close properly every time. Package Includes 1 × Stainless Steel Door Bushing Removal Tool Complete Set of Plastic Hinge Liner Pins Installation Guide Frequently Asked Questions Will this work on a 2023 Gladiator JT? The kit covers 2007-2022 models. While hinge design has been consistent, we recommend contacting our support team to verify fitment for 2023+ model years before purchasing. Do I need a professional to install this? No. This is a straightforward DIY job. Most owners complete the installation in 30-45 minutes with basic hand tools and a hammer. No mechanical experience or special skills required. Are the replacement liner pins the same material as OEM? The replacement liner pins are made from durable, OE-equivalent plastic material designed to provide the same fit, feel, and wear characteristics as the factory bushings. They are not metal, which is intentional — plastic bushings prevent metal-on-metal contact and allow for smooth door operation. Can I use this to service all 4 doors on my JKU? Yes. The tool works on every hinge across all doors. For a 4-door JKU or JLU, simply repeat the process for each door. The tool is designed for repeated use and will not wear out. 🔗 You May Also Like iFJF Door Bushing Removal Tool Hinge Liners for Wrangler JK JKU JL JLU Glad iFJF 2pcs Door Bushing Removal Tool Hinge Liners for Wrangler JK JKU JL JLU iFJF Door Bushing Removal Tool Hinge Liners for Wrangler JK JKU JL JLU Glad iFJF Door Hinge Nuts for Wrangler JK JKU 2007-2017 (DR-8) 📖 Related Installation Guides & Articles 📝 Ball joint removal/install on 2018 ram 4500/5500 diesel. 📝 How to Install a Bluetooth Kill Switch: Anti-Theft Battery Disconnect Guide 📝 Why You Need a Bluetooth Kill Switch for Your RV or Truck

Read more less

iFJF Complete Door Hinge Service Kit with Alignment Pins for Jeep Wrangler JK/JL/Gladiator JT 2007-2021 The iFJF Complete Door Hinge Service Kit is our most comprehensive offering — the ultimate solution for Jeep owners who want to do the job once and do it right. This kit includes a professional-grade stainless steel removal tool, 8 plastic hinge liner pins for a full hinge rebuild, and 4 precision alignment pins that make door reinstallation effortless. If you've ever struggled to line up a Jeep door during reinstallation, the alignment pins alone are worth the price of admission. Everything you need for a complete, professional-quality hinge rebuild — in one box. Key Features Everything in One Kit: 1 stainless removal tool + 8 plastic hinge liner pins + 4 precision alignment pins. This is the complete package — no additional tools or parts required. Service all 4 door hinges (upper/lower × left/right) and rehang your doors with perfect alignment. 4 Precision Alignment Pins: The game-changer feature of this kit. These tapered alignment pins screw into the hinge bores before you hang the door, guiding it into perfect position. No more wrestling with a heavy door while trying to line up hinge pin holes — the alignment pins do the work for you. Eliminates Squeaks, Rattles & Hard Closing: Removes corroded OE liner pins and replaces them with fresh components. Restores smooth, quiet, effortless door operation across all road and trail conditions. Professional-Grade Stainless Tool: The removal tool is built from heavy-duty stainless steel for durability. The hinge liner pins are plastic — deliberately — to prevent metal-on-metal contact that would wear out the hinge bores. Complete 5-Step Process: Remove old bushings → clean bores → install new liners → use alignment pins to hang doors → test operation. The entire job is designed to be completed in a driveway with basic tools. 2-Year iFJF Warranty: Backed by our quality assurance and US-based customer support. Vehicle Fitment Jeep Wrangler JK (2007-2018): 2-door, all trims Jeep Wrangler JKU (2007-2018): 4-door, all trims Jeep Wrangler JL (2018-2021): 2-door, all trims Jeep Wrangler JLU (2018-2021): 4-door, all trims Jeep Gladiator JT (2020-2021): All trims NOT compatible: TJ (1997-2006), YJ (1987-1995), CJ models Installation Guide Support & Remove Doors: Support the door (helper or floor jack with padding). Remove the hinge pins. Keep track of pin positions for reinstallation. Drive Out Old Bushings: Align the iFJF removal tool at the top of each hinge. Tap firmly with a hammer until the OE liner pins are fully driven out of the hinge bore — repeat for all 4 hinges. Clean & Lubricate: Remove all rust and debris from each hinge bore with a wire brush. Apply a light coat of grease or anti-seize lubricant to the clean bore surfaces. Install New Hinge Liner Pins: Tap the new plastic liner pins into each hinge bore using a rubber mallet. Verify each pin is fully and evenly seated. Install Alignment Pins: Thread the 4 precision alignment pins into the hinge bores. These provide a tapered guide surface for hanging the door. Hang the Door: Slide the door onto the alignment pins — the tapered design guides it into perfect position. Once aligned, remove the alignment pins and reinsert the original hinge pins. Test & Enjoy: Open and close the door several times to verify smooth, quiet, rattle-free operation. Pro Tip: The alignment pins are the secret to a frustration-free door reinstallation. Even if you've done this job before, the alignment pins save 15-20 minutes of trial-and-error positioning. Don't skip this step. Why Alignment Pins Matter Anyone who has removed and reinstalled Jeep doors knows the hardest part isn't getting the old bushings out — it's getting the doors back on. Jeep doors are heavy (60-80 lbs for a JK front door), awkwardly shaped, and must align precisely with two small hinge bores simultaneously. Without alignment pins, you're holding up a heavy door with one hand while trying to find the invisible hinge hole with the other. The alignment pins in this kit thread into the hinge bores first, providing a tapered guide that lets you simply slide the door into position. Once aligned, you remove the pins and reinsert the factory hinge pins. This feature alone makes the Complete Kit worth the upgrade over a basic tool-only or liner-only kit. Package Includes 1 × Stainless Steel Door Bushing Removal Tool 8 × Plastic Hinge Liner Pins (for all 4 hinge positions) 4 × Precision Alignment Pins Installation Guide Frequently Asked Questions Will this kit work on a 2022-2023 Wrangler JL? The kit is specified for 2007-2021 models. While the hinge design has remained consistent through 2023, we recommend contacting our support team to verify fitment for 2022+ model years before ordering. My doors are very hard to close. Will this fix it? Yes. Worn, swollen, or corroded hinge bushings are the leading cause of difficult door closure on JK and JL Wranglers. This kit replaces all worn hinge components for a complete restoration of factory door operation. Does this kit include hinge nuts? No. Door hinge nuts are sold separately. This kit includes the removal tool, hinge liner pins, and alignment pins — everything needed for the bushing replacement and door reinstallation process. Can I install this by myself without a helper? The alignment pins significantly simplify solo installation. You'll still need a way to support the door's weight during removal and reinstallation — a floor jack with a padded block works well. Many owners complete the entire job solo using the alignment pins for door hanging. Are the alignment pins reusable? Yes. The alignment pins are made from durable steel and can be reused every time you remove and reinstall your doors. Keep them in your tool kit for trail-side door removal or seasonal door swaps. 🔗 You May Also Like iFJF Door Bushing Removal Tool Hinge Liners for Wrangler JK JKU JL JLU Glad iFJF 2pcs Door Bushing Removal Tool Hinge Liners for Wrangler JK JKU JL JLU iFJF Door Bushing Removal Tool Hinge Liners for Wrangler JK JKU JL JLU Glad iFJF Door Hinge Nuts for Wrangler JK JKU 2007-2017 (DR-8) 📖 Related Installation Guides & Articles 📝 Ball joint removal/install on 2018 ram 4500/5500 diesel. 📝 How to Install a Bluetooth Kill Switch: Anti-Theft Battery Disconnect Guide 📝 Why You Need a Bluetooth Kill Switch for Your RV or Truck

Read more less

iFJF Door Bushing Removal Tool & Hinge Liners for Jeep Wrangler JK/JL/Gladiator JT 2007-2021 The iFJF Door Bushing Removal Tool is the do-it-yourself solution every Jeep Wrangler owner needs. Over time, the factory door hinge bushings on the JK, JL, and Gladiator JT corrode, wear down, and cause the doors to squeak, rattle, and become difficult to close. This professional-grade stainless steel removal tool lets you extract those worn OE bushings and install fresh hinge liner pins — all in your driveway with basic tools. No trip to the dealer, no expensive shop labor, no need to live with doors that don't close right. Key Features Professional-Grade Stainless Steel Tool: Precision-machined from high-grade stainless steel for durability and repeated use. Designed to withstand the hammer impact needed to drive out corroded, seized OE bushings without deforming or mushrooming. Fixes Squeaky & Hard-to-Close Doors: Worn hinge bushings are the #1 cause of door squeaks, rattles, and stiff operation on Jeep Wranglers. This tool makes bushing replacement a straightforward at-home job — no mechanic needed. Complete Bushing Replacement Kit: Includes the removal tool plus replacement hinge liner pins. Remove the old, tap in the new — your doors operate like factory-fresh. Universal JK/JL/JT Compatibility: Works on all 2007-2021 Jeep Wrangler JK (2-door & 4-door), JL (2-door & 4-door), and 2020-2021 Gladiator JT models. One tool covers the entire modern Wrangler family. Simple Hammer Installation: No press, no special tools, no mechanical experience required. Align the tool over the hinge, tap with a standard hammer, and the old bushing drives out in seconds. 2-Year iFJF Warranty: Built to last and backed by our quality guarantee. Vehicle Fitment Jeep Wrangler JK / JKU (2007-2018): 2-door & 4-door models, all trim levels Jeep Wrangler JL / JLU (2018-2021): 2-door & 4-door models, all trim levels Jeep Gladiator JT (2020-2021): All trim levels NOT compatible with: Jeep Wrangler TJ (1997-2006), YJ (1987-1995), CJ models Installation Guide Support the Door: Open the door and place support under it, or have a helper hold it. Remove the existing hinge pins. Position the Removal Tool: Place the iFJF removal tool at the top of the hinge, aligned with the OE bushing. Tap Firmly: Strike the tool with a standard hammer until the OE bushing is fully driven out of the hinge bore. Clean the Hinge Bore: Remove any rust, debris, or corrosion from the hinge bore. Apply a light coat of grease or lubricant. Install New Bushings: Tap the new hinge liner pins into place using a rubber mallet or hammer with a block of wood to prevent damage. Reinstall the Door: Align and reinstall the door. Test for smooth, quiet, rattle-free operation. Pro Tip: Place a piece of cardboard or a shop towel under the hinge before hammering to protect your vehicle's paint. Why Your Jeep Doors Rattle — And How This Tool Fixes It Jeep Wranglers are designed with removable doors, which means the hinge system uses plastic liner bushings between the steel hinge pin and the steel hinge bore. These bushings are consumable — they wear down from thousands of door open/close cycles and the constant vibration of off-road driving. Worse, moisture and road salt can corrode the OE bushings, causing them to swell and seize. The result: doors that creak and groan with every movement, rattle over bumps, and require a shoulder-shove to close properly. This iFJF tool removes those damaged bushings in minutes, allowing you to install fresh hinge liners that restore the factory door feel. It's one of the highest-impact, lowest-cost maintenance items you can do on a JK or JL. Package Includes 1 × Stainless Steel Door Bushing Removal Tool Replacement Hinge Liner Pins Installation Guide Frequently Asked Questions My doors rattle on rough roads. Will this fix it? Yes. Worn or corroded door hinge bushings are the primary cause of door rattling on JK and JL Wranglers. Replacing these bushings with this tool and fresh liner pins typically eliminates the rattle completely. Do I need a mechanic for installation? No. This is a straightforward at-home job. Most owners complete it in under an hour with basic hand tools and a hammer. No special skills required — just follow the step-by-step guide above. Will this work on a Gladiator JT? Yes. This kit is fully compatible with the 2020-2021 Jeep Gladiator JT, which shares the same door hinge design as the JL Wrangler. Will this fit a 2022 or newer model? The kit is specified for 2007-2021. While the hinge design has not changed significantly, we recommend verifying compatibility with your specific model year. Contact our support team if you have a 2022+ model. Can I reuse the tool on multiple Jeeps? Absolutely. The stainless steel construction is designed for repeated use. Many owners use this tool to service doors across multiple Jeeps in their household or club. 🔗 You May Also Like iFJF 2pcs Door Bushing Removal Tool Hinge Liners for Wrangler JK JKU JL JLU iFJF Door Bushing Removal Tool Hinge Liners for Wrangler JK JKU JL JLU Glad iFJF Door Bushing Removal Tool Hinge Liners for Wrangler JK JKU JL JLU Glad iFJF Door Hinge Nuts for Wrangler JK JKU 2007-2017 (DR-8) 📖 Related Installation Guides & Articles 📝 Ball joint removal/install on 2018 ram 4500/5500 diesel. 📝 How to Install a Bluetooth Kill Switch: Anti-Theft Battery Disconnect Guide 📝 Why You Need a Bluetooth Kill Switch for Your RV or Truck

Read more less

Product Overview The iFJF Car Rear Seat Isolation Barrier Net Back Pet Dog Seat Divider for Wrangler JK JL Unlimited 2 Door 4 Door for Pet Children Safe Drive from iFJF is a precision-engineered aftermarket upgrade designed to deliver exceptional performance, durability, and value. Crafted from premium-grade materials, this interior accessory combines practical functionality with sleek aesthetics. Designed specifically for your vehicle, it provides a seamless OEM-quality fit while enhancing comfort, convenience, and organization. Vehicle Compatibility This product is designed for the following vehicles: Please verify compatibility with your specific vehicle year, make, model, and engine configuration before purchasing. Contact our support team if you need assistance confirming fitment for your application. Note: Professional installation is recommended. Verify fitment for your specific sub-model, cab configuration, and drivetrain (2WD/4WD) before ordering. Key Features Premium-Grade Materials: High-quality ABS plastic, carbon fiber pattern, or durable nylon construction Custom Vehicle-Specific Fit: Precision-molded to match your vehicle's interior contours exactly Easy Installation: No drilling or permanent modifications — installs in minutes with basic tools Enhanced Interior Aesthetics: Upgrades the look and feel of your cabin Practical Functionality: Adds storage, organization, or protection to high-wear areas Technical Specifications Specification Details Construction High-strength nylon with excellent wear and heat resistance Adjustable Fit: 4 adjustable straps ensure secure installation for different vehicle configurations Tool-Free Install: No drilling or cutting required - installs in minutes with included hooks Easy Maintenance: Removable design allows for easy cleaning Compatibility Jeep Wrangler JK/JKU (2007-2018) - 2 Door & 4 Door Jeep Wrangler JL/JLU (2018-2021) - 2 Door & 4 Door Installation Steps Position barrier between front and rear seats Attach side hooks to roll bar or seat mounts Secure bottom straps to seat anchors Adjust tension for optimal fit Package Includes 1 × Rear Seat Isolation Barrier Net 4 × Adjustable Mounting Straps 4 × Installation Hooks FAQ Q: Can this be used with car seats? A: Yes, the barrier can be installed alongside child car seats. Ensure proper clearance before installation. Q: Is it compatible with both 2-door and 4-door Wrangler? A: Yes, the adjustable design fits both 2-door and 4-door models. Brand iFJF Condition New Warranty Contact iFJF Support for warranty details Installation Guide Clean Surface: Wipe the installation area thoroughly with isopropyl alcohol to remove all dirt and oils. Dry Fit: Test-fit the accessory before removing any adhesive backing to confirm alignment. Apply: Peel adhesive backing and carefully position the accessory. Press firmly for 30-60 seconds across the entire surface. Cure: Allow adhesive to cure for 24 hours before exposure to moisture or extreme temperatures. Recommended: Professional installation is always recommended for optimal results. Installation time varies by vehicle and experience level — typically 1-3 hours. Frequently Asked Questions Q: Does this come with installation hardware? A: Yes. The kit includes all necessary gaskets, bolts, nuts, and mounting hardware required for a complete installation. Q: Is professional tuning required after installation? A: For most applications, no tuning is required for basic operation. Contact our support team for vehicle-specific recommendations. Q: What is the warranty on this product? A: iFJF stands behind all products with comprehensive warranty coverage. Please contact our customer service team for specific warranty terms and conditions applicable to this product. Q: How long does shipping take? A: Most orders ship within 1-2 business days. Delivery times depend on your location and selected shipping method. You'll receive tracking information as soon as your order ships. Why Choose iFJF? Quality You Can Trust: Every iFJF product is manufactured to rigorous quality standards using premium materials and advanced production techniques. We don't cut corners — we engineer parts that perform and last. Direct-Fit Engineering: Our products are designed using precision CAD/CAM technology and verified against OEM specifications, ensuring a hassle-free installation that fits right the first time. Performance Proven: From daily drivers to track machines, iFJF parts deliver measurable improvements in horsepower, torque, throttle response, and overall driving experience. Exceptional Value: We offer premium-quality parts at competitive prices, giving you the best performance-per-dollar in the aftermarket industry. Dedicated Support: Our knowledgeable team is here to help — before, during, and after your purchase. Questions about fitment, installation, or performance? We've got answers. Fast, Reliable Shipping: We process and ship orders quickly from our US warehouses, so you spend less time waiting and more time enjoying your upgraded vehicle. Related Products Complete your build with these complementary iFJF products: All-Weather Floor Mats — Protect your interior with custom-fit durable floor liners Center Console Organizer Tray — Add even more storage and organization to your vehicle Seat Back Protector — Shield your seats from cargo, pets, and daily wear

Read more less

Restore Your JL's Clean Front-End Look Is your Jeep Wrangler JL's antenna base cover cracked, faded, or missing? The factory ABS cover on the cowl panel is exposed to sun, road debris, and car wash brushes. The iFJF Antenna Base Cover is a direct-fit replacement that snaps into place in minutes. Key Features Perfect OEM-Style Fit: Precision-molded to match the factory contour exactly. Snaps securely into factory mounting points with zero gaps or rattles. Durable Black ABS: High-impact ABS plastic resists cracking, warping, and UV fading for years of service. 5-Minute Snap-On Install: No tools, no adhesive — simply align the tabs and press into place. UV-Resistant Finish: Matte black with UV stabilizers prevents the chalky, faded look of cheap covers. Compatibility Make Model Year Range Jeep Wrangler JL/JLU 2018-2022 Jeep Gladiator JT 2020-2022 Common Issues with Factory Covers Cracking: Factory cover cracks after 2-3 years of heat cycling and UV exposure. Fading: Original cover turns chalky gray, making your JL look older. Missing: Car washes and trail branches dislodge loose covers. Water Ingress: A cracked cover allows water to seep into the antenna base, causing corrosion. Specifications Spec Detail Material High-Impact ABS Plastic Finish Matte Black, UV-Stabilized Installation Snap-on, Tool-free, <5 min Frequently Asked Questions Q: Does this include the antenna itself?A: No. This is the base cover only — the plastic trim surrounding the antenna base on the cowl panel. Q: Will this fit with an aftermarket antenna?A: Yes, as long as your aftermarket antenna uses the factory base mounting location. Q: OEM vs aftermarket?A: Manufactured to the same specifications as the OEM Mopar part at a fraction of the dealer price. Q: Will this fit 2023+ JL?A: The 2018-2022 cowl panel design was carried over in most cases. Compare your cowl shape to images. Q: Other colors available?A: Currently matte black only, matching all JL/JT factory trim. Can be painted for custom schemes.

Read more less

6PCS Torx Screw Bolt Kit for 2018-2020 Jeep Wrangler JL / JLU Replace your worn, stripped, or lost Torx hardware with this premium 6-piece stainless steel bolt kit. Designed specifically for the 2018-2020 Jeep Wrangler JL (2-door and 4-door JLU), these OEM-spec T40 Torx screws fit the windshield frame, windshield hinges, full/half door hinges, and roll bar mounts. Whether you're refitting after a windshield fold-down, doing a door-off summer setup, or replacing corroded factory fasteners, this kit has you covered. Key Features Premium Stainless Steel Construction: Corrosion-resistant 304 stainless steel — far more durable than factory carbon steel bolts that rust after one winter season. Exact OEM Specification: T40 Torx drive with identical thread pitch, length, and shoulder dimensions to factory hardware. No modification required. Complete 6-Piece Set: Includes all Torx bolts needed for windshield frame hinges, door hinges, and roll bar attachments — one kit covers multiple locations. Anti-Seize Pre-Treatment: Bolts ship with a light anti-seize coating to prevent galling and make future removal effortless. Made for Door-Off Lifestyle: Frequent JL owners who run doorless know factory bolts round out fast. These stainless replacements provide years of on/off cycles. Compatibility Vehicle Year Range Locations Jeep Wrangler JL (2-Door) 2018–2020 Windshield frame · Windshield hinges · Full/Half door hinges · Roll bar Jeep Wrangler JLU (4-Door) 2018–2020 Windshield frame · Windshield hinges · Full/Half door hinges · Roll bar Note: These are T40 Torx screws specifically for hinge and frame mounting points — not the smaller windshield-to-cowl bolts (those use T30). Verify your bolt size before ordering. Specifications Specification Value Material 304 Stainless Steel Drive Type T40 Torx Quantity 6 pieces Thread Type Metric — OEM match Corrosion Resistance Grade 304 — salt spray tested Finish Natural stainless (silver) Applications Windshield frame, door hinges, roll bar Why Choose iFJF Factory JL Torx bolts are carbon steel with a thin zinc coating — one Midwest winter and they're rusted solid. Our 304 stainless replacements eliminate this headache permanently. Each bolt is CNC-machined to exacting tolerances and pre-treated with anti-seize for smooth installation. iFJF stands behind every fastener with a satisfaction guarantee. When you're tired of PB Blaster and stripped Torx heads, upgrade to stainless. Frequently Asked Questions Q: Will these fit my 2021+ Jeep Wrangler JL?A: Jeep made minor revisions to some hinge bolt specifications for 2021+. While many customers report successful fitment on 2021+ models, we officially guarantee fitment for 2018-2020 JL/JLU only. Measure your existing bolt before ordering for 2021+ vehicles. Q: Do I need a T40 bit to install these?A: Yes, a T40 Torx bit (or Torx socket) is required. A standard T40 bit in a 3/8" ratchet or impact driver works best. Do NOT use a T45 or Allen key — you'll round the drive. Q: Can I use an impact driver?A: Hand-tightening with a ratchet is recommended for windshield hinge bolts to avoid stripping the body threads. Door hinge bolts can be run in with an impact driver on low torque setting, but final tighten by hand to 18-22 ft-lbs. Q: Why do factory bolts rust so quickly?A: OEM JL bolts are carbon steel with a thin electroplated zinc coating. Once the coating scratches during the first removal, bare steel is exposed. Road salt, humidity, and car washes accelerate corrosion. Stainless steel doesn't have this problem. Q: Do these come with the nylon locking patch like OEM?A: These are smooth-thread bolts — the nylon locking patch is not applied. Factory nylon patches wear off after 2-3 removal cycles anyway. For vibration resistance, apply a small drop of blue Loctite (242) to the threads before installation. Q: Can I use these for the hardtop mounting bolts?A: No. Hardtop mounting bolts use a different thread pitch and length. This kit is specifically for windshield hinges, door hinges, and roll bar hardware. Hardtop hardware is sold separately. Related Products Rear License Plate Relocation Bracket — Clean up your rear end Bottle Opener License Plate Delete Cover — Fun JK accessory Spare Tire Trash Bag — Keep your Jeep clean on the trail

Read more less

iFJF 2-Piece Door Bushing Removal Tool & Hinge Liner Set for Jeep Wrangler JK/JL/Gladiator JT 2007-2021 The iFJF 2-Piece Door Bushing Removal Tool Set is the complete solution for servicing both sides of your Jeep Wrangler or Gladiator. Instead of buying a single tool and working one door at a time, this kit includes two professional-grade stainless steel removal tools — one for the driver side, one for the passenger side — plus replacement hinge liner pins. Service both doors in a single session and restore factory-smooth operation to every hinge on your Jeep. Key Features 2-Piece Set — Both Doors Covered: Includes two stainless steel removal tools plus hinge liner pins. Service upper and lower hinges on both driver and passenger doors in one complete session. No need to buy additional tools or pins separately. Heavy-Duty Stainless Steel Construction: Both removal tools are machined from high-grade stainless steel that withstands repeated hammer impacts without deforming. Built for years of use — service your own Jeep today and help a friend with theirs tomorrow. Fixes All Common Door Problems: Addresses squeaky hinges, rattling door panels, loose-fitting doors, and difficult-to-close doors. All symptoms of worn, corroded, or swollen OE door hinge bushings. Simple Hammer Installation: Align the tool at the top of the hinge, tap firmly with a standard hammer, and drive out the old bushing. Install the new liner pin with a rubber mallet. No press, no special tools, no mechanic experience needed. Broad Vehicle Compatibility: Works across the entire modern Wrangler platform — JK, JKU, JL, JLU, and Gladiator JT from 2007 through 2021. 2-Year iFJF Warranty: Quality guaranteed. If anything goes wrong, we'll make it right. Vehicle Fitment Jeep Wrangler JK (2007-2018): 2-door, all trims Jeep Wrangler JKU (2007-2018): 4-door, all trims Jeep Wrangler JL (2018-2021): 2-door, all trims Jeep Wrangler JLU (2018-2021): 4-door, all trims Jeep Gladiator JT (2020-2021): All trims NOT compatible: TJ (1997-2006), YJ (1987-1995), or any pre-JK models Installation Guide Support Both Doors: Open each door and place support underneath. Remove the hinge pins from both doors — keep track of which pin goes where. Remove Old Bushings: For each hinge (4 total: upper/lower × left/right), place the iFJF removal tool at the top of the hinge and tap with a hammer until the OE bushing is fully driven out. Clean Hinge Bores: Remove all rust, debris, and corrosion from each hinge bore. A wire brush and brake cleaner work well. Apply a light coat of grease or anti-seize lubricant. Install New Hinge Liner Pins: Tap the fresh plastic hinge liner pins into place using a rubber mallet. Ensure they seat fully and evenly in each bore. Reinstall Doors: Rehang both doors and reinsert the hinge pins. Test each door for smooth operation — they should open and close effortlessly with no squeaks or rattles. Pro Tip: Mark each door's hinge pin position before removal (e.g., "DS-Upper") to ensure correct reinstallation. Protect your paint with a shop towel or cardboard under the hinge during hammering. Why Two Tools Beat One If you're servicing worn door bushings, the odds are high that both sides need attention. Door bushings wear at roughly the same rate, and corrosion doesn't pick favorites. Having two removal tools in one kit means you can complete the entire job — all four hinges — without sharing a single tool between sides. It also means you have a backup tool for future service or for helping a fellow Jeep owner in your off-road group. The value of a complete 2-tool kit versus buying two separate single-tool kits is significant, and you get everything you need in one box. Package Includes 2 × Stainless Steel Door Bushing Removal Tools Complete Set of Hinge Liner Pins (for both doors) Installation Guide Frequently Asked Questions Does this kit include alignment pins? No. This kit includes 2 removal tools and replacement hinge liner pins. If you need alignment pins for precise door reinstallation, those are available separately in our complete hinge service kit (FJ-JP-DR-GE-ZH4). Will this work on the 4-door JKU and JLU? Yes. The removal tools work identically on 2-door and 4-door configurations for both the JK and JL platforms. The hinge design is consistent across all body styles. Can I use this on a 2022-2023 model? The listing specifies 2007-2021 compatibility. While the hinge design has remained consistent, we recommend contacting our support team to verify fitment for 2022+ model years before purchasing. How long does a full 2-door service take? Most owners complete the full service (all 4 hinges, both doors) in 45-60 minutes. Heavily corroded bushings may require more hammer time, but the stainless steel tool is built to handle it. 🔗 You May Also Like iFJF Door Bushing Removal Tool Hinge Liners for Wrangler JK JKU JL JLU Glad iFJF Door Bushing Removal Tool Hinge Liners for Wrangler JK JKU JL JLU Glad iFJF Door Bushing Removal Tool Hinge Liners for Wrangler JK JKU JL JLU Glad iFJF Door Hinge Nuts for Wrangler JK JKU 2007-2017 (DR-8) 📖 Related Installation Guides & Articles 📝 Ball joint removal/install on 2018 ram 4500/5500 diesel. 📝 How to Install a Bluetooth Kill Switch: Anti-Theft Battery Disconnect Guide 📝 Why You Need a Bluetooth Kill Switch for Your RV or Truck

Read more less

Axle-Back Catback Exhaust for 2007-2023 Jeep Wrangler JL & JK — 2.0L Turbo & 3.6L Pentastar Transform the sound and presence of your Jeep Wrangler with this premium stainless steel axle-back exhaust system. Designed as a direct bolt-on for both the 2007-2018 JK (3.6L Pentastar) and 2018-2023 JL (2.0L turbo & 3.6L Pentastar), this dual outlet catback delivers a deep, throaty exhaust note without the drone that makes budget systems unbearable at highway speeds. The larger-diameter mandrel-bent tubing reduces backpressure for improved throttle response, while the dual polished tips complete the aggressive rear-end look. Key Features Dual Outlet Design: Twin polished exhaust tips exit symmetrically for an aggressive, balanced rear profile that fills the factory bumper cutouts perfectly. Deep Tone — Zero Drone: Carefully tuned chamber design delivers a deep, muscular sound at idle and acceleration while remaining civilized at cruise RPM (1,800-2,200) — no headache-inducing drone. Mandrel-Bent Tubing: Constant-diameter bends maintain exhaust velocity without the crimps and pinch points found in crush-bent factory pipes. Stainless Steel Construction: Corrosion-resistant stainless handles winter road salt, beach sand, and trail mud without rusting through like aluminized steel alternatives. Direct Bolt-On Install: Uses factory exhaust hanger locations and connection points — no cutting, welding, or fabrication. Basic hand tools and 45 minutes in the driveway. Cross-Platform Compatibility: Same kit fits both JK and JL generations — upgrade now and keep this exhaust if you trade up to a newer Wrangler. Compatibility Make Model Engine Years Doors Jeep Wrangler JK / JKU 3.6L Pentastar V6 2007–2018 2-Door & 4-Door Jeep Wrangler JL / JLU 2.0L Turbo I4 2018–2023 2-Door & 4-Door Jeep Wrangler JL / JLU 3.6L Pentastar V6 2018–2023 2-Door & 4-Door Note: Does NOT fit 4xe (PHEV) models — the hybrid battery packaging interferes with the exhaust routing. Does NOT fit 392 V8 models. For 2-door models, the system may require trimming of the intermediate pipe for proper fitment (instructions included). Specifications Specification Value Material Stainless Steel System Type Axle-Back (from axle to tips) Outlet Style Dual (left and right) Tip Finish Polished stainless Tip Diameter 4.0" (102mm) each Pipe Diameter 2.5" (63mm) mandrel-bent Sound Level Moderate-aggressive (no drone at cruise) Installation Time Approx. 45-60 minutes Why Choose iFJF The Wrangler's factory exhaust is designed for silence, not presence — and the aftermarket is full of systems that are either too quiet to justify the cost or so loud they ruin the daily driving experience. iFJF engineered this axle-back to hit the sweet spot: a deep, commanding tone that announces your arrival without punishing you on the highway. Our dual outlet design fills the bumper cutouts for a factory-finish look, and the stainless construction means it'll outlast your Wrangler. If you want your Jeep to sound like it looks, this is the exhaust. Frequently Asked Questions Q: How loud is this compared to stock?A: Noticeably louder but not obnoxious. At cold start, you'll hear a deep, throaty burble — about 30% louder than stock. At wide-open throttle, it's aggressive and makes the 3.6L V6 sound genuinely good (a feat few exhausts achieve). At 70 mph cruise, cabin noise increase is minimal — you can still hold a conversation or listen to music without raising your voice. Q: Will this drone on the highway?A: No — that's the key advantage of this design. The chambered muffler is tuned to cancel the 120-140Hz drone frequency that occurs at 1,800-2,200 RPM (typical JK/JL highway RPM with 3.21-4.10 gears). If you've ever ridden in a Jeep with a cheap muffler delete, you know exactly what drone is — this system eliminates it. Q: Does this fit the 2-door Wrangler?A: Yes, with modification. The intermediate pipe length is designed for the 4-door (Unlimited) wheelbase. On 2-door models, the intermediate pipe needs to be trimmed by approximately 4 inches. Detailed instructions with measurements are included. Q: Will I lose low-end torque with a free-flowing exhaust?A: No. The axle-back section is downstream of the catalytic converters and resonators — it primarily affects sound, not backpressure. Unlike a full header-to-tip system, an axle-back change does not impact exhaust scavenging or low-end torque. Q: Is this compatible with aftermarket bumpers?A: Most aftermarket bumpers with factory-style exhaust cutouts will fit fine. Full-width plate bumpers without cutouts may require the tips to exit below the bumper. Test fitment before final tightening. Q: Can I install this without lifting the Jeep?A: Yes — the axle-back sits behind the rear axle, so standard ride height provides enough clearance to work underneath. Jack stands are recommended for safety but not required. A 15mm socket, penetrating oil on the factory clamp, and a rubber hanger removal tool are the only special items you'll need. Related Products Exhaust Headers for Wrangler JK 3.8L & Mustang 3.8L — Complete the system from head to tailpipe Long Tube Headers for Ram 1500 HEMI — V8 performance headers Spare Tire Trash Bag — Jeep off-road storage

Read more less

Product Overview Protect your JK or JL Wrangler's most critical safety systems with the iFJF Front Brake Line Anchor Bracket (#1101255) in Red. When you lift your Wrangler, factory brake line routing puts hoses and ABS sensor wires dangerously close to the tire's path. This bracket relocates both to a secure, protected position — preventing the pinched, cut, or snapped lines that cause complete brake failure. The bold red finish matches popular aftermarket suspension components for a custom, color-coordinated engine bay. Key Features Relocates Brake Lines & ABS Sensor Wiring — Secures both front brake hoses and wheel speed sensor wires away from the tire contact zone. Prevents Trail-Stopping Failures — Cut brake line = zero brakes. Damaged ABS sensor = disabled stability control. This bracket prevents both. Fits JK (2007-2018) & JL (2018-2023) — Covers entire JK/JL generation across all trims. 2-door and 4-door compatible. Steel with Red Finish — Laser-cut steel construction won't bend. Red powder coat adds visual pop and corrosion resistance. Essential Lifted Jeep Protection — Restores safe brake line routing regardless of lift height or tire size. Compatibility Make Model Years Jeep Wrangler JK (2 & 4 Door) 2007-2018 Jeep Wrangler JL (2 & 4 Door) 2018-2023 Specifications Specification Detail Part Reference 1101255 Material Laser-cut steel Finish Red powder coat Fitment Front left & right SKU FJ-JP-BC02-RD Frequently Asked Questions Q: Black vs Red?A: Same bracket — Red matches red suspension components, Black for stealth OEM+ look. Q: One bracket per side?A: Sold individually. Most order 2 for complete front protection. Q: Cutting/welding needed?A: Zero — uses existing factory bolt holes. Remove bolt, position bracket, reinstall bolt. Q: Needed if stock height?A: Factory-height usually has adequate clearance, but oversized tires on stock suspension can still create tight clearances. Q: Risk of not relocating?A: Lines rub tire sidewall until jacket wears through. At worst, sharp turn at full compression snaps the line — instant brake failure. Related Products Brake Line Anchor Bracket — JK/JL Extended Brake Lines — JK 4-6" Lift Extended Brake Lines — XJ/YJ/TJ Related Blog Posts iFJF Guides — Installation & Maintenance Jeep Wrangler Lift Kit Buyer's Guide

Read more less

Product Overview One of the most common failures on lifted JKs and JLs isn't engine or drivetrain related — it's a pinched, cut, or snapped brake line from tire contact during articulation. The iFJF Front Brake Line Anchor Bracket (#1101255) solves this by securely relocating both front brake lines and ABS wheel speed sensor wiring away from the tire envelope. Laser-cut from ABS-grade steel with a durable black finish, this bracket is a must-have for any lifted JK or JL that sees off-road use. Key Features Relocates Brake Lines & ABS Sensor Wiring — Moves both the front brake hose AND wheel speed sensor wire to a safe position, preventing tire contact during full-lock turns and compression. Prevents Catastrophic Failures — A pinched brake line can burst (zero brakes). A cut ABS sensor disables traction control. This bracket prevents both scenarios. Fits 2007-2023 JK & JL — Covers all 2-door and 4-door Wrangler JK (2007-2018) and JL (2018-2023) models. Uses factory mounting points — no drilling. ABS-Grade Steel, Black Finish — Laser-cut steel won't bend under stress. Black finish resists rust and impact damage. Essential for Lifted Jeeps — Lift kits change suspension geometry and tire-to-brake-line clearance. This bracket restores safe routing at any lift height. Compatibility Make Model Years Jeep Wrangler JK (2 & 4 Door) 2007-2018 Jeep Wrangler JL (2 & 4 Door) 2018-2023 Specifications Specification Detail Part Reference 1101255 Material Laser-cut ABS-grade steel Finish Black Fitment Front left & right SKU FJ-JP-BC02-CK Frequently Asked Questions Q: One bracket or two needed?A: Sold individually. One per side — order 2 for complete front brake line protection. Q: Aftermarket brake line compatible?A: Yes — works with factory and any aftermarket extended brake lines using factory mount points. Q: Drilling required?A: Zero — uses existing factory bolt holes. Bolt-on installation with basic hand tools. Q: Black vs Red version?A: Same design, different color. Black for stealth OEM+ look, Red (SKU FJ-JP-BC02-RD) for color matching. Q: Needed with extended brake lines?A: Extended lines add length but don't fix routing. If lines can still contact tires, this bracket provides positive separation. Related Products Brake Line Anchor Bracket — JK/JL Extended Brake Lines — JK 4-6" Lift Extended Brake Lines — XJ/YJ/TJ Related Blog Posts iFJF Guides — Installation & Maintenance Tips Jeep Wrangler Lift Kit Buyer's Guide

Read more less

Product Overview Stop leaks and reduce wind noise with these replacement hard top roof seal strips for Jeep Wrangler JK and JL models. Over time, factory roof seals harden, crack, and lose their ability to create a watertight barrier. The result? Water drips on your lap during rain and howling wind noise that ruins highway conversations. This 2-pack replaces the seal strips that run between your windshield frame and Freedom hard top. Made from UV-resistant EPDM rubber that stays pliable in extreme temperatures and won't degrade from sun exposure. Self-adhesive backing for easy installation clean the channel, peel, press, done. Key Features UV-Resistant EPDM Rubber Won't harden, crack, or degrade from sun exposure like cheaper rubber seals. Maintains flexibility from -40F to +200F. Waterproof & Dustproof Creates a tight seal that prevents rain, car wash water, and trail dust from entering the cabin through the windshield-hard top gap. Wind Noise Reduction Fresh seals eliminate the whistling and fluttering sounds that come from worn or missing weatherstripping. 2-Pack Coverage Includes both driver and passenger side seal strips. Complete roof-to-windshield sealing in one purchase. Self-Adhesive Backing Peel-and-stick installation. Clean the channel thoroughly before application for best adhesion. 15-20 minutes. Compatibility Year Make Model Top Type 2007-2018 Jeep Wrangler JK / JKU Freedom Hard Top 2018-2022 Jeep Wrangler JL / JLU Freedom Hard Top Specifications Spec Value Material EPDM Rubber (UV-Resistant) Quantity 2-Pack (Driver + Passenger Side) Attachment Self-Adhesive Backing Temperature Range -40F to +200F Frequently Asked Questions Q: Will these seal strips fit my 2020 Jeep Wrangler JL?A: Yes. These roof seal strips fit 2007-2018 JK/JKU and 2018-2022 JL/JLU with the factory Freedom hard top. Q: How do I know if I need new seal strips?A: Signs include: water leaks near windshield top during rain, excessive wind noise at highway speeds, visible cracks or flattening of original seal, or hardened rubber. Q: Do these reduce wind noise?A: Yes. Worn roof seals are a primary cause of wind noise. Fresh seals create a tight barrier, significantly reducing wind whistle and buffeting at highway speeds. Q: Is installation difficult?A: Clean the mounting channel, peel backing tape, press seal into channel. Let set before installing hard top. 15-20 minutes per side. Q: Are these the same as factory seals?A: Same profile and dimensions as OEM, using UV-resistant EPDM rubber. Matches factory fit with improved weather resistance for longer life.

Read more less

High-Performance Racing Thermostat for Hemi Engines Upgrade your Chrysler or Dodge Hemi-powered vehicle with the iFJF Racing Performance Thermostat. Engineered to open at a lower temperature than the OEM thermostat, this upgrade allows coolant to circulate earlier, keeping your engine running cooler under hard driving conditions. Whether you're hitting the track, towing heavy loads, or pushing your Hemi on the street, reduced engine temperatures mean more consistent power, less knock retard, and extended engine longevity. Vehicle Compatibility Make Model Year Range Engine Chrysler 300 / 300C 2005-2013 5.7L / 6.1L / 6.4L Hemi Dodge Charger 2006-2013 5.7L / 6.1L / 6.4L Hemi Dodge Challenger 2008-2013 5.7L / 6.1L / 6.4L Hemi Dodge Magnum 2005-2008 5.7L / 6.1L Hemi Key Features & Benefits Lower Activation Temperature: Opens at a reduced temp vs OEM, allowing earlier coolant flow and better heat management Consistent Power Output: Prevents heat soak and timing pull under high-load conditions Extended Engine Life: Reduced thermal stress on pistons, rings, and head gaskets Direct Fit Replacement: Designed to fit the stock thermostat housing — no modifications required Track-Tested Design: Popular upgrade among Hemi drag racers and road course enthusiasts Technical Specifications Specification Detail Part Number FJ-TAT02-06L Material Brass & Stainless Steel Compatible Engines 5.7L Hemi, 6.1L Hemi, 6.4L Hemi Installation Direct bolt-in, stock housing Application Street Performance / Track / Towing Why Upgrade Your Thermostat? Factory thermostats are calibrated for emissions compliance and cabin heat — not performance. Under spirited driving or track use, the stock thermostat keeps the engine in a higher temperature range that triggers ECU timing retardation. By installing a racing thermostat, you create a thermal buffer that helps your Hemi maintain optimal timing advance and horsepower output across the entire powerband. Frequently Asked Questions Q: Does this thermostat work with stock cooling systems?A: Yes. It installs in the factory thermostat housing and works with the stock radiator, water pump, and cooling fans. No other modifications are required. Q: What temperature does this thermostat open at?A: This racing thermostat opens at approximately 180°F, compared to the factory 203°F thermostat. This provides a 20-25°F thermal buffer during hard driving. Q: Will this cause a check engine light?A: In most applications, no. However, if you live in an extremely cold climate and the engine fails to reach operating temperature quickly, the ECU may set a P0128 code. This is rare and typically only occurs in sub-zero conditions. Q: Is this thermostat compatible with aftermarket tunes?A: Yes, and it actually works very well with performance tunes. Many tuners adjust fan activation temperatures to complement a lower-temp thermostat for maximum cooling efficiency. Q: Does this fit the 6.4L Apache / 392 Hemi?A: This thermostat fits Gen III Hemi engines including the 6.4L (392) Apache variant found in later SRT models. Verify your specific year and model compatibility in the table above.

Read more less